Satellite L40 18P won't boot anymore

Hello folks,
my Satellite L40 18P won't boot anymore. All I get is the Power LED to go green. The DVD ROM drive blinks and I can open and close it - but that's it. Nothing else happens.
Any idea in the forum what I can do to get the notebook boot again ? Or please ask questions for additional details.
many thanks, Johi 13

Hi,
wow, that was fast.
No, I can't see anything - the screen stays black. I do not hear the HDD start, neither do I hear the fan.
This behavior appeard for the first time yesterday evening.
Last activity was (if I remember correctly) closing the lid and sending the notebook to standby.
So far, I haven't tested it with an external monitor.
thanks, Johi13

Similar Messages

Satellite L40-10U - Won't boot up

Hi,
my Satellite L40-10U wont boot up. I switch it on, fan, DVD-ROM, battery LED works. Hard drive LED only flashes once (If I'm lucky). The screen is blank, at sunlight I noticed it darkenes when switched on, but no further activity (I tried external, still nothing). I tried also the trick with removing the battery and pushing the power button, then plugging the charger, etc. but still nothing.
Now, I noticed that when I remove the RAMs (or try plugging just once at the time) it still does exactly the same thing, so I want to ensure if it is a problem with dead RAMs? Is there a way to check the RAMs without plugging it to another ntb (i dont have any)?

Hey,
That means your notebook uses two memory modules and you have tested both modules and it still doesnt work?!
Well this would mean the RAM modules are ok and there must be another reason for this problem. For me it sounds like a typical mainboard or CPU malfunction All other components dont cause such an error but its always useful to contact an authorized service provider and ask for an exact diagnostic. Also they can make you an offer about repair costs and then you can decide if you want to repair it or buy a new one.
Check this!!!

Re: Satellite C850 won't boot anymore - broken HDD

Hello Folks,
I bought a *Toshiba Satellite C850 - 1F2* with *+Windows 8+*.
After installing, upgrading to *+Windows 8.1+* and setting up everything, the whole machine worked pretty fine.
BUT since yesterday the laptop won't boot anymore!
When I turn it on, the HDD makes click and click and the system tries to boot from DVD, from USB, from HDD, from IPV4, from IPV6 and then it says, that there is no bootable device.
Unfortunately I wanted to make the +Windows 8 Restoration-/Rescue-DVDs+ this weekend!
Huh!!!
Well, I still have an *+original Windows-7-DVD and license+*, which would be good as well (I used it the last years).
*YET*, I cannot install *+Windows 7+*.
It says something like that, that +this system is not available for Secure Boot+.
I read about "Secure Boot".
So I pressed F2, turned the laptop on and could with this reach the BIOS.
It is a *+InsydeH20 Rev. 3.7+*.
*BUT*, when I go to "Boot Mode" I can only see, that this option is greyed and I cannot change from +UEFI Boot+ to +CSM Boot+.
Even the change of the HDD made no difference.
I put in my old HDD with Windows 7 installed (wich works in the other laptop), but the system won't boot, for it is +not suitable for Secure Boot+.
*So, WHAT NOW?*
I mean, it cannot really be the Toshiba politics, that you need to throw away your laptop, if the HDD breaks, can it?
For I didn't create the Rescue-DVD, I have just my Windows 7 DVD and another HDD with installed Windows 7.
Do I need to buy another Windows 8 licence and another HDD, to install Windows 8 (suitable for Secure Boot) again?
Would it even work like that?
Or is there any chance to upgrade the BIOS, for that I can then change from UEFI Boot to CSM Boot?
Or is there any other chance, to use my other HDD with Windows 7, or at least a new clean HDD, on wich I then can install my Windows 7 OS?
I hope, that someone can give me any good advice, what to do now ... without throwing the Toshiba laptop away ;)
Thanks in advance!

