Satellite P100-429 - New WLAN card doesn't work

Hi,
I've just upgraded my home network to draft 'N' standard and thought I'd upgrade my WiFi card on my P100-429 Laptop;
Laptop is running Vista Home Premium, and has the latest BIOS and Drivers installed.
Laptop currently has an Intel 3945ABG card fitted, which works fine. I purchased an Intel 4965AGN Card but when I fit it, the computer powers up, but wont load (lights on, fan on - nothing else)
O.K. - So I read up on a few forums, could be a bad card, so I bought a Toshiba branded 4965AGN card - P/N G86C0002P710
Still have the same problem - the computer refuses to start up. Intel tech support say the card should work?
Obviously a compatability issue - is there anything I can do about it?
Or does anybody know what type of card I should use?
Thanks for your help!

Im not a Satellite P100 owner but is your notebook equipped with 3 or only 2 antennas?
If your notebook does only have 2 antennas you cant upgrade it to draft N because this WiFi standard needs 3 antennas.
I think your notebook does only have 2 antennas so this would be the reason why both cards are not compatible to your notebook.
Greets

Similar Messages

Satellite A300D-11v - WLan card doesn't work under Win XP

Ive problem. Im looking everywhere and i dont know whats happened.
I have installed XP and Ive problem with WLAN. Before Ive used Vista and was ok :)
I took driver for RTL8187b from
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=1&PFid=1&Level=6& Conn=5&DownTypeID=3&GetDown=false&Downloads=true#R TL8187B
and tried from official Toshiba website.
In device manager everything is ok, but I cant connect.
This doesnt work:
"The WLan card is from Atheros and not from Realtek! The LAN card is Realtek but not WLan card!
The Atheros driver can be found here:
http://aps2.toshiba-tro.de/wlan/
Can somebody write me step after step how this fix.
Please help me and sorry for my English :)

>Also can try reinstalling the drivers than appear in this web site, here appear the Atheros Drivers than your notebook need.
Your notebook doesnt support Atheros card but Realtek WLan card.
>In device manager everything is ok, but I cant connect.
As you said the WLan card was recognized properly but you cannot connect.
Why?
Im not sure why but you should firstly check if your WLan router uses the same WLan standard (802.11 A B or G) like the WLan card.
Check the settings!
Then check if the right WLan encryption has been chosen, check if the Mac address was not enabled, check if firewall doesnt affect the WLan connectivity.

Satellite 2410-413: USB2 PCMCIA card doesn't work

Good morning. It is my first time on a forum, and my English is poor.
I have tried to install a PCMCIA card with 4 USB-2 ports (hw & sw) on my Satellite 2410-413 in order to use a DTV dongle (hw & sw).
It will not work: The ports seem to be declared all right in the computer but in effect, a simple 64 MB USB-2 memory key [a Sony "micro-vault" key), will not work, and neither will the Winfast DTV dongle.
Paradoxically, both the mem key will work on any of the three USB-1 ports, and the DV dongle will light up on any USB-1 port. The PCMCIA card with 4 USB-2 ports is new. I cannot locate the origin of the problem.
Would any one help me with this question?
Thank you in aadvance for your reply. Here is (maybe ?)
Another way of formulating the question: how are USB ports managed by the system?

> Hello Rasta
>
> Sorry but I think that this question should be the
> right one for PCMCIA producer. Try to visit their
> support page. Maybe you will find some answers.
> Believe me on this way it is not easy to say why this
> happen. Toshiba is maybe responsible for PCMCIA card
> functionality but not for used card.
>
> Good luck!
Many thanks to you Mike30.
I have a couple of ideas now:
- supplying the USB2 card with additional power (ie other power than computer), (but how?)
- uninstalling and further, re-installing the USB2 "Truewin" PCMCIA card bus, and after that trying the "leadtek-brand" DTV sw.
Cheers,
Philippe

Satellite 5200-903: Mini PCI Card doesn`t work

Hello,
I am a user of an:
Satellite 5200-903: P4-M 2.2/256+256 DDR/60GB/15T SXGA+/DVD-R-RW/nV FX 5600/cPad/WIFI ready/XP
My computer is equipped with an Toshiba Wirless lan Mini PCI Card.
I installed the card a few years ago - everything worked wonderfull.
At the beginning of 2006 I installed a new operating system (XP Pro + SP1, same system as before) because it was necessary.
I installed all driver for the W-Lan Card, obviously the card worked in the correct way (no driver incompatibility or other problems).
But, and thats the reason of this topic here. It isn`t possible to connect my card to any Hot Spot. I tried it with 2 different access points, but the result is the same. "No connection Point found".
Has anyone any idea what to do or in which direction I could look for the failure? Is there maybe any special Software necessary (I couldn`t remember, that in my last installation I had needed special driver or software)
If further informations are necessary, please inform myself.
(sorry for the terrible english, but it isnt my first language.)
THX for your help

