Satellite L300D boots into a blank screen with mouse cursor
Hi,
I have been asked by friends of mine to help them fix their L300D. Their son got to it and they are not sure what he did, but now when it loads into VIsta, all they get is a Black Screen with a mouse cursor in the middle. The cursor looks as if it is at a lower resolution than the normal display.
I thought this would easily be fixed by running a restore, but it does the same thing when I load the restore function (via holding 0 on boot), and even the copy of Windows 7 I tried to install as well.
I think it might be a hardware issue, but before getting them to contact Toshiba Service for a warranty repair, I thought I would post here and see if anyone has any suggestions on what it could be.
Hello
Well buddy, if the same issue appears if you load the restore function and also with Windows 7 I think its a hardware issue.
You can try to load the default settings in BIOS Maybe it works.
To be honest I think the best way is you contact the nearest authorized service provider. The technicians can check the notebook and exchange the hardware if there is a hardware problem.
Greets
Similar Messages
-
New Install - startx results in blank screen with mouse cursor
I installed Arch on my desktop last week with no issues, so I wanted to install it on an old THinkpad R31. Everything with the installation went smooth, but when I try to 'startx' all I get is a blank screen with a mouse cursor that I can move around. I've installed xorg-xinit, xorg-twm, xorg-xclock, and xterm.
I'm not getting any significant errors in the logs, or even the terminal I issue 'startx' in.
I'm not sure what the problem could be...
Here is my output from 'startx'
X.Org X Server 1.13.0
Release Date: 2012-09-05
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.6.0-1-ARCH i686
Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
Build Date: 05 October 2012 02:01:30PM
Current version of pixman: 0.26.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 09:26:12 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension SECURITY
Initializing built-in extension XINERAMA
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension RECORD
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
xinit: connection to X server lost
waiting for X server to shut down XIO: fatal IO error 0 (Success) on X server ":0"
after 554 requests (554 known processed) with 0 events remaining.
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
Server terminated successfully (0). Closing log file.
xinit: unexpected signal 2
And my Xorg.0.log
[ 4955.478]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 4955.479] X Protocol Version 11, Revision 0
[ 4955.479] Build Operating System: Linux 3.6.0-1-ARCH i686
[ 4955.479] Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
[ 4955.479] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
[ 4955.479] Build Date: 05 October 2012 02:01:30PM
[ 4955.479]
[ 4955.479] Current version of pixman: 0.26.2
[ 4955.479] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 4955.479] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 4955.480] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 09:26:12 2012
[ 4955.480] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 4955.480] (==) No Layout section. Using the first Screen section.
[ 4955.480] (==) No screen section available. Using defaults.
[ 4955.480] (**) |-->Screen "Default Screen Section" (0)
[ 4955.480] (**) | |-->Monitor "<default monitor>"
[ 4955.481] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 4955.481] (==) Automatically adding devices
[ 4955.481] (==) Automatically enabling devices
[ 4955.481] (==) Automatically adding GPU devices
[ 4955.481] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 4955.481] Entry deleted from font path.
[ 4955.481] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 4955.481] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 4955.481] Entry deleted from font path.
[ 4955.481] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 4955.481] (==) FontPath set to:
/usr/share/fonts/misc/
[ 4955.481] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 4955.481] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 4955.481] (II) Loader magic: 0x825a620
[ 4955.482] (II) Module ABI versions:
[ 4955.482] X.Org ANSI C Emulation: 0.4
[ 4955.482] X.Org Video Driver: 13.0
[ 4955.482] X.Org XInput driver : 18.0
[ 4955.482] X.Org Server Extension : 7.0
[ 4955.484] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4955.486] (--) PCI:*(0:0:2:0) 8086:3577:1014:0505 rev 4, Mem @ 0x98000000/134217728, 0x90100000/524288
[ 4955.486] (--) PCI: (0:0:2:1) 8086:3577:1014:0505 rev 0, Mem @ 0x88000000/134217728, 0x80200000/524288
[ 4955.486] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 4955.486] Initializing built-in extension Generic Event Extension
[ 4955.486] Initializing built-in extension SHAPE
[ 4955.486] Initializing built-in extension MIT-SHM
[ 4955.486] Initializing built-in extension XInputExtension
[ 4955.486] Initializing built-in extension XTEST
[ 4955.486] Initializing built-in extension BIG-REQUESTS
[ 4955.486] Initializing built-in extension SYNC
[ 4955.487] Initializing built-in extension XKEYBOARD
[ 4955.487] Initializing built-in extension XC-MISC
[ 4955.487] Initializing built-in extension SECURITY
[ 4955.487] Initializing built-in extension XINERAMA
[ 4955.487] Initializing built-in extension XFIXES
[ 4955.487] Initializing built-in extension RENDER
[ 4955.487] Initializing built-in extension RANDR
[ 4955.487] Initializing built-in extension COMPOSITE
[ 4955.487] Initializing built-in extension DAMAGE
[ 4955.487] Initializing built-in extension MIT-SCREEN-SAVER
[ 4955.487] Initializing built-in extension DOUBLE-BUFFER
[ 4955.487] Initializing built-in extension RECORD
[ 4955.487] Initializing built-in extension DPMS
[ 4955.487] Initializing built-in extension X-Resource
[ 4955.487] Initializing built-in extension XVideo
[ 4955.487] Initializing built-in extension XVideo-MotionCompensation
[ 4955.487] Initializing built-in extension XFree86-VidModeExtension
[ 4955.487] Initializing built-in extension XFree86-DGA
[ 4955.487] Initializing built-in extension XFree86-DRI
[ 4955.487] Initializing built-in extension DRI2
[ 4955.487] (II) LoadModule: "glx"
[ 4955.488] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 4955.489] (II) Module glx: vendor="X.Org Foundation"
[ 4955.489] compiled for 1.13.0, module version = 1.0.0
[ 4955.489] ABI class: X.Org Server Extension, version 7.0
[ 4955.489] (==) AIGLX enabled
[ 4955.489] Loading extension GLX
[ 4955.489] (==) Matched intel as autoconfigured driver 0
[ 4955.489] (==) Matched intel as autoconfigured driver 1
[ 4955.489] (==) Matched vesa as autoconfigured driver 2
[ 4955.489] (==) Matched modesetting as autoconfigured driver 3
[ 4955.489] (==) Matched fbdev as autoconfigured driver 4
[ 4955.489] (==) Assigned the driver to the xf86ConfigLayout
[ 4955.489] (II) LoadModule: "intel"
[ 4955.490] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 4955.491] (II) Module intel: vendor="X.Org Foundation"
[ 4955.491] compiled for 1.13.0, module version = 2.20.9
[ 4955.491] Module class: X.Org Video Driver
[ 4955.491] ABI class: X.Org Video Driver, version 13.0
[ 4955.491] (II) LoadModule: "vesa"
[ 4955.491] (WW) Warning, couldn't open module vesa
[ 4955.491] (II) UnloadModule: "vesa"
[ 4955.492] (II) Unloading vesa
[ 4955.492] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 4955.492] (II) LoadModule: "modesetting"
[ 4955.492] (WW) Warning, couldn't open module modesetting
[ 4955.492] (II) UnloadModule: "modesetting"
[ 4955.492] (II) Unloading modesetting
[ 4955.492] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 4955.493] (II) LoadModule: "fbdev"
[ 4955.493] (WW) Warning, couldn't open module fbdev
[ 4955.493] (II) UnloadModule: "fbdev"
[ 4955.493] (II) Unloading fbdev
[ 4955.493] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 4955.493] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+),
ValleyView PO board
[ 4955.496] (--) using VT number 7
[ 4955.508] (II) intel(0): using device path '/dev/dri/card0'
[ 4955.509] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 4955.509] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 4955.509] (==) intel(0): RGB weight 888
[ 4955.509] (==) intel(0): Default visual is TrueColor
[ 4955.509] (--) intel(0): Integrated Graphics Chipset: Intel(R) i830M
[ 4955.509] (**) intel(0): Relaxed fencing disabled
[ 4955.509] (**) intel(0): Wait on SwapBuffers? enabled
[ 4955.509] (**) intel(0): Triple buffering? enabled
