Satellite P10-873 Wireless LAN Connection

Hi all,
I have a Satellite P10-873 laptop. I've just purchased a Netgear DG834GT wireless modem/router and cannot get fully connected to the internet via Tiscali (ISP).
The problem manifests itself in that I can connect to the router and can even ping various sites on the net. However trying to connect to a site using MSIE I just get "cannot connect" rejection page.
In addition using the CMD prompt, attempting a Telnet session to a web site on port 80 is rejected e.g "www.bt.com 80".
I've set all security to a minimum with no effect.
I have an other notebook which connects and functions perfectly with the Netgear/Ticali setup. I've also identically configured MSIE on both machines without success.
Does anybody have any ideas what could be causing this???
Thanks Mike
[Edited by: admin on 14-Oct-05 11:49]

I have just set up the same router/modem (yesterday). I had a similar problem until I disabled Norton's Personal Firewall. (Windows Firewall already disabled) It then connected and I set up Nortons again afterwards (despite the manual saying do not use 3rd party firewalls. I also need help with my P10-304. I can't get the Intel 2200BG wireless minicard to work. Any ideas?

Similar Messages

Satellite P10-792: wireless LAN Intel 2100

Hi!
I tried to install INTEL BG 2100 wireless mini-PCI card. Drivers work OK, but they say "Radio off". Nothing changes when I press [FN]+[F7]. Card is OK (tested in some Arima-made notebook).
How can I use the card?

I have a similar problen with my A30 Satallite. Driver installs OK and device works fine but keeps telling me to enable hardware switch. When you say enable switch do you mean somewhere in the system config because I have found that switching to on position does nothing, as iff switch is not connected.

Wireless LAN Connection Configuration

Need Basic Wireless LAN Connection Configuration Example

Hi
This link provide WLC configuration examples
http://www.cisco.com/c/en/us/support/wireless/5500-series-wireless-controllers/products-configuration-examples-list.html
Refer config guides if you need step by step guide for all features configurations
HTH
Rasika
*** Pls rate all useful responses ***

Can some please help me with the Wireless LAN Connection Configuration?

I want to configure WLC in my Testing Lab , need help with the step by step configuration of WLC.

Please go through the below link for the Basic Wireless LAN Connection Configuration Example.
The below link has end – end configuration steps with the images.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68005-wlan-connect.html
Have i answered for your query.

Satellite P10-804 wireless card upgrade

Hi,
Ive been trying to find a list of compatible wireless cards to upgrade my Satellite P10-804 but can't find any.
The the current wireless card is a Toshiba PA3171U-1MPC but it doesnt do the 802.11G standard and no WPA security.
Anyone know of what are good replacement cards that will work on my laptop?
Ive come across this one but Im not sure if it is compatible or not as I can't find any compatibility info for it: PA3416U-1MPC
Thanks,
Mark

Hi
I think the PA3416U-1MPC should be compatible.
I mean the notebook supports the miniPCI Wlan card and the PA3416U-1MPC is a miniPCI Wlan card.
The WLan antenna behind the notebooks screen should be connected to the connectors placed on miniPCI WLan card.
The two connectors are marked with MAIN and AUX. Normally a white cable goes to the MAIN and a black to the AUX
bye

Satellite P10-835, Instructions to connect to wifi using Atheros client utility?

i have a P10-835 and need to configure the Atheros client utlitiy to connect to a Netgear 834G wireless router. Are there any instructions on how to configure the Atheros client?

Hello
1. START button > All Programs > Atheros > ACU > Atheros Client Utility
2. 2. Select "Profile Management" tab an click on "New"
3. Put the right Profile name and Network name
4. Check Security tab and put the password if your network is encrypted
5. Check also if the windows wireless configuration disabled it
(IT MUST BE DISABLED if you use some client for wireless connection)
You can find this option in Wireless Network Connection properties under Wireless networks.
Bye

Iphone 4 Wireless LAN connection

I have an Iphone 4 and the Actiontec Router.
Recently if I leave my home and then return, my Iphone will connect to the wireless but I am unable to get email or do anything that uses the Internet via the wireless. I have installed a Ping application on my iphone and when I ping the default gateway (192.168.1.1) it times out. When I turn off wireless and then re-enable it works fine.
Additionally if I don't use my phone for sometime it will do the same thing, I cannot get my email unless I disable and re-enable wireless. Anyone experience this problem or know of a work around?
I am using WPA2 AES, 802.11G only and automatic channel selection. I don't have any problems with laptops connected via wireless. I have also tried used Static IP addressing but that didn't do anything either.
Thanks, Jim

yes. It get 192.168.1.5 for example and then DG and DNS of 192.168.1.1
My ping program shows me the IP address of 3G and wireless LAN.
Even if I ping 4.2.2.1 it will time out. If I disable wireless and ping 4.2.2.1 it works. Everything begins to work. Then if I re-enable wireless I can then ping my DG and 4.2.2.1 and get email, etc.
Just seems to happen mostly when I leave for a while then return home.