If the HDD died, in needs to be replaced.
If notebook is still covered by warranty, the HDD will be replaced free of charge. If warranty isnt valid, you will need to pay for the new HDD.
I think this understandable.
_Now some facts about the Recovery disk._
If you did not create a recovery disk in the past, you could order the recovery medium on this page: http://backupmedia.toshiba.eu/landing.aspx
The recovery disk would install the Toshiba image and would set the notebook back to the same state like at the first day of purchase.
_Regarding the Win 7 installation:_
Usually to install the non UEFI capable system, the secure boot needs to be disabled and boot mode needs to be set to CSM mode.
If this isnt possible you should update the BIOS but to do that you need an running Windows system (Win 8).

Satellite A40-231 won't boot after wrong firmware update

Hi,
i own a toshiba satellite a40-231.it won't boot anymore because i have flashed it's dvd-rw drive(sdr-6112) with the wrong firmware and i also made a big mistake making a non-bootable active dos partition,trying to flash the correct firmware.So, my question is: can i boot from usb flash disk?i believe it's the only option i have left, if not network boot.
Thanks in advance!

Hi
As far as I know its not possible to boot from any other devices as from USB FDD / HDD / CD-ROM / LAN
You could boot from network but if you want to install the OS via LAN you will need an RIS server. But its not very easy to do it without any additional experience. So I think this option is nothing for you.
It seems the drive is dead or malfunctions and therefore the best idea is to replace the device drive. I know, its hard to hear that but I dont see any other solution

Mac mini won't boot anymore

My Mac mini won't boot anymore. It's been running fine for months.
It's running Leopard Server 10.5.2 Build 9C31
It starts to boot, I get the first spinning gear with the gray screen, then the blue desktop blinks, then a second spinning gear on a gray screen and it appears to hang (the gear stops spinning).
I booted off the install DVD, ran disk utility, repaired the HD, repaired the permissions: the behavior is the same.
Safe mode doesn't work (same hang as above).
Single user mode does work.
I can connect to it via Server Admin while it appears hung.
The last few lines of the system log are:
May 15 18:38:58 server emond[67]: SetUpLogs: uid = 0 gid = 0
May 15 18:38:58 server emond[67]: SetUpLogs: opening /Library/Logs/EventMonitor/EventMonitor.error.log
May 15 18:38:59 server kextd[23]: writing kernel link data to /var/run/mach.sym
May 15 18:39:09 server KernelEventAgent[59]: tid 00000000 received unknown event (12)
May 15 18:39:20 server kernel[0]: display: Not usable
May 15 18:39:20 server com.apple.KerberosAutoConfig[126]: Kerberos configuration is up to date
May 15 18:39:20 server com.apple.ATSServer[125]: FODBCheck: New annex file created
May 15 18:39:21 server ARDAgent [130]: ******ARDAgent Launched******
May 15 18:39:21 server com.apple.KerberosAutoConfig[132]: Kerberos configuration is up to date
May 15 18:39:22 server ARDAgent [130]: call logout from LoginLogoutProxyCallBackFunction
May 15 18:39:22 server com.apple.launchd[1] (com.apple.RemoteDesktop.agent): Throttling respawn: Will start in 9 seconds
May 15 18:39:24 server loginwindow[58]: Login Window Started Security Agent
May 15 18:39:29 server servermgrd[53]: servermgr_calendar: created default calendar virtual host
May 15 18:39:31 server ARDAgent [146]: ******ARDAgent Launched******
May 15 18:39:32 server ARDAgent [146]: ******ARDAgent Ready******
May 15 18:39:33 server mdworker[109]: (Error) SyncInfo: Boot-cache avoidance timed out!
May 15 18:39:54 server Python[47]: CGImageSourceCreateWithData data parameter is nil
May 15 18:39:54 server com.apple.wikid[47]: Thu May 15 18:39:54 server.jeff.carpenter.name Python[47] <Error>: CGImageSourceCreateWithData data parameter is nil\n
May 15 18:39:56 server kernel[0]: AppleYukon2 - bad packet received. length: 1440, packet status bits: MII error
May 15 18:39:56 server kernel[0]: AppleYukon2: 00000000,00000001 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
May 15 18:49:54 server kernel[0]: serialnumberd 194 FSWRITEDATA SBF /dev/dtracehelper 13 (seatbelt)
May 15 18:49:54 server kernel[0]: serialnumberd 194 FSREADDATA SBF /dev/autofs_nowait 13 (seatbelt)
May 15 18:49:54 server kernel[0]: serialnumberd 194 FSREADDATA SBF /usr/sbin 13 (seatbelt)
May 15 18:55:12 server kernel[0]: AppleYukon2 - bad packet received. length: 23, packet status bits: MII error
Any ideas?

