Satellite L675D: Blue Screen error after upgrading to Windows 8

Hello,
I've recently upgraded my Toshiba laptop to Windows 8 and every time I use it, after 5-10 minutes, I get a blue screen page of error and the laptop restarts.
The problem is really annoying.
I've discovered that if I don't plug in the battery charger, the laptop works normally, but I'd like to solve the problem properly.
What should I do?

> I've installed Windows 8 Pro with a regular activation key: I had Windows 7 before and I simply updated it to Windows 8. >I don't know about the drivers.. I think that may be the problem, but I also reckon the drivers are ok! Do you know a good way to check it out? Or where I can find the proper drivers?
Windows 8 drivers for Satellite L675D dont exist on Toshiba EU driver page. The L675D series does not support Windows 8.
However, even if the drivers are not available and Windows 8 is not supported, it should not be a big problem to run this system on the Satellite L675D.
You said that you simply updated the Win 7 to Win 8.
Maybe you should try a clean installation of Windows 8?
I think its worth a try in case its an software problem.
By the way: I assume this kind of problem did not appear using Windows 7. Right?

Similar Messages

What can I do if I get an internal power error after upgrading to Windows 10?

QuestionWhat can I do if I get an internal power error after upgrading to Windows 10?
AnswerSome laptops with AMD graphics that upgraded to Windows 10 are showing blue screens with error messages regarding Internal_Power_Error. If you receive this error, try the procedure in this article.
First, you'll need to quickly set the boot options to Safe Mode:
1. Hold the Windows key and press 'R' to open the run box.
2. Type MSCONFIG, then press ENTER.
3. Select the BOOT tab.
4. Under BOOT OPTIONS, check Safe boot, then select Minimal.
5. Click Apply, then OK.
6. Click Restart. (If prompted, click Restart anyway.)
From Safe Mode disable the AMD Display Driver:
1. Hold the Windows key and press the 'X' key to open a menu in the lower-left.
2. Click Device Manager.
3. Expand Display adapters to show the two display adapters.
4. Double click AMD Radeon R9 M200X Series.
5. Select the Driver tab.
6. Click Disable, then click Yes to confirm.
7. Click Close.
8. Hold the Windows key and press the 'R' key to open the run box.
9. Type MSCONFIG, then press ENTER.
10. Select the BOOT tab.
11. Uncheck Safe boot.
12. Click Apply, then OK.
13. Click Restart. (If prompted, click Restart anyway.)
From Windows 10 started with the AMD Display Driver disabled:
1. Hold the Windows key and press the 'X' key to open a menu in the lower-left.
2. Click Device Manager.
3. Expand Display adapters to show the two display adapters.
4. Double click AMD Radeon R9 M200X Series.
5. Select the Driver tab.
6. Click Update Driver.
7. Click Search automatically for updated driver software.
8. An AMD driver should be found and installed.
The driver that originally caused this problem is AMD display driver version 15.200.1046.2 dated 7/15/2015.
The driver installed through this process might have an older date, such as 15.200.1055.0 dated 7/6/2015. That's okay.

I'm having the same problem. I got error message 21. I went to apple store. they are saying i have a hardware error. Really, my phone was working before the update. Asked me for $150 to get another one when I am due to get a new one and wanted to pass this one on to my child.
Help please,
I will be glad to go back to the older software update

Blue screen error after USB connection

hello, I have a new 8100. All is great, all is working, but the problem appeared after I installed the software and I connected the mobile to the computer by USB... the blue screen error of Windows Vista appeared and then
after the automatic reboot of my computer
it said the following mistakes:
"Firma con problemas:
Nombre del evento de problema: BlueScreen                        ( name of the problem )
Versión del sistema operativo: 6.0.6000.2.0.0.768.3             ( OS version )
Id. de configuración regional: 3082                                    ( regional configuration ID )
Información adicional del problema:                                    ( aditional info on the problem )
BCCode: 4e
BCP1: 0000009A
BCP2: 0003EA16
BCP3: 00000006
BCP4: 00000002
OS Version: 6_0_6000
Service Pack: 0_0
Product: 768_1
Archivos que ayudan a describir el problema:       ( files which help to describe the problem )
C:\Windows\Minidump\Mini010609-03.dmp
C:\Users\antonio\AppData\Local\Temp\WER-110323-0.sysdata.xml
C:\Users\antonio\AppData\Local\Temp\WER6C68.tmp.version.txt
Lea nuestra declaración de privacidad:
http://go.microsoft.com/fwlink/?linkid=50163&clcid=0x0c0a
I hadn't anything wrong with my Vista OS before
thanks in advance
Solved!
Go to Solution.