[ 4955.509] (**) intel(0): Framebuffer tiled
[ 4955.510] (**) intel(0): Pixmaps tiled
[ 4955.510] (**) intel(0): 3D buffers tiled
[ 4955.510] (**) intel(0): SwapBuffers wait enabled
[ 4955.510] (==) intel(0): video overlay key set to 0x101fe
[ 4955.593] (II) intel(0): Output VGA1 has no monitor section
[ 4955.593] (II) intel(0): Output LVDS1 has no monitor section
[ 4955.594] (--) intel(0): found backlight control interface /sys/class/backlight/thinkpad_screen
[ 4955.676] (II) intel(0): EDID for output VGA1
[ 4955.677] (II) intel(0): Printing probed modes for output VGA1
[ 4955.677] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 4955.677] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 4955.677] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 4955.677] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 4955.677] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e)
[ 4955.677] (II) intel(0): EDID for output LVDS1
[ 4955.677] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Printing probed modes for output LVDS1
[ 4955.678] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync (48.4 kHz P)
[ 4955.678] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 4955.678] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 4955.678] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 4955.678] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 4955.678] (II) intel(0): Output VGA1 connected
[ 4955.678] (II) intel(0): Output LVDS1 connected
[ 4955.678] (II) intel(0): Using exact sizes for initial modes
[ 4955.678] (II) intel(0): Output VGA1 using initial mode 1024x768
[ 4955.678] (II) intel(0): Output LVDS1 using initial mode 1024x768
[ 4955.678] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 4955.678] (II) intel(0): Kernel page flipping support detected, enabling
[ 4955.678] (==) intel(0): DPI set to (96, 96)
[ 4955.678] (II) Loading sub module "fb"
[ 4955.678] (II) LoadModule: "fb"
[ 4955.679] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 4955.679] (II) Module fb: vendor="X.Org Foundation"
[ 4955.679] compiled for 1.13.0, module version = 1.0.0
[ 4955.679] ABI class: X.Org ANSI C Emulation, version 0.4
[ 4955.679] (II) Loading sub module "dri2"
[ 4955.679] (II) LoadModule: "dri2"
[ 4955.680] (II) Module "dri2" already built-in
[ 4955.680] (==) Depth 24 pixmap format is 32 bpp
[ 4955.680] (II) intel(0): [DRI2] Setup complete
[ 4955.680] (II) intel(0): [DRI2] DRI driver: i915
[ 4955.680] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
[ 4955.680] (II) UXA(0): Driver registered support for the following operations:
[ 4955.680] (II) solid
[ 4955.680] (II) copy
[ 4955.680] (II) composite (RENDER acceleration)
[ 4955.680] (II) put_image
[ 4955.680] (II) get_image
[ 4955.680] (==) intel(0): Backing store disabled
[ 4955.680] (==) intel(0): Silken mouse enabled
[ 4955.681] (II) intel(0): Initializing HW Cursor
[ 4955.681] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 4955.684] (==) intel(0): DPMS enabled
[ 4955.684] (==) intel(0): Intel XvMC decoder disabled
[ 4955.684] (II) intel(0): Set up overlay video
[ 4955.684] (II) intel(0): direct rendering: DRI2 Enabled
[ 4955.684] (==) intel(0): hotplug detection: "enabled"
[ 4955.983] (--) RandR disabled
[ 4956.021] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 4956.021] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 4956.021] (II) AIGLX: enabled GLX_ARB_create_context
[ 4956.021] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 4956.021] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 4956.021] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 4956.021] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 4956.021] (II) AIGLX: Loaded and initialized i915
[ 4956.022] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 4956.023] (II) intel(0): Setting screen physical size to 270 x 203
[ 4956.124] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 4956.124] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4956.124] (II) LoadModule: "evdev"
[ 4956.124] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 4956.125] (II) Module evdev: vendor="X.Org Foundation"
[ 4956.125] compiled for 1.13.0, module version = 2.7.3
[ 4956.125] Module class: X.Org XInput Driver
[ 4956.125] ABI class: X.Org XInput driver, version 18.0
[ 4956.125] (II) Using input driver 'evdev' for 'Power Button'
[ 4956.125] (**) Power Button: always reports core events
[ 4956.125] (**) evdev: Power Button: Device: "/dev/input/event4"
[ 4956.126] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4956.126] (--) evdev: Power Button: Found keys
[ 4956.126] (II) evdev: Power Button: Configuring as keyboard
[ 4956.126] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[ 4956.126] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 4956.126] (**) Option "xkb_rules" "evdev"
[ 4956.126] (**) Option "xkb_model" "evdev"
[ 4956.126] (**) Option "xkb_layout" "us"
[ 4956.197] (II) config/udev: Adding input device Video Bus (/dev/input/event2)
[ 4956.198] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 4956.198] (II) Using input driver 'evdev' for 'Video Bus'
[ 4956.198] (**) Video Bus: always reports core events
[ 4956.198] (**) evdev: Video Bus: Device: "/dev/input/event2"
[ 4956.198] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 4956.198] (--) evdev: Video Bus: Found keys
[ 4956.198] (II) evdev: Video Bus: Configuring as keyboard
[ 4956.198] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:00/input/input2/event2"
[ 4956.198] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 4956.198] (**) Option "xkb_rules" "evdev"
[ 4956.198] (**) Option "xkb_model" "evdev"
[ 4956.198] (**) Option "xkb_layout" "us"
[ 4956.200] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
[ 4956.200] (II) No input driver specified, ignoring this device.
[ 4956.200] (II) This device may have been added with another device file.
[ 4956.201] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[ 4956.201] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 4956.201] (II) Using input driver 'evdev' for 'Sleep Button'
[ 4956.202] (**) Sleep Button: always reports core events
[ 4956.202] (**) evdev: Sleep Button: Device: "/dev/input/event1"
[ 4956.202] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 4956.202] (--) evdev: Sleep Button: Found keys
[ 4956.202] (II) evdev: Sleep Button: Configuring as keyboard
[ 4956.202] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1/event1"
[ 4956.202] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[ 4956.202] (**) Option "xkb_rules" "evdev"
[ 4956.202] (**) Option "xkb_model" "evdev"
[ 4956.202] (**) Option "xkb_layout" "us"
[ 4956.204] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4956.205] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 4956.205] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 4956.205] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 4956.205] (**) AT Translated Set 2 keyboard: always reports core events
[ 4956.205] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 4956.205] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 4956.205] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 4956.205] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 4956.205] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 4956.205] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 4956.205] (**) Option "xkb_rules" "evdev"
[ 4956.206] (**) Option "xkb_model" "evdev"
[ 4956.206] (**) Option "xkb_layout" "us"
[ 4956.208] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/event6)
[ 4956.208] (**) TPPS/2 IBM TrackPoint: Applying InputClass "evdev pointer catchall"
[ 4956.208] (II) Using input driver 'evdev' for 'TPPS/2 IBM TrackPoint'
[ 4956.208] (**) TPPS/2 IBM TrackPoint: always reports core events
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: Device: "/dev/input/event6"
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Vendor 0x2 Product 0xa
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found 3 mouse buttons
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found relative axes
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found x and y relative axes
[ 4956.208] (II) evdev: TPPS/2 IBM TrackPoint: Configuring as mouse
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: YAxisMapping: buttons 4 and 5
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4956.208] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input6/event6"
[ 4956.208] (II) XINPUT: Adding extended input device "TPPS/2 IBM TrackPoint" (type: MOUSE, id 10)
[ 4956.209] (II) evdev: TPPS/2 IBM TrackPoint: initialized for relative axes.