Hi,
thx for the hints. But unfortunately none of these solved my problem.
1. I checked my device Manager, it`s shown a Toshiba Wireless LAN Mini Pci Card
2. The device is activated, with no problems
3. My wireless activation switch on the left notebook side is activated (led lights yellow)
4. Pushing the Fn+F8 Button results nothing
(wenn i press the combination during the Notebook switch is off - i got the message "wireless connection is deactivated, please activate")
What have to happen, when pushing the Fn+F8 Button during the wireless switch is activated? Is there any message on the screen?
Concerning the installed driver, how could I check what type of card is installed in my notebook. I know, that there a two types of driver and card existing, toshiba and atheros.
But, if the installed driver causes no problems I guess the right driver is installed.
Thx for any further Idea...
C.

Satellite P100-429 - No sound after Windows 7 installation

I have a Satellite P100-429 Purchased Nov 2006.
I have just upgraded from XP to Windows 7 and Office Pro Plus. All works well but there is no sound if I try to play a CD. I have done usual checks for Mute etc. but no Joy. In device manager a yellow triangle with exclamation mark within is against my sound device. C
an I download a new driver to solve problem or is it more complicated than that? Than you

Hello
For me it sounds like that you didnt install the sound driver for sound card
According the Toshiba website there is no 64bit sound driver available for Satellite P100 but I noticed that Satellite P300 supports Windows 7 64bit and has Conexant sound card too. Maybe this driver is working for you too.
Just search for Satellite P300 drivers and test the sound driver It should work! :)

Need WXP drivers for Satellite P100 -429

Hi,
I had to reinstall windows XP on my gf Satellite P100-429, but she lost the origina disk, so when i installed the new XP there are the following devices missing drivers (they have yellow question mark beside them) and I cant connect the laptop to the internet.
1. Audio Device On High Definition Audio Bus
2. Ethernet Controller
3. Mass Storage controller
4. Netwrok controller
5. SM Bus Controller
6 Video Controller (VGA Compatible)
Can anyone tell me where I can find these drivers, i have been looking all day for them.
I imagine if I can find them its just a case of putting them on a disk or usb key and installing them ?
Thanks a million.

You must see this problem from other side. Fact is that all drivers, tools and utilities must be installed in right installation order. How to do this is listed in Installation Instruction document and this can be downloaded on this download page for your notebook model.
Obviously you didnt follow this order and some drivers are missing now.
1. Audio Device On High Definition Audio Bus try with sound driver and install also modem driver
2. Ethernet Controller install LAN driver
3. Mass Storage controller is chipset utility installed?
4. Netwrok controller is WLAN driver installed?
5. SM Bus Controller try with flash media driver
6 Video Controller (VGA Compatible) display driver
Install this and post result but, as I wrote before best way to install all stuff properly is to follow install instructions document.

WLAN adapter doesn't work on my Satellite A200

Hi,
My WLAN adapter doesn't work under Vista. If I press FN + F8 nothing happens. The wireless-communication is still offline.
What can I do?
Details:
Typ: Atheros AR5008X Version: 7.2.0.164
Notebook Satellite 200
PSAE6E
Please help me!
Thx in advance!
Phil

BIOS bug? I dont think so
Firstly you should ensure that this is not a hardware issue. In such case insert the Toshiba Recovery CD and reinstall the OS on this unit. This will set the notebook to the factory settings. Note; this would format the whole HDD.
After new installation, you have to enable the WLan switch at the notebooks side and then you could use the button switch FN+F8 to select the WLan.
I presume you have already configured your Wlan router. So the same settings like SSID, WLan encryption, etc must be set on the notebook too.

Ethernet card doesn't work with new arch install?

