Satellite M30-107 does not boot correctly after Recovery disk usage

Hi
I've recently got hold of a second hand toshiba Satellite M30-107 laptop, and decided to freshen it up.
I used the toshiba recovery disk, but after doing so the laptop no longer loads windows.
When turned on it shows the Toshiba start up disk for about a second then goes to a blank screen and freezes.
When turned off and on again a screen comes up reporting an error in shutting down and gives the options to start in safe mode etc. but choosing any of the options causes the machine to freeze.
Any help or advice would be much appreciated.
Thanks
jt

Hi
Sounds a little bit like the notebook does not boot due to the Windows software issue
Did you recover the M30 with the original Toshiba recovery CD which was supplied with this M30 unit?
Maybe Im wrong but for me it looks like a wrong recovery CD was used and an image with non compatible drivers was installed
You could try to install the OS from original Microsoft Win XP CD and could check if it would be possible to get the notebook ruining using clean OS.
In such case we ( you and me ;) ) could find out if this issue could be related to the software or hardware.
Bye

Similar Messages

Satellite L745D-S4214 Does not boot; HDD recovery partition not working

I tried to apply the recent windows 7 updates and my laptop no longer boots. I tried to press F12 and select the HDD Recovery partition, but it does not boot regardless. There is a message that it does not communicate to a specific device. I believe the address called out was 0xc0000e9, but I am going by memory. I never created a recovery CD because I thought I was covered by the HDD partitions. This was purchased on 10/26/2012, so it should still be under warranty.
PLEASE HELP!

Hi I'm going to assume that your recovery works like mine and that the recovery partition is still good and not corrupted.
Shut down your PC. Press F12 and select HDD recovery. Click enter. This should start the recovery from the hidden recovery partition.
PS I would advise you to make the recovery discs or USB recovery Try this first.
Perform a power cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with boot problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Remove the battery (if the model has a removable battery).
Unplug all wires or peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Hold down the power button for thirty seconds.
Reattach the battery.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Try starting the computer.
If your laptop starts normally now, you're done!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Remote does not work correctly after update

Hello,
the subject explain it already:
After upgrading to 2.3 the apple remote does not work correctly anymore:
I need to push the buttons twice, and than atv is only reacting sometimes.
Any ideas?
BR
Frank

Same problem here. First, I thought it was the Apple remote's battery. I replaced that and the problem persisted. I then used my digital video camera to verify that the remote was actually transmitting infrared, it was. In frustration, I tapped the buttons rapidly while pointing at the Apple TV. The Apple TV responded. The next button press it failed to respond. I tapped rapidly again and it finally responded. After many many rapid presses, while pointing directly at the Apple TV, it finally began responding to all presses. Once I'd regained control (I thought) I unpaired and re-paired the remote. Everything continued to work. At that time I also saw that I could "learn" another remote. So, I set up my Samsung TV remote. Sweet. Until the Apple TV went into screensaver mode again and I had to go through the same rapid button press sequence... with either the Apple remote or my learned Samsung remote. Conclusion, since the Apple TV will become fully responsive after the rapid button press sequence, it is certainly a software related problem.

Cisco Nexus 5596 does not boots up after NX-OS upgrade 5.1.3.N1.1 to 6.0.2.N2.5 [CSCun66310]

Hello Friends,
Just want to save your precious time & effort, while doing Nexus 5596 upgrades so wanted to share some useful info which you can have a look prior to your upgrades of Cisco Nexus 5596 device.
I recently ran into trouble when upgarding one of datacenter switch Nexus 5596 does not boots up and after investigation from Cisco TAC it comes out to be Bug documented below.
https://tools.cisco.com/bugsearch/bug/CSCun66310/?reffering_site=dumpcr
My Upgrade path of device was : 5.1(3)N1(1)  to 6.0(2)N2(5).
Since this upgarde involves upgrade of Bios and Power sequensor, I was having some doubts to get this succesfully upgraded, But there was more twist involved in this upgrade which I came to know after contacting Cisco TAC for my died Nexus 5596 device and got info that if you have below impacted version in your Nexus 5596 device and you are planning to do Upgrade, then you migh RUN into this serious BUG aftre which device won't come up at all and only Option left is to replace with RMA device.
PID                          Impacted                   Hardware versions      Updated Versions
UCS-FI-6296UP                                            1.0                                       1.1
N5K-C5596UP                                              1.0                                        1.1
N5K-C5596T                                                 1.1                                         1.2
You can check hardware version using below command from your device.
5596# show sprom sup | inc H/W
H/W Version     : 1.1
So please be carefull when planning your Nexus 5596 upgrade and verify above things as this Bug is not present anywhere in Upgrade docuemntations unfortunately.
Hope this will help and save someone's precious Time.

