Satellite L655D won't start anymore

So I spilled ramen soup onto my cousin's laptop (so stupid...) on the body below the keyboard...
She took it home to clean it some but I guess she did a poor job because it started for a few hours and then the next day, it refused to start...
I kind of opened the laptop and I saw the motherboard and saw how this plastic covering on it has become deformed. Is this fixable?
Or will a new laptop be necessary...
Here is a picture of what I saw. Thank you!
http://i39.tinypic.com/hskkdu.jpg

the image from the link isn't to good because from the angle you took the picture it looks like a lot of dust.... but if that realy is deformed plastic it's a little bit strange because usualy when you spill liquid on electrical apliances you get smoke and the get black or burn with a flame from the short circuit that you give them.... and if the mother board is in deed short circuited reparing it will cost you as much as a brand new laptop....
i would like (if posible) another image with a close up of the mother board in order for someone to get an idea of what you have there dust or a chard mother board... but if we think a little about it you spilled your soup but still it worked for several hours that means that your soup is inocent and the problem is somewher else i suggest visiting toshiba service for a clarification

Similar Messages

Satellite A100 - Won't start up Windows

Without changing anything, my Satellite A100 won't start up Windows.
A screen with with Windows foutherstel (failure recovery) gives two options; start windows normally and start up recovery. When I push the first option, there is a quick blue screen, what disapears too fast to read the tekst. Finally the screen failure recovery comes back. in the other option there is a screen Options for system recovery who's said; Can not start the installated program. Click on Ok to shut down the computer.
How do I fix this problem?

Hi hans_3,
Maybe something has muddled up the Windows registry or some important system files and so you cant start Windows anymore or start the system repair option.
I think in this case its necessary to reinstall Windows. Therefore you can take the Toshiba recovery disk that brings your computer back o factor settings where all drivers and tools are already installed but it wipes the whole HDD.
It takes only few minutes and needs some clicks.
Good luck! :)

Satellite L500D won't start

Hello,
My Toshiba Satellite L500D won't start.
When I start my laptop the three lights on the left light green, the two on the left are not green or red. I hear the coolingfan, no beeps at the startup. When I start the laptop with a systemdisk it's the same, nothing happens.
I contact the supportdesk and they said that it could be the harddisk, this sounds a bit strange to me because I can't start it with a systemdisk.
I hope someone can point me in the right direction
Buddy

Hello,
The notebook is my dauther's and I'm pretty sure she hasn't update the bios. She is 14 years old and she does what 14 year old girls do with their notebook. Gaming, hives, chatting etc.
What she told me is that she had some problems when starting the notebook. It didn't start correctly, she had to push the powerbutton several times, sometimes maybe like for half an hour or so, then suddenly the pc woke up and did start. SInce a few days nothing works anymore.
The screen stays black and I hear no beeps, just the coolingfan and sometimes a noice asif the hd was trying to start. The coolingfan also doesn't run properly, it makes a sound like an automobile that runs irregular
Buddy

X11 won't start anymore!

Hello,
this is a desperate call: I am at a conference with my MBP, (10.6.7, all updates done). I need Matlab for my presentation, which needs X11.
X11 (and XQuartz) decided that they won't start anymore: the icon bounces in the dock for a while, then sits there without the little light underneath, and X11 is "non responding".
The logs show something like this.
I have googled and searched: similar problems once in a while appear but no posted solution.
I tried:
1) reinstalling XQuartz (I would reinstall X11, but how? I do not have the disks with me, I am away!)
2) from an admin account
3) create a new account.
4) repair permissions.
5) reinstall the font update from Apple that was recently issued.
HELP PLEASE!!!
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: DISPLAY ("/tmp/launch-bHvQen/org.macosforge.xquartz:0") does not match our id ("org.x"), unsetting.
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: main(): argc=2
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[0] = /Applications/Utilities/X11.app/Contents/MacOS/X11.bin
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[1] = -psn_0_278596
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     Waiting for startup parameters via Mach IPC.
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: Could not connect to server (DISPLAY is not set). Starting X server.
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     X11.app: Launching /usr/X11/bin/startx:
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[0] = /bin/sh
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[1] = -c
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]      argv[2] = /usr/X11/bin/startx
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     font_cache: Scanning user font directories to generate X11 font caches
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     font_cache: Updating FC cache
11-05-16 5:02:01 PM     org.x.privileged_startx[20781]     font_cache: Scanning system font directories to generate X11 font caches
11-05-16 5:02:01 PM     defaults[20791]
The domain/default pair of (org.x.X11, dpi) does not exist
11-05-16 5:02:01 PM     [0x0-0x44044].org.x.X11[20759]     Couldn't create cookie
11-05-16 5:02:02 PM     org.x.privileged_startx[20781]     font_cache: Updating FC cache
11-05-16 5:02:04 PM     [0x0-0x44044].org.x.X11[20759]     font_cache: Done
11-05-16 5:02:04 PM     org.x.privileged_startx[20781]     font_cache: Done