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) keeping acceleration scheme 1
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration profile 0
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration factor: 2.000
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration threshold: 4
[ 4956.210] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/mouse0)
[ 4956.210] (II) No input driver specified, ignoring this device.
[ 4956.210] (II) This device may have been added with another device file.
[ 4956.211] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[ 4956.211] (II) No input driver specified, ignoring this device.
[ 4956.211] (II) This device may have been added with another device file.
[ 4956.213] (II) config/udev: Adding input device ThinkPad Extra Buttons (/dev/input/event7)
[ 4956.213] (**) ThinkPad Extra Buttons: Applying InputClass "evdev keyboard catchall"
[ 4956.213] (II) Using input driver 'evdev' for 'ThinkPad Extra Buttons'
[ 4956.213] (**) ThinkPad Extra Buttons: always reports core events
[ 4956.213] (**) evdev: ThinkPad Extra Buttons: Device: "/dev/input/event7"
[ 4956.214] (--) evdev: ThinkPad Extra Buttons: Vendor 0x1014 Product 0x5054
[ 4956.214] (--) evdev: ThinkPad Extra Buttons: Found keys
[ 4956.214] (II) evdev: ThinkPad Extra Buttons: Configuring as keyboard
[ 4956.214] (**) Option "config_info" "udev:/sys/devices/platform/thinkpad_acpi/input/input7/event7"
[ 4956.214] (II) XINPUT: Adding extended input device "ThinkPad Extra Buttons" (type: KEYBOARD, id 11)
[ 4956.214] (**) Option "xkb_rules" "evdev"
[ 4956.214] (**) Option "xkb_model" "evdev"
[ 4956.214] (**) Option "xkb_layout" "us"
[ 4960.630] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 4964.186] (II) evdev: ThinkPad Extra Buttons: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: TPPS/2 IBM TrackPoint: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: AT Translated Set 2 keyboard: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: Sleep Button: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: Video Bus: Close
[ 4964.190] (II) UnloadModule: "evdev"
[ 4964.190] (II) evdev: Power Button: Close
[ 4964.190] (II) UnloadModule: "evdev"
[ 4964.192] Server terminated successfully (0). Closing log file.karol wrote:
Leonid.I wrote:@0x001A4:
To run twm, you need to install xorg-twm from [extra] (I am not sure if it installs by default). Do you have xterm installed?
According to his first post he has both xorg-twm and xterm installed.
I do indeed.
I went ahead and installed LXDE anyways, just to see what would happen. Exact same thing, it looks like everything is about to load but only the mouse cursor shows up. My Xorg.0.log is the same, so I won't post it again.
I do get an error in the console about the openbox menu.xml file missing but I doubt that's related.
X.Org X Server 1.13.0
Release Date: 2012-09-05
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.6.0-1-ARCH i686
Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
Build Date: 05 October 2012 02:01:30PM
Current version of pixman: 0.26.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Oct 15 18:12:28 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension SECURITY
Initializing built-in extension XINERAMA
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension RECORD
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
Openbox-Message: Unable to find a valid menu file "/usr/share/lxde/openbox/menu.xml"
xinit: connection to X server lost
waiting for X server to shut down pcmanfm: Fatal IO error 11 (Resource temporarily unavailable) on X server :0.
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0"
after 2326 requests (2323 known processed) with 0 events remaining.
Server terminated successfully (0). Closing log file.
xinit: unexpected signal 2
.xinitrc for my user
exec ck-launch-session startlxde
Very wierd. -
Hp Pavilion 23 Blank Screen With Mouse Cursor After Hp Logo (Not Windows Logo)
Hello my computer wont start up all i get is a black screen but i have a mouse cursor. after a little bit the computer will restart and do a automatic repair but nothing happens it just keeps on rebooting. i tired to do a bio update but it seems to not be working. there is no option in the bios to update or even in UEFI. i also did a harddrive test and got a Short DST Check fail (FAILURE ID: 909HVX-0007K0-WPU2XF-60WH03) but i still can get access to the harddrive using a Linux LiveUSB and all files are there. (Product Number Is : H5P60AAR#ABA)
It is possible to receive a false DST check but not common.
It doesn't mean your hard has failed but that it is in imminent danger of failing.
You can try again but this time using the Extended DST test.
But before doing anything I suggest you back up all your important data using that live Linux boot disk just in case.
Every hard disk manufacturer has their own diagnostic boot cd/usb. Google it.
You should create one and run it for your brand hard drive.
You should be able to determine which brand you have from the BIOS/UEFI hardware tab.
While your'e in there double check that your boot priority is set to hard drive first.
Your other issue seems to be the dreaded 'Automatic Repair Loop' which could be caused by your possibly failing hard dirve. I would fully diagnose the hard drive first.
Here's a link with several suggested fixes. Some of them require a Windows 8 boot disk, other do not.
Automatic Repair Loop Fixes
If you found my answer helpful please say thanks by clicking on the Thumb's Up icon. Thanks! -
MacBook Pro suddenly will not boot up. Blank screen with message File is possibly corrupt. Header checksum does not match, etc
Hi s.cheslik,
It seems your MacBook Pro will not boot properly and it displaying an error message. Based on the information you have provided, it appears your MacBook Pro needs to be serviced. The following link should help you get started with the process and has links with additional information on topics such as warranty and service pricing, battery replacement, and express replacement service.
Apple - Support - Service Answer Center
Thank you for contributing to Apple Support Communities.
Take care,
Bobby_D -
Will a new MotherBoard cure Blank Screen with blinking cursor?
Stuck with Blank Screen with blinking cursor; ESC key couldn’t bring up Startup Menu; OS is not loading
Product Name: HP G62 237 CA Notebook PC
Short description of the problems:
--- Press ESC key couldn’t bring up Startup Menu when booting up
--- Blank screen with blinking cursor thereafter
--- Stuck here forever and OS is not loading
DETAILED INFORMATION:
Product Name and Operating System:
Model: HP G62 237 CA Notebook PC
O/S: Pre-loaded with Win 7 Home Prem
Processor: Pent. Dual-Core CPU T4500 2.30GHz
Memory: 4GB
BIOS Ver. (Insyde): F.17
System BOARD ID: 1484
Product #: WQ767UA#ABC
Product Config ID: 049C110000202710000020000
Problem History:
--- Used to have frequent BSOD (got fixed later because of faulty RAM that I suspected)
--- Window couldn’t be loaded
--- Window Repair and HP Recovery were tried but not functioning
--- OEM Hard Drive was then removed & formatted few times by using other computer
--- Hard Drive was then tested by other computer; it can be installed Win XP & Win 7
--- So, Hard Drive was eliminated from the suspect list
--- Replaced with other good RAM from other computers & put back the OEM Hard Drive to my HP G62; everything worked fine, such as: able to reinstall Win 7; listening to music files; got Internet to download latest BIOS from HP support site; connected to my 42 inched TV as my monitor; and even smoothly updated the BIOS from v.17 to v.37!
--- Also, able to receive Window Updates from the Internet; and seemed that all problems were nicely solved
--- Once I believe my system got stabilized; I went back to test the 2 supposedly problematic RAM to see whether they were both faulty or not, then the whole thing has turned around! Completely screwed me up until this moment …
--- After put back the problematic RAM, Window couldn’t be loaded …
--- With a few error messages… such as,
--- The file is possibly corrupt. The file header checksum does not match the computed checksum;
--- After the next reboot… an unexpected screen message showed up:
Intel ® Cantiga PCI Accelerated SVGA BIOS
Build Number: 1932 PC 14.34 11/11/2009 02:36:14
DECOMPILATION OR DISASSEMBLY PROHIBITED
Copyright © 2000-2003 Intel Corp. All Rights Reserved.
--- After that, OS was not loading …
--- Press ESC key couldn’t bring up the Startup Menu during boot up
--- Blank screen with blinking cursor thereafter and seems stuck here forever
Procedures performed for troubleshooting:
Tried hard reset for more than 5 times (removed battery, AC adapter disconnected and then hold down the Power button for more than 60 secs) and tried reseating memory too; same result with Blank Screen with blinking cursor after each reboot.
