Satellite L850D - Display Adapters Code 43 error

Hi,
I have a Toshiba Satellite L850D and I installed the pc game Sims 3. For a few months, the game was working fine with minimum glitches occasionally until one day the game froze so I rebooted my laptop.
When I tried to open the game again, it came up with "The operation could not be completed. An unexpected error occurred (error code -43) I did some research and found out that my Display Adapters had problems and when I opened it it said "Windows has stopped this device because it has reported problems. (Code 43)"
How do I fix this?
And if I have to re-install the drivers, where can I get the download?

If you have European notebook model you can download driver from http://www.toshiba.eu/innovation/download_drivers_bios.jsp
Try to reinstall display driver.

Similar Messages

Satellite L850D: Black Screen - No Boot, No POST, No external screen

I have tried every known cure I could find on the internet to fix this issue, apart from trying to reflow the dual graphics chips that are onboard this machine, which in my mind is a design fault by Toshiba as the heat sink only covers one of the two Graphics Chips on this model of the Toshiba L850D, and to me this seems totally wrong due to heat transferrence and multiple issues I have come across with the Graphics Chips overheating from other manufactureres, even though they have heatsinks covering their graphics chips.
I've researched the internet for well over a week and, so far, nobody has provided an answer to anyone who is/was or had this issue, which seems to relate to other models as well.
I found a thread from January 2014 detailing this exact issue, but there was no answer provided to correct.
I'm not sure if this is allowed, but the relevant thread to this exact issue is provided : -
The actual model I have here is the Toshiba Satellite L850D, being model number PSKGEA-003001 and motherboard specific number is H000052650 WKC-51 Revision 2.1 or 7054D2745F87.
These seem to be so hard to find (or maybe should be extinct) even on eBay, so am wondering if it is a Toshiba FU that they no longer use Dual Graphics chips without a heat sink over both?
Have found similar style boards on eBay, being a H000051780 WKC29 and H000050830 WKC32 but all others seem to be back to one onboard Graphics or what appears to be on onboard Processor???.
Tried start-up without HDD, changed out existing RAM, swapped slots, taken out ODD, removed RAM and got the beep codes saying "Hey? Where's the RAM?", but nothing.... External monitor doesn't work, just says "Check Video Cable".
This all started when the only key that worked after a young user (their son) decided to delete files from his deceased dad's laptop and the laptop wouldn't boot, which was due to one too many deletions, that created a System File Error.
When I got the machine to fix, the only Key that seemd to work was F2 to get to BIOS (due to HDD O/S problems).... F8 Safe mode didn't work, so I changed BIOS to ODD as the primary start-up, but it still went straight to O/S load error (due to HDD problems).
Tried loadings Hirens Boot CD, but that failed, along withr any other CD/DVD placed in the ODD (which also failed even before I tried to change BIOS settings).
Except for motherboard replacement, I am totally stumped but, at this point of time, I can't even verify if HDD will fire up on replacement, when the cheapest Motherboard I can get is around $300-$350.
Has anyone found the answer to this challenge that other users have succeeded with?
Seems a waste if it is just a Chip.
Have also tried removing BIOS/CMOS Battery and left it out for a day or two (or more), but no change.
Would appreciate any help you can provide.
Appreciate any help.
Thank you
Daryl

Thank you Paolo30 for your comments.
Seems it may be motherboard failure, but I'm not sure why it happened when initial problem was just HDD file system repair required. Could a failing motherboard be the reason F8 didn't work and ODD was recognised but failed to load any boot discs?
As specified above, the actual model I have here is the Toshiba Satellite L850D, being model number PSKGEA-003001 and motherboard specific number is H000052650 WKC-51 Revision 2.1 or 7054D2745F87.
The WKC-51 seems to be harder to find than normal, but there are similar style boards on eBay, being a H000051780 WKC29 and H000050830 WKC32 with all others for the L850's seem to have reverted back to one onboard Graphics or what appears to be on onboard Processor.
Laptop turns on, can feel HDD is spinning, fan runs and laptop is heating up as if running normally, which to me appears either processor and possibly graphics could be fine, although the laptop doesn't seem to have HDD activity light showing... either way, no screen and no external video.
Tried sending an email to Toshiba, but as laptop is out of warranty, was not possible. Anyone know how to check specification differences between the WKC-51 and other similar boards?
Appreciate your assistance.
Daryl

