Satellite notebook powers off when battery is connected

Hi folks
So my battery wasn't charging so i put the laptop into stand by so I could pull the battery out.
Just as I went to pull the battery out it woke up and as i pulled the battery out the laptop suddenly turned off and would turn back on.
The laptop runs fine of the mains without the battery plugged in but as soon as I plug the battery in it kills all power to the mains.
Question: have I shorted out the battery or have i shorted something out in the laptop?
Stephen

Hi
> The laptop runs fine of the mains without the battery plugged in but as soon as I plug the battery in it kills all power to the mains.
Please note; the battery should be inserted only if the AC adaptor is disconnected and if the notebook has been shut down.
Dont connect the battery while notebook is running!!!

Similar Messages

Satellite P205-S6277: Can I take off the battery and connect the power too?

I am working on my notebook Toshiba satellite P205-S6277, 80% of my time at home.
Can I take off the battery and connect the power to a backup UPS in order to make battery life longer?
I can charge it once a week.

Of course you can do this. You can remove the battery and work on AC power supply only. Be sure there is no dust on the desk and the battery place on the notebook stay clean for further usage.
Bye

Ios7 installed on iphone 5 and then the device swtich off when battery is 10% only and never open till power source connected

ios7 installed on iphone 5 and then the device swtich off when battery is 10% and never start till power source connected ..

I have the same issue with the following setup:
Garmin 2597LMT
iPhone 5
Motorola T605 bluetooth hardsfree system
I ended up disabling the nuvi bluetooth -- I don't subscribe to any smartlink services -- so I'll guess i'll go without Weather on the nuvi for now.

Iphone 5 switches off when battery still has 15%

After updated to iOS 7, my iphone 5 always switched off when battery still have 15%. Anybody have the same issues?

Sounds as if the battery may need to be recalibrated. Let the battery drain until it turns off. Then connect the phone to the charger and let it charge to 100%. Disconnect and then use it. It should get it back to a better read. The batteries are designed to shut down when the battery has a certain amount of power left. The battery percentage is not always that accurate.
You can take a look at this link from Apple about batteries. http://www.apple.com/batteries/iphone.html

Why iphone get on and off when battery is good

why iphone get on and off when battery is good

iPhone User Guide
The Basic Troubleshooting Steps are:
Restart... Reset... Restore from Backup... Restore as New...
Restart / Reset
http://support.apple.com/kb/ht1430
Backing up, Updating and Restoring
http://support.apple.com/kb/HT1414
If you try all these Steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step... Be sure to make an appointment first...

Iphone 4 auto shut off when battery 20% and lower.

My Iphone 4 auto shut off when battery 20% and lower. The phone is only 1.5 years old. Can I know why this happen?

Most commom reason for this is faulty battery. You could try Restore with iTunes on computer, at end when prompted, Set Up iPhone as New. If still problem and you have AppleCare, take to Apple for resolution. If no coverage, make Genius reservation and take to Apple Store for quick free battery diagnostic testing.

Why does computer turn off when battery 40%?

Why does computer turn off when battery around 40%? I have tried replacing the battery.

Replacing as in "removed, re-installed", or "bought a new one"?
This is my display from "Apple menu > About This Mac > More Info > Power"
"Normal" means no issues.
I will stop now in case you have actually put in a *new* battery ...

Macbook Pro powers off when on battery power

Help! My MBP 17" now powers off after a couple of minutes on battery power. When this happens, trying to boot again, the system will power off again while loading the OS. The only way to get the MBP to boot then is to plug in the AC adaptor.
I've reset the SMC and reconditioned the battery. Both the OS and the battery think the battery is fully charged. This didn't happen before upgrading to Leopard.

