Satellite L870-165 does not work after being repaired by their service

Laptop Toshiba warranty does not work after being repaired by their service twice.
Model: Satellite L870-165
Computer will not boot, stays with black screen stating: No bootable device-Please restart your system
After reboot still happening the same.
I called Toshiba phone incident and after trying several options I said take him to repair the service.
They first told me it was the hard drive, then phoned me to indicate that reinstalling and finally it was the motherboard, which supposedly changed. The day after being picked computer repair returned to give exactly the same error, only malfunctioned one evening.
After another call to 902 the Toshiba warranty service, I went back to take the service, this time I changed the hard drive. When I got home the computer did not start even once, again gives the same error.
I believe that this team comes with a factory default so that its solution is not easy because even the technical service told me that I did not know what else to do with it.

>Computer will not boot, stays with black screen stating: No bootable device-Please restart your system
This message pops up because the notebook cannot find the Windows system.
There could be either an problem with the HDD or maybe the HDD is OK but the Windows system isnt preinstalled properly.
You said that the service agent changed the HDD. But did someone install the Windows system?
You can try to do it yourself take your recovery disk (hopefully you created such disk in the past) and boot from the recovery disk in order to install the system.
In case booting from the Disk would not be possible, go to BIOS (F2) and disable the secure boot and change from UEFI to CSM mode

Similar Messages

  • IPad 3 Why 3G does not work after being on WiFi

    When I take my iPad 3 out of my house, I have to reboot it to get a 3G connection. The 3g icon shows that it is connected but when I try and access any connection it says no internet connection. My iPad 1 seemed to work ok. I've also tried putting it in Airplane mode and back again but this has no effect.
    Any suggestions please? Many thanks.

    All of you are not ALONE ! Most of us here in Singapore be it with Singtel, Starhub or M1 3G network, all of us with the "NewiPad" are sharing the same pain of this "Cellular data not connected" problem. When this problem occurred, one must power cycle or at least reset network setting to get the 3G data connection work again. A daily of power cycle 3~5 times for my new iPad was need. All methods like below tried but still DOES NOT fix the problem.
    1. Reset Network setting.
    2. Reset iPad back to default.
    3. Changed Singtel APN name from "e-ideas" to "internet" still the same.
    4. Changed a complete brand new sim card.
    My current fixed was, called up Singtel ISP to reset my iPad 21Mbps 3G Line in their system. In my end, I need to power off my new iPad to complete the cycle. So far it has been working fine for 42 hours now.
    By looking at the "General > About > Cellular Data Number" was "Unknown". This lead me to think it might be a bug in current new iPad iOS 5.1. To be more precise, it might narrow down to the "Big & Bad Qualcomm Radio chipset Driver" problem?
    If that was true, jess.. I truly dislike "Qualcomm inside" devices. It make me come to remembered Dopod/HTC D810 the most funniest released WM device in history. When D810 first hit the market, it does not features any gps function at all when in true fact D810 did come with "Qualcomm" GPS chipset built-in since day 1. Dopod/HTC took more than 6 months to release a very crippled firmware that included Qualcomm GPS chipset driver with lots of trouble and start announce all the customers in the world, including those who's bought D810 more than 6 months ago. What a joke!
    That's not all the "Qualcomm" funny facts. They then hit the wall again with Dopod/HTC Tytn-II, another WM cellphone with "Qualcomm 3D Graphic chip built-in, BUT WITH NO 3D DRIVER BUILT-IN". Hahaha.. what another big "QUALCOMM" historical joke of all time.
    Anyway, hopefully Apple can found the actual trouble or fixed "might be Qualcomm driver problem again?" in the next iOS 5.2 release.
    Until then, I've wishes everyone with the cellular data connection trouble eventually manage to solved your headache in any solutions provided by many and living happier with your new iPad, the same for me.

  • Satellite A110-228 LAN does not work after hibernate

    Well, subject says it all, really. The LAN (wired) network does not work after hibernate.
    It seems it cannot find the DHCP server, so after a while it gets a 169.* address.
    After a reboot, the network functions as usual (gets a IP address from the DHCP server)
    Tried the usual things, disconnecting the cable, disabling the LAN device, battery or AC adapter, the behavior is reproducible.
    The wireless network will be restored after a hibernate.
    It needs a little help though (right click on the icon and "recover" or whatever it is called in English)
    Any suggestions?
    Wilm Boerhout

    Hi guys
    In the Toshiba HW setup which is placed in the control panel the options Wake-up on LAN and Built-in LAN should be enabled.
    I think the options are disabled by default.
    Furthermore the default setting for Wake on Settings is OS controlled. To use the Wake-up on LAN function under power off mode, in the device driver for the network card under the menu point Wake On Settings the Value Wake on Magic & Directed must be set.
    Please check this how to enable WOL (first time use):
    1. Go to [Start] -> [Control Panel] -> [Toshiba HWSetup] -> [LAN] tab
    2. Enable Wake-up on LAN
    3. Click [Apply]. System will request to reboot.
    4. After the reboot go to [Start] -> [Control Panel] -> select [System]
    5. On system properties dialog box select [Hardware] tab -> click [Device manager]
    6. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
    7. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
    8. Press [OK] to close the dialog box.

