Satellite M645 - How to reset the touch buttons?

Hello everyone.
I have a Satellite M645 with Windows 7 / 64 bit and recently some of the touch buttons have stopped working. These include the eco utilities, wireless, lighting, play/pause, mute and touch pad on/off button. Strangely the volume up and down work fine.
All the buttons are lighted all the time and when touched they go off (as regular) it is just that the function they're meant to do is not done.
For this I found a similar threat (http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=248139&#248139), but when trying to install *Toshiba Value Added Package* and *Flash Cards Support Utility* from the website the file I download can't be installed as I get this message:
"The version of this file is not compatible with the version of Windows is running. Check the computer's system information to see if you need an x86 or x64 version of the program and then contact your supplier."
I've tried installing both (x86 & x64) but neither of them work. That's it for now, I really appreciate any advice or side solution you can give me.

Hey,
Where have you downloade Value Added Package and Flash Cards Support Utility? I have done a Google search and it seems that Satellite M645 is an US model and therefore all drivers and tools can be downloaded here:
http://www.csd.toshiba.com
Make sure you download the correct version of VAP and Flash Cards Support Utility. That means if you have Windows 7 64bit you have to download the 64bit version too.
Another question: Have you installed all other drivers like chipset?
Also try to load the default settings in BIOS and test it again.

Similar Messages

  • How to install the touch button on the iphone screen ?

    Q:How to install the touch button on the iphone screen?

    Settings/General/Accessibility, turn on Assistive touch.

  • Satellite x200 - how to reset the Bios password

    Hello,
    I purchased a used Satellite x200 to replace my old p100.
    When I received it, I remarked the bios is locked and the person I got it from is unable to tell me the password, arguing she used the finger imprint only four long.
    Is there a way to reset the bios password and how much would it cost?
    Regards

    Hi
    The BIOS password can be removed only by an authorized service provider in country where you live.
    So get in contact with Toshiba service partner and ask for BIOS password reset.

  • How to reset the iphone without being able to use the screen or the sleep and awake button?

    how to reset the iphone without being able to use the screen or the sleep and awake button?

    Hey einsoccerstar,
    Thanks for the question. You can restore your iPhone in recovery mode utilizing the home button:
    If you can't update or restore your iPhone, iPad, or iPod touch
    http://support.apple.com/kb/ht1808
    Thanks,
    Matt M.

  • My ipad2 is disabled and my power button is not working, how to reset the passcode?

    My ipad2 is disabled and my power button is not working, how to reset the passcode?

    Hi, there is no fix for this unfortunately. However you can plug your iPad into iTunes and providing you have made a backup, you can restore from it
    you say its disabled, what does the message on the screen say?

  • Can anyone please tell me how to reset the passcode on an ipod touch?

    Can anyone please tell me how to reset the passcode on an Ipod Touch?

    Conect your iPod to yur computer and restore via iTunes. Place the iPod in recovery mode if necessary. For recovery mode see:
    iPhone and iPod touch: Unable to update or restore

  • How to reset ipod touch when frozen on apple logo

    hello
    i was upgrading to ios 6.1 on my ipod touch 4 g when it frozen
    but my my power button and home not working.
    is there anyway using me computer i can fix this
    how to reset ipod touch when frozen on apple logo
    with the problem i have
    thank you for your help.

    Hello,
    I am currently an owner of an Ipod Touch 4th generation. I see you are having problems with your Ipod Touch, so I will try to find a solution to your problem.
    Plug into your computer
    Go to ITunes
    Click on your Device
    Click on Summary tab
    Click on Restore
    Hope that helps!
    If none of the above solutions work, can you please respond back ASAP as I will try to find another solution to your problem (This might even help others with the same problem!)
    Cheers!
    Pizza98704

  • How to reset the military usage value in GTS Business partner

    Hello Experts,
    Does anyone know how to reset the Military usage value='2' to blank on the Business partner within GTS?
    I tried putting a blank there, clicking on the accept entries button followed by  saving the Business partner.
    It does not seem to work this way.
    Does anyone know if it's SAP bug for not having blank as one of the allowable values for the usage except when it's that way while newly created?
    The GTS implementation details are as follows:
    Any help with regard to this will be much appreciated......
    Thanks,
    Prashant.