Satellite U-305 wireless internet connects at 54Mbps, then freezes

Using the internal wifi, an Express Card adapter, or a USB wifi adapter I can connect to the internet, but when the initial page download bar reaches halfway it grinds to a halt.
The gauge shows a five bar connection with 54Mbps throughout.
When I connect with a cable, I get 100Mbps and complete, fast internet access.
This occurs with Firefox, Internet Explorer, or AOL.
This has been happening all the time I've had this computer.
The wifi on my other wireless device, a Palm T|X, works flawlessly.
Thanks for any help.

What Antivirus and Firewall software do you have installed? Maybe they are causing Internet problem.
Have you tried updating the Wireless LAN Device Driver? (check the Toshiba website)
Also update the BIOS.

Wireless Lan connection issue with Linux clients

Hi
In a large Wireless Lan enviroment for a university, we have 3 WISM moduls attached on a 6k hw - Manged by ACS v6.0.181.0
We recently upgraded the software version of the controllers from 4.x to 7.0.98.0 - the Emergency Image version is 5.2.157.0
Since then, the students with Linux clients have massive connection issue - repeated connection lost in a short time period.
However the students with Windows clients have no problem at all.
The studends report, that their linux clients getting so much of some kind of unnecessary broadcast traffic which can not be handled by the NIC - and the NIC goes down - and this happens all 5-10 minutes.
Affected Linux clients are: Ubuntu v10.10 - also OpenSuse, Fedora and Arch-linx with latest OS version.
Any Idea how I could solve this problem?
Thanks in advance for your help

Hi Nicolas
Thanks for your reply. The broadcast forwarding is disabled on WLC's.
Pls find below the attached picture, which shows the captured broadcast traffic on a linux client (sent by a student to me).
I'm not sure, if its really only the broadcast traffic, which the linux clients can not handle.
From my point of view, it seems also to be that the linux clients are somehow disadvantaged among the other clients like windows or mac, if they all trying to get a wireless connection.
But the fact is only the linux clients are affected - and this happens to the linux clients only in our wireless infrastructure.
Windows or Mac clients have no such problem at all
regards
Enis

BT HUB5 Drops wireless & LAN connections 01/01/201...

Hello
Wireless and LAN connections has been working perfectly fine when i first signed up to the complete BT package (broadband,phone,TV) in September 2014. During the beginning of January 2015 to now February 11/02/2015 my wireless connection drops out in the morning and evening multiple times 5am-7am at least 3 times in the morning and at least 5 times at night 6-12. This drop out also affects LAN connections even though the BT HUB 5 is still lit blue, there is no fault light, once or twice I seen the fault light.
I cannot not browse the internet and use Netflix’s etc because the wireless connection drops out regularly. I have spoken to BT’s Global Service Desk who reported there is a problem, however a UK call centre engineer confirms there is no problem and the issue lies with ‘Interference’ and their excuse was it was probably conflicting with other wireless devices which is total nonsense.
I have checked with my neighbours and they have not bought any new devices or changed anything which would conflict with wireless connections, including kitchen appliances. I also have followed BT advise and switch everything off and on again, reset the router back to default, they have reset their end, changed the wireless channel etc. still get the same issues.
Everything has been working fine up until January so something has changed on BT’s end to cause regular problems which affects LAN and Wireless connections. Many sources on the internet suggest firmware and line testing for faults like on their BT HUB5. BT suggest there are no problems and everything is working fine and they have no problems on their end. I’m still waiting for a solution from BT……?; an issue like this would have been resolved or never happened with SKY and Virgin fibre connections.
Please can someone help and adviise best practice to get my BT HUB5 working again properly or suggest what BT must do to pull there fingers out and take ownership of this issue. Many thanks.