  • Continuous with the problem, the headphone does not work after having my iphone ios 8.0.2 updated

    the headset does not work after having my iphone ios 8.0.2 updated to me is very annoying to have to be answering speakerphone is not private and can not go with the hands-free all the time

    I had the same issue until I updated my apps through iTunes. I had over 100 updates, but none of them showed on my iPod. After they updated everything started syncing like it is supposed. Go to the apps library and check for updates. After everything syncs leave your iPhone/ipod/ipad connected if the spinning arrows at the top is still spinning. It means that things are still being added. If you go to settings > general > about, you will see it loading songs, videos, photos, etc. If you back out of "about" and then go back to it you will see the numbers for each one change.

  • Card slot does not work after update (14/10/2011)

    Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
    MacBook Pro 13 OS ver. 10.6.8

    Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

  • HT1688 My Hot Spot does not work after update to 6.0.1.  Service is with ATT.  Apple says problem is with ATT, ATT says problem is with Apple.  Anyone else having this problem?

    My Hot Spot does not work after update to 6.0.1.  Any suggestions?

    Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
    so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
    so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal.

  • Click to activate does not work after update

    Click to activate plugin does not work after updating to version 23.0.1

    hello Kamullia, if you have set click-to-play to true in about:config you can now go to the ''addons-manager > plugins'' section and set the permissions individually for each plugin type.

  • WiFi iPhone 4S does not work after update iOS 6.0

    WiFi iPhone 4S does not work after update iOS 6.0

    This sounds more like a hardware issue.
    Have you checked that the dock connector port is not dirty?

  • Flash player does not work after I installed it

    Flash player does not work after I installed it

    I'm using Mac Osx and my browser is Safari
    Date: Wed, 5 Feb 2014 00:41:29 -0800
    From: [email protected]
    To: [email protected]
    Subject: Flash player does not work after I installed
        Re: Flash player does not work after I installed it
        created by Mike M in Installing Flash Player - View the full discussion
    This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
    What OS are you using?
    http://mmonlinedesigns.com/images/os.png
    What browser?
    http://mmonlinedesigns.com/images/browsers.png
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
               Start a new discussion in Installing Flash Player at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

  • My sound system does not work AFTER installing pc to tv wireless connection

    my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

    Hi,
    You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
    Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
    one used by the Form contact for Form Invoice.
    Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
    VS General Question forum mainly discusses
    the usage of Visual Studio IDE such as
    WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
    System and Visual Studio Editor.
    Thanks,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • Apple TV does not work after trying to update software. Main light keeps blinking and on the screen shows itunes icon and a usb cable. What does that means?

    My Apple TV does not work after trying to install the new software update. The main light keeps blinking rapidly and on the screen it shows the itunes icon and a USB cable. What does that mean?

    The Apple TV is in recovery mode. Try to restore the Apple TV. Follow the link for instructions on the restore process.
    http://support.apple.com/kb/HT4367

  • IMessage does not work after upgrade to iOS 8.1.3 to my iPad 4

    iMessage does not work after upgrade to iOS 8.1.3 on my iPad 4

    I Fixed it by trying to sign in with a different ID and canceling when it asked For a password and then signed in with my ID and it works! No more error message. I got this idea from another discussion. Thank you for replying though.

  • "F11 System Recovery" during boot does not work after Cloning hard drive.

    Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
    HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
    Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
    Startup Menu (F11 System Menu works properly) only on original hard drive.
    Following obtained from Disk Management & diskpart in Command Prompt.
                                     GPT Disk <700GB>
    Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
    Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
    Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
    Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
    Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
    Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
    Partition 7 NTFS Primary 26MB/350MB [Recovery]
    Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
    I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
    Acronis True Image 2015
    Acronis Backup for PC
    AOMEI Backupper Professional
    Macrium Reflect
    Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
    “Recovery
    Your PC needs to be repaired
    A required device isn’t connected or can’t be accessed.
    Error code: 0xc0000225
    You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
    Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
    Thank you in advanced.

    Hi,
    How did you clone the HDD ? One-for-one or different method ?
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • TX2500Z touchscreen does not work after Windows7 upgrade from HP specific to S/N, etc on laptop.

    My TX2500Z touchscreen does not work after I upgraded to Windows 7. I cannot find any support or drivers, etc. to fix.  I bought Windows 7 directly from HP specific to my P/N and S/N on my TX2500Z.  Any help? Thanks.

    after 2,5 days (spending half a day within the apple shop as well with this problem) i have it all back on track.
    i did a lot of different things: trying to remove and reinstall iPhoto; did a SL installation over the old SL I had on my HD; backing up all the data of course before and reformatting my HD and installing a new clean SL version on it + a new clean version of iLife9 with all the updates and than I migrate with migrate assistant all the data and setting with time machine back onto it, but all this didn't work, because it also migrated the error/bug through time machine with it.
    so at the end i just installed a brand new, clean SL version on my hard drive, than I did the updates and put all my data, photos, docs, movies, mail, bookmarks, music, etc manual back into the system (drag and drop from my external HD, where i had an exact copy of my internal HD) and did all the settings again in all the different programs.
    the only thing i used migrant assistant with time machine for was for the programs. it seems to work now all fine and i even got more free space on my HD, because some of the old stuff i always carried with me but i never used, i didn't take over.
    basically everything is clean now. At least i hope and works fine. touch wood!

  • PCI wireless card does not work after restart - FM2-A55M-E33

    Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
    BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
    I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
    Does anyone know more about this issue?

    Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
    ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
    ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
    ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
    And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
    I am unable to find any useful information in the logs.
    Got any more suggestions?
    Thanks! (And sorry to disturb so much)

Maybe you are looking for