Satellite L650-1P4 - AC power supply is not working
I have a problem with my computer:
When I plug in the AC adapter to the computer, the computer did not work and the battery is no longer supported but computer works with battery and the charger works on another pc.
+Message was edited: posting has been translated+
I have a problem with my computer:
When I plug in the AC adapter to the computer, the computer did not work and the battery is no longer supported but computer works with battery and the charger works on another pc.
Similar Messages
-
My MagSafe Charger / Power Supply is not working
I am using mid 2009 13" MacBook Pro with 85W MagSafe . My operating system is Lion 10.7.4.
I heard a "click" coming from the direction of where my charger and just before and now its not working.
The light is not coming on the charger itself
No power is shown be coming into the computer on the Desktop toolbar either, nor does my computer that there's a charger plugged in.
I have tried the charger in a number of the different sockets around the apartment and still no joy
The transformer "block" is cold
Could this be a s simple as a blown fuse in the plug or something else altogether?
I need to fix this asap. No power = no computer. All help much appreciated.I've copy and paste info from under AC. The MagSafe charger is physically connected, the report says that is not connected and not charging.
Any tips on where I can get cheap new Apple charger (60W MagSafe)? Thanks to you
both.
Battery Information:
Model Information:
Serial Number: 9G9460Q108VNC
Manufacturer: DP
Device Name: bq20z451
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 3
Hardware Revision: 2
Cell Revision: 100
Charge Information:
Charge Remaining (mAh): 1669
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 4936
Health Information:
Cycle Count: 507
Condition: Normal
Battery Installed: Yes
Amperage (mA): -2244
Voltage (mV): 10881
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 180
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 15
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: Yes
Display Sleep Uses Dim: Yes
PrioritizeNetworkReachabilityOverSleep: 0
RestartAfterKernelPanic: 157680000
Battery Power:
System Sleep Timer (Minutes): 15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 3
Wake on AC Change: No
Wake on Clamshell Open: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: No
RestartAfterKernelPanic: 157680000
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: No
Charging: No -
Power Supply is not working in Germany
Hi, I bought long time ago a notebook in USA. When I was back in Germany the notebook didn't charged any more. I asked for support, because of the guarantee, but they said there guarantee is for supplies only six month. I forgot the notebook in the cellar. Now I'm asking myself, if the is a possibility to get a "new" notebook running. I just used the notebook 2 hours. Thanks and regardsMosesKama P.S: I wouldn't recommend the service in Germany to somebody. I wrote them before months and I'm still waiting for a feedback.
MosesKama wrote:
Do you know about any possiblities to get run a notebook that a bought in the Staates, but like to use ist in Germany.The notebook is not charging. ThanksDid you check with HP support if the chargers are of different voltages standards which may require different chargers? -
Satellite L650-116 memory card reader is not working
Hello
I have a problem with built-in memory card reader. Do not read my SD card at all, drivers installed.
Please help.Hi
The notebook supports an BRIDGE MEDIA SLOT which support this card formats;
SD Card 8MB-2GB
SD-HC 4GB-32GB
Memory Stick 128MB-256MB
Memory Stick Pro 256MB-16GB
mini SD 32MB-2GB
SDXC 64GB
As you can see, the notebook is able to read max 2GB SD card.
The card reader will not read bigger SD cards. -
Satellite A660-11M on Windows 7 - Toshiba Power Saver does not work
I have a Satellite A660-11M and I work on Windows 7 Ultimate
The problem is that I have download all drivers and updates but the toshiba power saver does not work its installed with no error and TPSLaunch (green icon) does not open when I click on it and no icon I found in the control panel for the program afterIi install all the Value Added Package!Toshiba Power Saver is only for XP installations, you can't install the XP Drivers (and most Vista Drivers) in Windows 7.
Make sure all your drivers are for the A660, and make sure they are for Windows 7. -
Hi all,
my customer has a lot of WS-C2960XR-24PS-I (15.0(2)EX4) 24 and 48 Port switches, some are in a stacks, others not. All have 2 Powersupplies.(each 640 Watt)
Now he notice this message every 5 minutes, but not on all switches.
Looking at the switch, the PS seems to be ok.
There is a known issue, but this one only mention the problem during insertion, not during normal runningtime.
What can be the problem here?
