Satellite P100: USB/Fire-Wire ports not charging external device

When I plug my ipod into either my 4 pin fire-wire port or a USB port on my laptop (satellite P100) it fails to charge, even when plugged in to the mains/ A/C power. I think I have found where I need to go in 'control panel' but need help on how to allow my fire-wire and USB ports to give out power and charge my ipod when its connected.
Any help on this matter will be greatly appreciated.
Cheers

Hi
The USB ports provide automatically the power. Usually every USB port provides about 500mA.
But please note; the notebook must run and the external USB device (iPod) must be recognized by Windows OS!
I dont know if the iPod was recognized by WinOS but I have read the many users have problems with the iPod installation on Windows OS. As far as I know the iTunes must be installed if you want to use the iPod.
Greetings

Similar Messages

Display's fire wire port

Just bought a new mini with a 20 in Mac display. Since the only fire wire port is taken on the mini with the display wire, can you use the displays fire wire port for the external hard drive? Thanks

If you have only one FireWire device, you can plug it into the Mini, and leave the display's FireWire cable disconnected. If you have two devices, or the display's FireWire ports are in a more convenient location, plug the display's FireWire cable into the Mini and use the FireWire ports on the display.

How do I connect Apple 20" Cinema Display to orignal MacBook Air which does not have a Fire-Wire port. Is this possible? Any advice would be appreciated. I have the Micro-DVI to DVI adapter. Norm

I Wish to connect my 6 year old Apple 20" Cinema Display to an orignal MacBook Air which does not have a Fire-Wire port. Is this possible? Any advice would be appreciated. I have the Micro-DVI to DVI adapter. Norm

The FireWire cable is just for the FireWire ports on the display. The display will run without it.

Fire wire ports do not work

Here's a little history with the problem I'm having. At first (about 1 year ago) my fire wire ports became intermittent. They would work one second, then they wouldn't. I took my Mac in to be serviced, at the time it was still under warranty, but the techs couldn't find anything wrong. I brought it home but still had the problem. I figured maybe my components were bad. 1 year later I'm still having the problem. So I took it back, to the same people, this time they dug a little deeper with their tests and found that my logic board was bad. Everything else on the computer seems to work great, just not either fire wire port.
The questions I have are:
1) has anyone encountered this problem?
2) when looking at the logic board which number is used for the part
number? Mine says 820-1592-A, also 630-6483 is listed just under the
bar code. I'm trying to locate another, so far unsuccessfully.
3) do you think Apple would honor the warranty since Authorized techs
didn't find the problem the first time when my MAC was under warranty?
Any info will be helpful. Thanks

I had an issue with my FireWire ports not working right before my logic board died. I was able to resurrect the FW situation by unplugging everything from the back of the G5 (including the power cord) and letting it sit for 15 minutes. This caused a reset and then FW started working again -- alas for nothing when the logic board croaked a few weeks later.
By all means contact Apple -- since you did have it checked under warranty they might be able to work with you. You have nothing to lose and a lot to gain. My repair put me back $900 + (I did not have an AppleCare extended warranty, since I have never had any of my previous Macs fail before).

20" Cinema display with USB and firewire ports not working

I have a new 20" display and was wondering why my USB and fire wire ports at the back are not working. I have an external drive that is powered hooked up to the fire wire port and a no powered piano keyboard to a usb port.
Any help please

Verify that the display’s USB and FireWire cables are firmly plugged in to the
computer. Do they show in your profiler?
Try different ports in the computer.
Verify that your computer ports are working with other known problem free device.

Fire wire 800 not working on IMAC

My Fire wire port on my IMAC 24 inch is not working now. I have tried switching cables, etc. This started when I had to have the hard drive replaced. The drives do work if connected by USB or FW 400.
John

Have you reset your SMC and PRAM? If that doesn't get your FW800 port going, run the Apple Hardware Test to see if it spots any hardware problem.