Xtrememusic - a sudden code 10 error after installing the newest dri

I have been using the Xtrememusic for about two years and it has no problem at all until I tried to install the newest update.
It worked for about two days normally after the update before the code 0 error(this device cannot start)?appeared.
I've tried many methods, tried rolling back drivers, reinstalling drivers, etc. I have even used driver sweeper to clear all Creative's drivers but it'sjust didn't?work again.
Right now I can't even install the drivers which came from the CD
Is my card being killed by the new driver or what?
I am no experts in computing and any help would be greatly appreciated!
Here's my basic specs:
MB: Asus P5GD-VM
Ram:.5GB
Display card: ATI X600XT
Sound card: Xtrememusic with digital i/o connected

below address for your reference~
http://www.wretch.cc/blog/rogerpan96/2346306
this is the way to?remove?all creative driver files from system completely
. download the updated driver file from Creative website
2. extract the file with winrar kind application
3. find the "Setup" on the "Driver" folder, double click it
4. check options, "Driver Uninstallation" and "Delete all shared Creative audio driver files", click "OK"

How to use h:message to display HTML code in message from property file

I am using <h:message for="somecomponentid"/> to display the error message for a validator attached to a component and the error message which resides in message property file contains HTML elements like <br> and
The HTML doesnt get displayed properly and the code <br> etc is displayed instead.
Is there a method to get h:message to display HTML elements correcly.
[I know there is an h:outputFormat which has an escape parameter to allow HTML to be rendered correcly but it has no for parameter to specify the component id whose validation error message I want to display]
eg.
<h:message for="somecomponentid"/>
to display from errormessages.properties
com.somecompany.thevalidationerrormessage=You have an error<br> Please click here to return to homepage

Hello Ivan,
Fortunately I have just recently found a solution to my problem by using code by a developer who had already had this problem in the past and who provided a patch on the Apache MyFaces jira site.
See following link for the solution I downloaded and then used :
http://issues.apache.org/jira/browse/MYFACES-155
I believe they are intending to eventually release this in a future release of MyFaces extensions on this site.
I used the escape attribute on the tag to allow 'escaped' html code in error messages to be used.
Hope it solves your problem too..
Suhel

Hp g70-467cl: the ts-l633m DVD gives a code 39 error, I need a replacement driver to correct this

I have a HP G70-467CL Notebook PC Computer and I'm getting a (Code 39) error on the TSST corp CDDVDW TS-L633M ATA Device I'm running Windows Vista 64-bit Operating System the error says it is missing or has a corrupted driver issue. and when I checked for a solution nothing came up. Can anyone help me obtain the correct needed device driver? the only device drivers I could locate were for sound, display, chipset, modem, and LAN. I have already exhausted the available troubleshooters onsite HP and Microsoft. Thank you all.

Have you ran "Windows Update"? It can sometimes locate drivers for the hardware that is installed. If that doesn't work for you, let me know and I will see if I can find anything for you.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Yet another muse support post: Exit Code 7, ERROR: DW050:

I am so tired of this. I think I've used muse, problem free, once in the past 2 weeks. Here is the latest problem after an attempt to reinstall in effoert to fix an earlier problem.
I click install, it extracts the files, then installs them but bails anywhere from 35%-99%. Then i click "more details" and it opens the browser to display:
                    ++++++++++
Exit Code: 7 Please see specific errors and warnings below for troubleshooting. For example, ERROR: DW050 ...
-------------------------------------- Summary --------------------------------------
- 0 fatal error(s), 1 error(s), 0 warning(s)
ERROR: DW050: The following payload errors were found during install:
ERROR: DW050: - Adobe Muse: Install failed
                    ++++++++++
I'm a creative cloud member and have had no issues with any of the other programs of camparable significance; a few bugs here and there, but this muse product seems to have been a good idea but a little undercooked as far as my experience goes.
Unacceptable for muse memebers to be locked out of the programs they're paying for, but much more important, depend on. I've been a memeber for 2 weeks and it's been nothing but headache with muse. Muse is the product which sold me on becomming a member, now it's the only thing keeping me from publishing the work I've done on all the other programs.

Hi,
I apologize that you've ran into so many issues! Are you installing via the Adobe Applicatoin Manager? If so, try making sure Muse is completely uninstalled first -- if you're on Mac you can drag Muse to the trash and empty the trash, if you're on Windows there may be two entries for Muse under Uninstall Programs. You can search "Muse" in the upper right to filter. Make sure they are both uninstalled. You can then try via the Adobe Application Manager again.
If this still fails to work, please try installing with the following direct download links of Muse (click whichever OS you are using):
Latest Muse Mac: http://www.adobe.com/go/muse_latest_mac
Latest Muse Win: http://www.adobe.com/go/muse_latest_win
Please let me know if this helps.
Thanks,
Colby

G780 Nvidia GT 635M (Code 43 Error)

