Satellite M50D-A : USB 3.0 devices not working in USB 3.0 ports

I can use 2.0 devices in the 3.0 ports fine, but my 3.0 device Flash Voyager USB3 8GB will not work. It connects then disconnects once, not showing up in device manager at all.
I've tried installing the USB driver off this site version 2.0.10.273-130101a for my model. That made no difference.
Install system Windows 8.1
Any ideas? Thanks.

The Voyager USB stick is manufactured by Corsair
I found in Corsair forum some threads and complaints about the troubles connecting the Voyager USB3.0 stick to USB 3.0 ports. Here the link the Corsair threads:
http://forum.corsair.com/v3/showthread.php?t=115891
http://forum.corsair.com/v3/showthread.php?t=111945
It looks like there are some compatibility problems between the USB controller (from AMD but _not_ Intel) and this USB stick.
One of the solutions could be the usage of other USB 3.0 flash memory sticks which are supported by AMD chipset.
You could also try to update the driver manually. You will need to check firstly the chipsets specs and name. To do that, I recommend you to install some kind of hardware diagnostic software (Everest Home Edit or Sandra Sisoft).
Then you could check on AMD page if an update for this chipset is available.

Similar Messages

MacBook Pro Retina USB 2.0 devices not working in right side USB port

4 days ago I bought MacBook Pro Retina 15".
When I plug USB 2.0 device to right side USB port, it does not work. OSX does not recognize it, iPhone does not charge, and so.
When I plug the same USB 2.0 device to left side USB port, it works.
When I plug USB 3.0 device to left or right side USB ports, it works without a problem.
Does anyone have this same issue? How did you resolve it?

I have a similar issue with a 13" Retina. Both my ports work OK for most USB devices but the right one won't work with a USB external HD (Time Machine backup). Very consistant.

Ipod 7th generation. bought it 3 days ago. no problem then but now won't turn on. I keep getting a usb device not recognized (and i keep changing ports to no avail). what to do?

ipod 7th generation. bought it 3 days ago. no problem then but now won't turn on. I keep getting a usb device not recognized (and i keep changing ports to no avail). what to do?

wish i can rmber how mine was fixed i think i just waited tried again and likr magic it worked again left itunplugged, i was like you recently boughtand it happened to me, now i have another diffrent promblem with it.

Can't mount external HDD? "usb 1-1: Device not accepting address"