Do all maxtror drives have 2 fire wire ports

Hi all,
Im trying to buy a hard drive (maxtor seem to have been good to me so far) they have a new one called ONE TOUCH 3 but I cant seem to find out if they have 2 fire wire ports.
All the spoecs say this
"We stock 300GB and 500GB version with both USB 2.0 and Firewire 400 interface, please select storage capacity at the bottom."
Any tips ?
T
Thanks in advance
justin

If you are planning on using this for video work you should look elsewhere. It is not designed for that application.
If you are looking for a drive to simply back up data, it should work.
Generally recommended drives for DV and HDV include: G-tech & Granite Digital. Both of them make highly engineered drive solutions and include Hitachi mechanisms.
If you are thinking of working with uncompressed footage, then much more specialized drives/enclosures/connections are required.
good luck.
x

Fire wire ports driving me batty

I have a late 2007 Intel iMac with a total of 7 Lacie external hard drives daisy chained together via the 800 fire wire ports. The externals are stacked one on top of the other. I cannot hook up the 8th hard drive to the 7th one (the hard drive on the top is #1, the one on the bottom is #7) without losing the 7th hard drive (I get an error message saying that the #7 hard drive hasn't been disconnected properly) and it disappears from the desktop. However, if I attach the 8th hard drive via the 400 fire wire port, all is well. I've switched the order of the hard drives and used different cables, but it always seems that the 7th hard drive has an issue with both 800 ports being used. Anyone have a suggestion (other than hooking up the 8th to the 400 port) or an answer to why this is happening? I think maybe heat might be a factor.
Message was edited by: Sunny's mommy

I don't think the hard drives have internal fans. Anyway, I've tried switching the order, like hooking up #1 & #2, with #2 on the bottom, then hooking up #7 to #2. Changed around the order - sometimes it works and sometimes it doesn't, but it's pretty consistent, that whenever one of the two 800 firewire ports on the bottom one is in use and I attach another hard drive to the free firewire port, it freaks out the bottom one. However, when I use the 400 firewire port, all is well. Anyway, in the grand scheme of things, I'm not going to lose sleep over it. Was just wondering if it's the way I'm setting things up. By the way, what is a bridge board?
Message was edited by: Sunny's mommy

How can i download video hdv minicassette footage from my sony video camera with no fire wire port?

How can I download video HDV minicassette footage from my sony video camera with no fire wire port?

Hi,
Are you talking about your computer which has no firewire port ? If YES you can have one of two options:
(a) Use FCI - Firewire card like this (preferred)
You can buy from this:
http://www.ebay.com.au/itm/2-Ports-PCI-Express-PCI-E-IEEE-1394A-Firewire-Adapter-Cable-Card-/1507023...
(b) You can also use USB-Firewaire adapter like this:
http://compare.ebay.com.au/like/120580625092?ltyp=AllFixedPriceItemTypes
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

No power from Fire Wire port to my audio interface

I face this problem after my set-up always has worked: I have a Quata Fire 610 Audio interface, powered thru my Fire wire 400. For some reason there is no power, and my Mac does not recognize the unit. I have tried both Fire Wire ports, and none of them works. The unit works fine on my other Mac (iMac G4) Is there any way I solve this problem. I have done the the disc utilities.
Peter

FireWire ports have been known to fail.
Did you shut down (power OFF) the Power Mac G5, and restart? Did you also try the port on the front panel? Did you try a different FireWire cable? Is it possible to try another FireWire device on the ports, as a test?
You can also try a reset of the PMU or SMU (power management). Depending on your model
http://support.apple.com/kb/HT1436 <- newer models
<a class="jive-link-external-small" href="http://">http://support.apple.com/kb/HT1939 <- older models

Video out fire wire port from iTunes?

Final cut and Pro Tools LE both have the ability to send video from a G5 to a TV out of the fire wire port via a Canopus ADVC-110. Why doesn't iTunes? I understand that the new Mac TV gizmo plus an airport card will do this, but I already have all the hardware I need for this to work. I just need iTunes to take advantage of the same external video option that Final Cut and Pro Tools LE have. Anyone know of a patch or something that would make this happen. Or at least a stand alone player that will play the m4v iTunes video files and play video out fire wire port to my canopus which will then send it to the TV?