Today "upgraded" our switch (N5k-C5596UP) to from 5.1(2)N1 to 7.0(5) and after reboot no life from the switch either. Even no console response. show sprom sup | inc H/W shows 1:0.
Only thing we could do is RMA the switch. So what must I do with these switches? Have still to do 3 of them.

Login Window: Screen does not refresh correctly after waking 10.7.2 iMac and MacBook.

I have a client who brought to my attention that when we wakes his iMac and MacBook after the screen dims or sleeps at login screen, that sometimes the screen does not refresh correctly and you must use the cursor to basically "clear the screen." I have witnessed this myself and elimiated all third party products and this still happens. I am starting to believe that is is a bug in 10.7.2. Has anyone witnessed this or have any suggestions on how to remedy? Thank you.

Thanks lynque. It turns out I did need a keychain repair, but that didn't fix the problem. I probably should have done this earlier, but I ended up unplugging all peripherals (2 firewire + 3 USB) then powered up without issue.
So I shut down, plugged in one at a time, and ran into the problem again after plugging in an external hard drive (WD My Book Essential). I repaired with disk utility, but the problem remained.
I then rebuilt the partitions with Disk Warrior, and now everything seems to work....

Satellite P840/016 does not boot from CD or DVD

Using F2 enabled the BIOS to boot from optical drive, saved and re-started. Finds the bootable CD created from the same laptop using the repair disc from Windows 7 recovery but does not boot.
Tried Ubuntu DVD which works as boot disk on all other laptops - still does not boot.
Changed the setting in BIOS to non-secure - same problem.

Thanks - tried this pressing F12. Message appears on the screen to press any key to boot from DVD. Key pressed, the DVD is read and then delay with blank screen. The laptop goes back to start screen and than goes to boot from the HDD. Also tried making USB as bootable. Pressed F12 and selected USB as boot device. Reads the USB and after a period of time boots from HDD.
Checked DVD driver - it is the latest.
Operating system is Windows 8 pro.
RAM is 8GB, processor is I7 and HDD is 1 TB. Laptop is only 3 weeks old

HT4840 Boot camp does not boot to Windows 7 disk after completing disk partition - white blank screen

After completing the partitionning of the hard disk, the iMac reboots but nothing happens. The system does not boot from the Windows 7 disk.
A blank screen appears and that's all.
I have tried to manually boot from the disk by pressing the <Alt> kei will restarting the iMac. The system display the option of booting from the iMac hard disk or the Windows 7 disk. Seelcting the Windows 7 option does noting.
Thanks in helping me find a solution to my boot problem.
Danarc54

Are using a 64 bit version or a 32 bit version of Windows?
I'm not up on the iMacs but according to this article you may not be able to use 64bit Windows.

Re: Satellite T110-107 will not boot into recovery option screen using f8 key.

I have tried numerous times and can't get the system recovery option by intermittently hitting the *f8 key during startup* like it says in the manual, it just goes straight into Windows. I just installed the latest BIOS but that didn't help either. I have no disks for recovery but I would like to get the f8 issue solved anyway. Everything else works perfectly. Thanks.