I just bought a Medion HDDRIVE2GO (Full Speed) from Aldi, and at first when I plugged it in, everything went fine (well, I thought so). Appearently it had some errors with HAL not being able to read the HDD (error name="(unset)").
I gave it a reboot, and now it does not work at all! In dmesg, I have this output (the bottom is the most important I guess)
[dell@linuxnas ~]$ dmesg
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.33-ARCH (thomas@evey) (gcc version 4.5.0 (GCC) ) #1 SMP PREEMPT Thu May 13 12:06:25 CEST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffe2800 (usable)
BIOS-e820: 000000001ffe2800 - 0000000020000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
last_pfn = 0x1ffe2 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-EFFFF uncachable
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FE0000000 write-back
1 base 0FEDA0000 mask FFFFE0000 write-combining
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 0000000000002000 - 0000000000010000 (usable) ==> (reserved)
Scanning 1 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000002000 (usable)
modified: 0000000000002000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 0000000000100000 - 000000001ffe2800 (usable)
modified: 000000001ffe2800 - 0000000020000000 (reserved)
modified: 00000000feda0000 - 00000000fee00000 (reserved)
modified: 00000000ffb80000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-000000001ffe2000
0000000000 - 0000400000 page 4k
0000400000 - 001fc00000 page 2M
001fc00000 - 001ffe2000 page 4k
kernel direct mapping tables up to 1ffe2000 @ 15000-1a000
RAMDISK: 1fe3b000 - 1ffd2770
ACPI: RSDP 000fde50 00014 (v00 DELL )
ACPI: RSDT 000fde64 00028 (v01 DELL CPi R 27D4010C ASL 00000061)
ACPI: FACP 000fde90 00074 (v01 DELL CPi R 27D4010C ASL 00000061)
ACPI: DSDT fffe4000 0319C (v01 INT430 SYSFexxx 00001001 MSFT 0100000E)
ACPI: FACS 1ffff800 00040
0MB HIGHMEM available.
511MB LOWMEM available.
mapped low ram: 0 - 1ffe2000
low ram: 0 - 1ffe2000
node 0 low ram: 00000000 - 1ffe2000
node 0 bootmap 00016000 - 0001a000
(10 early reservations) ==> bootmem [0000000000 - 001ffe2000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0001000000 - 0001550444] TEXT DATA BSS ==> [0001000000 - 0001550444]
#3 [001fe3b000 - 001ffd2770] RAMDISK ==> [001fe3b000 - 001ffd2770]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [0001551000 - 0001557198] BRK ==> [0001551000 - 0001557198]
#6 [0000010000 - 0000011000] TRAMPOLINE ==> [0000010000 - 0000011000]
#7 [0000011000 - 0000015000] ACPI WAKEUP ==> [0000011000 - 0000015000]
#8 [0000015000 - 0000016000] PGTABLE ==> [0000015000 - 0000016000]
#9 [0000016000 - 000001a000] BOOTMAP ==> [0000016000 - 000001a000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x0001ffe2
HighMem 0x0001ffe2 -> 0x0001ffe2
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000000 -> 0x00000002
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0001ffe2
On node 0 totalpages: 130931
free_area_init_node: node 0, pgdat c13f9880, node_mem_map c1559000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3953 pages, LIFO batch:0
Normal zone: 992 pages used for memmap
Normal zone: 125954 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
SMP: Allowing 1 CPUs, 0 hotplug CPUs
Local APIC disabled by BIOS -- you can enable it with "lapic"
APIC: disable apic facility
APIC: switched to apic NOOP
nr_irqs_gsi: 16
PM: Registered nosave memory: 0000000000002000 - 0000000000010000
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
Allocating PCI resources starting at 20000000 (gap: 20000000:deda0000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Embedded 14 pages/cpu @c1c00000 s34776 r0 d22568 u4194304
pcpu-alloc: s34776 r0 d22568 u4194304 alloc=1*4194304
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129907
Kernel command line: root=/dev/disk/by-uuid/5501fa6d-1664-41e3-ac30-9a475cc6843d ro vga=773
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
allocated 2620840 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Initializing HighMem for node 0 (00000000:00000000)