In an attempt to get my iTunes downloaded TV episodes to play on my TV without having to buy the Apple TV hardware and an airport card I have been trying to find a way to convert the m4v video files into a format that can be read by a stand alone player that allows me to output video playback through my fire wire port so my canopus box can then send it to my tv and stereo. I tried iSquint and it does not work. I get an AppleScript error "Can't make "" into type real. (-1700)" If you hit OK the program then spins it's wheels with the progress report "Preparing Audio for File 1..." It is still my belief that Apple should enable iTunes to output video through the fire wire port. Since Final Cut Pro and Pro Tools LE have that ability and it works I assume that it should work wth iTunes. Please send iTunes feedback from within iTunes and ask apple to add this option to iTunes.

Testing fire wire port

I have tried several times to test my fire wire port on this mac mini. I tnever does anything differently than boot up.
I am hooking up an audio interface and cant seem to get it to recognize the unit. I have tried testing the port, different cables and even purchased a 2nd interface thinking my original was the problem
Help
Mac Mini
M box pro
pro tools 10
Chase

Just for the record, I have friends that have the exact same setup as I do. It works flawlessly. They are using the same OS in both pro tools and apple. This seems to be a hardware connection issue. My Mac Mini does not recognize the M Box Pro audio interface I am using.
I have 2 m box pros doing the same thing. I have used 3 fire wire cables.
I first want to test the fire wire port on the mac mini, I need to know if it works at all. I tested it once and have not been able to conduct the test again. I believe this is some sort of internal set up issue. All of the software and hardware is identical to what several friends have.

One Fire Wire Port, What Do I Do?

I only have one fire wire port on my MacBook. I use that for the external hard drive/scratch disc when working in FCE. How can I capture video from my camera and then transfer to the scratch disc manually? The better question may be can this be done?

I don't know whether these 2 heretical comments will be of any use but here goes.
1. Whilst I generally use FireWire Hard Drives, I have never experienced any problems whatsoever, capturing or editing on USB 2.0 HDs (I have 3).
2. A few weeks ago I discovered to my surprise that I had been capturing DV and HDV from 3 different cameras (2 Panasonics and a Canon) through a cheap Belkin FW hub onto FCE 4 and FCP 6 for the last 18 months. I had wired it in to test whether it would work and then completely forgot about it.
However, although these things have worked perfectly on 2 computers and with 3 cameras etc. for me, I cannot guarantee they will work for everyone.

Lightning charger port not charging

Hi,
I have an iphone 5 64gb which has gotten progressively worse at charging up. It seems to need charging several times a day (top up) and when I do plug it in to a genuine apple charger it won't charge. It will only do so if I apply a little pressure to the collar of the charger itself leading into the phone. This means either standing there like an idiot whilst waiting for some charge of trying to set up some kind of method with a pen and a weight to keep the angle right. I have several chargers and all of tem do this so I am confident it it my phone rather than the charger. My phone is over 1 year old and will no long er be covered on warranty. I was considering taking it to apple and hope they might offer me a new i[phone 5 in exchange for the old one plus a bit of cash (as they have done before). It's annoying as the phone is not even two years old and the battery seems defunctand the charger itself is also on it's way out. Any ideas from anyone? Obviously I've blown into the charging void to remove any foreign objects and given it a cursory clean etc. Have i missed anything?
Thanks guys

Hi mattpuss,
If you are having an issue with charging your iPhone, I would suggest that you troubleshoot using the steps in this article -
iPhone and iPod touch: Charging the battery
In particular -
Inspect the connector at the bottom of the phone:
Make sure that there are no bent pins in the connector.
Make sure that the connector is free from debris.
If there are bent pins or debris, please contact Apple Support.
Otherwise, continue troubleshooting.
Make sure that the outlet you're using works.
Make sure that the Apple USB cable and Apple USB power adapter work.
Plug the device in to power and let it charge until your device turns on. This could take between 10 and 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
If the device still exhibits an issue, try turning your device off and then on again while connected to power.
If the issue persists, please contact Apple Support.
Thanks for using Apple Support Communities.
Best,
Brett L

HT2498 how do I find out what kind of fire wire port I have on my desktop? I want to transfer video from my camcorder.

how do I find out what kind of fire wire port I have on my desktop? I want to transfer video from my camcorder.

If you have Firewire 800 it's a boxy looking port, the Firewire 400 is thinner and has a arrow looking shape, you can get a adpater.
FW800 is simply FW 400 x 2, so the adapter gives you FW 400.

Satellite P100: USB/Fire-Wire ports not charging external device

Similar Messages

Maybe you are looking for