Hi
Maybe you didnt press the F8 in the right manner
You have to press F8 immediately after the notebook has been powered up!!!
Press it several times to be 100% sure
If this will not function, create the recovery disk!!! This should be done at first before doing anything with the notebook!!!!
The recovery disk is always important and helpful if something would go wrong with the HDD!!!
After creating the recovery disk use this disk in order to set the notebook back to the same state like at the first day of purchase

Satellite M30-344 would not boot up

Hello!
I have there a Toshiba Satellite M30-344.
I didn't use the notebook since several weeks. Now everytime I boot the Notebook an error appears: "0203: Failure IDE #2 - Do you want to run setup".
Since the last use I didn't change anything on the configuration.
The only problem there was, is that I has forgotten to turn him off and he kept running under my table for more than 2 weeks.
Is there a way to solve this problem?
Thank you for your help.
Greetings from Germany!

Hi,
...oh dear, you are not kidding?? You forgotten to turn him off and kept him under a table??? Man, THATs REALLY weird. :)
And now to help you with your problem:
IDE#2 means the DVD-drive, so you have some options to bring your machine to life, since your DVD-drive maybe could be faulty.
Firstly, try to get into BIOS and make everything to default. If you didnt get any results, then remove the drive by unscrewing the screw under the drive and pulling the drive gently out
of tha machine. You can also after you unscrewed it, open the drive and then gently pulling it by the inner carriage of the drive.
If unsure how to make or to much fear to damage something, then bring your machine to an local ASP and they will help you with your little problem.
So I think, your drive is probably faulty.
Greets
P.S.: And try to remember next time when what you keep under your table like notebooks, pets, humans, gremlins.... ;)
Nice weekened

Satellite C850-1j1 does not boot anymore

my laptop Satellite C850-1j1 doesn't boot anymore.
Happened after partition changes. shows a error screen telling me the computer needs to be repaired using recoverymedia,
I've got a working hirens boot cd and usb (tested on other comp.) but the laptop is not responding
op. system win 8 64 bit brandnew.
suggestions are welcome

Hi
The message says that you have to install the system again using recovery media
As far as I know the notebook was preinstalled with the WIN 8 64BIT system.
You can use the HDD recovery option
Power on the unit and press F12.
Then choose HDD recovery option appearing in the boot menu.
Follow the instruction on the screen
Good luck!

VirtualBox does not start correctly after kernel update

Just recently I have been unable to start VirtualBox after a kernel update. That is to say it seems to be running, but displays nothing.
The following processes are listed: VirtualBox, VBoxSVC, VBoxSVC, VBoxXPCOMPCD
The following modules are loaded: vboxdrv, vboxnetflt, vboxnetadp
Yesterday, when the same thing happened, I reinstalled VirtualBox and it worked correctly again.
I recently upgraded to systemd which has caused me some other problems, so that might have something to do with it
Cheers
Andrew
* Arch x86_64 up to date, NVidia proprietary drivers, AMD processor