Yes, it's been running Server since I purchased it.
I doubt the serial number is in use elsewhere: I purchased the 10-user version at a retail store in a sealed package and I've only installed it once.

Satellite C850-1j1 does not boot anymore

my laptop Satellite C850-1j1 doesn't boot anymore.
Happened after partition changes. shows a error screen telling me the computer needs to be repaired using recoverymedia,
I've got a working hirens boot cd and usb (tested on other comp.) but the laptop is not responding
op. system win 8 64 bit brandnew.
suggestions are welcome

Hi
The message says that you have to install the system again using recovery media
As far as I know the notebook was preinstalled with the WIN 8 64BIT system.
You can use the HDD recovery option
Power on the unit and press F12.
Then choose HDD recovery option appearing in the boot menu.
Follow the instruction on the screen
Good luck!

Won't boot anymore but in safe mode

My laptop won't boot anymore. I get a gray screen with a prohibition sign. Here's what I found so far:
If I boot in the verbose mode it gets stuck on something like Looking for boot device.
I zapped the PRAM. Didn't help.
I can boot in safe mode.
I used Disk Utility to check the drive and permisions. Everything ok.
I can't boot from the original Snow Leopard DVD. I press C, the drive spins then stops.
I reinstalled Snow Leopard from the safe mode. Didn't help.
In safe mode Safari is crazy slow. Firefox runs full speed.
Any idea?

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Unless you can boot from your installer DVD there's nothing you can do to reinstall OS X, so I'm not sure how you did reinstall as you said.
Booting From An OS X Installer Disc
1. Insert OS X Installer Disc into the optical drive.
2. Restart the computer.
3. Immediately after the chime press and hold down the "C" key.
4. Release the key when the spinning gear below the dark gray Apple logo appears.
5. Wait for installer to finish loading.

Powermac G5 1.8Ghz June 2004 won't boot anymore

Hi all,
Past week i've bought a second hand PM G5. At first it seems to be all ok, but right now its not working anymore.
I've managed to install the OSX on the first evening i've had the PM G5. After installing evrything seemed to be fine. But after 30 minutes surfing on the internet, it froze. I had to give it an hard reset by holding down the power button.
After turning it of, it won't boot anymore. after a few times trying with 10 secconds between it, i unpluged the powercabel for 2 minutes. Wile turning it on after 2 minutes, it was booting , but it stopped booting after 1,5 minute and froze.. after hard resetting it, i've managed to boot it right. The OS seemed to be ok again, but after 5 till 10 minutes it froze again.
Right now it won't boot anymore... it starts (without the front light, this light only blinks fast once i turn it on, but after that no more. Sometimes it won''t even flash.
I've been buzzy replacing some components to get to know if it was a hardware fail. I've first replaced the PSU with two other PSU's from the PM G5, but won't do a thing.
The i've replaced the memory with 4 kind of difrent pairs, but won't do a thing either. At last i replaced the Logic Board, this won't even do a thing about it.
Of course i replaced the PRAM battery first, but also this won't help me.
I've tested it in AHT, but evrything was working well, according to AHT. I've managed to get the system log, but nothing scarry though here also, only some 122 errors some times. (download the system log here: http://www.mijnbestand.nl/Bestand-F4DDN66WLRCI.log )
I've reset al things possible like PRAM reset, PMU reset. Nothing seem to be working.
What can i do next to get this thing work?? I'm getting nut's here..
Please help..
Thanks a Lot
MArtijn Snoek

