Satellite P100: Fatal Execution Engine Error code Ox7927e03e

The above error message (code Ox7927e03e) appears every time I restart my Satellite P100.
Various suggestions on the Microsoft XP website to update/repair Net.Framework don't work.
Any ideas? The computer works normally except for Media Centre which generates the same message.

You could firstly use the Windows own system restore tool. This tool will turn back the OS to the early point. If it does not work you could use the Toshiba recovery CD. On this CD everything was preinstalled and this installation will set the notebook back to the factory settings

Similar Messages

"fatal execution engine" error when launching labview--I just installed it?

I just installed Labview (I still have the CD in my computer) but when I double click the icon to start the program it starts the splash screen, but then issues an "internal execution engine fatal error." The only option to enter is into the JIT debugger. I have XP/SP2 and I have uninstalled my C/C++ compiler and my Ada Compiler, but I am still receiving the error. I have uninstalled Labview twice and reinstalled it, but still the same. The disk that I am installing is labeled 7.1, so I went to the website and downloaded 7.1.1 and installed it but still the same error. I tried to install Labview barebones (without drivers, CVI, etc...) but this didn't fix my problem either. I am out of ideas.
Ronnie_b

Hey Ronnie,
I know Marni personally, and I'm sure she's done her homework on this one. Unfortunately with this being an issue specific to your PC, it does sound like it might be one of those issues that is unidentifiable and seemingly "incurable" without reformatting. However, I'll double check with Marni tomorrow to make sure we've exhausted all possibilities before having you reformat.
I'll get back with you via this post.
Take care,
Travis H.
National Instruments
Travis H.
LabVIEW R&D
National Instruments

Re: Satellite Pro C870 - No Wireless, Error code 43

Have two new Satellite Pro C870's where the wireless was being disabled every second startup. Wireless NIC in device manager had an exclamation mark and was showing "Windows has stopped this device because it has reported problems. (Code 43)"
After performing a system restore as advised by support the issue was still there.
Just before sending the two laptops off for repair I undid a setting called "fast boot" in the bios (otherwise set using a Toshiba utility).
Issue seems to have cleared after this.

Hi
You are using Win 8. Right?
> Have two new Satellite Pro C870's where the wireless was being disabled every second startup
First of all you should know that Windows 8 does not perform a real shutdown.
It goes just in hybrid mode.
Maybe the error 43 is related to the fact the Win 8 and notebook did not shut down as you expected from a system like Win 7.
If you would search for error code 43 using google, you will get a lot of hits and mostly its system / driver issue.
So first of all I recommend disabling the hybrid mode and performing complete shut down:
+Perform a complete shutdown in Windows 8+
http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm
secondly try the WLan driver update.
Regarding the other issue
>Also had an issue with the function of turning on when the panel is opened: this would cause the laptop to turn back on immediately after shutting down.
This is also an Windows 8 feature which can be disabled:
+Why does my Windows 8 notebook start automatically when opening the display lid?+
http://aps2.toshiba-tro.de/kb0/FAQ2C03FA0001R01.htm

My Satellite C wont load Windows - error code 0xcoooooe9

Hi,
get a status error come up when the laptop is turned on. The error code is 0xcoooooe9, windows does not load up and the diagnostics tool does not work.
Tried to recover to factory settings but this crashed out saying partition could not be created and only had an option to turn the laptop off.
Was bought from argos's ebay store less than 12 months ago and should still be under warranty but can not find out if it is on here.
Any help please ??
Message was edited by: MasterG

On this virtual way it is not easy to say what the problem is but maybe HDD make problems.
I recommend you to contact nearest Toshiba service provider and ask for help. They can check it.
At first clarify the warranty and I hope they will fix it for free.
Phone numbers and addresses you can find on http://www.toshiba.eu/innovation/generic/ASP_SUPPORT/

Satellite Pro L300 - DVD drive error code 10 on Vista.

Can't see DVD drive on "my computer" Under device manager its showing drive but with yellow triange, after looking at info, the device status is "This device cannot start. (Code 10)" tried restarting 2 times. Thats not working.
Also cheaked drivers, on my computer and internet, windows is saying there up to date and im running the latest.
Tried to uninstall drive and restart thats failed.
When instering a disk the drive does move and spin the disk, so im hoping its a technical issue and doesnt need new drive.
Any help is welcome
thanks

Hi mate
Dont worry it seems its just a registry issue.
First of all remove the CD/DVD drive from the device manager list.
Then go to registry and remove the Upperfilters and Lowerfilters values completely from the following registry key:
+HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contr ol\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}+
Details here:
http://support.microsoft.com/kb/270008/en-us
Then reboot the notebook.
Wait until the OS has recognized the CD/DVD drive again and check it.
Greets

VI Logger crashes during data acquisiton, Engine error, code -2144767259

see information above and .jpg
Attachments:
NI_Error.jpg ‏40 KB

Using VI Logger, I"m trying to log two analog channels off of a digital trigger. The task will start and run, but once the digital input is triggered to start the logging, the error window pops up (see original post for window). I have two logger tasks and it happens on both of them, so it is not isolated to just one virtual channel. Do you require any more information?

