Satellite M60: Need parallel port to connect Iomega Zip drive

Hi guys,
I have a Satellite M60 and I want to transfer some files from my Iomega Zip drive .
My notebook does not has a paraller port, so I bought a converter in order to make it work but there was no result.
Does anyone of you knows how to resolve the problem and finaly attach my ZIP driver to my Satellite in order to transfer the files?
Do I need another converter?
If yes, then which one? Or, do I have to buy a PCI card with a paraller port?
Any answer will be appraciated
thanx

Hi
I never used an USB-to-parallel converter but an USB-to-serial port converter and I made very bad experience witch such parts.
As far as I know such adapters dont work properly.
Therefore your suggestion is not bad to use the PCMCIA card with a parallel port.
Check firstly in your user manual which cards are compatible and then you could try to use such card.
I think this would be the best solution to connect your Iomega Zip drive to the M60 notebook.
Regards

Similar Messages

Problem connecting PB 1400 to Iomega Zip Drive

I am having difficulty connecting an iomega zip drive to my pb1400. I have the adapter that goes into the 1400 connected to wide scsi-type plugs that are mated and then into smaller scsi on zip. But when I power on, I get a flashing "2" enclosed in a diamond. I may have some kind of termination problem. Not sure. Any suggestions? TTommy

TTommy,
It sounds like you have a SCSI Disk Adapter for SCSI Disk Mode instead of the SCSI System Adapter for adding external SCSI Devices. The HDI-30 SCSI Disk Adapter will have 30 pins or the adapter will have a small switch for 'disk' or 'system'. A standard HDI-30 SCSI System Adapter will have 29 pins; the 30th pin forces the computer into SCSI Disk Mode.
If you have the Zip 100 drive, make sure the termination switch on the back panel is turned 'ON'.
Here is a good article on SCSI devices; please read it carefully, especially the part where all devices must be powered off when making any changes to the SCSI chain.
http://support.apple.com/kb/TA21592?viewlocale=en_US

How to transfer photo files from Iomega Zip Drive cassette to my iMac?

1 GHz PowerPC G4
768 MB DDR SDRAM
external hard disk 500 GB
external hard disk 125 GB
Many years ago I stored/copied my photos onto a Iomega Zip Drive cassette. Subsequently I lost everything in a computer malfunction which Apple Store could not fix; they ultimately replaced my computer. The computer that I was using when I used the Iomega Zip Drive was a Mac Quadra, not an iMac. Unfortunately, I had not backed up anything so the only thing that I have from the time prior to the malfunction is what I have stored on these Zip Drive cassettes and on the hard drive of the iMac that malfunctioned and was replaced with a new iMac. The photos that I really want to get are those of my husband who has since passed away.
It has been so long that I used them or even looked at them that now I don't know how to get those photos onto my present iMac (and I am assuming that it is possible).
Would you be so kind as to tell me what to do to transfer my photos from the Iomega Zip Drive cassette? Thank you very much.
— Lorna in Southern California
http://web.mac.com/lorna6
17" flatscreen iMac, 1 GHz Power PC G4, 768 MB DDR SDRAM Mac OS X (10.4.7) LaCie external hard drive, 111 Gigabytes, iPhoto 6.0.4, Canoscan scanner

Lorna, I'm sorry to hear of your loss.
The easiest thing to do is to purchase an External USB Zip drive (link). As ZIP disks are now legacy technology ebay has a great many available which means they are pretty low cost. Simply connect the drive and insert the disk. The disk will mount on to the desktop.
Alternatively you could see if a local Internet café still has such as drive available and they will be able to burn the contents to CD for a few dollars.
Hope that helps.
mrtotes

Support for Iomega Zip drives?

Does OS 8 have built-in support for external Iomega Zip drives?
Does anyone know if OS 7.x does?