Connected to an external monitor [Fn + F4/F5] to see whether there was any display, nothing has showed on the external monitor, it seemed that no connection established between the two.
Finally, took the long journey to follow the Service and Maintenance Guide of HP G62 to remove the CMOS battery for well over 15 minutes and put it back. But the result was again disappointed. Tried 4 times already. The latest error message is:
The CMOS checksum is invalid. The CMOS will be reset to the default configuration and will be rebooted. Please check your BIOS Setup options to see if they change.
CMOS Reset (502)
ENTER – Reboot the system
After this message, the same Blank Screen with blinking cursor came back. And pressing the ESC key couldn’t bring up Startup Menu when booting up …
Note: the fan is still running; the Power button is functioning but seems stuck here forever!
I’ve already carefully read this HP Support document titled “HP BIOS Application Selected is Corrupt or Missing”:
http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443485#N144
If really is the BIOS problems, then I will have the difficulties of updating a Window-based BIOS when I couldn’t even load Window!
(Note: Boot from USB has no point because right now I couldn’t change the boot sequence because the various “Startup Menu” options are not showing up!)
Secondly, I am still stuck with the Blank Screen with a blinking cursor after I passed the first screen of “Press the ESC key for Startup Menu” when re-booted again!
Thirdly, I have formatted my Hard Drive more than 3 times during the last few days for testing; I don’t have the OEM pre-loaded Win 7 with me anyone … and I don’t think I have the UEFI installed previously on my system. I did try hold down the Win Key + B with the most updated BIOS in the attached USB …, it came back with the same blank screen with a cursor blinking after reboot.
Note: the Blank Screen I’m experiencing right now is not completely black, in fact, there is background light from behind the screen and on each reboot, I can see the HP logo and the left corner message of: “Press ESC key for Startup Menu” … So, I suppose that my computer screen is not physically broken at least.
Requests:
Please explain to me that what are the problem areas and the root causes if is possible?
What steps or other tests can be done to make it work again?
Do you think replacing the entire MotherBoard can cure the Blank Screen with blinking cursor?
[Warranty: expired! I am the original purchaser & the end-user of this HP G62; acquired 2 years ago directly from a trustworthy source: staples (in Canada). Would HP Support still willing to service it for an extra charge?]
Thanks in advance for any suggestion and idea!
Owenson
===========================================Stuck with Blank Screen with blinking cursor; ESC key couldn’t bring up Startup Menu; OS is not loading
Product Name: HP G62 237 CA Notebook PC
Short description of the problems:
--- Press ESC key couldn’t bring up Startup Menu when booting up
--- Blank screen with blinking cursor thereafter
--- Stuck here forever and OS is not loading
DETAILED INFORMATION:
Product Name and Operating System:
Model: HP G62 237 CA Notebook PC
O/S: Pre-loaded with Win 7 Home Prem
Processor: Pent. Dual-Core CPU T4500 2.30GHz
Memory: 4GB
BIOS Ver. (Insyde): F.17
System BOARD ID: 1484
Product #: WQ767UA#ABC
Product Config ID: 049C110000202710000020000
Problem History:
--- Used to have frequent BSOD (got fixed later because of faulty RAM that I suspected)
--- Window couldn’t be loaded
--- Window Repair and HP Recovery were tried but not functioning
--- OEM Hard Drive was then removed & formatted few times by using other computer
--- Hard Drive was then tested by other computer; it can be installed Win XP & Win 7
--- So, Hard Drive was eliminated from the suspect list
--- Replaced with other good RAM from other computers & put back the OEM Hard Drive to my HP G62; everything worked fine, such as: able to reinstall Win 7; listening to music files; got Internet to download latest BIOS from HP support site; connected to my 42 inched TV as my monitor; and even smoothly updated the BIOS from v.17 to v.37!
--- Also, able to receive Window Updates from the Internet; and seemed that all problems were nicely solved
--- Once I believe my system got stabilized; I went back to test the 2 supposedly problematic RAM to see whether they were both faulty or not, then the whole thing has turned around! Completely screwed me up until this moment …
--- After put back the problematic RAM, Window couldn’t be loaded …
--- With a few error messages… such as,
--- The file is possibly corrupt. The file header checksum does not match the computed checksum;
--- After the next reboot… an unexpected screen message showed up:
Intel ® Cantiga PCI Accelerated SVGA BIOS
Build Number: 1932 PC 14.34 11/11/2009 02:36:14
DECOMPILATION OR DISASSEMBLY PROHIBITED
Copyright © 2000-2003 Intel Corp. All Rights Reserved.
--- After that, OS was not loading …
--- Press ESC key couldn’t bring up the Startup Menu during boot up
--- Blank screen with blinking cursor thereafter and seems stuck here forever
Procedures performed for troubleshooting:
Tried hard reset for more than 5 times (removed battery, AC adapter disconnected and then hold down the Power button for more than 60 secs) and tried reseating memory too; same result with Blank Screen with blinking cursor after each reboot.
Connected to an external monitor [Fn + F4/F5] to see whether there was any display, nothing has showed on the external monitor, it seemed that no connection established between the two.
Finally, took the long journey to follow the Service and Maintenance Guide of HP G62 to remove the CMOS battery for well over 15 minutes and put it back. But the result was again disappointed. Tried 4 times already. The latest error message is:
The CMOS checksum is invalid. The CMOS will be reset to the default configuration and will be rebooted. Please check your BIOS Setup options to see if they change.
CMOS Reset (502)
ENTER – Reboot the system
After this message, the same Blank Screen with blinking cursor came back. And pressing the ESC key couldn’t bring up Startup Menu when booting up …
Note: the fan is still running; the Power button is functioning but seems stuck here forever!
I’ve already carefully read this HP Support document titled “HP BIOS Application Selected is Corrupt or Missing”:
http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443485#N144
If really is the BIOS problems, then I will have the difficulties of updating a Window-based BIOS when I couldn’t even load Window!
(Note: Boot from USB has no point because right now I couldn’t change the boot sequence because the various “Startup Menu” options are not showing up!)
Secondly, I am still stuck with the Blank Screen with a blinking cursor after I passed the first screen of “Press the ESC key for Startup Menu” when re-booted again!
Thirdly, I have formatted my Hard Drive more than 3 times during the last few days for testing; I don’t have the OEM pre-loaded Win 7 with me anyone … and I don’t think I have the UEFI installed previously on my system. I did try hold down the Win Key + B with the most updated BIOS in the attached USB …, it came back with the same blank screen with a cursor blinking after reboot.
Note: the Blank Screen I’m experiencing right now is not completely black, in fact, there is background light from behind the screen and on each reboot, I can see the HP logo and the left corner message of: “Press ESC key for Startup Menu” … So, I suppose that my computer screen is not physically broken at least.
Requests:
Please explain to me that what are the problem areas and the root causes if is possible?
What steps or other tests can be done to make it work again?
Do you think replacing the entire MotherBoard can cure the Blank Screen with blinking cursor?
[Warranty: expired! I am the original purchaser & the end-user of this HP G62; acquired 2 years ago directly from a trustworthy source: staples (in Canada). Would HP Support still willing to service it for an extra charge?]
Thanks in advance for any suggestion and idea!
Owenson
=========================================== -
My laptop L2000 lance Armstrong only boots to a black screen with a cursor.
My laptop only boots to a black screen with a cursor. Can this be because the board numbers may be different then whats on the HD? I swaped a HD from a old and ugly L2000 to a new and shiny looking laptop! dbarselow
Boot from the first of the system discs (by holding down the C key until the welcome screen goes away) and, in Disc Utility, repair privileges. Not just permissions, but privileges. Then reboot at normal. That will probably fix it.
-
I have a new Dell Inspiron 15R. I closed it without shutting it down and when I tried to start it up I get a blank screen with my cursor. What's wrong.