Hi martijnsnoek, and a warm welcome to the forums!
Can you count the beeps or flashes?
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
http://support.apple.com/kb/HT1547
So, with the info you given, two things come to mind...
Bad solder joints around the RAM slots, try heating that area with a Hair Dryer for 3 to 5 minutes, then see if it starts.
If you can get it running, Get Temperature Monitor to see if it's heat related...
http://www.macupdate.com/info.php/id/12381/temperature-monitor
And/or iStat Pro...
http://www.islayer.com/apps/istatpro/
If you have any temps in the 70°C/160°F range, that's likely it.
BTW, have you blown the dust out of it since you got it?

Won't boot anymore after nvidia-xconfig

Hey Guys,
Got a problem with my Arch Linux here, hope you can help.
Today I tried to install the official Nvidia Driver and BumbleBee following along the great Wiki on this topic.
Everything worked just fine and I also could run optirun gfxgear or somemthing like this.
I wanted to switch to the Nvidia Settings in the settings menu and it told me to configure my xconfig and restart x so I typed nvidia-xconfig in the terminal and it gave me an success output.
I restarted my system and now it hangs on the graphical thing I think. It won't boot anymore.
Hope you can help me out.
Thanks alot
Edit: My Nvidia Card is a Nvidia GT 740M if this matters
Last edited by Whitz (2015-02-09 11:02:41)

No, I have a laptop with 2 graphic cards an intel hd4000 and a nvidia gt 740m.
I ran the Arch Linux installation well until I tried to get the nvidia gt working with bumblebee.
I followed the wiki of the bumblebee topic and it worked well. I wanted to switch into the nvidia settings and it told me my x isnt configured properly and I should type nvidia-xconfig and restart X.
After the restart it won't boot to the graphical interface anymore.
Hope this cleared up the things
Also I dont get any errors but it just wont load..
Last edited by Whitz (2015-02-09 12:08:49)

Satellite A205-S5804 won't boot.

My computer Satellite A205-S5804 won't boot.
It won't run on safe mode, and it won't run the system restore.
It remains black with a cursor, if anything at all.
How do I get my computer back on?

Hi
Youve got a cursor which is flashing in the upper left corner?
In such case you should check of the HDD has been recognized by BIOS!
If the HDD is listed in BIOS then I would recommend checking the HDD using the drives fitness test:
http://www.hitachigst.com/hdd/support/download.htm
To run the drives fitness test you must download the appropriate creator or image and create a self-booting media.
Check it!

SRW248G4P switch won't boot anymore

I have a Linksys Cisco Small Business switch model SRW248G4P which won't boot anymore. This is what I see with Putty when it boots (console interface):
Image Loader 1.0.1
Loading Diagnostic Image File : SRW224G4P_SRW248G4P_boot.bix
Diagnostic 1.0.1
in
The boot file seems to be the problem.
Does anyone have a solution for this problem? Some kind of hardware reset?
Kind regards
(I know it is not officially supported anymore, but I am still looking for some help)

Hi Aleksandra,
Thank you for your reply. By pressing Crtl+u rapidly while booting I managed to get in the download/xmodem menu.
Output:
Image Loader 1.0.1
File Name                         S/Up Type Size       Create Time
$logfile_1                          0    3         64 1193046:28:15
Factory_Default_Config.cfg          0    5        354 24:01:02
SRW224G4P_SRW248G4P_boot.bix        1    1    1377600 00:01:03
SRW224G4P_SRW248G4P_image.bix       1    2    3517532 00:03:42
certificate                         0    8      18040 24:00:55
startup-config                      1    5       5596 25:40:57
startup1.cfg                        0    5       5537 24:01:14
Free Space : 2097152
[X]modem Download [D]elete File [S]et Startup File
[Q]uit
Select>
Which image should I send to the switch?
The image provided by the official support page:
http://software.cisco.com/download/type.html?mdfid=282414078&flowid=3659
(version 1.0.2 or version 1.3.1)
Or the image referred to by vasukris (Moorthy) (above) (version 1.2.3 or version 1.2.2b)
Considering the advice of Tom Watts
( https://supportforums.cisco.com/discussion/11733231/srw248g4p-loader-binary-checksum-error-runtime-loading-fail-system-halt )
"1.2.2a is 1.0.6 boot code.
1.2.2b is 1.0.1 boot code.
1.2.3.0 is 1.0.2 boot code
It looks like you're using 1.0.1 boot code so the 1.2.2b firmware should be for you."
Thank you in advance!