Thanks
Willem
Additional Information:
CustomerSwitch#
Nov 27 09:28:44.622 CEST: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding
CustomerSwitch#
Nov 27 09:33:44.642 CEST: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding
CustomerSwitch#
CustomerSwitch#
CustomerSwitch#sh env all
FAN PS-1 is OK
FAN PS-2 is OK
SYSTEM TEMPERATURE is OK
System Temperature Value: 41 Degree Celsius
System Temperature State: GREEN
Yellow Threshold : 67 Degree Celsius
Red Threshold : 75 Degree Celsius
POWER SUPPLY 1A TEMPERATURE: OK
POWER SUPPLY 1B TEMPERATURE: OK
SW PID Serial# Status Sys Pwr PoE Pwr Watts
1A PWR-C2-640WAC DCB1728B1K2 OK Good Good 250/390
1B PWR-C2-640WAC DCB1738B2A1 OK Good Good 250/390
CustomerSwitch#
--- ende -------
Release Notes for Catalyst 2960-X and 2960-XR Series Switches, Cisco IOS Release 15.0(2)EX5
---SNIP---
CSCuh65397
During the insertion or removal of a power supply, the following message might be displayed on the console:
%PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding
There is no functional impact. There is no workaround.
---SNIP---Hi ,
As per the Bug note, (see the Further Problem Description:)
Workaround:
NA
Further Problem Description:
If this log is repeated even after OIR, It should be different issue. It has to be debugged separately
Thanks,
VS.Suresh -
Satellite A660-11M - Power Saver does not work
I have a Satellite A660-11M and I work on Windows 7 Ultimate
The problem is that I have download all drivers and updates but the toshiba power saver does not work its installed with no error and TPSLaunch (green icon) does not open when I click on it and no icon I found in the control panel for the program afterIi install all the Value Added Package!Hi buddy,
Wait a moment, please.
Im a little bit confused about your posting First you write about Power Saver and then about green icon Which one you mean exactly and whats the problem?
If you mean Eco mode you have to install Eco Utility from official Toshiba website. -
I am having MacBook Pro 3 yrs old and today while I was watching some movie on it suddenly it got power off and when I am trying to start it, it's power button is not working even the round button on external left side is not showing battery lights. But when I connect it to chrger then Charger only gives green light and even the external round button only shown 4 green lights (if charger connected). I don't know what to do now
Sounds like you need a #1SMC Reset
1. SMC reset
>>Instructions to reset SMC
Disconnect other non-Apple and external hardware except (if applicable) a mouse and keyboard until your finished repairing your machine.
Problems solved: Fans blowing with no activity, machine is not booting, power button pressed and nothing happens, problems with indicators, Magsafe has wrong lights, battery is not charging, monitor and graphics issues etc. If the battery is not charged (from like letting it sleep too long), let the Mac charge up awhile afterwards.
Will not hurt the machine resetting if it's not broken.
Other related hardware problems (optional):
Check battery status: Hold option/alt key down while clicking on the battery icon in the menu bar, top right corner.
Magsafe: Use the correct/matching power supply charger with your Mac, not a less powered one from another Mac.
Apple: Laptop won't power up Apple: Computer won't power up Troubleshooting optical drive
Magsafe problems Magsafe problems more -
Dead B&W G3 ? Only the power supply seems to work...
Hi Everyone...
Here's my setup:
Powermac G3 B&W Rev.B
Processor: Powerlogix G3 750FX (1Ghz)
Ram: 1GB (4x256Mb)
OS 10.4.9 (latest OS supported by Powerlogix)
HD: IBM desktar 120MB
DVD-Rom: Samsung DVD-/+R
PCI 66Mhz -> Radeon 9200
PCI 33MHZ -> M-Audio 2496 Audiophile Audio Card
PCI 33MHZ -> Sonnet Tango 2.0 (USB/FW)
PCI 33MHZ -> Sonnet Tempo ATA133 (my main drive uses this card)
The B&W G3 has been one of my hobby machine for a year (I mostly use it as a jukebox to listen to AIFF disc images in PCM / uncompressed sound).
Anyway... it died on Saturday night... just after upgrading to a Sonnet Tempo ATA 133 card...
As I've been a Mac user for a long time (and I've been there before with a Gossamer MB in my beige G3 which died out of the blue once), I completely did empty the motherboard... adding one element at a time to isolate the issue but the fact is that:
a) no startup sound
b) black screen (nothing comes out of the Radeon 9200)
c) only the power supply seems to work
d) even when plugging the HD into the MB IDE socket, the HD doesn't even activate itself (no boot).
Of course, I went through the CUDA switch, tried to reset the PRAM, checked the jumpers on the HD (master position)...
I also tried to boot the system off the OSX Tiger Install DVD but nothing...
I have a feeling that my MB may be DOA.
What do you think ?
If this is the case, since I'm using a Tempo ATA 133 PCI Card, does it make any difference to replace it with either a REV.A or B MB ?
Thanks for your help,
Pierre André.
Message was edited by: pierreandre90403Hi Grant,
I posted the following on another thread, but I haven't gotten any response.
I'm having a similar problem with a B&W 350 MHz (rev 1 I think). I get the start up tone and nothing appears on the monitor. Not sure if the machine is actually booting or not.
I am trying to repair this machine for a friend. They had been having a problem with the machine booting into a blue screen. I suspected a corrupt directory, so I ran Disk Utility (from another machine) and also Disk Warrior. Both Disk Utility's Disk Repair feature and Disk Warrior found problems. Disk Warrior was able to successfully rebuild the directory.