You may get a reply here but it's best to post a question in the columns it naturally belongs to; in this case Dell forums.
-
Server 2008 crash - black screen with mouse cursor
dell poweredge 2950 with Perc 5/I RAID, ESXi 4.1 host, Windows Server 2008 R2 SP1 VM
After swapping out a failed raid5 drive this vm began displaying inpage operation error popups while checking folder permissions. event viewer errors:
The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume2.
The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:.
chkdsk /r run from the win2k8r2sp1 install dvd command line resulted in more corrections than i was able to screenshot:
After this the server would only boot to black screen with mouse cursor. same black screen result in safe mode or directory services restore mode. sfc /scannow, startrep, and registry repair from the folder contents @ c:\windows\system32\config\regback
have been attempted with no improvement. I am still able to access the filesystem contents using the command line from the win2k8r2sp1 installation DVD - user + registry files copied over to another drive without problem and i was able to load
the registry hive on another system. This server was doing dns, domain controller and certification authority but the only important item is getting the CA back somehow. Any suggestions are welcome.Hi,
According the information you have provided, the file system is broken.
After the repair, do chkdsk /r and sfc /scannow give any warning or error?
If yes, it means that the file system and system file are not repaired. Please post the error or warning here. It may give some hints.
Best Regards.
Steven Lee
TechNet Community Support -
Gnome Black Screen with Mouse Cursor after Login
I am using Archlinux 64bit with a Gnome Desktop Environment. Everything was running normally uptill today. When i ran "sudo fc-cache", my system froze. I couldnt open any other app but i was able to access terminal. I restarted using "reboot" command. After that I was unable to log in to my desktop.
The Gnome login screen comes and after entering the correct username and password, all I can see is a black screen with mouse cursor. I then started gnome manually with "startx" and it worked. But still I am unable to use normally (that is the graphical login). I reinstalled gdm but it didnt work. Please help me out.there are a lot of processess running... dunno killing which process will not cause a problem
here is the xorg log ( sorry i dont have much knowlegde to analyse it )
[ 2957.489]
X.Org X Server 1.16.1
Release Date: 2014-09-21
[ 2957.493] X Protocol Version 11, Revision 0
[ 2957.494] Build Operating System: Linux 3.16.1-1-ARCH x86_64
[ 2957.495] Current Operating System: Linux defo-arch 3.17.1-1-ARCH #1 SMP PREEMPT Wed Oct 15 15:04:35 CEST 2014 x86_64
[ 2957.495] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=3c376af4-e330-4277-8bfa-388dabfced9e rw quiet
[ 2957.497] Build Date: 21 September 2014 10:53:13AM
[ 2957.498]
[ 2957.499] Current version of pixman: 0.32.6
[ 2957.501] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 2957.501] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2957.506] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Oct 26 01:36:27 2014
[ 2957.507] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 2957.507] (==) No Layout section. Using the first Screen section.
[ 2957.507] (==) No screen section available. Using defaults.
[ 2957.507] (**) |-->Screen "Default Screen Section" (0)
[ 2957.507] (**) | |-->Monitor "<default monitor>"
[ 2957.507] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 2957.507] (==) Automatically adding devices
[ 2957.507] (==) Automatically enabling devices
[ 2957.507] (==) Automatically adding GPU devices
[ 2957.507] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
[ 2957.507] Entry deleted from font path.
[ 2957.507] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2957.507] Entry deleted from font path.
[ 2957.507] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 2957.507] Entry deleted from font path.
[ 2957.507] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2957.507] Entry deleted from font path.
[ 2957.507] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2957.507] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2957.507] Entry deleted from font path.
[ 2957.507] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2957.507] (==) FontPath set to:
/usr/share/fonts/misc/
[ 2957.507] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2957.507] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2957.507] (II) Loader magic: 0x818d80
[ 2957.507] (II) Module ABI versions:
[ 2957.507] X.Org ANSI C Emulation: 0.4
[ 2957.507] X.Org Video Driver: 18.0
[ 2957.507] X.Org XInput driver : 21.0
[ 2957.507] X.Org Server Extension : 8.0
[ 2957.509] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c1
[ 2957.509] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 2957.510] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 8 paused 0
[ 2957.512] (--) PCI:*(0:0:2:0) 8086:2a02:1028:022f rev 12, Mem @ 0xfea00000/1048576, 0xe0000000/268435456, I/O @ 0x0000eff8/8
[ 2957.512] (--) PCI: (0:0:2:1) 8086:2a03:1028:022f rev 12, Mem @ 0xfeb00000/1048576
[ 2957.512] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 2957.512] (II) LoadModule: "glx"
[ 2957.512] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2957.514] (II) Module glx: vendor="X.Org Foundation"
[ 2957.514] compiled for 1.16.1, module version = 1.0.0
[ 2957.514] ABI class: X.Org Server Extension, version 8.0
[ 2957.514] (==) AIGLX enabled
[ 2957.514] (==) Matched intel as autoconfigured driver 0
[ 2957.514] (==) Matched intel as autoconfigured driver 1
[ 2957.514] (==) Matched modesetting as autoconfigured driver 2
[ 2957.514] (==) Matched fbdev as autoconfigured driver 3
[ 2957.514] (==) Matched vesa as autoconfigured driver 4
[ 2957.514] (==) Assigned the driver to the xf86ConfigLayout
[ 2957.514] (II) LoadModule: "intel"
[ 2957.514] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 2957.515] (II) Module intel: vendor="X.Org Foundation"
[ 2957.515] compiled for 1.16.1, module version = 2.99.916
[ 2957.515] Module class: X.Org Video Driver
[ 2957.515] ABI class: X.Org Video Driver, version 18.0
[ 2957.515] (II) LoadModule: "modesetting"
[ 2957.515] (WW) Warning, couldn't open module modesetting
[ 2957.515] (II) UnloadModule: "modesetting"
[ 2957.515] (II) Unloading modesetting
[ 2957.515] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 2957.515] (II) LoadModule: "fbdev"
[ 2957.515] (WW) Warning, couldn't open module fbdev
[ 2957.515] (II) UnloadModule: "fbdev"
[ 2957.515] (II) Unloading fbdev
[ 2957.515] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 2957.515] (II) LoadModule: "vesa"
[ 2957.515] (WW) Warning, couldn't open module vesa
[ 2957.515] (II) UnloadModule: "vesa"
[ 2957.515] (II) Unloading vesa
[ 2957.515] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 2957.515] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 2957.516] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000
[ 2957.516] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100
[ 2957.516] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300
[ 2957.516] (++) using VT number 1
[ 2957.516] (--) controlling tty is VT number 1, auto-enabling KeepTty
[ 2957.516] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20140725
[ 2957.516] (--) intel(0): Integrated Graphics Chipset: Intel(R) 965GM
[ 2957.517] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1
[ 2957.517] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 2957.517] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 2957.517] (==) intel(0): RGB weight 888
[ 2957.517] (==) intel(0): Default visual is TrueColor
[ 2957.517] (II) intel(0): Output LVDS1 has no monitor section
[ 2957.517] (--) intel(0): Found backlight control interface acpi_video0 (type 'firmware') for output LVDS1
[ 2957.517] (II) intel(0): Enabled output LVDS1
[ 2957.517] (II) intel(0): Output VGA1 has no monitor section
[ 2957.517] (II) intel(0): Enabled output VGA1
[ 2957.517] (II) intel(0): Output HDMI1 has no monitor section
[ 2957.517] (II) intel(0): Enabled output HDMI1
[ 2957.517] (II) intel(0): Output TV1 has no monitor section
[ 2957.517] (II) intel(0): Enabled output TV1
[ 2957.517] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[ 2957.517] (II) intel(0): Output VIRTUAL1 has no monitor section
[ 2957.517] (II) intel(0): Enabled output VIRTUAL1
[ 2957.517] (--) intel(0): Output LVDS1 using initial mode 1280x800 on pipe 1
[ 2957.517] (==) intel(0): TearFree disabled
[ 2957.517] (==) intel(0): DPI set to (96, 96)
[ 2957.517] (II) Loading sub module "dri2"
[ 2957.517] (II) LoadModule: "dri2"
[ 2957.517] (II) Module "dri2" already built-in
[ 2957.517] (II) Loading sub module "present"
[ 2957.517] (II) LoadModule: "present"
[ 2957.517] (II) Module "present" already built-in
[ 2957.517] (==) Depth 24 pixmap format is 32 bpp
[ 2957.518] (II) intel(0): SNA initialized with Broadwater (gen4) backend
[ 2957.518] (==) intel(0): Backing store enabled
[ 2957.518] (==) intel(0): Silken mouse enabled
[ 2957.518] (II) intel(0): HW Cursor enabled
[ 2957.518] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 2957.518] (==) intel(0): DPMS enabled
[ 2957.518] (II) intel(0): [XvMC] i965_xvmc driver initialized.