Hello,
I recently discovered earlier this week that in the Lenovo Solution Center, my NVIDIA card had been disabled due to code 43 error in Device Manager. I attempted to uninstall the video driver, clean my device of old drivers in safe mode, and install new drivers, all to no success.
Also, I'm unable to open my Nvidia Control Panel. When I run dxdiag, my Intel HD 4000 chipset appears as the video card being used.
Any assistance in this matter would be greatly appreciated!
Regards,
Evan

hi Evan,
Welcome to the Lenovo Forums.
For units with dual graphics (Intel + Nvidia), these machines uses the Nvidia Optimus technology (it's normal to get the Intel HD4000 Graphics in dxdiag),
For the graphics switching to work, you wil need to install the following in order (reboot if necessary):
For Windows 8:
1st - Intel Video Driver
2nd - NVIDIA VGA Driver
To know if graphics switching is working, you will need to enable both the Show notification Tray Icon and Display GPU Activity Icon in Notification Area under the Nvidia Control Panel
- this should notify you if the Nvidia GPU is being used
- Link to picture
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to fix this problem? Secure Connection Failed, SSL received a record with an incorrect Message Authentication Code. (Error code: ssl_error_bad_mac_read)

Secure Connection Failed
SSL received a record with an incorrect Message Authentication Code. (Error code: ssl_error_bad_mac_read)
I have been receiving this error message recently when I tried to access school elearning websites and other school related websites, I have also tried on internet explorer and it shows page cannot be displayed. I have been trying the available solutions to solve it but none of them work. Is there alternative solutions available? Please advise. Thanks.

It works after I disabled IPv6 in Firefox. Thank you for your help :)

Code:OpenMedia Error with Bluetooth

I have an E65
I am running
PC Connectivity Solution:
Version 8.15.0.0
[Nokia Connectivity Cable Driver:]
Version 6.86.11.0
Operating system:
Microsoft Windows XP 32-bit Edition, Service Pack 2
Language: English
Language for non-Unicode programs: English
Detected Internet browsers:
- Microsoft Internet Explorer 7.0 (Default browser)
Detected Bluetooth stacks:
- Microsoft (Version: 5.1.2600, Build: 2180)
I have IVT BlueSoleil 1.6.1.4
When I try and manage connection to use bluetooth I get Code: OpenMedia error,
Anyone have any ideas.

Although I had tried both USB ports on the left side of the machine, I had never tried the USB port on the right rear of the machine.
Plugging the cellular device in the USB port on the back of the computer allowed for successful installation of both the 3G and 4G network adapters. With the 4G network adapter finally installed successfully, I could connect to the 4G network.

Code 10 Error CD-ROM

I have a Satellite L355-S7812 and the CD-ROM driver will not register any CD/DVD after months of it working fine. I tried to uninstall and download the driver. Still had a Code 10 error in the device manager. Please help.

To solve the issue, you have to edit the Windows Registry:
Click Start, then Run, type REGEDIT and click OK.
Locate and then remove the following registry values:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}\LowerFilters
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}\UpperFilters
Close Registry Editor.
Reboot the system for the changes to take effect.

MATSHlTA UJ8E2 DVD Code 19 error Windows 8

Hi, I have a Toshiba Satellite C55-A with Window's 8 and the DVD drive is a Mat**bleep**a UJ8E2. The drive is not working and is giving me a code 19 error. The message says "Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)". I've tried updating it uninstalling it and reinstalling it and it does not fix the problem.

This solution did not fix my issue.
I have tried searching for the driver. Windows says I have the most updated driver and yet it gives me the error 19 code and yet it shows an error exclamation point in my device manager.
It was working fine last week when I was ripping CDs onto itunes. Today my disc drive just is NOT recognized in the MY COMPUTER tab and won't auto play or open up.
Can someone please help me?

Code 19 error on teac dv-w28s-vtf drive!

After trying to boot up a CD, I discovered the CD drive had a code 19 error so after several unsuccessful fixes, I ended up uninstalling the teac dv-w28s-vtf drive... Yet nothing has helped The TEAC website has no fixes and I have tried the windows 7 troubleshooter... I would appreciate a solution! By the way I own a Toshiba Satellite L655-S5096.
Solved!
Go to Solution.