Memory: 509220k/524168k available (2895k kernel code, 14260k reserved, 1208k data, 408k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff1e000 - 0xfffff000 ( 900 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe07e2000 - 0xff7fe000 ( 496 MB)
lowmem : 0xc0000000 - 0xdffe2000 ( 511 MB)
.init : 0xc1403000 - 0xc1469000 ( 408 kB)
.data : 0xc12d3f1e - 0xc14022e0 (1208 kB)
.text : 0xc1000000 - 0xc12d3f1e (2895 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:512
Console: colour dummy device 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1993.528 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3988.18 BogoMIPS (lpj=6645093)
Security Framework initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU0: Hyper-Threading is disabled
mce: CPU supports 4 MCE banks
Performance Events: no PMU driver, software events only.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20091214
ACPI: setting ELCR to 0200 (from 0800)
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (3988.18 BogoMIPS).
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbfee, last bus=2
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: Power Resource [PADA] (on)
ACPI: ACPI Dock Station Driver: 1 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci_root PNP0A03:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x20000000-0xfed9ffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xfee00000-0xffb7ffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0xffc00000-0xfff7ffff] (ignored)
pci 0000:00:00.0: reg 10: [mem 0xe8000000-0xebffffff pref]
pci 0000:00:1d.0: reg 20: [io 0xbf80-0xbf9f]
pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x0880-0x08bf] claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10: [io 0x01f0-0x01f7]
pci 0000:00:1f.1: reg 14: [io 0x03f4-0x03f7]
pci 0000:00:1f.1: reg 18: [io 0x0170-0x0177]
pci 0000:00:1f.1: reg 1c: [io 0x0374-0x0377]
pci 0000:00:1f.1: reg 20: [io 0xbfa0-0xbfaf]
pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
pci 0000:00:1f.5: reg 10: [io 0xd800-0xd8ff]
pci 0000:00:1f.5: reg 14: [io 0xdc80-0xdcbf]
pci 0000:00:1f.6: reg 10: [io 0xd400-0xd4ff]
pci 0000:00:1f.6: reg 14: [io 0xdc00-0xdc7f]
pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
pci 0000:01:00.0: reg 14: [io 0xc000-0xc0ff]
pci 0000:01:00.0: reg 18: [mem 0xfcff0000-0xfcffffff]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:01.0: bridge window [mem 0xfc000000-0xfdffffff]
pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe7ffffff pref]
pci 0000:02:00.0: reg 10: [io 0xec80-0xecff]
pci 0000:02:00.0: reg 14: [mem 0xf8fffc00-0xf8fffc7f]
pci 0000:02:00.0: reg 30: [mem 0xf9000000-0xf901ffff pref]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:01.0: reg 10: [mem 0x00000000-0x00000fff]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:02:01.1: reg 10: [mem 0x00000000-0x00000fff]
pci 0000:02:01.1: supports D1 D2
pci 0000:02:01.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:01.1: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 02-10] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xe000-0xffff]
pci 0000:00:1e.0: bridge window [mem 0xf4000000-0xfbffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:02: disabling [io 0x0800-0x0805] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f]
pnp 00:02: disabling [io 0x0808-0x080f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f]
pnp 00:03: disabling [io 0x0806-0x0807] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f]
pnp 00:03: disabling [io 0x0810-0x085f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f]
pnp 00:03: disabling [io 0x0860-0x087f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f]
pnp 00:04: disabling [io 0xf000-0xf0fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf100-0xf1fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf200-0xf2fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf400-0xf4fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf500-0xf5fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf600-0xf6fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf800-0xf8fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xf900-0xf9fe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xfa00-0xfafe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xfc00-0xfcfe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xfd00-0xfdfe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [io 0xfe00-0xfefe] because it overlaps 0000:00:1e.0 BAR 13 [io 0xe000-0xffff]