Btrfs: System won't boot anymore after unclean shutdown

Hi,
I have a problem with my ArchLinux (kernel 3.19.2-1-ARCH).
I have my root partition as BTRFS and no /boot partition.
After an unclean shutdown the system won't boot anymore.
GRUB loads the kernel and the kernel starts but it hangs saying: Mounted /dev/sda3 on real root.
Then, I have to start a Live CD and do:
btrfsck /dev/sda3
After that the system boots correctly.
I've tried adding fsck to the HOOKS in the mkinitcpio.conf file and in fact it tries to fsck the filesystem (but with BTRFS, fsck.btrfs doesn't work...)
What can I do?
Thanks

I'm also having this problem. I tried booting up the netinstall image to debug it, but I can't mount my btrfs volume from there either: mount just hangs. After a while, the kernel goes:
[...] INFO: task mount:612 blocked for more than 120 seconds.
[...] Not tainted 3.19.2-1-ARCH #1
[...] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[...] INFO: task btrfs-transacti:636 blocked for more than 120 seconds.
[...] Not tainted 3.19.2-1-ARCH #1
[...] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
From this post I guessed that I might just need to wait so that I could defrag the volume once it was mounted, but it's been hanging for over 15min now (the message above continues to come up periodically).
Like the OP in the thread I linked to above, my btrfs volume is inside an LVM volume (which is on dm-crypt). Don't know whether that's relevant.
Output of btrfs-check:
Checking filesystem on /dev/pixie/btrfs
UUID: e04cc661-e31a-4dbf-870d-664bc913e34a
found 76855677062 bytes used err is 1
total csum bytes: 72928436
total tree bytes: 2092515328
total fs tree bytes: 1888452608
total extent tree bytes: 104644608
btree space waste bytes: 357251032
file data blocks allocated: 181197139968
referenced 109440282624
btrfs-progs v3.19
dmesg output:
[ 36.824998] Btrfs loaded
[ 36.826713] BTRFS: device fsid e04cc661-e31a-4dbf-870d-664bc913e34a devid 1 transid 98618 /dev/dm-3
[ 46.219014] BTRFS info (device dm-3): disk space caching is enabled
[ 46.259830] BTRFS: detected SSD devices, enabling SSD mode
[ 240.333313] INFO: task mount:539 blocked for more than 120 seconds.
[ 240.335542] Not tainted 3.19.2-1-ARCH #1
[ 240.337795] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.340263] mount D ffff8800cf2837f8 0 539 453 0x00000000
[ 240.340277] ffff8800cf2837f8 ffff8800cf2331b0 0000000000013f00 ffff8800cf283fd8
[ 240.340286] 0000000000013f00 ffffffff81818540 ffff8800cf2331b0 ffff8802094f67a8
[ 240.340291] 0000000000000004 ffff8800cf283758 ffffffffa0a2fc91 ffff8802094f67a8
[ 240.340298] Call Trace:
[ 240.340335] [<ffffffffa0a2fc91>] ? set_extent_buffer_dirty+0x71/0xc0 [btrfs]
[ 240.340357] [<ffffffffa0a05796>] ? btrfs_buffer_uptodate+0x56/0x80 [btrfs]
[ 240.340366] [<ffffffff8155e999>] schedule+0x29/0x70