[ 2957.518] (II) intel(0): [DRI2] Setup complete
[ 2957.518] (II) intel(0): [DRI2] DRI driver: i965
[ 2957.518] (II) intel(0): [DRI2] VDPAU driver: i965
[ 2957.518] (II) intel(0): direct rendering: DRI2 enabled
[ 2957.518] (II) intel(0): hardware support for Present enabled
[ 2957.518] (==) intel(0): display hotplug detection enabled
[ 2957.518] (--) RandR disabled
[ 2957.569] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 2957.569] (II) AIGLX: enabled GLX_ARB_create_context
[ 2957.569] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 2957.569] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 2957.569] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 2957.569] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 2957.569] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 2957.569] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 2957.569] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 2957.569] (II) AIGLX: Loaded and initialized i965
[ 2957.569] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 2957.576] (II) intel(0): switch to mode [email protected] on LVDS1 using pipe 1, position (0, 0), rotation normal, reflection none
[ 2957.583] (II) intel(0): Setting screen physical size to 338 x 211
[ 2957.636] (II) config/udev: Adding input device Video Bus (/dev/input/event12)
[ 2957.636] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 2957.636] (II) LoadModule: "evdev"
[ 2957.636] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2957.637] (II) Module evdev: vendor="X.Org Foundation"
[ 2957.637] compiled for 1.16.0, module version = 2.9.0
[ 2957.637] Module class: X.Org XInput Driver
[ 2957.637] ABI class: X.Org XInput driver, version 21.0
[ 2957.637] (II) systemd-logind: got fd for /dev/input/event12 13:76 fd 15 paused 0
[ 2957.637] (II) Using input driver 'evdev' for 'Video Bus'
[ 2957.638] (**) Video Bus: always reports core events
[ 2957.638] (**) evdev: Video Bus: Device: "/dev/input/event12"
[ 2957.638] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 2957.638] (--) evdev: Video Bus: Found keys
[ 2957.638] (II) evdev: Video Bus: Configuring as keyboard
[ 2957.638] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input19/event12"
[ 2957.638] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 2957.638] (**) Option "xkb_rules" "evdev"
[ 2957.638] (**) Option "xkb_model" "pc104"
[ 2957.638] (**) Option "xkb_layout" "us"
[ 2957.669] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 2957.670] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2957.670] (II) systemd-logind: got fd for /dev/input/event2 13:66 fd 16 paused 0
[ 2957.670] (II) Using input driver 'evdev' for 'Power Button'
[ 2957.670] (**) Power Button: always reports core events
[ 2957.670] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 2957.670] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2957.670] (--) evdev: Power Button: Found keys
[ 2957.670] (II) evdev: Power Button: Configuring as keyboard
[ 2957.670] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6/event2"
[ 2957.670] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 2957.670] (**) Option "xkb_rules" "evdev"
[ 2957.670] (**) Option "xkb_model" "pc104"
[ 2957.670] (**) Option "xkb_layout" "us"
[ 2957.671] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 2957.671] (II) No input driver specified, ignoring this device.
[ 2957.671] (II) This device may have been added with another device file.
[ 2957.671] (II) config/udev: Adding input device Sleep Button (/dev/input/event3)
[ 2957.671] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 2957.672] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 17 paused 0
[ 2957.672] (II) Using input driver 'evdev' for 'Sleep Button'
[ 2957.672] (**) Sleep Button: always reports core events
[ 2957.672] (**) evdev: Sleep Button: Device: "/dev/input/event3"
[ 2957.672] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 2957.672] (--) evdev: Sleep Button: Found keys
[ 2957.672] (II) evdev: Sleep Button: Configuring as keyboard
[ 2957.672] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input7/event3"
[ 2957.672] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[ 2957.672] (**) Option "xkb_rules" "evdev"
[ 2957.672] (**) Option "xkb_model" "pc104"
[ 2957.672] (**) Option "xkb_layout" "us"
[ 2957.673] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event6)
[ 2957.673] (II) No input driver specified, ignoring this device.
[ 2957.673] (II) This device may have been added with another device file.
[ 2957.673] (II) config/udev: Adding input device HDA Intel HDMI/DP,pcm=3 (/dev/input/event7)
[ 2957.673] (II) No input driver specified, ignoring this device.
[ 2957.673] (II) This device may have been added with another device file.
[ 2957.673] (II) config/udev: Adding input device HDA Intel Front Headphone Front (/dev/input/event8)
[ 2957.673] (II) No input driver specified, ignoring this device.
[ 2957.673] (II) This device may have been added with another device file.
[ 2957.674] (II) config/udev: Adding input device HDA Intel Front Headphone Surround (/dev/input/event9)
[ 2957.674] (II) No input driver specified, ignoring this device.
[ 2957.674] (II) This device may have been added with another device file.
[ 2957.674] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 2957.674] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 2957.675] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 18 paused 0
[ 2957.675] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 2957.675] (**) AT Translated Set 2 keyboard: always reports core events
[ 2957.675] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 2957.675] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 2957.675] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 2957.675] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 2957.675] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 2957.675] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 2957.675] (**) Option "xkb_rules" "evdev"
[ 2957.675] (**) Option "xkb_model" "pc104"
[ 2957.675] (**) Option "xkb_layout" "us"
[ 2957.675] (II) config/udev: Adding input device AlpsPS/2 ALPS GlidePoint (/dev/input/event11)
[ 2957.675] (**) AlpsPS/2 ALPS GlidePoint: Applying InputClass "evdev touchpad catchall"
[ 2957.675] (**) AlpsPS/2 ALPS GlidePoint: Applying InputClass "touchpad catchall"
[ 2957.675] (**) AlpsPS/2 ALPS GlidePoint: Applying InputClass "Default clickpad buttons"
[ 2957.675] (II) LoadModule: "synaptics"
[ 2957.676] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 2957.676] (II) Module synaptics: vendor="X.Org Foundation"
[ 2957.676] compiled for 1.16.0, module version = 1.8.1
[ 2957.676] Module class: X.Org XInput Driver
[ 2957.676] ABI class: X.Org XInput driver, version 21.0
[ 2957.676] (II) systemd-logind: got fd for /dev/input/event11 13:75 fd 19 paused 0
[ 2957.676] (II) Using input driver 'synaptics' for 'AlpsPS/2 ALPS GlidePoint'
[ 2957.676] (**) AlpsPS/2 ALPS GlidePoint: always reports core events
[ 2957.676] (**) Option "Device" "/dev/input/event11"
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: x-axis range 0 - 1023 (res 0)
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: y-axis range 0 - 767 (res 0)
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: pressure range 0 - 127
[ 2957.710] (II) synaptics: AlpsPS/2 ALPS GlidePoint: device does not report finger width.