Sorry to hijack someone else's thread but I seem to be experiencing exactly the same issue.
Service was installed around about Sept last year and has been fine until the last few weeks when the same wireless drops started to occur. I have no new equipment connected, but all devices experience the problem.
Having looked at my HH5 version, I'm on the same:
BT Home Hub 5 (Type A) | Software version 4.7.5.1.83.8.204 | Last updated 21/01/15
I noticed the update date of 21/1/15 which probably coincides with when the problem started, so I wondered if there might be a known issue with this software version?
Thanks

Satellite P10-873: power supply and CPU overload

I have the P10-873 notebook for 4 months.
The problem is that it turns off when it is connected to AC power.
I can only work using the battery. When the battery goes off I charge it normally (with the notebook turned off) and then I use the notebook only with battery again.
If I connect it to the AC power it turns off after 3 minutes maximum!!!
I have checked the CPU usage while connected to AC and it seems that the CPU is overloaded (from 65-98% - where it shuts down!) without running any applications other that the processes needed for the notebook to operate.
I have sent the notebook to TOSHIBA and they returned it saying that they updated the BIOS.
Unfortunately the problem was not fixed!!!
Do you have any suggestions?

Hello
Sorry but I think that there is some problem with notebook power supply electronic. The BIOS update can not solve the problem at all. Please contact your notebook seller or try to contact the Authorized service partner again. They should check the unit again.

Satellite Pro M30: Wireless LAN/ZeroCfgSvc MFC Application

Whenever i turn on the wireless lan switch an error msg appears " ZeroCfgSvc MFC Application has encountered a problem and needs to close.
What shall I do?

Hi
I have read on some websites that a new wireless driver update could solve this issue.
Try to download the new wireless update from the Toshiba website:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
or from the Intel website:
http://downloadfinder.intel.com/scripts-df-external/Support_Intel.aspx
Check also this site:
http://forums.divx.com/groupee/forums/a/tpc/f/221101651/m/693108652
http://www.neuber.com/taskmanager/process/zcfgsvc.exe.html
Regards

Satellite P10-873 randomly freezing

Hi all,
I've have a P10 and on average a few times a day the machine seems to freeze in Windows XP for 5 - 10 secs. During this time you cannot move the mouse or use the keyboard. Often during this time the fan kicks in to its highest setting, however the strange thing is it doesn't always do it when the fan goes to its highest setting.
The machine has done it from day 1 and have now had it 8 months.
It isnt a spyware or virus problem, i use all the latest drivers and have tried reinstalling the pre-installed software with no success.
Does any one else have this problem or know how to fix it.
I've lost a bit of confidence in Toshibas, my first one was faulty and had to go back and am now beginning to regret not trying to get this fixed at soon as i got the new replacement, at the time didnt really want to go through the whole process of sending another laptop back, so decided to live with it.
Thanks
Message was edited by: corh5

Hi there,
The fact that the fans sometimes kick-in during these temporary freezes would suggest that some intense CPU activity is taking place during this time. The fan activity is almost always related to CPU activity in some way. Do you have any processes or tasks scheduled for routine execution ? I believe that Windows Update will check for updates routinely as will many of the available ad=ware and spyware products. You may also have anti-virus software running which is trying to check the internet for available updates.
You do not say if you laptop is permanently connected to the internet, but it is possible that some process is trying to locate a suitable COM port and is causing the rest of your laptop to hang until it times out.
It may well be a case of trial and error to locate the offending process since there will be many background processes present in XP
HTH

Satellite Pro M30 - wireless cant connect to Internet

Hi
I'm having problem when trying to connect to internet by using wireless PC card. I did all card instructions, it's indicates green light in power field but no lights in link field?
Why?! Pleas help.
Thanks

Hello
First of all the wireless card must be installed properly. I dont know which card you have exactly but check please in device manager if the card is listed and ready to be used (check device status).

SD slot no longer works on my Satellite P10-873

Hi there.
Attempted to update the driver for the integrated SD slot in order to read my 2GB card and now it won't even read a 128MB card correctly. The directory structure appears ok but Explorer just hangs with I/O errors.
Have tried uninstalling the SDA controller driver and installing again but not look (although it says it is working correctly).
Tried installing the SD Memory Card driver v2.04 from the download section but under IDE channels, device manager states that it failed to start (code 10) although I don't remember it being installed before anyway. Isn't just the controller driver sufficient?
Hope someone can give me some clues!
TIA

The SD memory controller driver should be installed at first.
After installing the SD-mem controller driver, you can install the SD memory card driver.
In my opinion the error code 10 appears because you have tried to install the memory card driver but the host control driver was not installed!
On the Toshiba page I have found only a SD Host Controller for W2k and not for WinXP.
How did you use the SD card with WinXP before updating the host controller?
Did you format the SD card with another device??
Did you try to format the 128MB card with the SD card format utility??
Check it!
If it does not help you could try to remove the SD card control from the device manager.
Then reboot the unit and try to install the original host control driver again.
Check another notebook drivers for compatible SD host control driver for WinXP

Satellite P10-873 Wireless LAN Connection

Similar Messages

Maybe you are looking for