Here is the solution: there was nothing wrong with x11 per se!
The problem was that about 30 files in /usr/bin (like gzip, egrep, hexdump etc) had been hosed (they had 0 file size). The puzzling messages was due to the fact that startx uses hexdump, which was simply silently doing nothing (since it had 0 size!).
I do not know what or when these files were zeroed: I suspect a recent OSX update which did not complete and I had to forcefully reboot.
I have fixed it enough to work (copying those files from another mac), but who knows what else lurks beneath the surface of apparent serenity!
I am actually surprised that the whole system did not stop functioning completely.
MORALE: if something looks strange in the logs with x11 or other apps, check the file sizes in your /usr/bin, you may be surprised too!

Adobe bridge won't start anymore. Icon is hopping and then it shuts down..

Could someone help me with this. After trying to install output module in bridge cc, bridge won't start anymore. The icon is hopping for a few seconds and then the appllication is shut down.

Oh ok - Thankyou for that. I will be ringing them tomorrow and I will not be happy ! And I'm hoping they can suggest what I'm suppose to do about getting it back to them as I can't take it in myself. SO so angry!!! Does people getting it back in a worse state happen often? :| do read these discussion boards? I hope they do!!!

Mega Player 538 won't start anymore

I just flashed the firmware of my mega player 538 to the latest 1.11.03.
The prosedure went ok but now the player won't start anymore.
When I press "Power On" -button nothing happens.
Is there anything that I can do or is the player gone...?
Can I reset the player to solve the problem?

I contacted MSI support, but no answer from them yet.
Unfortunately I didn't have time to wait because I had a very important affair where I needed the device.
So, I returned the player to the shop. Of course the shop didn't have replacement on the stock but they gave me my money back. So, I went to another shop and bought a creative player instead and I was able to complete my affair.
It would have been nice to have the problem solved because the player was perfect for my needs and was very cheap as well (only 20 euros). The new player was three times more expensive and only 512Mb storage.
If MSI will return with a solution I can post it here in case somebody else has a same kind of a problem.

My 3Gs won't start anymore, how can I get it to?

I plugged in my 3Gs for the night last week and I woke up with the battery at 80%, so I just thought that maybe it came unplugged or something. I plugged in my charger and nothing happened, I got the "Charging is not supported with this accessory" error, even though I was using the white wire that came with it. I took it out of the wall adapter and tried it on my computer, nothing. I try my brothers wire, my mom's wire, car chargers, everything. Now I'm not sure if my battery is just done, or if my phone just won't start anymore, it's out of warranty so I'm up for any type of fixes, thanks.

Clean the iPhone dock port with a clean dry toothbrush. See if it helped. If not, clean dock port very carefully with lint free cloth moistened with Isopropyll Alcohol, especially clean the pins which are on top of the dock mid rib. You can even use the toothbrush with a bit of Isopropyll Alcohol here too. Let it dry, usually 30 seconds time. See if this helped.

Ultra 10 won't start anymore

Hello,
I have an Ultra 10 box with an extra video card inside. Everything was working fine, and then I got curious and decided to open it up to see what's inside. Now it won't start anymore. I turn the computer on, the fans start spinning, but nothing gets displayed on screen. I can hear the hard disk turning too, and the CD drive is powered, but I don't think anything is going on.
The only thing I touched when I opened it was the extra graphics card, but I was very careful and I am pretty sure I did not fry it. I get nothing displayed on screen when I plug the monitor in the original video card either.
Is there anything I can do to find out what the problem is? Is there some special switch inside the box that I may have turned off without noticing?
Thanks for the help...

Hello,
when you removed the ATI Radeon (XVR-100) and powered-on, the long card (Creator3D or Elite3D) with the weird connector (13W3) became the default output device. It takes precedence over the integrated video.
Remove the long card (if you don't own a 13W3-HD15 adapter or monitor with 13W3 connector) and insert the XVR-100 (attach the monitor to the integrated video). If you power-on the integrated video becomes the default. You should see the output on the monitor.
Enter show-displays at the ok-prompt. If only a single entry is displayed, power-down and check if the card is properly seated.
Otherwise press the letter of the entry that doesn't contain /pci@1f,0/pci@1,1/SUNW,m64B@2.
This a sample output of an Ultra 10 with Creator3D as add-in board.
ok show-displays
a) /SUNW,ffb@1e,0
b) /pci@1f,0/pci@1,1/SUNW,m64B@2
q) NO SELECTION
Enter Selection, q to quit: b
/pci@1f,0/pci@1,1/SUNW,m64B@2 has been selected.
Type ^Y ( Control-Y ) to insert it in the command line.
e.g. ok nvalias mydev ^Y
for creating devalias mydev for
/pci@1f,0/pci@1,1/SUNW,m64B@2
nvalias mydev ^Y
The above sets the output-device to the integrated video even if a Creator3D is installed.
Then enter setenv output-device mydev (if you used this name) and reset-all. Attach the monitor to the XVR-100.
Michael