Hi guys,
so this is kinda my first post, not that I'm new to arch i just never had an issue i couldn't figure out on my own... But i love arch i have been using it for about a year now and have had no serious problems except for this. I have had arch running on an older dell vostro 200 desktop before i reinstalled with a vary similar issue except that the fix i came up with doesn't work anymore. I will tell you about the first issue first because i ALMOST posted on here about it originally but i figured out a way to make it work even though it was a hassle.
After cold/rebooting my computer the network card doesn't work at all. lspci reported that the kernel module e1000e was the correct one (i have verified this) and that the kernel has loaded it, i verified that with dmesg but still it wouldn't work. After much much anguish and hairpulling, I realized that it had to have something to do with the module so i tried forcing it to reload with rmmod e1000e and modprobe e1000e and it still wouldn't work until i physically unpluged the ethernet cord and pluged it back in until the light on the NIC turned on. After that everything works as normal i could even unplug and plug it back in with no problems. So eventually i wrote a script that did this for me (except for the uplugging and plugging part) and i used that when i cold/rebooted.
But now i have the exact same issue after reinstalling arch to the T except for the fact that the (crazy) fix i came up with doesn't work now. I used my "fix" after booting from the arch cd and it worked just like it always has. And now after rebooting into my fresh system the fix doesn't work anymore. So now i'm back where i was to begin with but i have no idea what to try next. I didn't do anything particularly different during installation except i added a udev rule for the e1000e module just to see if somehow that would fix the problem... it didnt and i have since deleted that (to see if it was the problem). The only other thing that is different is the root and home are now btrfs partitions instead of ext4.
I have booted several other live cds and dvds (diferent distros) including arch derivatives such as manjaro and they all worked just fine, using the same kernel module (e1000e). I'm not sure what that could mean but i know that it means there is a fix for this some way or another. I am going to hook up a wifi adapter and connect that computer to the internet to put some more information up if it's needed (asked for) but for now lspci -vnn | grep -i -A 10 net reports
00:19.0 Ethernet controller [0200]: Intel Corporation 82562V-2 10/100 Network Connection [8086:10c0] (rev 02)
Subsystem: Dell Device 0238
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at fdfc0000 (32-bit non-prefetchable) [size=128k]
Memory at fdfff000 (32-bit non-prefetchable) [size=4k]
I/0 ports at ff00 [size=32]
Capabilities: [c8] Power Management version 2
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [e0] Vendor Specific Information: Len=06 <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
ip a reports:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
3: enp0s25: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:1d:09:8c:36:f6 brd ff:ff:ff:ff:ff:ff
4: wlp0s29f7u3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 64:66:b3:16:92:10 brd ff:ff:ff:ff:ff:ff
inet 172.16.1.55/16 brd 172.16.255.255 scope global wlp0s29f7u3
valid_lft forever preferred_lft forever
inet6 fe80::6666:b3ff:fe16:9210/64 scope link
valid_lft forever preferred_lft forever
lsmod | grep e1000e
e1000e 215644 0
ptp 17692 1 e1000e
any help on what to do next would be greatly appreciated.
Last edited by mvheart/dev/null (2014-08-18 04:02:12)

Sorry I was thinking that it was say "state up" after that, I was looking in the wrong place... It's been a long time since I was playing around with this. So it is as i thought it was before?
[aaron@arch-box Arch-Linux]$ sudo systemctl start [email protected]
[sudo] password for aaron:
Job for [email protected] failed. See 'systemctl status [email protected]' and 'journalctl -xn' for details.
[aaron@arch-box Arch-Linux]$ systemctl status -l [email protected]
● [email protected] - dhcpcd on enp0s25
Loaded: loaded (/usr/lib/systemd/system/[email protected]; disabled)
Active: failed (Result: exit-code) since Mon 2014-08-18 11:20:29 EDT; 4min 11s ago
Process: 17650 ExecStart=/usr/bin/dhcpcd -q -w %I (code=exited, status=1/FAILURE)
Aug 18 11:19:59 arch-box dhcpcd[17650]: version 6.4.3 starting
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: adding address fe80::ae3:ee04:7099:77c5
Aug 18 11:19:59 arch-box systemd[1]: Starting dhcpcd on enp0s25...
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: waiting for carrier
Aug 18 11:20:29 arch-box systemd[1]: [email protected]: control process exited, code=exited status=1
Aug 18 11:20:29 arch-box systemd[1]: Failed to start dhcpcd on enp0s25.
Aug 18 11:20:29 arch-box systemd[1]: Unit [email protected] entered failed state.
Last edited by mvheart/dev/null (2014-08-18 15:50:10)

BIOS update fails on Satellite P100-429

Ive had a bad flash on my Satellite P100-429.
The utility crashed which left me with a bookend. Not happy
Ive created a floppy crisis recovery disk & bought a USB floppy drive after much hunting the internet for info.
Problem is I need verification on the exact key combination for my laptop to envoke crisis recovery mode.
On power up I have usual symptoms, flash of LEDs, power to CD-rom, power click of floppy drive etc...
I just need to verify correct sequence for key combinations.
Can anyone help?
Win-f, win-b, fn-f, fn-b, win-esc, fn-escape doesnt seem to work for me
How long to wait for floppy to start after combination etc?
Help!