Hi and welcome to the forums!
I don't read Spanish very well, but did you leave the Blackberry plugged in when you
rebooted the PC? Vista might have tried to used the BB as a drive for error checking or system functions.
Thanks,
Bifocals
Click Accept as Solution for posts that have solved your issue(s)!
Be sure to click Like! for those who have helped you.
Install BlackBerry Protect it's a free application designed to help find your lost BlackBerry smartphone, and keep the information on it secure.

Blue Screen Error after Synching

I had Blackberry Desktop Manager 7 installed on my WIndows XP machine...I have been getting Blue screen errors frequently after my Outlook is synched wiht the device..I was on BDM 6 prior to this and used to consistently get Blue Screen Errors. I used to think there was some other issue with the laptop until recently when I got a new one and I installed The desktop manager.
Once i realised that, I uninstalled the Software from my desktop yesterday but I read a lot of blogs that said that the BSOD will continue to come as your normal uninstalls are incomplete..Could you let me know how this can be fixed? Do you have a stable version of the desktop manger that doesnt give a BSOD?
I need to sync my device with Outlook everyday..and I cannot afford BSOD's everyday..

Hi and Welcome to the Community!
I suggest this thread:
http://supportforums.blackberry.com/t5/Desktop-Software-for-PC/Cleanly-quot-Starting-Over-quot-with-...
It starts with a process for cleanly starting over, and there is some discussion, and there is also a post (15) with links to older Desktop Software versions, if those are needed. Note that this is not, by any means, guaranteed to work...but it has worked for many to resolve issues they are having.
BSOD's are actually more rare of a problem, from what I've seen, and often indicate something more core wrong with the actual PC, Windows installation, or something else...and the RIM Desktop Software is simply revealing this deeper flaw rather than being the cause of it. In the worst case scenarios, I've actually heard of folks doing a clean rebuild of their PC (e.g., reinstalling Windows from scratch) and that rectifying the problem.
Ohhh...one last thing:
jinugeorge wrote:
Do you have a stable version of the desktop manger that doesnt give a BSOD?
FYI -- From the wording, I suspect you are misunderstanding the purpose of these forums. This is a user-to-user community, not a user-to/from-RIM channel for any communication whatsoever. So, by "Do You", you are actually asking that of other users, "out there", just like you who happen to be volunteering time to help others out.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blue screen error after updating to iOS8

After I updated my OS to iOS8.0.2...... I am getting a blue screen error again and again.
WHenever I will be using any application or opening any new application suddenly it will close with a blue screen.Then iPad restarts By itself.
PLease suggest.

Hi Chinmayee,
If your iPad is restarting unexpectedly, I would suggest that you troubleshoot using the steps in this article -
iOS: Device unexpectedly restarts, displays Apple logo, or powers off
Thanks for using Apple Support Communities.
Best,
Brett L

Satellite A200 - Blue Screen error when trying to open HWSetup

Hi,
I get a Windows Blue Screen error whenever I try to open HWSetup or access the Toshiba Flash Card using the Fn key.
Any ideas how to solve this?
Cheers!

Hello
The error message invalid serial number occurs if you try to install a software that is not designed for this notebook. Maybe you did download the HWsetup for an other notebook.
Check this!
Furthermore I have searched in the forum and maybe this could be useful for you:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=150557&#150557
Greets

STOP 0x0000007B Blue Screen Error after updating drivers for my P67A-C45

Hi!
I recently updated the drivers for my mainboard MSI P67A-C45. I did this with the update utility that follows this product. I choose the "update all" function so I'm not really sure what was actually updated but I remember seeing the bios and my realtek network drivers in the list of stuff being updated. Anyway, during (what I think was) the update of my BIOS (a CMD window appeared and started executing tasks) my computer suddenly restarts. I wasn't really paying attention during this process but it seemed like it wasn't finished and that the restart was unintentional.
Now during boot I get a Blue Screen message at the "Starting Windows" logo. The Blue Screen flashes by and my computer restarts instantly. It's a STOP 0x0000007B message which probably has to do with the drivers I just tried to update.
I have Windows 7 64-bit and I have tried the startup repair and the system restore function without any success.
Any ideas?
Can I revert these updates or maybe install the original drivers without formatting my hdd? I have the original CD that came with the board.
Best Regards
Victor