Error message for liveupdate engine COM module - Satellite P100

I have a Satellite P100 using Windows Vista home premium, and upgraded cable internet plans with Optus over the weekend to the Fusion89 plan.
Since then internet has been slow to open (up to 25 seconds when I click on a new tab), and attachments are slow to open from E-mails.
I also keep receiving an error message from Microsoft Windows stating "liveupdate engine COM module stopped working and was closed. A problem caused the application to stop working correctly. Windows will notify you if a solution is available".
I have contacted Microsoft who said they would help me for a fee, but as I have the laptop under an extended warranty, they suggested I contact the people I bought it from or Tochiba. Before I contact Clive Peters soes anyone have any comments or suggestions regarding my issues?
Any assistance will be much appreciated.

Try this:
Go to a Command Prompt and run "CHKDSK C: /F"
Run WindowsUpdate / update Internet Explorer
Try disabling your Antivirus software or Firewall software.
If you installed Optus/connection software, update the software.
Ensure the ISP (optus) proxy settings are correct in IE and the email software.

Intel Trusted Execution Engine Interface has a Code 10 error.

When I open Device Manager I get a yellow triangle on the Intel Trusted Execution Engine Interface. I open it and it says
This device cannot start. (Code 10) STATUS_DEVICE_POWER_FAILURE. I have tried uninstalling it and updated all drivers. I don't know what else to do so it will be awesome if anyone can help me out here.

You're very welcome.
OK...
Let's try manually installing the driver.
First, go to the Intel TXE driver folder you unzipped and open that folder.
Inside that folder there is another zipped driver folder (KMDF whatever). Unzip that one. Let it extract inside the other folder.
Go to the device manager and click on the problem TXE device.
Then click on the driver tab.
Click on Update Driver.
Select the browse my computer for driver software option and then at the bottom of that window, select the Let me pick from a list of device drivers on my computer.
Select Have Disk and browse to: unzipped Intel TXE driver folder\unzipped inner folder\KMDF_NO_RTD3_DRIVER\KMDF_NO_RTD3_DRIVER\NO_RTD3_DRIVER\release\x64\TXEI, and select the Intel(R) Trusted Execution Engine Interface device from the list and see if the driver installs that way.

Installer LV7.1 - LabVIEW load error code 21: An external subroutine required for execution could not be found.

Bonjour,
Je cherche à créer un installer portatif utilisant les drivers NI-DAQmx 8.7.1 et NI-CAN 2.6.0.
Je dispose d'un code LV 7.1 et j'ai installé l'application builder 7.1.
Mais une fois l'application installé sur un PC vierge de Labview, j'obtiens le message suivant:
load error code 21: An external subroutine required for execution could not be found.
Ce message est répété plusieurs fois (pour différents VIs) puis le programme ne se lance pas.
J'ai bien veillé à installer les drivers NI-CAN et NI-DAQmx correspondant au préalable sur la machine cible.
En chercant sur le forum, plusieurs pistes m'ont été proposé:
La version NI-DAQ
L'intégration du Run time Engine
Un problème de DLL
J'ai vérifié ces 3 points mais cela n'a pas règlé mon problème.
Résolu !
Accéder à la solution.

Bonjour,
Merci de ta réponse.
En fait, j'ai bien inclu le runtime engine de Labview qui était effectivement la source de l'erreur.
L'installation de NI-DAQmx v 8.7.1 provoque la mise à jour de la version du runtime engine (passage de 7.1 à 7.1.1).
J'ai donc désinstallé Le runtime engine 7.1.1 (ce qui a provoqué la désinstallation de labview et NI-DAQ).
Puis je suis passé par une version plus ancienne de NI-DAQ (7.2) que j'ai adapté (inclusions de DLL et de VIs).
Les messages d'erreurs ont alors tout simplement disparus!