pnp 00:04: disabling [mem 0xfa000000-0xfbffffff] because it overlaps 0000:00:1e.0 BAR 14 [mem 0xf4000000-0xfbffffff]
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0x00000000-0x0009fbff] could not be reserved
system 00:00: [mem 0x0009fc00-0x0009ffff] could not be reserved
system 00:00: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:00: [mem 0x00100000-0x1ffeffff] could not be reserved
system 00:00: [mem 0x1fff0000-0x1fffffff] has been reserved
system 00:00: [mem 0xfeda0000-0xfedfffff] has been reserved
system 00:00: [mem 0xfff80000-0xffffffff] has been reserved
system 00:02: [io 0x04d0-0x04d1] has been reserved
system 00:03: [io 0x0880-0x08bf] has been reserved
system 00:03: [io 0x08c0-0x08df] has been reserved
system 00:03: [io 0x08e0-0x08ff] has been reserved
system 00:09: [io 0x0900-0x091f] has been reserved
system 00:09: [io 0x03f0-0x03f1] has been reserved
system 00:0f: [io 0xbf40-0xbf5f] has been reserved
system 00:0f: [io 0xbf20-0xbf3f] has been reserved
system 00:10: [mem 0xfebffc00-0xfebfffff] has been reserved
pci 0000:00:1e.0: BAR 15: assigned [mem 0x20000000-0x27ffffff pref]
pci 0000:00:1f.1: BAR 5: assigned [mem 0x28000000-0x280003ff]
pci 0000:00:1f.1: BAR 5: set to [mem 0x28000000-0x280003ff] (PCI address [0x28000000-0x280003ff]
pci 0000:01:00.0: BAR 6: assigned [mem 0xfc000000-0xfc01ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:01.0: bridge window [mem 0xfc000000-0xfdffffff]
pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe7ffffff pref]
pci 0000:02:01.0: BAR 15: assigned [mem 0x20000000-0x23ffffff pref]
pci 0000:02:01.0: BAR 16: assigned [mem 0xf4000000-0xf7ffffff]
pci 0000:02:01.1: BAR 15: assigned [mem 0x24000000-0x27ffffff pref]
pci 0000:02:01.1: BAR 16: assigned [mem 0x2c000000-0x2fffffff]
pci 0000:02:01.0: BAR 0: assigned [mem 0xf8000000-0xf8000fff]
pci 0000:02:01.0: BAR 0: set to [mem 0xf8000000-0xf8000fff] (PCI address [0xf8000000-0xf8000fff]
pci 0000:02:01.1: BAR 0: assigned [mem 0xf8001000-0xf8001fff]
pci 0000:02:01.1: BAR 0: set to [mem 0xf8001000-0xf8001fff] (PCI address [0xf8001000-0xf8001fff]
pci 0000:02:01.0: BAR 13: assigned [io 0xe000-0xe0ff]
pci 0000:02:01.0: BAR 14: assigned [io 0xe400-0xe4ff]
pci 0000:02:01.1: BAR 13: assigned [io 0xe800-0xe8ff]
pci 0000:02:01.1: BAR 14: assigned [io 0xf000-0xf0ff]
pci 0000:02:01.0: CardBus bridge to [bus 03-06]
pci 0000:02:01.0: bridge window [io 0xe000-0xe0ff]
pci 0000:02:01.0: bridge window [io 0xe400-0xe4ff]
pci 0000:02:01.0: bridge window [mem 0x20000000-0x23ffffff pref]
pci 0000:02:01.0: bridge window [mem 0xf4000000-0xf7ffffff]
pci 0000:02:01.1: CardBus bridge to [bus 07-0a]
pci 0000:02:01.1: bridge window [io 0xe800-0xe8ff]
pci 0000:02:01.1: bridge window [io 0xf000-0xf0ff]
pci 0000:02:01.1: bridge window [mem 0x24000000-0x27ffffff pref]
pci 0000:02:01.1: bridge window [mem 0x2c000000-0x2fffffff]
pci 0000:00:1e.0: PCI bridge to [bus 02-10]
pci 0000:00:1e.0: bridge window [io 0xe000-0xffff]
pci 0000:00:1e.0: bridge window [mem 0xf4000000-0xfbffffff]
pci 0000:00:1e.0: bridge window [mem 0x20000000-0x27ffffff pref]
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:02:01.0: enabling device (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:02:01.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
pci 0000:02:01.1: enabling device (0000 -> 0003)
pci 0000:02:01.1: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:01: resource 1 [mem 0xfc000000-0xfdffffff]
pci_bus 0000:01: resource 2 [mem 0xe0000000-0xe7ffffff pref]
pci_bus 0000:02: resource 0 [io 0xe000-0xffff]
pci_bus 0000:02: resource 1 [mem 0xf4000000-0xfbffffff]
pci_bus 0000:02: resource 2 [mem 0x20000000-0x27ffffff pref]
pci_bus 0000:02: resource 3 [io 0x0000-0xffff]
pci_bus 0000:02: resource 4 [mem 0x00000000-0xffffffff]
pci_bus 0000:03: resource 0 [io 0xe000-0xe0ff]
pci_bus 0000:03: resource 1 [io 0xe400-0xe4ff]