Hi
I dont have experience with these BIOS recovery tools because in my opinion its a little bit too risky. This is no official way to recover a BIOS and I dont want to destroy the whole ROM module.
In my opinion if a BIOS update wasnt successful, you should go to an authorized service provider. Contact a notebook technician and explain your situation. The technician can try to reflash it and they have more experience. I think this shouldnt be a problem to contact one. ;)
Good luck!

My new iPhone 4 doesn't work at all

You are definitely not alone with your issues. I'm on my second iPhone 4 unit, and am still having the same problems. I've had proximity sensor insanity, battery draining after 8 hours of stand-by (NO USE, just sleeping) to the point that my phone goes into a coma and has to be plugged in to be revived, the grip of death dropping calls....
But the single most irritating and infuriating problem is the signal strength/reception fluctuation. I share a house with two iPhone 3Gs users, and I had an original silverback iphone until July 2010. They all work fantastically well with no issues when I'm at home (where I am just about 24/7, since I work from home). *_My new iPhone 4 doesn't work at all.*_. Signal strength is all over the place. I did a test where I sat watching the bars showing signal strength for five minutes. In that time, I saw it switch from E (edge?) with full bars to 3G with full bars to 3G with 1 bar to 2 bars to 4 bars to 1 bar to "Searching." Then back to 3G, with degradation of bars from 3 to none, then E network appears again, this time with full strength. This all with the phone sitting on a table, not being touched by human hands.
It seems that my iPhone is constantly switching actual physical networks, and as a result signal strength is all over the place from one 30 second period of time to the next. This drains the battery like crazy, and means that all incoming calls go to voicemail--usually without my phone ever ringing.
The 3G phones in my house work great. The 1st G iPhone I have had since the week it came out worked great (though its battery doesn't hold much of a charge anymore, after three years). On my new IP4, games are awesome. The videos and photos are amazingly clear and high quality, and editing on the phone is out of sight. iPhone Apps rule. MobileMe syncs my contacts quickly and easy. The only thing I love more than the iP4 features is my iPad--it rocks.
Everything works on my IP4 at home BUT THE ACTUAL TELEPHONE FUNCTIONS. This is unacceptable. In late August, after two weeks in which I had 4 minutes of phone use, the nice folks at the Apple store switched me to a new phone, no questions asked. The phone worked so much better, I could send texts and place calls most of the time (this was now the first part of September)...except that now that I was using my IP4 to make phone calls, I started having a problem with the proximity sensor during those calls. I'd be talking and my cheek would mute the phone, turn on speaker, open contacts and edit info (with gobbledygook), and of course, hang up on people.
So around Sept. 18 I was told by Apple phone support to update to iOS 4.2, restore as new, and do two complete power up and drain down cycles. This would fix the proximity sensor and any other issues.
Well, I would love to see if iOS 4.2 actually did fix the PS, but I can't get the signal strength to stabilize long enough to have an actual phone conversation. I'm back to watching the signal strength go up and down at random (with me touching/holding it carefully to avoid grip of death, and also when I leave phone on the table with screen lock off --no touching). It is back to switching between E network and 3G and varying strengths of wi-fi from my home network. This eats up battery from 100% to low enough to turn off in under 10 hours of standby (usually 6-7). Essentially, my IP4 is back to being unusable as a phone.
So I did another long, involved call to Apple tech support on 9/18. They tell me that I have to turn off wi-fi, turn off 3G, turn off push/fetch and notifications, shut all apps (no multi-tasking) and do everything but switch my phone to airplane mode--and see if the battery holds up for 24 hours in standby. If that didn't work, I should restore from new, but not load any contacts or network or data or anything--just leave it as it would be out of the box new.
As a test, I turned everything off as advised: 3G, wi-fi, push, etc. Now my battery life is back to normal, where I can have the IP4 on stand-by for up to two full days before needing a recharge. Fabulous. BUT IT'S NOT A SMART PHONE if I have to turn off 3G, turn off wireless, and not use email push and so forth.
I'm so frustrated I could scream. I'm quickly coming to the conclusion that there is a significant flaw in the new iPhone. Or perhaps it is just an issue for iPhone 4 users in areas where the signal strength is marginal, or where there are two types of overlapping network coverage (E and 3G in my case). I know that the networks themselves are in good condition--though I'm in a semi-rural area, the state capital is 4 miles away, and I know they have a new tower and good coverage for the politicians and power brokers around town. The phone coverage area I live in has Edge network in the south part of the network area and 3G in the north part, which is the state capital. I'm right in between. Could this be the problem? AT&T says no, it's Apple's fault.
Message was edited by: HighSierra