Adcfgclone.pl error:RC-50014: Fatal: Execution of AutoConfig was failed

hi all,
i got following error while cloning of R12 instance on HP UX.
after copying from source to target i have run perl adcfgclone.pl dbTechStack.
error...
Starting synchronization of file system Context file and its templates with those in the database
Database connection : Failed
OAM Context editing support feature: Unverified
OAM Customization support feature : Unverified
File system template : /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/template/adxdbctx.tmp
No uploading of Context file and its templates to database. Database conection failed
[AutoConfig Error Report]
The following report lists errors AutoConfig encountered during each
phase of its execution. Errors are grouped by directory and phase.
The report format is:
<filename> <phase> <return code where appropriate>
[INSTANTIATE PHASE]
AutoConfig could not successfully instantiate the following files:
Directory: /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/install/RSU_reeldev
adcrdb.sh INSTE8
AutoConfig is exiting with status 1
RC-50014: Fatal: Execution of AutoConfig was failed
Raised by oracle.apps.ad.clone.ApplyDBTechStack
regards,
sandeep.

hi,
i already have checked <RDBMS ORACLE_HOME>/appsutil/log/<Context_name>/<MMDDhhmm>/adconfig.log location but there is no directory with <MMDDhhmm>/adconfig.log..
can u check below update....i think i m missing some syntex
adcfgclone.pl dbconfig /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/RSU_reeldev.xml
Copyright (c) 2002 Oracle Corporation
Redwood Shores, California, USA
Oracle Applications Rapid Clone
Version 12.0.0
adcfgclone Version 120.20.12000000.12
Enter the APPS password :
Running Rapid Clone with command:
perl /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/bin/adclone.pl java=/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/bin/../jre mode=apply stage=/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone component=dbconfig method=CUSTOM dbctxtg=/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/RSU_reeldev.xml showProgress contextValidated=false
Running:
perl /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/bin/adclone.pl java=/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/bin/../jre mode=apply stage=/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone component=dbconfig method=CUSTOM dbctxtg=/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/RSU_reeldev.xml showProgress contextValidated=false
APPS Password :
Setting SHLIB_PATH to :/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/oui/lib/hpunix
Beginning dbconfig Apply - Sat Apr 24 12:19:55 2010
/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/bin/../jre/bin/java -Xmx600M -DCONTEXT_VALIDATED=false -Doracle.installer.oui_loc=/erpdev1/orarsu/db/tech_st/10.2.0/oui -classpath /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/xmlparserv2.jar:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/ojdbc14.jar:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/java:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/oui/OraInstaller.jar:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/oui/ewt3.jar:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/oui/share.jar:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/oui/srvm.jar:/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/jlib/ojmisc.jar oracle.apps.ad.clone.ApplyDatabase -e /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/RSU_reeldev.xml -stage /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone -rmanstage -rmantgtloc -srcdbname -showProgress -checkDBConnection
-e
/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/RSU_reeldev.xml
-stage
/erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone
-rmanstage
-rmantgtloc
-srcdbname
-showProgress
-checkDBConnection
Option -rmanstage can only appear once
usage:
java oracle.apps.ad.clone.ApplyDatabase
-e CONTEXT [-stage STAGE_DIR]
[-stagestub STAGE_STUB] [-verbose]
[-rmanstage RMANSTAGE]
[-rmantgtloc RMANTGTLOC]
[-srcdbname SRCDBNAME]
[-nthreads NUMBER] [-showProgress] [-pwd PASSWD]
[-phase bits|reg|cfg|all]
[-node initial*|add|remove] [-shared]
[-dbmode clone*|restore|standby]
[-checkDBConnection] [-configracnode]
where:
CONTEXT = Applications context file name
STAGE_DIR = Cloning stage directory
Only used if running 'Copy Bits' phase.
STAGE_STUB = Custom stage sub directory
Only used if running 'Copy Bits' phase.
-verbose = if specified, will run in verbose mode
NUMBER = Number of threads used in the zip action. Range [1-20]
showProgress = Shows the progress of the process
bits = process only the 'Copy Bits' portion of the clone
reg = process only the 'Registration' portion of the clone
cfg = process only the 'Configuration' portion of the clone
all = processes 'Copy Bits', 'Registration', and 'Configuration'
initial = (default value) runs process for creating initial node
add = runs process for creating initial node
remove = runs process for creating initial node
shared = Used for shared filesystem nodes.
Verifies and uses bits that are already present.
Only used if running 'Copy Bits' phase.
clone = Standard cloning mode where the new database is brought up
with a new DBID and Global DB Name. Clean-up and setup
processes may be started
restore = Used to restore a database. DBID, GDBN, and
setup information are not changed.
standby = Used to create a standby database. Database is
not opened and no changes are made.
checkDBConnection = Checks for DBConnection before configuring
configracnode = used for scale out on a RAC instance
ERROR while running Apply...
Sat Apr 24 12:19:56 2010
ERROR: Failed to execute /erpdev1/orarsu/db/tech_st/10.2.0/appsutil/clone/bin/adclone.pl
Please check logfile.
pls help me to resolve the same...
thanks
sandeep