    Prashant,
    As I already informed you, it is not possible to re-set the indicator to <blank>.
    From the program code, I can see that the usage indicator is only transferred from the feeder system during the creation of a customer partner.  The value in GTS is set either to '1' or '2' during creation, and cannot be changed by any subsequent data transfer from the feeder system.
    I think that logic is related to the fact that usage records may be created for multiple Legal Regulations, and those records may then be changed individually by the user in GTS.  On that basis, it would not be reasonable to over-write the values by re-transferring the customer from the feeder system.
    Regards,
    Dave

  • HT2101 I can't find the keyboard by using iMessage, but I can by using email or whatsapp? How I reset the keyboard on iMessage?

    I can't find the keyboard by using iMessage, but I can by using email or whatsapp? How I reset the keyboard on iMessage?

    Did you tap in the box at the bottom of iMessage?
    If you did and no keyboard is showing: Do a reset
    Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data
    If that didn't helped, double tap Home button, delete the Message app and reset again.

  • How to reset the router?

    I tryed to secure the router with the easy-link program and i want to reset the whole thing.Also if anyone know how to reset the netowrk setup from the control panel that would be great too.

    What router are you using?
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: some routers have a user name of "admin" ), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • I was rubbing my keys and screwed up my font setting. i don't know how to reset the font to original mozilla setting

    i was rubbing my laptop keys. i must have hit the right key sequence to change the font setting. i don't know how to reset the font. i was in mozilla at the time, so only it was affected. IE still uses the correct webpage fonts. IE has a reset on their browser, does firefox?

    Have you tried closing Firefox and visiting the site again without restoring your session? This will bypass any temporary changes.
    If the problem is the font size, you can reset the zoom level:
    View menu > Zoom > Reset
    If you have the orange Firefox button, tap the Alt key or press F10 to display the classic menu bar where you will find the View menu.
    If that doesn't help, can you describe what's different in more detail?

  • How to reset the SMC on macbook pro 15" late 2009

    Does anyone know how to reset the SMC on the macbook pro 15" late 2009?
    The instructions listed at http://support.apple.com/kb/HT1411 does not work.
    There are alot of posts in here about it, but I cant find any solutions on who to do this on the late 2009 model that have the build-in battery.

    Turn it off, connect the power supply then hold down shift/control/option while holding down the power button for 5 seconds - the power supply light will go off and on to show it's done.

  • How to reset the iphone without being able to use the screen?

    how to reset the iphone without being able to use the screen?

    What do you mean by reset?
    Reset: Hold the Sleep/Wake and Home buttons and don’t let go until the screen goes dark and the Apple logo appears (no data will be lost)
    or wipe and restore?

  • TS1425 The touching buttons and wheel on my gen 4 nano are unresponsive. any ideas?

    G'day
    The touch buttons and the wheel on my gen 4 nano are unresponsive, I have reset the device and this has not helped.
    I cannot find anything that helps, any ideas would be gratefully accepted.
    cheers

    What happens if you try a hard reset using the appropriate instructions in this Apple support document?
    http://support.apple.com/kb/ht1320
    B-rock

  • HT1212 how to reset ipod touch

    how to reset ipod touch

    As the article you linked to says:
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Wrong passcode results in red disabled screen                         
    If recovery mode does not work try DFU mode.                        
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings        
    For how to restore:
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: How to back up     
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload iTunes purchases by:
      Downloading past purchases from the App Store, iBookstore, and iTunes Store

Maybe you are looking for

  • Exporting and importing projects and DCs

    We are not blessed with the JDI, and I am in a situation whereby I would like to take a project from one machine and import it into another. I tried this by exporting to a ZIP file, but when I try to import it, I have to create a new project in the t

  • How do I turn off suggested videos using the YouTube widget?

    How do I turn off suggested videos using the YouTube widget?

  • Setting CLASSPATH question

    Hi,           I'm evaluating Weblogic 5.1. My evaluation requires me to write an           Enterprise Java Bean that uses Container Managed Persistence, place it on a           server, and have an HTML page call into the EJB through a servlet. The   

  • SAPscript address name1 and name2 - print on the same line

    I want to print name1 and name2 on the same line in an address on a check. Does anyone know how to do that ? I am usign the ADDRESS SAPscript command.

  • TIFF compression - how to disable?

    Hello - I'm using InDesign CS3 at a newspaper. I paginate the paper and print to a PDF file that goes into hot folder, gets ripped through Xitron Harlequin RIP then goes to a Computer to Plate. I'm working on Windows XP. That's just some workflow bac