pci_bus 0000:03: resource 2 [mem 0x20000000-0x23ffffff pref]
pci_bus 0000:03: resource 3 [mem 0xf4000000-0xf7ffffff]
pci_bus 0000:07: resource 0 [io 0xe800-0xe8ff]
pci_bus 0000:07: resource 1 [io 0xf000-0xf0ff]
pci_bus 0000:07: resource 2 [mem 0x24000000-0x27ffffff pref]
pci_bus 0000:07: resource 3 [mem 0x2c000000-0x2fffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
pci 0000:01:00.0: Boot video device
PCI: CLS 32 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 1629k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1274299821.609:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 998
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xe0000000, mapped to 0xe0800000, using 1536k, total 32768k
vesafb: mode is 1024x768x8, linelength=1024, pages=41
vesafb: protected mode interface info at c000:549f
vesafb: pmi: set display start = c00c5533, set palette = c00c557f
vesafb: pmi: ports = c010 c016 c054 c038 c03c c05c c000 c004 c0b0 c0b2 c0b4
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
serial 0000:00:1f.6: PCI INT B disabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
PM: Resume from disk failed.
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 408k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
Floppy drive(s): fd0 is 1.44M
SCSI subsystem initialized
FDC 0 is a post-1991 82077
libata version 3.00 loaded.
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
ata2.01: NODEV after polling detection
ata1.00: ATA-6: HTS548040M9AT00, MG2OA5EA, max UDMA/100
ata1.00: 78140160 sectors, multi 8: LBA48
ata2.00: ATAPI: HL-DT-STDVD-ROM GDR8081N, 0108, max MWDMA2
ata2.00: configured for MWDMA2
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA HTS548040M9AT00 MG2O PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8081N 0108 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:sr0: scsi3-mmc drive: 10x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sda1 sda2 sda3 sda4
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: [sda] Attached SCSI disk
EXT4-fs (sda3): mounted filesystem with ordered data mode
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, 114 bytes nvram
udev: starting version 151
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
intel_rng: FWH not detected
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.103
Marking TSC unstable due to TSC halts in idle
input: PC Speaker as /devices/platform/pcspkr/input/input2
ACPI: AC Adapter [AC] (on-line)
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
ACPI: Power Button [PBTN]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
ACPI: Sleep Button [SBTN]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Switching to clocksource acpi_pm
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
parport_pc 00:0e: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
iTCO_vendor_support: vendor-support=0
agpgart-intel 0000:00:00.0: Intel 845G Chipset
lp: driver loaded but no devices found
lp0: using parport0 (interrupt-driven).
agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
ppdev: user-space parallel port driver
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM] (57 C)
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x9b4cb1, caps: 0x884793/0x0
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
yenta_cardbus 0000:02:01.0: CardBus bridge found [1028:012a]
yenta_cardbus 0000:02:01.0: Using CSCINT to route CSC interrupts to PCI
yenta_cardbus 0000:02:01.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:01.0: TI: mfunc 0x01261222, devctl 0x64
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH3-M TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:15/LNXVIDEO:00/input/input7
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
yenta_cardbus 0000:02:01.0: ISA IRQ mask 0x0418, PCI irq 11
yenta_cardbus 0000:02:01.0: Socket status: 30000006
yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xe000-0xffff: clean.
yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
3c59x 0000:02:00.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
3c59x: Donald Becker and others.
0000:02:00.0: 3Com PCI 3c905C Tornado at e0c6ac00.