Fatal execution error

When I start-up my computer I receive a Fatal execution error 0x7927f26e notice. I can continue but would like to prevent the notice from happening. What's going on?

I have tried following suing start /wait
start /wait xcopy "IBM LUM Directory" "C:\ProgramData\" /E /C /R /H /K /Y
1\win64\startb.exe -u "c:\program files\Dassault Systemes\R18" -newdir -ident R18 -D "C:\ProgramData\DassaultSystemes\CATEnv"
-l "DIC.slt" -v -noreboot
same results, deployment failed with exit code 55 and slight different error
IMaintenanceCodeinator::GetState failed with error code 0x87d00317
Monitoring status is In Progress..
RJ09

What does this mean? Server Message: Unable to load server - system error code: 0x80080005, CO_E_SERVER_EXEC_FAILURE: Server execution failed.

This is the error that we get when we run the Tag File.
ERROR 04/16/2004 02:26:15 PM Server ERROR from Server: National Instruments.OPCLookoutDrivers. Status: -196608, Server Message: Unable to load server - system error code: 0x80080005, CO_E_SERVER_EXEC_FAILURE: Server execution failed.
What does it all mean?

ACRE,
this looks like the Industrial Automation OPC Server (Lookout OPC) is not correctly installed or configured and therefore the DSC Tag Engine - as OPC client - cannot launch the OPC server correctly.
Two checks I have in mind.
- Installation check: Check if the Industrial Automation Server is installed and configured correctly and that you will have a .lpd file as default. Could it be that the .lpd file is corrupted? BTW - what kind of protocol are you using and did you configure aliases for the LPD object? A good resource on checking the configuration might be the online help of Industrial Automation Server (Lookout Protocol Drivers) or the link penDocument>How Do I Configure My Devices with Lookout Protocol Drivers?
- Access rights, COM/DCOM problems: Can you launch the OPC Server with another OPC client? Is your OPC server running locally? If you don't know how to check on this I found a good KB Tools for Troubleshooting OPC Interface Problems E.g. can you access it with Server Explorer?
Last question... did you encounter this problem recently while it was working before? What changes have been done on your system?
Let us know if you have some questions and I hope some of the links help you further troubleshooting this issue.
Roland

Catia V5R21 package deployment on windows 7 x64 doesn't complete - Non fatal execution error 0x87d01100

I am trying to deploy Catia V5R21 on windows 7 x64 machines, deployment starts but doesn't not complete using sccm2012 R2
I can deploy software to windows 7 32bit machine fine using sccm2012 R2. Also manual install on windows 7 x64 works fine.
here is the script I am using-
cmd /c install.cmd
xcopy "IBM LUM Directory" "C:\ProgramData\" /E /C /R /H /K /Y
1\win64\startb.exe -u "c:\program files\Dassault Systemes\R18" -newdir -ident R18 -D "C:\ProgramData\DassaultSystemes\CATEnv" -l "DIC.slt" -v -noreboot
I can see files copied over client machine and "c:\program files\Dassault Systemes\R18" get created, also an entry appear in control panel>programs and feature.
Problem I am having is deployment doesn't complete.
I checked logs under Execmgr.log on client machine and found errors
Raise Program Error Event for program Catia. The exit code is 55, the execution is FailureRetry
Non fatal execution error 0x87d01100 encountered for program Catia V5R21
I can't see program installed under All Programs and SCCM monitoring status stuck in progress
Any help will be greatly appreciated..
Thanks in advance
RJ
RJ09

I have tried following suing start /wait
start /wait xcopy "IBM LUM Directory" "C:\ProgramData\" /E /C /R /H /K /Y
1\win64\startb.exe -u "c:\program files\Dassault Systemes\R18" -newdir -ident R18 -D "C:\ProgramData\DassaultSystemes\CATEnv"
-l "DIC.slt" -v -noreboot
same results, deployment failed with exit code 55 and slight different error
IMaintenanceCodeinator::GetState failed with error code 0x87d00317
Monitoring status is In Progress..
RJ09