Updated - Rebooted (systemd does hang on reboot or shutdown but turned PC off and restarted)
Confirmed that vbox modules are loaded:
vboxnetflt 16807 0
vboxnetadp 18419 0
vboxdrv 1823469 2 vboxnetadp,vboxnetflt
Started VirtualBox - nothing displayed.
ps -el shows
0 S 501 1036 614 0 80 0 - 111245 futex_ ? 00:00:00 VirtualBox
0 S 501 1050 1 0 80 0 - 29408 poll_s ? 00:00:00 VBoxXPCOMIPCD
0 S 501 1056 1 0 80 0 - 53178 futex_ ? 00:00:00 VBoxSVC
output as above
$ uname -a
Linux ezcool 3.6.4-1-ARCH #1 SMP PREEMPT Mon Oct 29 09:49:00 CET 2012 x86_64 GNU/Linux
# pacman -Qi linux
Name : linux
Version : 3.6.4-1
URL : http://www.kernel.org/
Licenses : GPL2
Groups : base
Provides : kernel26=3.6.4
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : nvidia virtualbox-host-modules
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 61124.00 KiB
Packager : Tobias Powalowski <[email protected]>
Architecture : x86_64
Build Date : Mon 29 Oct 2012 09:55:27 CET
Install Date : Wed 31 Oct 2012 12:28:40 CET
Install Reason : Explicitly installed
Install Script : Yes
Description : The linux kernel and modules
# pacman -Qi virtualbox-host-modules
Name : virtualbox-host-modules
Version : 4.2.4-2
URL : http://virtualbox.org
Licenses : GPL
Groups : None
Provides : None
Depends On : linux>=3.6 linux<3.7
Optional Deps : None
Required By : virtualbox
Conflicts With : virtualbox-modules
Replaces : virtualbox-modules
Installed Size : 168.00 KiB
Packager : Evangelos Foutras <[email protected]>
Architecture : x86_64
Build Date : Mon 29 Oct 2012 17:23:20 CET
Install Date : Wed 31 Oct 2012 12:29:06 CET
Install Reason : Installed as a dependency for another package
Install Script : Yes
Description : Host kernel modules for VirtualBox
Kill all VBox processes, VBoxSVC does not quit but is marked (defunct)
Reload modules
Confirm modules loaded
vboxnetflt 16807 0
vboxnetadp 18419 0
vboxdrv 1823469 2 vboxnetadp,vboxnetflt
Start VirtualBox - nothing
pacman -Rdd virtualbox-host-modules
pacman -S virtualbox-host-modules
modprobe vboxdrv
Start VirtualBox - nothing
pacman -R virtualbox virtualbox-host-modules
pacman -S virtualbox virtualbox-host-modules
useradd -G vboxusers
Start VirtualBox - nothing
The problem seems to be something to do with nspr-2. I am getting multiple errors in the journal:
Oct 31 14:16:46 ezcool kernel: INFO: task nspr-2:1007 blocked for more than 120 seconds.
Oct 31 14:16:46 ezcool kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Oct 31 14:16:46 ezcool kernel: nspr-2 D 0000000000000246 0 1007 1 0x00000000
Oct 31 14:16:46 ezcool kernel: ffff8803d67b9d68 0000000000000082 ffff8803d65b0810 ffff8803d67b9fd8
Oct 31 14:16:46 ezcool kernel: ffff8803d67b9fd8 ffff8803d67b9fd8 ffff8804194a58b0 ffff8803d65b0810
Oct 31 14:16:46 ezcool kernel: ffff880300000041 ffffffff8119df46 ffff88042fffdb08 0000000000000001
Oct 31 14:16:46 ezcool kernel: Call Trace:
Oct 31 14:16:46 ezcool kernel: [<ffffffff8119df46>] ? mntput+0x26/0x40
Oct 31 14:16:46 ezcool kernel: [<ffffffff811251cc>] ? __alloc_pages_nodemask+0x16c/0x960
Oct 31 14:16:46 ezcool kernel: [<ffffffff81491a09>] schedule+0x29/0x70
Oct 31 14:16:46 ezcool kernel: [<ffffffff81491cd7>] schedule_preempt_disabled+0x27/0x40
Oct 31 14:16:46 ezcool kernel: [<ffffffff81490368>] __mutex_lock_slowpath+0x148/0x340
Oct 31 14:16:46 ezcool kernel: [<ffffffff81490576>] mutex_lock+0x16/0x30
Oct 31 14:16:46 ezcool kernel: [<ffffffffa001cbfb>] show_product+0x2b/0x60 [usbcore]
Oct 31 14:16:46 ezcool kernel: [<ffffffff8132cc90>] dev_attr_show+0x20/0x60
Oct 31 14:16:46 ezcool kernel: [<ffffffff8112146e>] ? __get_free_pages+0xe/0x50
Oct 31 14:16:46 ezcool kernel: [<ffffffff811ef969>] sysfs_read_file+0xa9/0x190
Oct 31 14:16:46 ezcool kernel: [<ffffffff8117f785>] vfs_read+0xa5/0x180
Oct 31 14:16:46 ezcool kernel: [<ffffffff8117f8aa>] sys_read+0x4a/0xa0
Oct 31 14:16:46 ezcool kernel: [<ffffffff81499ded>] system_call_fastpath+0x1a/0x1f
Any ideas?