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
Intel ICH 0000:00:1f.5: setting latency timer to 64
yenta_cardbus 0000:02:01.1: CardBus bridge found [1028:012a]
yenta_cardbus 0000:02:01.1: Using CSCINT to route CSC interrupts to PCI
yenta_cardbus 0000:02:01.1: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:01.1: TI: mfunc 0x01261222, devctl 0x64
usb 1-1: new full speed USB device using uhci_hcd and address 2
[drm] Initialized drm 1.1.0 20060810
yenta_cardbus 0000:02:01.1: ISA IRQ mask 0x0418, PCI irq 11
yenta_cardbus 0000:02:01.1: Socket status: 30000006
yenta_cardbus 0000:02:01.1: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xe000-0xffff: clean.
yenta_cardbus 0000:02:01.1: pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
yenta_cardbus 0000:02:01.1: pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff
usb 1-1: device descriptor read/64, error -71
usb 1-1: device descriptor read/64, error -71
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
radeon 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] radeon: Initializing kernel modesetting.
[drm] register mmio base: 0xFCFF0000
[drm] register mmio size: 65536
[drm] GPU reset succeed (RBBM_STATUS=0x00000140)
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
radeon 0000:01:00.0: putting AGP V2 device into 4x mode
[drm] radeon: VRAM 64M
[drm] radeon: VRAM from 0x00000000 to 0x03FFFFFF
[drm] radeon: GTT 64M
[drm] radeon: GTT from 0xE8000000 to 0xEBFFFFFF
[drm] radeon: irq initialized.
[drm] Detected VRAM RAM=64M, BAR=128M
[drm] RAM width 64bits DDR
[TTM] Zone kernel: Available graphics memory: 255756 kiB.
[drm] radeon: 32M of VRAM memory ready
[drm] radeon: 64M of GTT memory ready.
[drm] radeon: cp idle (0x00008383)
[drm] Loading R100 Microcode
platform radeon_cp.0: firmware: requesting radeon/R100_cp.bin
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
usb 1-1: new full speed USB device using uhci_hcd and address 3
clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[drm] radeon: ring at 0x00000000E8000000
[drm] ring test succeeded in 1 usecs
intel8x0_measure_ac97_clock: measured 52675 usecs (2532 samples)
intel8x0: clocking to 48000
[drm] radeon: ib pool ready.
[drm] ib test succeeded in 0 usecs
[drm] Panel ID String: QDI141X1LH03
[drm] Panel Size 1024x768
[drm] Default TV standard: NTSC
[drm] 27.000000000 MHz TV ref clk
[drm] No TV DAC info found in BIOS
[drm] Default TV standard: NTSC
[drm] 27.000000000 MHz TV ref clk
[drm] Radeon Display Connectors
[drm] Connector 0:
[drm] VGA
[drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[drm] Encoders:
[drm] CRT1: INTERNAL_DAC1
[drm] Connector 1:
[drm] LVDS
[drm] Encoders:
[drm] LCD1: INTERNAL_LVDS
[drm] Connector 2:
[drm] S-video
[drm] Encoders:
[drm] TV1: INTERNAL_DAC2
usb 1-1: device descriptor read/64, error -71
[drm] fb mappable at 0xE0040000
[drm] vram apper at 0xE0000000
[drm] size 786432
[drm] fb depth is 8
[drm] pitch is 1024
fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
Console: switching to colour dummy device 80x25
Console: switching to colour frame buffer device 128x48
fb0: radeondrmfb frame buffer device
registered panic notifier
[drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
usb 1-1: device descriptor read/64, error -71
usb 1-1: new full speed USB device using uhci_hcd and address 4
usb 1-1: device not accepting address 4, error -71
EXT4-fs (sda4): mounted filesystem with ordered data mode
usb 1-1: new full speed USB device using uhci_hcd and address 5
Adding 265064k swap on /dev/sda2. Priority:-1 extents:1 across:265064k
psmouse serio2: ID: 10 00 64
usb 1-1: device not accepting address 5, error -71
hub 1-0:1.0: unable to enumerate USB device on port 1
eth0: setting full-duplex.
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/serio2/input/input8
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
lspci (Is this useable info?)
[dell@linuxnas ~]$ lspci
00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]
02:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
02:01.0 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
02:01.1 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller

