Satellite P200-144 shuts down after wake up from hibernation mode

Sometimes when I resume my computer from hibernation, I come back to it (after going to make a cup of tea whilst it boots up, for instance) to find it off again.
I have since observed it more closely and discovered the following: if I resume from hibernation and do not touch the mouse or keyboard, the computer will load up Windows but then hibernate itself again immediately.
If I move the mouse pointer at some point whilst Windows is finishing loading the desktop, etc., then the computer doesn't automatically hibernate.
Has anyone else had this problem and is there a solution?

Thanks for your reply. I am, and always have been, running the latest BIOS. I have never experienced the issue with standby, but that is probably because of the way I use my computer -- with standby, I start using it immediately. I have not tested resuming from standby and not pressing any buttons or moving the mouse.
Have you tested it as I described, by not moving the mouse or pressing any keys when resuming from hibernation, or are you just recalling from memory that you have not experienced it?

Similar Messages

Toshiba Satellite A300-20T shuts down after 5 seconds!!

my laptop satellite A300-20T shuts down after 5 seconds of booting , i dont know why ?? and i searched for support in the website and didn't find it in the model list, also i don't know why ???!!
i want to know why it shuts down , and how can i communicate with support

Yours would not appear to be a US model. We need the Part Number for your laptop, like PSAG8U-05K02C. You can find this on the Toshiba label on the bottom of your laptop. As well, what country was it originally purchased in. In addition, what is your operating system version, like Windows Vista 32bit?
Mike

Satellite Pro U200 shuts down after 5 mins then starts after a while

Satellite Pro U200 shuts down after 5 mins then starts after a while. When it shuts down the
blue screen says - stop: (0x0000008e,0xaa846f58,0xa9f29808,0x00000000)
sysaudio.sys - adress aa846f58 base at aa843000, datestamp 41107f1a

Hi
Believe me; its not easy to say exactly why the BSOD appears.
Generally it happens because of the serious software malfunction or hardware fault.
Did you use the OS from the Toshiba image?
There message says something about sysaudio.sys.
This file is a system audio WDM filter process and its a part of Windows OS. It controls the hardware like printer or graphic card on a lower level.
Note: The virus uses such files as a camouflage. You should use always a anti virus application.
Furthermore you have suggested that the notebook shuts down after 5 min.
Well, this sounds like a overheating issue. How did you use the notebook? You should know that the free space around the notebook is very important because of the air circulation. The ventilators should be also free.
I you use the notebook in the right position and this will happen again so I would recommend asking the Toshiba service partner for the help. They should check the notebook.

After update to OS X 10.7.5 on my Mac Pro (2009) USB ports don't work at all after wake up from sleep mode; with 10.7.4 there was (nearly) any problem.

hello,
after update to OS X 10.7.5 on my Mac Pro (2009) USB ports don't work at all after wake up from sleep mode; with 10.7.4 there was (nearly) any problem.
the used ports appear to be "killed"; the unused USB ports seem to work, but the Mac works in slow-motion.
The only "solution" is to restart my Mac.
- SMC-reset, PRAM-reset or repairing user rights had no positive effect; what is the solution - a bug-fix-update???

I have a mac mini (A1283) with OS 10.7.4. Upon upgrading to 10.7.5 it did not start up again. Instead, the light was on and the hard drive did not start up. The light on the connected USB mouse was not lit.
My solution:
Cold start with Command-v pressed.
This should start Verbose mode (see http://support.apple.com/kb/HT1492 ).
What happened on my mac mini was that the grey startup screen with the Apple logo appeared for a long while before the login screen came.
Maybe Cmd-v set open firmware params and fixed some corruption.
Anyway: my mac mini works again.

T400 bluetooth doesn't turn on after wake-up from standby mode

Hello
Please help
My T400 doesn't turn on bluetooth after wake-up from standby mode
i need to enable it every time by hand.
Thing thing appeared after migration to Windows 7. Before, i used WinXp and that worked fine.
I setup all recommended software via SystemUpdate

On T400s this happend, if you try Linux to install and after that you install Windows 7. I have test Ubuntu (boot from LiveCD) and after that i had exactly sam eproblem. Solution was to reset BIOS to default values.
Lenovo T440s, 20AQ0067MC, Windows 8.1 Pro x64 UEFI, Samsung 840 EVO SSD 250 GB, 8 GB RAM
Lenovo T430s, 2356LQG, Windows 8.1 Pro x64 UEFI, Intel 520 SSD 180 GB, 8 GB RAM
Lenovo T420s, 4171-6SG, Windows 8 Pro x64 UEFI, Intel 320 SSD 120 GB, 8 GB RAM
Lenovo T400s, 2808-CYG, Windows 7 Ultimate x64

Satellite P200-143 shut down issues

When I shut down my computer, while on the mains, the computer shuts down normally but a minute later, automatically restarts.
However, on battery it shuts down as it should.
I've checked my power settings, and they are all fine.
So I was wondering if anyone knew what I could do.
I have been shutting down by keeping the power button pressed, as it seems to be the only way.