I believe the color of the magsafe was green and that it wasn't charging. (The MBP thought the battery was at 96%.)
Here's the profile after I got to work and plugged in my magsafe (which is a second magsafe I keep at work), the color is amber:
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: Yes
Battery Information:
Model Information:
Manufacturer: SMP
Device name: ASMB014
Pack Lot Code: 0001
PCB Lot Code: 0000
Firmware Version: 0102
Hardware Revision: 0202
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 5048
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 5472
Health Information:
Cycle count: 97
Battery health: Good
Battery Installed: Yes
Amperage (mA): 469
Voltage (mV): 12390
After charging, the magsafe is green and this is what profiler says:
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: No
Battery Information:
Model Information:
Manufacturer: SMP
Device name: ASMB014
Pack Lot Code: 0001
PCB Lot Code: 0000
Firmware Version: 0102
Hardware Revision: 0202
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 5472
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 5472
Health Information:
Cycle count: 97
Battery health: Good
Battery Installed: Yes
Amperage (mA): 200
Voltage (mV): 12368

MicroPhoto flashes and powers off when connected to compu

I bought a microphoto about six months back and had no problems with it until the last week or so. First it became more difficult to get the power on- I'd have to hold the switch in the power on position for a few seconds. But now- every time I plug the player into the computer- the screen shows a quick white flash and the player powers off. I am not able to get the power back on unless I move the battery around. And then- when the power comes back on- I invariably get a "low battery" message, even if the battery was fully charged before I plugged the player into the computer. Anyone have any idea what's going on?

See Here for Device Not Recognised...
http://support.apple.com/kb/TS1538

My display goes off when Battery being charged on Acer E5-511 after upgrading to Windows 10

I upgraded my window 8.1 to Window 10 on Acer E5-511 machine yesterday. I notice that when I switch on power to charge its battery, a beep sounds and display goes off. when power is again switched off the display comes back with a beep again. However, when the machine battery is allowed to charge for some time, either it goes to hibernation mode or stops working since display does not come back even after switching off the power supply. This peculiar problem did not existed when I had used this Notebook with windows 8.1 for past eight months. Can any one help me to solve this problem as i am being forced to charge the battery only when Notebook is not powered on.

A BIOS update fixed Grey Bat's (a.k.a. Myotis grisescens) problem. http://community.acer.com/t5/Windows-10/Restart-problems-with-Acer-E5-511-P8C8-laptop/m-p/370322#M24 http://us.acer.com/ac/en/US/content/drivers Edit: Acer also said that "Your system may require additional software, firmware, and/or a BIOS update to install and run Windows 10." http://us.acer.com/ac/en/US/content/windows10-eligible-models

PC Powers off when downloading through iTunes

This is totally weird, and 100% replicatable.
I initially discovered this when I got support to help me recover some lost music. It showed up in my downloads section. It started to download, then instantly my PC is powered off.
No blue screen, no error of any kind. One second, happy iTunes progress bars, the next second, powered off. This is a Laptop in a dock using AC power, so it's bypassing battery power too. It just clicks and is powered off.
I reinstalled iTunes and was able to download everything. I assumed the issue was resolved until I bought something new and it happened again during the initial download of that new album. Now it's happening everytime I try to download, new or recovered purchases. I've yet to be able to download the last album I paid for.
Help?

I initially discovered this when I got support to help me recover some lost music. It showed up in my downloads section. It started to download, then instantly my PC is powered off.
Since you're getting that when doing Store stuff, if you've got a Radeon-based display adaptor or video card, I'd try updating your video drivers as per:
[iTunes for Windows: System restarts, blue screen, or quits unexpectedly when accessing iTunes Store|http://support.apple.com/kb/TS3441]

Samsung Gusto 2 powers off when close the lid

Saw another thread ("powers off randomly") about this and no answers were ever posted.
Is there a solution? Phone has plenty of charge in the battery and works fine when it's powered on. It just powers off immediately when I close it.

Removed battery and reseated. The phone now seems to remain in the powered on state when I close the lid.