Satellite C850-1NU does not boot Win 8.1 - Error Code 0xc0000098

Windows 8.1 will not boot
Laptop is *Toshiba Satellite C850 1NU*, as from Saturday it will not boot up!
*Error states "The boot configuration Data File doesn't contain valid information for an operating system.*
*File:\ BCD*
*Error Code 0xc0000098*
I have transferred recovery tools from another laptop to a USB stick and then enter bios of the Toshiba Laptop to make the USB drive to boot first.
It then comes up with the recovery tools.
I clicked on "Refresh your pc" it then reports "The drive where Windows is installed is locked. Unlock the drive and try again".
I clicked on "Reset your pc" it then reports "Unable to reset your pc. A required drive partition is missing".
I have also tried "Automatic Repair" and it reports "Repair couldn't repair your PC".
I am at a loss as to get my sons laptop up and running again. Advice would be much appreciated. Thank you.

Further to my question, *I have now resolved the issue.*
Thanks to phanlon7 on this link
[http://answers.microsoft.com/en-us/windows/forum/windows_8-system/windows-crash-refresh-hard-drive-locked-unlock/a6bb04ff-5dba-4e10-a849-644cd0851bc6?page=2&rtAction=1390385080363]
I used a usb stick and copied recovery from another windows 8 laptop.

Satellite A40 - Error code 10- D: drive cannot be found

HELP PLEASE!!!
I really need some help to fix the errors on my system.
A short while ago i accidently deleted the DVD+/- optic drive to my laptop, and when I go to my computer it isnt there?
The sys. tells me that the D: drive cannot be found, and the drive was removed without preperation and cannot be found, Error code 10.
What does this mean, as I have tried to update the BIOS, and it does not need it, and i cannot find a driver for the Satellite A40 from Toshiba.
Also the drivers appear to be ok and the boxes are ticked in the device management, altho the optic drive sometimes has a yellow exclamation mark?
Tried the recovery disk and no luck.
Also the drive doesn't work now, as it doesnt read disks!
Here is the spec. for the computer, and the summary for the error messages. Wouild reallr appreciate any help on this please . . . .
My Computer Information - General
Please wait while information is being collected...
100% (collecting Local Disk information)
Refresh screen
Specifications
TOSHIBA
System Model: Satellite A40
BIOS Version: TOSHIBA Version 1.50
Operating System
Microsoft Windows XP Home Edition
Version: 5.1.2600
Service Pack: 1.0
Location: C:\WINDOWS
PID: 55277-OEM-0011903-00111
Hot Fix: Q817606
Memory (RAM)
Capacity: 2 GB
Here is a listing of the Dr watson error reports that appeared don the system.
25 January 2009 Service Control Manager The Application Management service terminated with the following error: The specified module could not be found.
25 January 2009 atapi The device, \Device\Ide\IdePort1, did not respond within the timeout period.
25 January 2009 Cdrom The driver detected a controller error on .
25 January 2009 atapi The device, \Device\Ide\IdePort1, did not respond within the timeout period.
25 January 2009 Service Control Manager The following boot-start or system-start driver(s) failed to load: Cdrom
25 January 2009 PlugPlayMa nager The device 'T S I A D D-R M S - 6!1"' (IDE\CdRomT_S_I_A_D_D-R_M_S_-_ 6!1"________________1#3"____\3 423362730283321372620202020202 020202020) disappeared from the system without first being prepared for removal.
31 January 2009 Cdrom The driver detected a controller error on .
31 January 2009 Service Control Manager The following boot-start or system-start driver(s) failed to load: Cdrom
24 January 2009 Applicatio n Error Faulting application helpctr.exe, version 5.1.2600.1106, faulting module kernel32.dll, version 5.1.2600.1106, fault address 0x0001a67a.
25 January 2009 MsiInstall er Product: ParetoLogic DriverCure -- Error 1722.There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor. Action DeleteScheduledTask, location: C:\Program Files\ParetoLogic\DriverCure\D riverCure.exe, command: -deletetask
25 January 2009 Applicatio n Hang Hanging application switch.exe, version 0.0.0.0, hang module hungapp, version 0.0.0.0, hang address 0x00000000.

Run Regedit, and remove the Upperfilters and Lowerfilters values from the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class{4D36E965-E325-11CE-BFC1-08002BE10318}
Then Reboot. If your CD/DVD burning software fails to work, reinstall that software.

Satellite P100: Fatal Execution Engine Error code Ox7927e03e

Similar Messages

Maybe you are looking for