I had removed the hard drive from the machine and put it in an external casing in order to run Disk Repair and Disk Warrior. Upon putting the hard drive back into the B&W and booting the machine, I was able to successfully boot the machine into Tiger. I tested the machine for a few minutes and it seemed to work fine.
Next, I ran software update and installed a new version of Safari and then after the required re-boot, tried to repair disk permissions. During the repair of disk permissions, the machine froze up completely. The clock stopped ticking and there was no mouse or keyboard response. I tried using the re-boot button on the front of the machine, but the machine would not fully re-boot. I get a boot tone, but no video.
I tried re-setting the CUDA chip by pressing the re-set button on the logic board, but to no avail.
Finally, I did take the battery out and had it tested at Radio Shack. The battery is showing a good 3.6 volts.
I have a second B&W (300 MHz) that is basically doing the same thing. Do you know what could be causing the lack of video signal?
Cheers,
Thomas
PS: I tried re-setting the logic board as described in another post (unplugged machine, pressed power button, removed battery, waited 10 minutes). I have tried the CUDA reset several times, but I only press the button for a second, not 15 seconds. I have re-seated the RAM. I have removed all the RAM and tested each. Nothing seems to work. -
T440p Fingerprin​t power-on is not working
Hi , i just recieved my new T440p , Fingerprint @ power-on is not working although all config. is done typically in lenovo fingerprint manager pro & fingerprint security settings in the BIOS , i start my laptop it goes through windows normal startup & logon without any request for fingerprint .
Solved!
Go to Solution.Dear Ahmad
Welcome in lenovo community
Have you tried to first to enroll your fingers first , an application called Lenovo Think Vantage should be installed .
Do you have this application installed ?
Also you need to check the device manager , it's better to send us a screen shot of it .
Let us know
Thanks
Alaa
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter! -
Froze on black screen and power button does not work
my sons ipod touch is stuck on a black screen when plugged into the computer got a spinning wheel and will not connect now spinning wheel will not go away the power button does not work so can not reset it manually
any suggestions would be appreciated- iOS: Not responding or does not turn on
Neglect the reset and when it says place the iPod in recovery mode use one of thes programs
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Is there anyway to power off an I-phone 4s if the power button is not working?
Is there anyway to power off the phone if the power button is not working?
Assistive Touch. Tap Settings App > General > Accessibility > Assistive Touch > ON > at bottom of screen tap button > Device > press and hold Lock Screen icon > when slide to power off appears > slide it. To turn iPhone ON connect to Power Source with USB cable, charger or USB port of computer.
All iPhone 4S have full Warranty Coverage. Make Genius Reservation and take iPhone to Apple for resolution. -
I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4
I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4
-
Hi my keyboard is not working I took off the bottom case to change it prior my keyboard was fine and after just the power key worked. I checked everything no portions were bent and it plugged in good. I tried to turn it on this morning and now the power key doors not work??
Back up all data.
Triple-click anywhere in the line below to select it:
pmset -g assertions
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
Post any lines of output that appear below what you entered — the text, please, not a screenshot. -
My ipad has a black screen and the power button is not working. Help!
This is the second time my ipad screen has gone black. The power button is not working. I reset the ipad about two weeks ago when this happened. However, this time I am not able to get itunes to recognize the device. It keeps asking to respond from the ipad (obviously with a black screen that isn't going to happen). Im not sure what to try next...thoughts?
Have you tried to give it a reset?
Reset
Hold down the sleep and home keys for about 20 seconds. When you see the silver apple, let go and let it reboot. No data will be lost.
Maybe you are looking for
-
I am having three problems with Adobe Flash and would like some assistance in resolving them. 1) Problem number ONE: Several months ago installing an antivirus program broke my Internet Explorer. All attempts to fix or upgrade IE have failed. Not
-
I used the liveupdate 3 to update my vga bios and when it rebooted the computer the videocard wont work now. I flipped the twinbios to the safe mode but nothing happened. When i put my old card in it works fine. Any suggestions?
-
Fcpx import of a raw image is advertised to work in its help databases, but it actually doesnt work. I tested the most known and now industry standard Raw format, which is the Adobe DNG raw format, and FCPX ignores the embedded jpg preview . i tried
-
16x16 png image looks blurry in flash mx at an integer x y position
I have few small png images (16x16 px) when I place them on stage it shoudl look best when placed at an integer x and y position. e.g. x=100 and y=50 But in MX it only looks clear when placed at an integer with .8. e.g x=100.8 and y=50.8. In MX 2004
-
I have Adobe photoshop Elements 11. My question is when I want to print a picture i get a pop-up stating ( The application is unable to intialize the printer settings) I love the software, but I need to be able to print my pictures. Please help me!!