Z10 shutts off when battery discharge reache 44 %

i came across many thread z10 random shutts of on bb on crackberry threads but no solution yet my z10 shutts off randomly ........ Mostly it happens when battery discharge reaches 80 % and it always shuts off when z10 battery discharge reaches 44 % ............. Where are bb developers ...... Not a single word from them ....... is this solvable or not ......... ?? r i should change my mobile ?

Hello,
You should try this...with your BB powered ON and on the OEM charger, remove the battery. Wait 5 minutes, still with the BB on the charger. Insert the battery and allow it to boot up. Leave it on the charger for at least 4 hours.
See if that helps correct your situation.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

New 8110 powers off when placed in holster

I just replaced my 8100 with a 8110 and realized it was powering off on its own when I place it in my holster I used with the 8100. Any ideas? I've looked all through the phone for power options and have found none...

Strange indeed, the same holster works fine for both devices (in most cases).
Try facing the device in the holster in the other direction, facing inward towards the clip.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

PC powering off when Video in Browser if Adobe Flash used...

Hello.
My PC may randomly power off when using adobe flash video in browser.
Similar topic:
http://forums.adobe.com/thread/1258555
a) Temperatures in system are OK.
b) System survived multiple stress tests. Some were focused on PSU, some on CPU, other on memory and other on graphics.
c)Tested on:
Opera 12 and 20
Browsers were either playing Flash, with chance to power off. When uninstalled Opera requested Adobe Plugin automatically on Youtube.
Internet Explorer 11
If Adobe ActiveX not present, videos on youtube were played via HTML 5 without trouble. When ActiveX installed there was still no trouble, but since I have AMD graphic card, IE requested to enable "AMD steady video plugin". Once enabled there is still some chance to power off the PC.
Catalyst settings:
When AMD steady video is not installed, or is disabled the chance for this behavior is still here.
If installed and enabled, system did not crashed due this.
I tried latest Adobe Flash 12, and previous 11 are causing this. I tried older Catalyst (13.12), and behavior repeats.
Event log:
Empty. it literally looks like when somebody pulls the plug out.
GPU behavior:
Usually last observed thing is that GPU clocks to full frequency for a while, and then to "video frequency" of 501Mhz.
Other behavior:
This behavior is more like to happen when PC is "freshly booted". The longer is running, the longer it took to power off.
The symptoms are confusing to me. The issue is surely at least partially HW related, but bound only to Adobe Flash. No other HW accelerated video codec is causing similar behavior (at least until now).
On the other hand, its clearly bound to Adobe Flash 12 or latest 11, and some Catalyst settings.
Can you recommend me Adobe Flash version which is not using Amd Steady video at all?
Thanks.

Thanks for reply.
a) System passed all stress test, whether graphical PSU, memory or CPU based.
b) Its powering off only when using Adobe Flash player in browser.
I confimed that only Adobe Flash in any browser i tested is causing failure, but I re-think again what components are included in the whole chain. This was happenning even on stock frequencies and voltages, but...
(Data stream arrives from NIC, is transferred to RAM, then CPU picks it up, send it to GPU for (HW accelerated) decompresson , then back to CPU where browser start to manage the data and then back to GPU for displaying)
a) CPU Core failure would cause BSOD, because I have 5 other CPUs to handle the event this way.
b) GPU, NIC or Sound card failure will also lead to BSOD - CPUs will remain active...
c) Memory failure will also lead to BSOD...
There is but single part of my PC, which can cause "Instant Power-Off" symptom. Its Northbridge/L3 cache.
Even when the Stock settings were causing exactly same symptom I focused on manual Bios settings. Yesterday evening (rather today early morning) I found configuration when Flash was stable.
Its not overheating, rather than overload of Northbridge/L3 cache. The amount of transactions between all devices must be tremendous... Therefore I had to customize CPU/NB settings in order to keep Adobe Flash stable. (slightly increase of CPU voltages +0,02v on CPU, 0,05v on NB when compared to stock).
For now I have to re-test those settings for few hours with Flash, and later with stability tests.

Satellite notebook powers off when battery is connected

Similar Messages

Maybe you are looking for