AHCI is a mode setting for the SATA controllers. You will find it in Integrated Peripherals. If you haven't set it to AHCI, it normally defaults to IDE mode. X79 platform being the exception. Yes. Remove LU5 & download & install all driver updates & such manually.
If your UEFI/BIOS did get flashed by LU5, I would recommend to remove the power cord from the PSU, remove the battery for awhile, clear CMOS, reset all the settings, especially check in the OC Section, CPU Features. Check to make sure there are no '0's showing. I don't know what your CPU is, so I don't know what to tell you to set the Core Ratio limit for each core if they are in fact sitting on 0. Disable Spread Spectrum & EuP 2013.

SSL Error after upgrading to Windows 8.1

After upgrade my Windows 8 to Windows 8.1, I got this SSL Error when I tried to go to "https://google.com":
http://i.stack.imgur.com/2kaXO.png
...and this in IE: http://i.stack.imgur.com/7Gxbw.png
I have did some research and tried to change my system time up to date, reset my modem and use wireshark to see if anybody is tracking my network, but none of them seem to be the problem.
Anyone can help me? Thanks a lot...
EDIT: I have checked my browsers and just figure out that every connection from my computer is not able to connect to any SSL connection, for example Yahoo Messenger login. I'm thinking my computer SSL Certificate got serious problem, is
there anyway to "reset" it?

Hi,
For the issue, it can happen for a wide variety of reasons.
I suggest we try the following methods to narrow down the issue.
Method 1.
Clear the Secure Sockets Layer (SSL) state:
In Internet Explorer, click Tools, and then click Internet Options.
Click the Content tab, and then click Clear SSL state.
Method 2.
Press Win+X, and then click Command Prompt(Admin).
At the command prompt, type sfc /scannow, and then press ENTER.
Method 3.
Press Win+R, type regedit in the box, and then press ENTER.
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\Main\FeatureControl
On the Edit menu, point to New, and then click Key.
Type FEATURE_ERROR_PAGE_BYPASS_ZONE_CHECK_FOR_HTTPS_KB950067 to name the new registry subkey, and then press ENTER.
On the Edit menu, point to New, and then click DWORD Value.
Type iexplore.exe to name the new registry entry, and then press ENTER.
On the Edit menu, click Modify.
Type 1, and then click OK.
Exit Registry Editor.
If the issue persists, I suggest you reinstall the IE to check the result.
Hope these could be helpful.
Regards,
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Satellite A10: blue screen error: 'kernel_inpage_data_error'

When I turn my laptop on, it works fine for a bit and then after a while (usually when i do an antivirus check) a blue screen appears saying 'windows xp was shut down because the file 'kernel_inpage_data_error' is not functioning or something'.
This error keeps on occuring. So I used the recovery disks to reinstall XP but the same error appeard again. And when I installed Xp again, it asks me to register & when I fill in my information it says 'we will call a telephone to register you' but then it says theres no dialtone.
I use broadband and xp doesn't ansk me what type of internet I use. It doesn't ask me at any point to enter my xp serial number. Does this mean im can't get automatic updates anymore or it's just that I am not registered yet?
How can I register? The laptop belonged to someone else before and things were registered in his account before. I would be glad if someone could kindly help me out.
cheers

Hi
First of all, on the Toshiba recovery CD you will find a OS image which is always activated and it's not possible or necessary to activate or to put any key.
Secondly I have found this Microsoft page which describes this error message:
http://support.microsoft.com/?kbid=315266
On this page you will find a information that it's possible that the master boot record is infected with a virus.
I don??t have any experience with "master boot record viruses" but maybe the whole HDD formatting will delete it. However, this is only a suggestion.
If you are not able to solve this issue by yourself you should ask the Toshiba service for the help.

Satellite M30: Blue screen error - how to diagnose what it is?