So what to do besides complain? Troubleshoot?
I just wonder if all of us who have had chronic signal strength and "Searching for network" issues that totally drain the battery might have something in common, despite being all over the world? I'm using wi-fi 95% of the time, and live in a semi-rural area with overlapping networks run by same carrier. Apple folks hinted that maybe in my area the network usage is nearing capacity (resulting in getting kicked off of 3G and down to E as new calls are placed that strain capacity). They also hinted there could be interference from mountains or other objects. But here's the thing--3G phones work fine, and my IP4 works fine when I'm away from home, usually in the capital city on strong 3G network. (When I say "works fine I mean the signal is good and calls go through, I haven't tested battery drain away from home yet).
I have to conclude that the problem is the IP4 itself--something about the hardware or the software (namely, the way it connects to the phone network) is horribly wrong. Other folks who live in urban areas or with strong networks that (likely) aren't over-utilized don't seem to have this issue. After reading through these pages, it also seems the wi-fi may be a major culprit in draining the battery and in varying signal strength (this is from Apple phone support, which said that varying signal strength and the constant pinging off the home wi-fi is creating a "power struggle" and keeping the phone constantly looking for the best connection option). Mind you, 3G iphones on the same home network have no problems whatsoever.
So while I'm not a technical expert, it seems like the problem HAS to lie in the differences in the way the IP4 connects to the cellular and/or wi-fi network. And since the connection/signal strength problem was "resolved" on my replacement phone, but then "broken" again by the software update of iOS 4.2, I'm leaning toward this being a software issue. I've offered to help Apple troubleshoot, and I'm trying to be patient--because the IP4 is a work of art and I've never had an issue with an Apple product before. But all they want me to do is restore, restore, reload, restore, and then drive 1 hour to the nearest Apple store (in Reno, NV) and get a new phone...and start the whole process over again. I don't have time for this, I need my phone back.
I'm this close to trading in my beautiful but flawed IP4 for a 3G. Maybe I should just get a new battery for my original iPhone from 2007?
I understand that Apple can't test for every possible variable of use all over the world, but they don't even seem to acknowledge that they have a problem with the IP4 that will not be resolved by replacing it with a new unit. They want me to believe it's a fluke, or it's just me...but I've been combing these threads and see a lot of people reporting the same issues I am--battery drain and wildly fluctuating signal strength issues, wi-fi problems, and dropped calls. Can't someone get on this? Because otherwise Apple is going to have to admit that their IP4 is not a good solution for people who live in areas of less than perfect signal strength or use wifi or whatever demonic combo I have in my home/work setting.
Or people will have to do what I have done--if you who want the cool IP4 non-phone features, you will have to dumb down your IP4 in order to have it be even moderately useful as *a phone.* For $599 I expected better.
My (temporary) workaround?
To spare the battery:
*Turn off wi-fi (which *****, because now I have to burn minutes when I'm at work using the email, downloads, safari, etc--and it's E network, so it's SLLOOOOOOOW)
*turn off push and fetch, have mail get new messages manually
*turn off data roaming
To keep the signal somewhat stable (making it easier to complete calls and spare battery)
*Turn off 3G (this leaves me on E network--fabulous, I had that with my 3 year old iPhone)
*grip IP4 between two fingers placed at the top of the phone, away from death zone. Tough for us lefty phone users.
*pray the free bumper will a) come soon and b) help. I'm not optimistic.
To keep proximity sensor from going nuts and dropping calls, muting, turning on speaker etc:
*use headset or bluetooth (unless you are also having one of the known bluetooth issues!)
*keep phone pressed to one ear and don't move it a millimeter. Don't shift sides, don't hold phone with your shoulder, just keep it to one ear and talk fast).
I'm about out of patience. I understand that lots of folks have and love their IP4s. I'd love to be one of those people. I'm open to suggestions and have spent many hours on phone with tech support, restoring my phone, reloading data and apps--there has to be a better way.
Sorry for the thread-jacking, but someone from Apple has got to be following these threads--help us!
null

P20-552: 2GB SD card doesn't work.