Satellite L655-S5096
Code 19 indicates a problem in the registry. Probably this will fix it.
Your CD drive or DVD drive is missing or is not recognized by Windows or other programs
-Jerry

ERROR OGG-00868 Error code 1291, error message: ORA-01291: missing logfile

OGG Version 12.1.2.1.0 OGGCORE_12.1.2.1.
DB : 11.2.0.4.3
I am getting below error.
2014-12-31 09:53:09 ERROR   OGG-00868 Error code 1291, error message: ORA-01291: missing logfile
(Missing Log File <unknown>. Read Position SCN: 2585.802983323 (11103293443483)).
Our solution uses ADG and OGG
We have source and target where ADG was setup . We later broke ADG setup and made Oracle DB's in source and target into standalone.
As part of our solution during our deployment window ,we would break ADG i.e we would make both the source and target as independent DB’s with PRIMARY Read /Write mode.
-Take Guaranteed restore point on Source DB so that we can flash back at later stage(so of now we have not executed flash back command)
-Once ADG config is disabled we will start the OGG extract which is already configured before =We are at this stage where we are hit with errors and extract is not starting .

Hi ,
The error shows it is waiting for the Logfile. The Integrated extract mainly needs of the availability of two things.
1. Archivelogs.
2. Trail Files.
Both should be retained to the needed / required level.
Please execute the below query and check the status of the Extract / Capture process.
The below query displays the information of each capture process in a database.,
COLUMN CAPTURE_NAME HEADING 'Capture|Name' FORMAT A7
COLUMN PROCESS_NAME HEADING 'Capture|Process|Number' FORMAT A7
COLUMN SID HEADING 'Session|ID' FORMAT 9999
COLUMN SERIAL# HEADING 'Session|Serial|Number' FORMAT 9999
COLUMN STATE HEADING 'State' FORMAT A20
COLUMN TOTAL_MESSAGES_CAPTURED HEADING 'Redo|Entries|Evaluated|In Detail' FORMAT 9999999
COLUMN TOTAL_MESSAGES_ENQUEUED HEADING 'Total|LCRs|Enqueued' FORMAT 9999999999
SELECT c.CAPTURE_NAME,
       SUBSTR(s.PROGRAM,INSTR(s.PROGRAM,'(')+1,4) PROCESS_NAME,
       c.SID,
       c.SERIAL#,
       c.STATE,
       c.TOTAL_MESSAGES_CAPTURED,
       c.TOTAL_MESSAGES_ENQUEUED
FROM V$STREAMS_CAPTURE c, V$SESSION s
WHERE c.SID = s.SID AND
        c.SERIAL# = s.SERIAL#;
Also run this query to check, if the capture is waiting for which logfile.,
COLUMN CONSUMER_NAME HEADING 'Capture|Process|Name' FORMAT A15
COLUMN SOURCE_DATABASE HEADING 'Source|Database' FORMAT A10
COLUMN SEQUENCE# HEADING 'Sequence|Number' FORMAT 99999
COLUMN NAME HEADING 'Required|Archived Redo Log|File Name' FORMAT A40
SELECT r.CONSUMER_NAME,
       r.SOURCE_DATABASE,
       r.SEQUENCE#,
       r.NAME
FROM DBA_REGISTERED_ARCHIVED_LOG r, DBA_CAPTURE c
WHERE r.CONSUMER_NAME = c.CAPTURE_NAME AND
        r.NEXT_SCN      >= c.REQUIRED_CHECKPOINT_SCN;
The above query clearly shows for which logfile the Extract / Capture process is waiting. Check if that logfile is available in your system.
Regards,
Veera

Satellite L850D/00312 - catalyst center / graphics properties wont open

Had to do a fresh install of windows 7 as HDD completely Died.
Have installed drivers and all ok in device manager but the Graphics properties wont open, keeps saying stopped working.
Please tell me what I need to do?
install drivers in specific order? what order? do I Need to start again and fresh install windows 7 again?
Thanks,

To be honest the Satellite L850D/00312 is not known to me but as far as I know to get the ATI/AMD display driver working, no special installation order is needed.
Maybe you should simply uninstall the ATI graphic card driver from the system and after new notebook reboot, you should install the graphic driver package once again.
In my opinion this simple procedure should help you to get it working.

Error Code :-5002 Error Message :Enter valid currency , '51100000-01-001-0

Hi all,
I have found a error "Error Code :-5002 Error Message :Enter valid currency , '51100000-01-001-01'" while adding the DELIVERY document.
I have made a customer and assign then "EURO" currency and add delivery document then it prompts error.
Could anyone solve this problem. is there any setting which i am missing..??
Regards
Sandesh

HI Sandesh,
Check Sap note :1252328
and also check below thread of similar issue:
Re: 'Invalid Currency' error when attempting to deliver order
Hope this will solve your issue.
Thanks,
Neetu

Satellite L850D - Display Adapters Code 43 error

Similar Messages

Maybe you are looking for