I have a hardware problem but I am not sure of the exact nature. Although I looks like the hard drive or something communicating to it.
Some two weeks ago I started to notice performance problems when loading something from the internal hard drive: overall function of the computer (like mouse cursor movement, mp3 playback) became hampered when the harddisk was loading (saving was less of a problem).
This was NOT the case when loading data or executing programs from an external usb harddrive. Today I got a blue screen informing me that this crash was probably due to new hardware or software, followed by a physical memory dump and a harsh shutdown. I rebooted the computer, but got the same problem after the login screen.
Trying to start it up in safe mode didn't work either and after a couple of tries it never got to the login screen anymore -- a few seconds after boot start there was a flash of a blue screen followed by an immediate shutdown.
Anyway, I used the product recovery dvd-rom but the problem is still there, i.e. I can boot now but I get the same blue screen every hour at least (seems to correlate with usage).
Instead of running off to buy a new harddrive I want to be sure that that is the (only) problem, and not some motherboard issue or what have you.
Hence my question: how can I diagnose what's wrong with my notebook?

Generally the best way is if you have a friend with the exact same portable. You can then take out your ram, and try it in their notebook, and try their ram in yours. If the problem persists on their computer, and yours boots up, its the ram. If not, the ram is fine. Then do the same with the HDD, again, if the problem doesnt happen on your computer, but happens on theirs, the HDD is bad, if not, your either down to CPU or Motherboard. A general overheating CPU goes into protection mode and automatically shuts the computer off. You dont get an error with overheating. But if the CPU has problems processing information it can generate blue screens. One sure way to find out if the CPU is defective is to continously reboot the computer and note the blue screen STOP error. If it remains the same constantly, then it is likely not the CPU, but the Motherboard. If it constantly changes from one error to the next, and generates 3 or 4 different errors, then you likely have a bad CPU.

Ati2dvag issue on Satellite M70 - blue screen error

Hello im hoping some one can help me with these problems that i have. Well from one day to start my computer I no longer start it in normal, and have to use safe mode, the computer changes the display on its own and it goes down to 16 bit colours,when i restart my computer hanging unless I boot it as safe mode and then other times i get the black screen saying that i can choose form safe mode etc. When i load up form safe mode it starts straight away and then i restart to go back into normal mode it hanging at black screen, but if i dont go into safe mode it takes ages to boot up.The blue screen that comes up says the following......
The device driver got stuck in a infinate loop. This usually indicates problems with the device itself or with the device driver programming the hardware incorrectly.
Please check with your hardware device vendor for any driver updates.
STOP:0x000000EA (0x86605C38,0x866563B0,0xF7CA2CB4,0x00000001)
ati2dvag
Beginning dump of physical memory.
Physical memory dump complete.
My laptop is Satellite M70, XP Home SP2. Video card is ATI X700.
I tried uninstalling Display driver, no help. I even tried formating HDD and reinstalled XP home with recovery by recovery DVD, even worse, I cannot even finish recovery process, it is always hanging when Start Windows, then same blue screen... Plus as soon as load windows xp, the display has very low resolution with many vertical lines evenly spread on screen...

Unfortunately, I think you have to return your notebook to the service point.
> The device driver got stuck in a infinite loop
For me it sounds like a corrupt graphic card.
I think there is no much to do and you have to ask for the technician help.

F.08 (S_ALR_87012277), program (RFSSLD00 ), screen errors after upgrade

Hi,
We upgraded a system from 4.6C to ECC 6.0, and we have a problem in G/L account balance report.
In the period field, fields are not seen with their default values when the report is run, and additionally when we write a period to the field, an error occurs and the message is: " Invalid field format (screen error) "..
An additional error is about the field descriptions. Some of the field descriptions are not seen in the screen, for example, normally in report F.08 in 6.0, the last check box field's description is: "Totals of all company codes", but there is nothing for that field in the upgraded system.
Is there common thing for the reports? or how can I make this report run?
Thank you,
Gul.

Hello,
I have solved the problem by regenerating the programs from SE38..
Thanks.