[ 240.340389] [<ffffffffa0a47745>] btrfs_tree_lock+0x65/0x200 [btrfs]
[ 240.340396] [<ffffffff810b4380>] ? wait_woken+0x90/0x90
[ 240.340410] [<ffffffffa09e5cd9>] btrfs_search_slot+0x799/0xaa0 [btrfs]
[ 240.340425] [<ffffffffa09e79f5>] btrfs_insert_empty_items+0x75/0xd0 [btrfs]
[ 240.340446] [<ffffffffa0a47a37>] btrfs_insert_orphan_item+0x67/0xa0 [btrfs]
[ 240.340465] [<ffffffffa0a4a12e>] insert_orphan_item+0x5e/0x90 [btrfs]
[ 240.340482] [<ffffffffa0a4c531>] replay_one_buffer+0x361/0x380 [btrfs]
[ 240.340504] [<ffffffffa0a2f244>] ? alloc_extent_buffer+0x34/0x370 [btrfs]
[ 240.340523] [<ffffffffa0a488f3>] walk_down_log_tree+0x1d3/0x410 [btrfs]
[ 240.340540] [<ffffffffa0a48bfb>] walk_log_tree+0xcb/0x1d0 [btrfs]
[ 240.340558] [<ffffffffa0a507f7>] btrfs_recover_log_trees+0x1e7/0x490 [btrfs]
[ 240.340575] [<ffffffffa0a4c1d0>] ? replay_one_dir_item+0xf0/0xf0 [btrfs]
[ 240.340596] [<ffffffffa0a08b3e>] open_ctree+0x17ae/0x2030 [btrfs]
[ 240.340609] [<ffffffffa09dd633>] btrfs_mount+0x843/0x920 [btrfs]
[ 240.340618] [<ffffffff8117b7aa>] ? pcpu_alloc+0x35a/0x680
[ 240.340628] [<ffffffff811d5d68>] mount_fs+0x38/0x1c0
[ 240.340634] [<ffffffff8117bb05>] ? __alloc_percpu+0x15/0x20
[ 240.340641] [<ffffffff811f116b>] vfs_kern_mount+0x6b/0x120
[ 240.340647] [<ffffffff811f4184>] do_mount+0x224/0xb40
[ 240.340653] [<ffffffff811f4dae>] SyS_mount+0x7e/0xe0
[ 240.340661] [<ffffffff81562809>] system_call_fastpath+0x12/0x17
[ 240.340671] INFO: task btrfs-transacti:561 blocked for more than 120 seconds.
[ 240.342927] Not tainted 3.19.2-1-ARCH #1
[ 240.345175] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.348473] btrfs-transacti D ffff88020b88bd98 0 561 2 0x00000000
[ 240.348483] ffff88020b88bd98 ffff880211edc590 0000000000013f00 ffff88020b88bfd8
[ 240.348491] 0000000000013f00 ffff8802162289f0 ffff880211edc590 ffff8802094a70c8
[ 240.348496] ffff8802094d8000 ffff880200000000 ffff8802094d8000 ffff880200000033
[ 240.348501] Call Trace:
[ 240.348511] [<ffffffff811b5d1a>] ? kmem_cache_alloc+0x16a/0x180
[ 240.348525] [<ffffffffa09e07ca>] ? btrfs_free_path+0x2a/0x40 [btrfs]
[ 240.348543] [<ffffffffa0a64213>] ? __btrfs_run_delayed_items+0xf3/0x1d0 [btrfs]
[ 240.348550] [<ffffffff8155e999>] schedule+0x29/0x70
[ 240.348568] [<ffffffffa0a0b555>] btrfs_commit_transaction+0x2a5/0xbe0 [btrfs]
[ 240.348573] [<ffffffff810b4380>] ? wait_woken+0x90/0x90
[ 240.348590] [<ffffffffa0a06fc5>] transaction_kthread+0x1d5/0x240 [btrfs]
[ 240.348605] [<ffffffffa0a06df0>] ? btrfs_cleanup_transaction+0x5a0/0x5a0 [btrfs]
[ 240.348611] [<ffffffff81091748>] kthread+0xd8/0xf0
[ 240.348617] [<ffffffff81091670>] ? kthread_create_on_node+0x1c0/0x1c0
[ 240.348624] [<ffffffff81562758>] ret_from_fork+0x58/0x90
[ 240.348629] [<ffffffff81091670>] ? kthread_create_on_node+0x1c0/0x1c0
Last edited by ouroboros8 (2015-04-02 12:37:25)

Satellite A300-1BZ Won't Boot!!!