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: buttons: left right middle
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: Vendor 0x2 Product 0x8
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: invalid finger width range. defaulting to 0 - 15
[ 2957.710] (**) Option "TapButton1" "1"
[ 2957.710] (**) Option "TapButton2" "2"
[ 2957.710] (**) Option "TapButton3" "3"
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: touchpad found
[ 2957.710] (**) AlpsPS/2 ALPS GlidePoint: always reports core events
[ 2957.710] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input10/event11"
[ 2957.710] (II) XINPUT: Adding extended input device "AlpsPS/2 ALPS GlidePoint" (type: TOUCHPAD, id 10)
[ 2957.710] (**) synaptics: AlpsPS/2 ALPS GlidePoint: (accel) MinSpeed is now constant deceleration 2.5
[ 2957.710] (**) synaptics: AlpsPS/2 ALPS GlidePoint: (accel) MaxSpeed is now 1.75
[ 2957.710] (**) synaptics: AlpsPS/2 ALPS GlidePoint: (accel) AccelFactor is now 0.156
[ 2957.710] (**) AlpsPS/2 ALPS GlidePoint: (accel) keeping acceleration scheme 1
[ 2957.710] (**) AlpsPS/2 ALPS GlidePoint: (accel) acceleration profile 1
[ 2957.710] (**) AlpsPS/2 ALPS GlidePoint: (accel) acceleration factor: 2.000
[ 2957.710] (**) AlpsPS/2 ALPS GlidePoint: (accel) acceleration threshold: 4
[ 2957.710] (--) synaptics: AlpsPS/2 ALPS GlidePoint: touchpad found
[ 2957.711] (II) config/udev: Adding input device AlpsPS/2 ALPS GlidePoint (/dev/input/mouse1)
[ 2957.711] (**) AlpsPS/2 ALPS GlidePoint: Ignoring device from InputClass "touchpad ignore duplicates"
[ 2957.711] (II) config/udev: Adding input device ALPS PS/2 Device (/dev/input/event10)
[ 2957.711] (**) ALPS PS/2 Device: Applying InputClass "evdev pointer catchall"
[ 2957.712] (II) systemd-logind: got fd for /dev/input/event10 13:74 fd 20 paused 0
[ 2957.712] (II) Using input driver 'evdev' for 'ALPS PS/2 Device'
[ 2957.712] (**) ALPS PS/2 Device: always reports core events
[ 2957.712] (**) evdev: ALPS PS/2 Device: Device: "/dev/input/event10"
[ 2957.712] (--) evdev: ALPS PS/2 Device: Vendor 0x2 Product 0x8
[ 2957.712] (--) evdev: ALPS PS/2 Device: Found 3 mouse buttons
[ 2957.712] (--) evdev: ALPS PS/2 Device: Found relative axes
[ 2957.712] (--) evdev: ALPS PS/2 Device: Found x and y relative axes
[ 2957.712] (II) evdev: ALPS PS/2 Device: Configuring as mouse
[ 2957.712] (**) evdev: ALPS PS/2 Device: YAxisMapping: buttons 4 and 5
[ 2957.712] (**) evdev: ALPS PS/2 Device: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2957.712] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio2/input/input12/event10"
[ 2957.712] (II) XINPUT: Adding extended input device "ALPS PS/2 Device" (type: MOUSE, id 11)
[ 2957.712] (II) evdev: ALPS PS/2 Device: initialized for relative axes.
[ 2957.712] (**) ALPS PS/2 Device: (accel) keeping acceleration scheme 1
[ 2957.712] (**) ALPS PS/2 Device: (accel) acceleration profile 0
[ 2957.712] (**) ALPS PS/2 Device: (accel) acceleration factor: 2.000
[ 2957.712] (**) ALPS PS/2 Device: (accel) acceleration threshold: 4
[ 2957.713] (II) config/udev: Adding input device ALPS PS/2 Device (/dev/input/mouse0)
[ 2957.713] (II) No input driver specified, ignoring this device.
[ 2957.713] (II) This device may have been added with another device file.
[ 2957.713] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[ 2957.713] (II) No input driver specified, ignoring this device.
[ 2957.713] (II) This device may have been added with another device file.
[ 2957.714] (II) config/udev: Adding input device Dell WMI hotkeys (/dev/input/event5)
[ 2957.714] (**) Dell WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 2957.714] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 21 paused 0
[ 2957.714] (II) Using input driver 'evdev' for 'Dell WMI hotkeys'
[ 2957.714] (**) Dell WMI hotkeys: always reports core events
[ 2957.714] (**) evdev: Dell WMI hotkeys: Device: "/dev/input/event5"
[ 2957.714] (--) evdev: Dell WMI hotkeys: Vendor 0 Product 0
[ 2957.714] (--) evdev: Dell WMI hotkeys: Found keys
[ 2957.714] (II) evdev: Dell WMI hotkeys: Configuring as keyboard
[ 2957.714] (**) Option "config_info" "udev:/sys/devices/virtual/input/input11/event5"
[ 2957.714] (II) XINPUT: Adding extended input device "Dell WMI hotkeys" (type: KEYBOARD, id 12)
[ 2957.714] (**) Option "xkb_rules" "evdev"
[ 2957.714] (**) Option "xkb_model" "pc104"
[ 2957.714] (**) Option "xkb_layout" "us"
[ 2963.887] (II) evdev: Dell WMI hotkeys: Close
[ 2963.887] (II) UnloadModule: "evdev"
[ 2963.887] (II) systemd-logind: releasing fd for 13:69
[ 2963.949] (II) evdev: ALPS PS/2 Device: Close
[ 2963.950] (II) UnloadModule: "evdev"
[ 2963.950] (II) systemd-logind: releasing fd for 13:74
[ 2964.016] (II) UnloadModule: "synaptics"
[ 2964.016] (II) systemd-logind: releasing fd for 13:75
[ 2964.069] (II) evdev: AT Translated Set 2 keyboard: Close
[ 2964.070] (II) UnloadModule: "evdev"
[ 2964.070] (II) systemd-logind: releasing fd for 13:64
[ 2964.123] (II) evdev: Sleep Button: Close
[ 2964.123] (II) UnloadModule: "evdev"
[ 2964.123] (II) systemd-logind: releasing fd for 13:67
[ 2964.156] (II) evdev: Power Button: Close
[ 2964.156] (II) UnloadModule: "evdev"
[ 2964.156] (II) systemd-logind: releasing fd for 13:66
[ 2964.183] (II) evdev: Video Bus: Close
[ 2964.183] (II) UnloadModule: "evdev"
[ 2964.183] (II) systemd-logind: releasing fd for 13:76
[ 2964.271] (EE) Server terminated successfully (0). Closing log file. -
HELP with Satellite Series - P305-S8837; displaying blank screen with cursor
Help! I have a the P305-S8837 laptop in the Toshiba Satellite Series. I have had the laptop for several months now and it's been working fine until now. I was using it this morning (on the internet) and it started freezing up and so I hit Crtl + Alt + delete and selected the option to restart. It restarted and asked which mode I wanted to start it up in (safe mode, safe mode w/networking, etc.) and I selected the normal option. It started out fine - little windows logo came on with the sound and then went into the Welcome Windows Home Vista premium page (that's like bluish greenish) and then afterwards the screen just goes blank with the exception of the mouse cursor. I let it sit for about an hour and there was no change. I have tried pressing the Crtl + Alt + delete and that has had NO affect. So i manually turned it off and then back on using the power button and tried starting it up in Safe mode w/networking and then just safe mode - both are able to get to the welcome screen but after that it's just a blank screen with cursor and it says safe mode and stuff on the border. Crtl + Alt + delete does not work in the safe mode w/networking but in just the regular safe mode it will go to that same screen that is the welcome and ask if I want to lock the computer, change users, start task manager or restart / shut down. I have selected the restart option and nothing happens and then the Crtl + Alt + delete option no longer works. I have tried manually starting the laptop with the battery unattached and just using the AC Adapter and that has had no impact. I have tried just using the laptop's battery only with no AC Adapter and that has had no impact.
As you can see, I am in desperate need of some assistance! Please tell me what to do!