I don't know about System 7.5, but I have a PowerMac 6500/300 that came with both System 7.6.1 and an internal ZIP drive. I think you do need to download some drivers from Iomega to get it to work however. I do know that when I tried a clean install of OS 8 some years back, I couldn't use the ZIP drive. I think I also had to upgrade the ZIP drivers at some point, but I can't remember if it was when I upgraded to OS 8, applied the 8.1 patch, or upgraded to 8.5 and applied the 8.6 patch.
All I know is that you can use both the internal and the external ZIP drives with 7.6.1 if you download a driver from Iomega. Weather or not you can still do so is another issue. I could extract them from the RestoreCD, but it wouldn't have an installer.

Iomega Zip Drive

I have an external Iomega Zip drive with a USB connection that I was using with a PC. I plugged it into my Mac and it worked fine. Then, when I went back and plugged it into my PC it said the drive was unreadable. Is there any way to get the drive to be compatible with my PC again without destroying the files that are on it? Thank you.
Nate

Thank you for the response. The external zip drive AND disk were working with a PC before I plugged it into a Mac. Does the Mac reformat the disk and/or drive automatically when it is connected with USB thereby making it incompatible with a PC? If I reformat using the program you suggest, will the files currently on the disk get erased? Thanks for your help.

Iomega zip drive won't copy

After having a corrupted hard drive fixed and Os 10.2.8 reinstalled, I found that my Iomega Zip 100 drive wouldn't copy large folders (microsoft word). It would copy individual files and smaller folders. The error message I got was -50. I understand that this relates to bad zip discs.
I tried a new zip disc and also tried a different Iomega zip drive, with identical results. It seems that the problem lies with the computer, not the zip drive. I'd be grateful for any suggestions.

Apologies for the acronyms. HFS and HFS+ are Mac drive formats. Newer machines' drives must be HFS+.
DU is Disk Utility and should be located in Macintosh HD > Applications > Utilities. DU lets you run some maintenance checks of existing drives and format them if needed. Example, you buy a new hard drive and you have to make it Mac-happy. It's done with DU.

Iomega zip drive disk tool 4.3 wanted

Hello everyone! I bought a iomega Zip Drive to transfer data to my LCIII. I followed the instructions of the iomega manual and no luck. Overtime I start macintosh 7.5 at my LCIII no iomega zip drive icon is displayed at my desktop. The manual says that it should be "Disk Tools 4.3" I have the disk inserted but no luck. The zip drive seems to work. I also cheked the SCSI cable connecting my LCIII to my Macintosh SE and it worked, I transfer a few files from one machine to another. So the cable is fine. Thats why im thinking that the problem could be the Zip Disc Tools 4.3. Is there ant place where I can download the driver 4.3 and install it with floppys?
Thanks in advance!
Carlos

Hi Carlos,
Is it a Zip 100 SCSI drive? Did you get any software with the drive? Was the Zip disk brand new or used? Any information about previous formatting etc?
The following web page could possibly be of interest to you.
http://www.vintagemacworld.com/pluszip.html
The page describes how to make a Zip drive work with a Macintosh Plus (using a third-party formatting utility). A modified procedure may or may not be applicable in other cases. You may want to carry out a few experiments, for example, with your LC III.
Jan

Does OS 9 have built in support for external Iomega Zip drives?

Hi,
Does OS 9.x have built-in support for external SCSI Iomega Zip drives?

Yeah, you are correct, but Iomega's drivers & APPs were one really destabilizing factor for OS9, as well as ruining a few ZIP Disks with that Death Head crash, and being a nuisance. Intech's drivers gave twice the R&W speed, never failed, never crashed, could Format & Partition them... also worked for MOs, JAZZ, SyJets, other Syquests from 44MB to 550MB, and any other drive regardless of IDE, SCSI, FW, USB.

Parallel port printer connection

I have an HP 6122 parallel port printer which I've attached to my MacBook Pro running on OSX 10.4.11 through a connecting cable to the USB port (I've tried both the left and right USB port). I've downloaded driver from HP, but computer doesn't see the printer. Suggestions?

Hi urdog, and a warm welcome to the forums!
In System Profiler>Hardware>USB, is anything shown for it there?
Have you tried another PCL/hp printer in Printer Setup Utility? Have you got any hp drivers installed?
PCL 3 is quite old, but what happens if you try setting it up with an older hp driver?