CVI program won't start anymore

Our measurement application worked well on several PC's (Win7 32Bit, WinXp 32Bit).
But on 2 newer PC's (Win7 32Bit) the application won't start anymore.
The attached Error with the code R6030 shows up.
We found a workaround for the problem: run the application as administrator.
But after we installed a USB-driver, this workaround doesn't help anymore,
and the Error shows up every time.
We installed the environment (cvi-rt, etc...) with an distributed setup.
So the Versions of the components are the same on every PC.
Any ideas?
Solved!
Go to Solution.
Attachments:
Untitled2.png ‏25 KB

Okay we solved the problem,
the cause was, the HP-Software, which was preinstalled on the PC's (the others were Dells)
After uninstalling the HP Security Suite our application works perfect.
I hope this helps other poor guys

NSM3 service won't start anymore

Hi,
NSM AD 3.0.4 on W2008R2
has been running fine for months, now engine service won't start anymore.
engine.log from todays start:
01 2012-12-13 11:19:19 7200 1 0001 1452 1480 ML: Failed to initialize 1
or more components and/or subsystems. Engine is switching to
stop-pending state.
ideas?
sk

Sami,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/

Eclipse IDE won't start anymore after most recent security update

Hello everybody,
after today's security update the Eclipse IDE won't start anymore on my system, I just receive the following error message:
A Java Runtime Environment (JRE) or Java Development Kit (JDK) must be available in order to run Eclipse.
No Java virtual machine was found after searching the following locations: /Applications/eclipse/Eclipse.app/Contents/MacOS/jre/bin/
java
'java' in your current PATH
Java is installed and Eclipse ran smoothly until I upgraded. Other Java programs like Visual Paradigm still work without problems.
Does anybody have an idea what I can do about this? I have already tried repairing permissions, to no avail.
Best regards,
Björn
Mac Pro Mac OS X (10.4.9)

I have narrowed down the problem even more:
Obviously system path variables are not set anymore on my system for UNIX processes that are started in background, whereas starting applications from terminal using the open command ('open Gimp.app' for instance) still works without any problems.
Any ideas where to change this behaviour?

Facebook messenger won't start anymore.

Facebook messenger won't start anymore on my iPad Air (iOS 8.1.3) after updating de Facebook App (v 23.0) on January 30. The blue circle keeps turning. What can I do?

Hi jneelen,
That is a bummer when the apps are not working. For most issues with apps that have been downloaded from the App Store, the troubleshooting article will work for most issues when they do not launch or crash on you.
If an app you installed unexpectedly quits, stops responding, or won’t open
http://support.apple.com/en-us/HT201398
Take it easy,
-Norm G.

Creeated new account - but safari won't start anymore

I created a new account with a parental control. Logged in under the new account and Safari won't start anymore. It quits directly after starting. Any help suggestion ?
Thanks much

Does it work in your old account?
If so, delete everything in the folder /Users/controlled account name/Library/InputManagers.
Also try deleting /Users/controlled account name/Library/Preferences/com.apple.safari.plist.
(replace controlled account name with the name of the controlled account)
Good luck!

My ibook g4 won't start anymor from the harddisk. so I tried to reinstall the system from the orginial system cd. Doesn't work. It says the system cd is damaged. What should I do?

my ibook g4 won't start anymor from the harddisk. so I tried to reinstall the system from the orginial system cd. Doesn't work. It says the system cd is damaged. What should I do?

I would question that error message if the Mac OS X 10.5 DVD doesn't work, either.
What error message(s) did you get with the Mac OS X 10.5 DVD? Is the Mac OS X 10.5 DVD the full retail install DVD, an upgrade DVD, or a DVD that came with another Mac?

Satellite P100-286 won't start anymore

Hi,
I have a P100-286 which I don't use very often but today I tried to switch it on and all I get is a flash from the lights near the speakers and the power light comes on for a few seconds then nothing.
The battery light is lit up red but it also won't start if I take the battery out a connect it to the mains?
Is it likely the laptop is dead or could it just be the battery?
I have only had it a few months and don't use it very often so the battery has not been under much load

Hmm sounds not good!
Try this firstly;
Remove the battery and disconnect the AC adaptor for about 20min.
After this short period, connect the battery and the AC adaptor again and try to start the notebook.
If this simply procedure does not help, you will have to contact the ASP in your country for a notebook check.
Your feedback is greatly appreciated.

Satellite L655D won't start anymore

Similar Messages

Maybe you are looking for