Multiple crashes, blue screen, reboots after upgrading to ios 7.1

Hi All.
My iphone 5s 32gb worked perfectly fine until upgraded to ios 7.1.
Now it keeps crashing, rebooting multiple times a day. Sometimes it enters in a rebooting loop.
I´ve tried reseting, restoring, downloading the upgrade and restoring again and again but the problem persists. Very frustrating.
I´ve enter to diagnostics and usage data on mi iphone and there are at leat 100 crash reports.
What should I? Whait for ios 8? Forget Apple products for good?
Thanks.

Thanks for your advice! I don´t live in the US. I can see there are a lot of people having the same issue after upgrading to ios 7.1. Is it possible that my iphone just got broken? I repeat that after the upgrade it worked perfectly fine.
Kind regards.

G60 laptop left without sound and bad screen issues after upgrading to Windows 8

I have a G60-458dx notebook that I just recently upgraded to windows 8.
Since then I have had no audio whatsoever, and anytime I try to wake the computer from sleep or hibernation, the screen won't turn on. To get the screen back I have to do a forced shut-down, then turn it back on.
I've tried uninstalling/reinstalling all of the relevant drivers (e.g. video, audio, chipset) to no avail. If anyone has any info on available generic drivers that would work, or updates from hp, you would make me a very happy man.
Here are the hardware id's for my audio and video.
HDAUDIO\FUNC_01&VEN_14F1&DEV_5051
PCI\VEN_8086&DEV_2A42

Try uninstalling the audio driver and installing this generic IDT audio driver: http://goo.gl/0IMBd
If that does not resolve your audio issue, then more than likely it is a hardware compatibility issue.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Satellite L30-10Y: Checksum error after upgrading to 2Gb RAM

Hi
I have a Satellite L30-10Y ^ months ago I upraded the RAM to 1.5Gb by adding a 1Gb RAM card to the 512Mb card supplied this worked fine.
I also upraded my sons Hi-Grade lapto with exactly the same specification of RAM which also worked fine. So I decided to up grade my L30 10Y with another card of the same specification to bring it upto 2 Gb as specified by TOSHIBA.
I booted the computer to find the hay presto after the start screen The Following message appeared *"_The file is possibly corrupt.
The file header checksum does not match the computed checksum_"* The computer then froze and I turned it off.
Checks I made Tried both cards in both slots No change, 1 card in both slots (one slot empty) Works fine. Other card in both slots(works Fine) Sons Card in my computer both slots (works fine) All three cards and 512mb card in all configuration of both slots and cards(works fine). All three 1gb cards in all configerations of cards and slots back to error message and some time 1 long beep and 2 short ones.
Yes the cards were installed properly. Cannot alter anything to do with BIOS although this can be accssed. Cannot run from dvd drive although I can select it.
Went back to 1.5Gb and reinstalled all OS from Toshiba recovery disk tried all over again same results. Running windows vista home basic, Bios is the latest download. RAM is compatible. Sons cheep Hi-Grade accepts all RAM in all Configurations no bother OS windows XP.
Can anyone think of anything I have not tried or should I just go and by a hi-grade computer?

Hi Eldorado
Thanks for your reply, 2 of these modules were bought 6 months ago from the same company at the same time (company Offtek) who do a computer scan and provide the modules specific to your computer, and even then I checked the specification of the modules against the upgrade that Toshiba who also scanned my computer on registration and the modules are DDR2 533MHz (PC2-4200) 200-PIN SODIMM . The Third module came from the same company with the same specification.
I am very sure that all three modules will be compatible to the computer, and the specifications does not require the modules are matched pairs like the old sd ram. So what we have is a computer that will run two completely differnt modules of different sizes made by different manufacturers possibly slightly different specs, but will not run two modules from the same manufacturer made at the same time with exactly the same spec.(Must be a break through of innovation for Toshiba!)
I think the beeps may have been a little misleading as these did not accord every time I started the computer over the many tests I did, I still have to look up what these codes signify. I tried looking in the Toshiba knowledge database but I think it's empty or they just don't have any knowledge complete waste of time or I don't know how to use it.
My next step its to contact Offtek and see what they suggest, Find out what the Header checksum is and what it is supposed to report and find out what the computed checksum is and why it does not match. One more thing I did notice that in the BIOS it did not report the full 2048mb it only reported 1984mb of RAM but I think this may be that video memory uses part of this. *_Unless someone out there knows something different_*

Satellite L675D: Blue Screen error after upgrading to Windows 8

Similar Messages

Maybe you are looking for