Satellite M-series does not start correctly

Hello,
I have the following problem: suddenly (don't know why, nothing changed) Satellite notebook shows black white screen with about the following:
(sorry, translated from german):
windows did not start correctly... due to software or hardware change.. pls choose last functional configuration if mistake was due to power shut down...
But this does not work, also all other options (start windows as normal, start in safe mode...did not work.
No idea what happenend !
Problem:
Actually moved to another country and forgot or lost recovery CD ! already contacted Toshiba for new one but maybe anyway somebody can help?

Hmm. Stupid situation. If possible try to obtain Microsoft WXP installations CD to see if you can start installations procedure properly and if you can use repair option too.
It is not easy to say what is wrong there but I just hope there is no problem with HDD. Try to use original recovery disc.

X86: Solaris does not boot correctly?

I have installed Solaris on a second hard disk.
When I boot my computer on the second hard disk, I get the Solaris 10 emergency booting system which tries to find out on which hard disk I would like to boot Solaris 10.
Is there a possiblity to save my settings once for all time?
Because on every time I boot, I got the Solaris emergency boot manager to rechoose the disk on which I should boot.

Since a similar thing happens after other updates, it probably is not directly related to "uninstalling google desktop." Does the same thing sometimes happen when you do a regular restart (with no update or uninstall)?
You can try doing a SMU (power management) reset. Before you do that, reset PRAM.
http://support.apple.com/kb/HT1379
If that does not help, follow this procedure precisely to reset the SMU
http://support.apple.com/kb/HT1767
When you reconnect the power cord, if you were using an power strip of some kind (especially if it's old or overcrowded), try connecting it directly to a wall outlet by itself (at least initially). Start it up with only the power cord connected, then (if it starts up normally), add only standard USB keyboard and mouse. Use it that way for a while to see if there's improvement. If it's better, add your other peripheral devices back, one at a time, to see if the problem returns.

Satellite L305D-S5934 does not boot - blank screen

I have a problem with a 2 year old satellite l305d-s5934.
On switching on, the power light comes on but the hard drive light does not and the screen stays blank.
I have tried removing the battery and restarting without it after pressing power button, but nothing changes.
Any advice on fixing the problem would be welcome.
Thanks

Hi
Remove battery, disconnect the AC adaptor and leave the notebook disconnected for a longer period of time. After that connect both parts can try to power up the unit once again
If this does not help, check the RAM. Remove the single module and test both slots using each module.
Of course it could be possible that both modules are faulty and this procedure would not help you.
In worst case the motherboard might be affected in such case only mobo replacement would be helpful.

Satellite C850-1NU does not boot Win 8.1 - Error Code 0xc0000098

Windows 8.1 will not boot
Laptop is *Toshiba Satellite C850 1NU*, as from Saturday it will not boot up!
*Error states "The boot configuration Data File doesn't contain valid information for an operating system.*
*File:\ BCD*
*Error Code 0xc0000098*
I have transferred recovery tools from another laptop to a USB stick and then enter bios of the Toshiba Laptop to make the USB drive to boot first.
It then comes up with the recovery tools.
I clicked on "Refresh your pc" it then reports "The drive where Windows is installed is locked. Unlock the drive and try again".
I clicked on "Reset your pc" it then reports "Unable to reset your pc. A required drive partition is missing".
I have also tried "Automatic Repair" and it reports "Repair couldn't repair your PC".
I am at a loss as to get my sons laptop up and running again. Advice would be much appreciated. Thank you.

Further to my question, *I have now resolved the issue.*
Thanks to phanlon7 on this link
[http://answers.microsoft.com/en-us/windows/forum/windows_8-system/windows-crash-refresh-hard-drive-locked-unlock/a6bb04ff-5dba-4e10-a849-644cd0851bc6?page=2&rtAction=1390385080363]
I used a usb stick and copied recovery from another windows 8 laptop.

Satellite M30-107 does not boot correctly after Recovery disk usage

Similar Messages

Maybe you are looking for