I found this post on linux forums which say It's a HAL related problem.
"rmmod ehci_hcd" made it work for some of these guys Which one of them explains It's a data speed issue. Cables.., 2.0 1.0, that sort of things. Read it, I bet you'll get more out of it, It's old though.
Try removing the module, plugging the drive, check dmesg, and mount manually.
Last edited by Ekimino (2010-05-20 01:23:54)

Dual-Boot; Restart and boot other o/s USB devices not working

I have issue with my msi z97-g43 mobo and Windows dual o/s PC.
Booting with win-8.1, USB devices working very well.Restaring windows 8.1 have NOT any issue.
After shutdown & start PC, choosing to boot windows 7 on bootmanager, USB devices not working in Win-7.
System no hang or occur any error/BSOD message.All startup programs run as normal.
I tried to re-plug usb devices but notting happens... Still not working
But after the win-8.1 shutdown, if i switch off PSU power button, watting ~1 munute for discharge.
After power up PC and boot with windows 7 all usb devices works normaly.
I checked all internal connections. 2 times disassembly all hardware and re-built system, nothing changed.All windows updates and latest drivers installed.
I'm sure other H/W is OK, but I thnik this mobo have a fault.

Thank you for reply.My PC system specs:
CPU:    Intel Pentium G3258 3.2ghz
Board:    MSI Z97-G43 /Bios: Ver. V17.7
MEM:    G.Skill Ripjaws 2x4gb DDR3-1600mhz cl9 1.5v F3-12800CL9-4GBRL
VGA:    Sapphire AMD Redeon HD6670
CASE:    Zalman z3 plus white (5x 120mm fan)
PSU:    Thermaltake Litepower 500w (12v1+12v2=36amp)
HDD-1:    Seagate 1TB ST1000DM003 /HDD-2: Seagate 2TB ST2000DM001
COOLER:    Akasa 92mm PWM Blue Led
OC:    CPU:Default /MEM: X.M.P mode=1600mhz 9-9-9-24-2t 1.5v
O/S:    Win7 x64 PRO + Win8.1 x64 PRO (Genuine)
All hdd's have MBR based partition table.Windows 7 & 8.1 installed in non-efi mode.In BIOS Boot sequence is setting up to non-efi Boot(system) drive as primary.
Before I suspect maybe have a short circuit to pcb or similar thing cause this issue.I take out all parts outside the chassis, and ran this system on the antistatic bag and box.Nothing has been changed.
I have Cooler Master Devastator(MB24 + MS2k) USB keyb+mouse set and tplink wn722n usb wireless dongle.
I have one more pc,based on AMD 970+SB950 chipset mainboard and AMD CPU.I exchange all parts to this amd mainbaord and tested for faulted hardware.All intel system H/W's is ok.All works great
Dual boot works perfectly.Not needs to switch off psu/power back and run system again.
I think msi z97-g43 mainbıoard have a problem.

Usb composite device is an older usb device and might not work in USB 3

I recently bought one Lenovo Yoga 2 11 laptop running Windows 8.1 (64 bit).
When I try to connect my old Brother MFC-3240C printer using USB (2.0), it doesn’t work.
Below are the steps performed:
Connected the printer to USB 2.0 port on laptop (on the right side). Automatically installed the printer driver (no exclamation mark beside printer icon)
When the printer didn’t print, I tried to use troubleshoot as below:
Control Panel->Hardware and Sound->Devices and Printers->Right Click on Printer Icon->Troubleshoot.
It came up with USB composite device is an older usb device and might not work in USB 3.0
Removed the printer and re-installed the driver. It is all the same.
Any help will be greatly appreciated.
FYI – the same printer works fine with my older laptops running Windows 7.

Already checked Brothers website for the printer drivre for Windows 8.1 (64 bit).
It says ... The built-in driver is already included with Windows® Operating System or is available through Windows® update.
So, installed the default driver for the printer that is available with Windows 8.1.
Even connected the printer with USB 3.0 port on the laptop, but it is all the same.

I have an Ipod Touch, it appears inactive and says conect to Itunes. When I connect it to the PC, the PC says "USB device not working". How can do to solve this problem.

I have an Ipod Touch, it appears inactive and says "connect to Itunes". When I connect to the PC, the PC says "USB device not working". How could do to solve this problem?

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
or
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

HT5634 I already install bootcamp 5 on my Macbook Pro MD101 (Mid 2012). But when I plug the USB, my Mac can not recognize the USB or any Storage device. Pls help

I already install Bootcamp 5 on my Macbook Pro MD101 (Mid 2012) but when I plug the USB, my Mac can not recognize the USB, also any storage device. Pls help !!! I am using Window 7

I ran an Apple Hardware Test, says ''No trouble found'.

Iphone 4S will not charge, error that USB device not working, found any suggestions?

iphone 4S will not charge, error that USB device not working, found any suggestions?

Hello Chambless,
The troubleshooting steps below can help get your iPhone to charge.
If your battery doesn't charge, or if your device shows a low-battery image, black screen, or "accessory not supported" alert, follow these steps.
Inspect the connector at the bottom of the phone:
Make sure that there are no bent pins in the connector.
Make sure that the connector is free from debris.
If there are bent pins or debris, please contact Apple Support.
Otherwise, continue troubleshooting.
Make sure that the outlet you're using works.
Make sure that the Apple USB cable and Apple USB power adapter work.
Plug the device in to power and let it charge for up to 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
If the device still exhibits an issue, try turning your device off and then on again while connected to power.
If the issue is persists, please contact Apple Support.
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
Cheers,
Allen

Z87-G45 USB Mass Storage & other devices not working (except keyboard/mouse)