I have a P20-552 (PSP26E-025E9-S4) which is about 18 months old. I recently bought a Canon digital camera (IxUS 750) with a 2GB Sandisk Ultra II SD card and the combination is working well. Although I can transfer images from the camera to my Toshiba portable using an USB cable, sometimes I would like to use the SD slot on the portable but there seems to be a problem: seconds after pressing home the SD card in the slot I get the message "Disk is not formatted - Do you want to format it now?". I reply OK but then I get the message "The disk in drive E cannot be formatted"
The card continues to work perfectly well in both my camera and in my iPaq PocketPC. The SD card slot in the Toshiba will work quite happily with the Sandisk 256MB SD card that is usually in my PDA.
Anybody has any idea why the 2GB card doesn't work in the Toshiba? Is it a question of updating a driver - I did look the other day but I couldn't find anything that to me seemed appropriate but I might well have overlooked something..
I am running XP Home (SP2) and have fully automatic updates ON. I have Norton Virus and Zone Alarm running and am not experiencing any problems with any other software/applications - at least, no problem since someone suggested vacuuming my overheating laptop a few weeks ago ;-)
Thanks, Brian.

It seems that the unit doesnt support this card.
Check your user manual. There you will find a information that this unit supports only the following SD card sizes: 8/16/32/64/128/256 and 512 MB
According to this document the 2 GB are to high.

I have an iPhone and when I got it, I had a Toshiba laptop. Now I have a MacBook Pro, but when I try to wi-fi sync my iphone and new computer, it doesn't work because on my iphone it is still trying to sync with my old computer. How I can fix this?

I have an iPhone and when I got it, I had a Toshiba laptop. Now I have a MacBook Pro, but when I try to wi-fi sync my iphone and new computer, it doesn't work because on my iphone it is still trying to sync with my old computer. How I can fix this?

Move the content from the old computer to the new computer.
Sync the iPhone via cable to the new computer and enable Wi-Fi syncing.
It should now be possible to sync via Wi-Fi to the new computer.

My Card doesn't work anymore and keeps asking me for the card information. How do I turn the card option back to "none".

How do I turn this off? I can't download anything until I put in the card's information. But the card doesn't work anymore, it ran out of money. It keeps saying that my last perchase was unseccessful or something. I just want this to stop so I can update and download apps! Please help!

My iMac with Snow Leopard 10.6.8 crahed b/c the HD cannot be repaired. I reinstalled Mac OS X and luckily have most documents and applications. I have moved them all into folders before I erase the HD. I had all my documents but lost the 3 applications for iWorks. It says go to the store, buy and enter your serial#. That is not working. Here it is:MB966Z/A
WVL 001299 10959191-000
I need the updates. Apple has my sign in Apple ID.
Thanks,
pandaposyus

What do you do went your iTunes redeem card doesn't work ?, What do you do went your iTunes redeem card doesn't work ?

What do you do went your iTunes redeem card doesn't work ?, What do you do went your iTunes redeem card doesn't work ?

Welcome to the Apple Community.
The following article(s) may help you.
iTunes Card and Gift Certificate FAQ

HT1277 I cannot open the new email icon for 10.6.8 and the latest secrtoy update. My old "Stamp" icon email won't let me in either indicating that the new OS version doesn't work. Please help

I cannot open the new email icon for 10.6.8 including the latest security update. My old "Stamp" icon email won't let me in either indicating that the new OS version doesn't work. Please help. I have spend over 4 hours installing and reinstalling updates, etc. and I don't know where to go from here.....

Mac OS X v10.6: Mail.app won’t open, or "You can't use this version of Mail…" alert after installing Security Update 2012-004:
http://support.apple.com/kb/TS4424?viewlocale=en_US&locale=en_US
Fellow user Grant Bennet-Alder offers this solution:
Some users have reported this problem if the Mail Application has been moved out of the top-level /Applications folder, or duplicated in another location.
When the Security Update is done, the old version of Mail is disabled.
The solution has been to:
1) make certain Mail is in the /Applications folder
2) There is no other copy anywhere else.
3) Once steps 1 and 2 have been done, Manually download and re-apply the Security Update (2012-004) by hand.
Security Update 2012-004 (Snow Leopard)
If the Mail.app has been LOST, it can be re-installed by applying the 10.6.8 version 1.1 combo update. But this update is quite large and it is usually not necessary:
Mac OS X 10.6.8 Update Combo v1.1

Satellite P100-429 - New WLAN card doesn't work

Similar Messages

Maybe you are looking for