ThanksSatellite P305-S8837
Turn the computer on and immediately press and hold the F8 key.
On the Advanced Boot Options menu, choose Repair Your Computer.
When you reach the System Recovery Options menu, choose Startup Repair.
If that doesn't do the trick, go back to the System Recovery Options menu and do a System Restore.
If that doesn't fix things either, go back to the System Recovery Options menu, choose Command Prompt, and follow the directions here
How to use the Bootrec.exe tool in the Windows Recovery Environment to troubleshoot and repair start...
Good luck!
-Jerry -
Bootcamp 5.0 installation: Blank Screen with blinking cursor after restart
I have a late 2011 mbp with 16gb ram, 2 750gb hard drives. I'm trying to install bootcamp on the 2nd hard drive. I'm using the cd drive in an external usb housing to install windows 7 ISO burn. I've used this cd several times in the past with no issues. After creating the partition with bootcamp assistant, my mac restarts automatically then when it boots, it goes to a blank black screen with a blinking cursor. I have restarted and repeated this process several times, as well as let it set there for about 1 hour and still nothing...I've also tried sudo ram reset and command option p r but still nothing.
Anyone have any idea what's wrong?Ok guys, for those of you who are having the same problem...here are the instructions on how to get past the blank screen and install windows 7 bootcamp with TWO hard drives installed.
1. With both hard drives installed, start the bootcamp assistant (you need a usb optical drive with windows dvd inserted to do this). Partition your SECOND hard drive for windows.
2. When your computer restarts and your at the blank screen with the blinking cursor of doom, manually shut down your computer.
3. Remove both hard drives from your MBP. Put the "Bootcamp" partitioned hard drive in the main HD bay. MAC OS DOES NOT NEED TO BE INSTALLED ON THE "BOOTCAMP" HD TO DO THIS.
4. Install your optical drive back into its factory place. (Where the "BOOTCAMP" HD was just installed at)
5. Power back up your MBP while holding the alt/option key down. Make sure the windows DVD is still in the optical drive!
6. Click on windows cd to boot from.
7. Start installing.
8. When finished, replace optical drive with "BOOTCAMP" HD and put MAC OS HD back in like it was before this process.
9. Your finished.
10. Now enjoy! -
[SOLVED] log into KDE given a blank black screen with mouse cursor
hi,
noticed kwin using much higher cpu usage then normal, restarted KDE, everything seemed ok and then, while copying a file over to a samba share, my desktop went black with only a mouse cursor.
Restarted KDE, rebooted pc, reinstalled KDE (everything), xorg, nvidia, deleted xorg.conf created new user but nothing will give me my desktop back
once when i logged on, i had a kde crash report and messages on my widgets saying missing components. Tried to submit bug but missing debugging tools.
sometimes KDE won't log in at all.
forced an fsck on next boot with no errors found.
please help
thanks
EDIT: [solved] I had filled up my /var partition. cleaned pacman cache and all is good again. Phew!
Last edited by Fungyo (2009-12-07 08:10:40)Hi,
Have you tried the suggestion Cyber_Defend_Team provided?
If the issue persists, start the computer in Safe mode to check the result:
If it doesn't reappear when you start in safe mode, you can eliminate the default settings and basic device drivers as possible causes. If a recently installed program, device, or driver prevents Windows from running correctly, you can start your computer
in safe mode and then remove the program that's causing the problem.
If it still in the safe mode, we may need to repair the installation with the recovery media.
In addition, please logon the problematic computer with the domain user account which works fine in other computer to test to see if it's the user account issue.
Karen Hu
TechNet Community Support -
Black or blank screen with blinking cursor after entering Windows password
This document pertains to all HP computers and tablets with Windows 7 and Windows 8 (8.1).
You can also link directly to this document at this URL
http://support.hp.com/us-en/document/c04572861
Use the following steps if your computer stops at a black screen with a blinking cursor after entering the Windows password.
On the black screen, press Ctrl, Shift, ESC to open the Task Manager window.
note: If the Task Manager window does not open, see Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot.
Click the Process tab.
Look for one or both of the following tasks:
Run Once Wrapper
Run Once Wrapper (32-bit)
Right-click the task, and then click the End task button. Windows should start normally.
On the Windows 8 start screen type Control Panel then click Control Panel in the search results. In Windows 7, click Start then type Control Panel, then click Control Panel in the search results.
From the Windows Control Panel, go to Programs and Features or Add/Remove Programs.
Remove any of the following programs. Additionally, remove any other suspected programs that are not listed.
Remove these suspected programs:
Binkiland
SevenZip
Unchecky
Image Repair
SolutionReal
Vosteran
JetClean
Speed Browser
Web Bar 2.0.5273.16044
mypcbackup
Speed Checker
Wincheck
Omega Plus
Spy Clear
Word Proser
Optimizer Pro
Spyware Clear with PC Tech Hotline
WSE_Binkiland
Pepper Zip
Storm Watch
WSE_Taplika
Pro PC Cleaner
Strong Signal
WSE_Vosteran
Safe Search
Taplika
To resolve all other black/blank screen issues at boot, see Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot.
To resolve virus and malware issues, see About Spyware, Adware, and Browser Hijacking Software and Using Windows 8 Defender to Prevent Virus and Spyware Problems
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.This is not what happens. The screen goes black, no curser or anything, then it comes right back on to the same page I was on when it went out. It doesn't happen when I login, it happens as I am on a webpage or playing a online game.
-
Post-wake blank screen with mouse.
After waking up my iMac, it sometimes gives me a blank (black) screen with only the mouse showing. I can move the mouse, and pressing escape makes the 'not allowed' noise. It's a model 7.1 iMac running on an Intel Core 2 Duo and OSX 10.5.8. If anyone could help, it would be greatly appreciated.
What computer do you have? Check the label on the bottom for the model and part numbers.
- Peter -
Vista Home Premium: Following install, black screen with mouse cursor
I have tried installing with Boot Camp (v2.0) twice now with the same result.
After the install is complete, the mac reboots into windows. I should see the Vista welcome screen but instead I get the black screen with a mouse cursor. The mouse is functional but clearly not much use!
A subsequent reboot brings up the options for restarting following an unclean shutdown of windows. Running in safe mode, the restart hangs. The last dll loaded was crcdisk.
I am running an OEM version - once activated (assuming I ever get that far) - the installation will be locked to the mac... which is fine.
Googling the problem reveals some early Vista beta issues with graphics that caused a similar problem. Does Vista have an issue with the 8800GT that is fitted in my Mac?
Any help/ideas/suggestions/fixes much appreciated. Rather stumped.
I would load up XP Pro but I dont have an installer with SP2 :/Well my problem turns out to be a bad disk. I added two seagate 7200.11 750GB drives. Once which was making ominous ticking sounds. Vista took an age to install and really, I should have caught on earlier.
When I got a bunch of disk i/o errors creating a Fusion VM of XP Pro I decided to remove the disk and to try the other unit.
Vista installed very rapidly indeed and worked. Yes worked.
Hurrah! Problem solved.
Time to see about replacing that disk...
Maybe you are looking for
-
published ical. when someone views from a pc - it defaults to week view - I want it to default to month view. preferences on my mac are set to monthly view. on pc it has option to set preferences but when you try to set to monthly it only throws you
-
How do I display external monitor as sole display, rather than mirroring, with lid open?
How do I display external monitor as sole display, rather than mirroring, with lid open?
-
Somebody knows an example of chat in ajax with framework spry? some idea ?
-
Photo stroke effects in InDesign?
I'm creating an annual report in InDesign and I'm placing a photo on a page. I'd like the photo to have a ragged edge effect, like you could achieve in Illustrator with a box that has a torn edge brush stroke. However, there seems to be no brush effe
-
How do I import photos from iPhoto to Lightroom on mac book air?
Iv'e read in several forums that to do this you must go into the finder right click on iPhoto. Click show package contents. This pulls up a file named contents. All of the forums say to either look for a masters file or a original file and copy