My Z87-G45 died on me last month in warranty so I received a replacement one.
Unfortunatly I'm experiencing mayor USB issues.
- In Bios mode, no USB mass storage devices are detected (usb stick/disk). USB keyboard and mouse work fine
- In Windows no USB device except for the keyboard and mouse are detected.
- Can't see USB Mass Storage Device driver in the USB controllers list
Installed all latest drivers + CMOS CLEAR just in case. Results stay the same.
I assume it's best that I return the motherboard?
Kind regards
Frederick

Quote from: frederick.dhont on Today at 02:43:46
All drivers are already all up-to-date
I also want to stress that USB mass storage devices are not detected in BIOS, NOR as bootable USB device. So I can't upgrade BIOS even if I wanted to.
have you done >>Clear CMOS Guide<< with power cord removed?
have you tested with mainboard out of PC case placed over wooden table?

In my macbook pro hdmi, usb & SD card reader not working

In my macbook pro hdmi, usb & sc card reader not working.
i have tried the SRM reset done, till not working started.
Could you please resolve this problem,

Welcome to Apple Support Communities
Simply take it to an Apple Store or reseller if it's in warranty. Your Mac will be repaired or replaced for free because it looks a hardware problem rather than a software issue.
If it's not in warranty, hold Command and R keys while your MacBook is starting up, and reinstall OS X. If it doesn't work, you can't do much more to solve the problem

I have purchased new iphone 3gs, its usb cable and charger not working.When I plugged in usb cable to my laptop it says"usb power hub exceeded". When I use another cable I have, it works fine.But the original one not working.Any help?

I have purchased new iphone 3gs, its usb cable and charger not working.When I plugged in usb cable to my laptop it says"usb power hub exceeded". When I use another cable I have, it works fine.But the original one not working.Any help?

Are you connecting your iPhone directly to your PC or to a USB hub?

Streaming Audio through Iphone 5 to desktop or laptop using bluetooth preinstalled on all devices not working. Help!!!.

Streaming Audio through Iphone 5 to desktop or laptop using bluetooth preinstalled on all devices not working. Help!!!. Does anybody else have this problem?. Or does anybody have a solution to the problem. If So please help me its driving me demented seriously concidering to go to android for that sort of stuff cause of the dame restrictions on apple devices!

iOS devices do not pair with computers, as data transfer over bluetooth is not supported.
Computers are not airplay compatible unless you have downloaded an app to make them so.
User to user forum, so I don't care if you switch to android or any other threats you make.

My laptop biometric device not working.

HI,
I am facing one problem with my hp pavilion dv6 6160se biometric device not working and i also lost my recovery deta. kindly provide me the solution.
and my system also very slow how can i make it fast.
m. asif

Hi there @Sweeto684
Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
I understand that your fingerprint reader is not working and that your system is running very slow, but please clarify what you mean by saying you lost the recovery data. Are you referring to the factory recovery image stored on your system, or are you meaning something else?
I am happy to help you with all of this, but need to know more before I can make some useful recommendations. I want to avoid having you do something that could cause a problem with something else, until I know what problem really is.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

In My IPhone the sound device not working properly. I can here the sound through head set only.kindly send an idea ti solve this problems

In My IPhone the sound device not working properly. I can here the sound through head set only.kindly send an idea ti solve this problems

Hello. I sent my WRT1900AC V1 to Linksys four days ago (Monday) via UPS with a RMA. Linksys paid the shipping and everything. The router is still in route, and it should arrive to their offices tomorrow. Once they receive the WRT1900 AC V1, they are going to send me an EA8500 as a replacement. But I have been reading the comments about the EA8500 here in the forum and it seems to have the same problems. I guess the firmware is extremely flawed in both routers (maybe it is almost the same code?). Anyway, I will try the EA8500 and I hope it works. I bought a temporary router from Walmart and I paid $35 for it. It is a Belink N600 DB. I can't believe that a $35 router is working a lot, lot, lot better than my previous $250 WRT1900AC router. Unbelievable. If the EA8500 doesn't work, I'm going to try and get my money back from Linksys, or contact The Consumerist or someone to get my money back and get a Nighthawk instead.

Satellite M50D-A : USB 3.0 devices not working in USB 3.0 ports

Similar Messages

Maybe you are looking for