My laptop won't boot anymore. The Toshiba sign pops up for a few seconds then the screen goes blank. I have tried F8 but nothing happens. Any ideas???
Thanks

Hi
I found this thread and I would like to summery you issue;
- You are not able to start the Windows OS; neither using the normal nor safe mode.
- you are not able to boot from any bootable disks like recovery disk or other windows disk
- you cannot recovery the notebook using the HDD image
- You can see nothing on the screen, its black.
- connecting external monitor does not help
Unfortunately buddy, but it looks like a hardware malfunction something is wrong maybe the motherboard who knows
I think the A300 should be covered by warranty therefore I would strongly recommend contacting the ASP in your country and to ask for the help!!!

Satellite L40-139 won't start

?02-19-2014 06:41 PM - edited ?02-19-2014 06:45 PM
Hello, i have a problem with SATELLITE L40-139
the thing is when i press power button, hard drive diode starts to flash, diode on cd-rom is lighted and the screen is black. I noticed that electornics in the CD-ROM makes a sound tick in the same way the hdd diode flashes (when it flashes i hear a tick form cd-rom, yes i unfolded whole notebook).
I can only say that i connected HDD to my PC and it's working., well fan isn;t working too but i think it will start, after some time (like always it did)
Now lets say about notebook crash circumstances: That was a year ago, it fell from 1 inch (such height ;]) i saw that ribbon cable that was connecting touchpad to the mohterboard was broken, and my computer diidn't start, i thought theres a problem, but i forgot about it and left the notebook for over 9 months (with disassebled hdd, cd-rom and battery) then i decided to try to switch it on.
And viola! it works it boots etc.
So after a month of being happy i got drunk that i couldn't sit on chair and i decided to lie with my laptop on bed, i just lied down and put notebook on my stomach and it crashed (freezed screen) i decided to reboot it, but it won't start.
Heres a video with what i get during powering it up: [http://www.youtube.com/watch?v=jC0pGBBVwJk] (not luckily my phone fell into mud and lags when i record videos)
Some people suggested that i should connect external display to see if theres any image, but the result is still the same. (Screen does not even power on)
Maybe someone could help me fix it without sending it to customer service.
Cheers.

Hi
>So after a month of being happy i got drunk that i couldn't sit on chair and i decided to lie with my laptop on bed, i just lied down and put notebook on my stomach and it crashed (freezed screen) i decided to reboot it, but it won't start.
I think the notebook overheated or something like that
Maybe its just an RAM problem and therefore it would be useful to test the unit in connection with new, tested RAM modules but this is only an idea
As Dr.Lamp already said, in worst case it might be a motherboard problem and this would mean that notebook fix would be a costly affair.

Satellite Pro 6000 doesn't boot anymore

Hi all,
I have a Satellite Pro 6000 that is quite old, but until yesterday it was working fine. Today, it won't start anymore. The indicator LEDs are on (220v:green/power:green/battery:orange) but the BIOS or OS won't start. Fan doesn't work either. The FN key seems to work - if I press it, the indicator below F11 lights up. If I press and hold the power button the power indicator LED goes off.
I've removed the battery to see if that might help, but it basically gives the save (non)result.
Is there any way to do a hard reset? Or is it curtains for this laptop?
Like to hear your thoughts on this one.
JP

Hi
Try to disconnect the AC adaptor and remove the battery a leave the notebook for a while. Wait about 20-30 min, connect all parts again and try to boot up.
If it will not work I assume the notebook hardware malfunctions Maybe its a motherboard fault (power supply electronic) or CPU.
Who knows. Without any hardware tests its not easy to find out what device malfunctions

Satellite L40 18P won't boot anymore

Similar Messages

Maybe you are looking for