Parallel Port & USB Connections

I have several older Macs & a Windows PC, all connected to an Apple 16/600PS laser printer. The arrangement has worked fine and minimized duplicating hardware. I'm thinking of upgrading the PC, but all newer models do NOT have parallel port connections -- only USB ports.
How does one deal with these changes in connectivity? Is there a way to connect parallel to USB?
Thanks.
Bill
Windows PC Windows 2000 Apple 16/600PS Laser Printer

Also, you did not indicate whether your other Macs
are simply old and using AppleTalk-over-Ethernet to
the printer, or really, really old and using
LocalTalk from the serial printer ports..
Grant,
Thanks for your suggestions. Yes, the Macs are pretty old (a Quadra and a PPC), but the LocalTalk network does just fine. My connectivity issue would be with any new PC, and Ethernet connectivity is certainly one option. Another is to buy a fairly cheap port replicator for a new laptop that gives one parallel port connectivity. One piece of new HW, no SW or driver changes to make -- that might be a more simple solution to the problem.
Again, my thanks.
Bill
Windows 2000

H55M-E33 need parallel port port connector

I misplaced/lost the parallel port thing to connect the motherboard 25 pin header to a slot with db25 parallel port connector and am trying to replace it.
Can I buy this from MSI? If not, where can I buy it and what do I ask for to get the right adapter? I have one from an older computer, but the header that goes to the motherboard isn't the right size, it's larger.

https://forum-en.msi.com/index.php?topic=144991.0
Don't post about this topic again.

Iomega ZIP drive-constantly unable to read disks when using on both PC&Mac

I'm constantly having problems with Iomega ZIP disks:
-can't be read by PC or MAC
-needs reformatting
I have to erase the disk using disk utitlities and make sure its FAT 32 (not 16) for the PC to read it.
However this is only temporary as the disk will again become unreadable by both machines.
Is this because i'm constantly using is on both machines?
Does anyone else have this problem?
Any solutions?
This appears to have started since the last major OS X upgrade - i.e 10.3 to 10.4.
Cheers
Tasha

You may not want to hear this - but the best thing to do is to get anything that matters off Zip disks, and never touch them again. They're inherently unreliable, and you're much better off using CD-R or DVD-R.

Iomega Zip driver disappeared

One day the zip drive worked and now it doesn't. I have reinstalled the driver and I still get a "no drive" message. Any clues?

Hello Cindy:
I suggest you contact Iomega tech support - perhaps there is a fix/later driver.
If you have made no changes in your system, the problem lies with the device/driver.
Barry

Satellite 5200 - Need master/slave patch for new DVD drive

I need a patch for DVD to use in a Satellite 5200.
My original DVD is broken, so i bought a Toshiba SD-C2512 DVD but it is not working inside the Satellite, but with adaptor at my Desktop PC.
I have to patch the DVD to Master.
Where can I get the file and prog to patch?

Hi
I think such patches that you mean are not available and as far as I know if you can switch a notebook from Master to Slave for example there is a jumper on the drive.
However, for me it sounds like that the drive is not compatible with this notebook. Not every drive is compatible with every notebook (e. g. pin assignment, ) ;)
You should buy another one and check the user manual. There you should find a list of compatible drives.
Bye

"IOMEGA ZIP DRIVES"

How do I prevent the LabVIEW 6.0.2 app builder from crashing with error 40508 while trying to build an application directly to my USB IOmega ZIP250?

Hello,
I believe there is a KnowledgeBase entry on the NI website that states you cannot build a LabVIEW application to any removeable media. Trying to specify your build destination as a floppy disk, ZIP disk, etc., will result in an error or a crash upon building. You must build you application to your hard drive, then copy it to your removeable media.
I hope this sheds some light on the problem for you. Good luck with your application, and have a pleasant day.
Sincerely,
Darren Nattinger
Applications Engineer
National Instruments
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

Satellite M60: Need parallel port to connect Iomega Zip drive

Similar Messages

Maybe you are looking for