I have a problem with my Satellite P200-144. Every time I plug it into the mains, it lasts about twenty minutes, and then cuts out. The time period is always the same, and it only ever happens when plugged into the mains, it will quite happily run on the battery until it runs dry.

Satellite A30-921 shuts down after 10 mins

I own a Satellite A30-921 but it shuts down after 10 mins.
I've tried to alter the toshiba power management settings but they wont work any ideas ?

Does the notebook shut down automatically without showing any error messages?
This could be caused by an overheating issue!
How old is your notebook and did you clean the cooling ventilators in the past?
If not I would recommend doing this.
To clean the ventilators you could use the compressed air spray which can be purchased in most computer stores.
The problem is that the dust and debris inside the notebook prevents the cooling modules from properly working and therefore the temperature increases to the higher level. This leads to the automatically shuts downs.
In my opinion the fans cleaning could helps to solve this issue.
Bye

Equium A110: Cannot use LAN after wake up from hibernation or standby

Hi guys
I cannot use lan on my tosiba equium A110 after it wake up from hibernation or standby. The lan icon is there bur internet wont work. Please help me out.
One other problem. when i try to cut some thing i cannot paste it if i open a new folder. I have to keep the folder open go back cut it again and then paste it. I mean if after cut i open any folder it wont paste it.
Please help me out .
Thanks

Hi
Did you try to refresh the connection? Something similar happens on my notebook but not with LAN but with WLan. If you right click on the small lan icon you will see the option repair. Check it.
Have found also this possibility. I dont know if it will help but try it.
1. go to [Start] -> [Control Panel] -> select [System]
2. On system properties dialog box select [Hardware] tab -> click [Device manager]
3. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
4. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
5. Press [OK] to close the dialog box.

Satellite P10-554 shuts down after few minutes and I can not reboot

hello,
i hope anybody can help me with my satellite P10-554
when i start the notebook everything works fine a few minutes. than the monitor turns into black and the notebooks shuts down suddenly. i cannot reboot it, when i push the start-button nothing happens.
i have to wait for about an hour and then i can start it up again, but he works just a minute and shuts down again !
help me please, cause i need my notebook to work !

I did that many times. First you need a special torx-screwdriver. Then you can remove the cover over the fans. Than take your vacuum-cleaner and remove the dust. Take a brush or somethin else to remove the dust from the fans. Then, you need to remove I think 2 big screws, now you should hold the cooling falance in your hands, the one with the fans. Clean that properly.
After that you can remove the copper-cooler, with 2 more screws I think, but it is pretty obviously. Now you should see the blank cpu with lots of heat-paste on it. I dont know why they put so much of this stuff on it from toshiba. So get a better one like Arctic-Silver or sth. My advice is to take the CPU off (one screw on top as far as I remember) and clean the surface.
The copper you can clean under water, but dont use sth that could scratch the surface. After that let it dry good. Now just put the CPU back and fix it with the screw again. Take a !litte! heat paste and put it properly with a paper all over the surface of the CPU, but remember, just a little! Then follow all steps back, dont forget to clean the graphics-chip as well and put some paste on it. You can see which it is when you look under the fan-cooling-falance, there should be a rest of heat-paste. Everything back to its place and voil*, a nice, cool clean notebook. By the way, I replaced even the fans.
If you need further advice, just ask!

Satellite Pro 6100 shuts down after 15-30 minutes

My satellite Pro 6100 cuts out after 15-30 mins operating on mains power. There is a snapping sound and all lights go out except slow flashing amber (power problem). I restore it by removing the power cable and waiting a while.
It will then boot up again. I have used two different power adaptors and two different battery packs. It also happens if running on mains with no battery in. My suspicion is an overheat cut-out. Does the Sat Pro have one? Might it be clogged with dust inside (it is 5 years old)? If so how do I clean it out. I don't think it is fan failure as I can hear the fan cut in. Advice much appreciated. Thank you.

Hi there,
Me and my partner, have the same LapTop, and I've located the problem in connector between PSU board and MainBoard. So, if you've never opened your LapTop, now is the time, but be prepared with tools for SMD soldering. Usually, the connector on MainBoard is the problem. The reason for this is that Toshiba made flaw in design of the housing and admitted that, which resulted with court order for replacing the LapTop with some models from newer line for that time, or paying cash amount ($1.000). I intend to repair my LapTop in a way that I will replace the connectors (both on PSU and Main Board) with thin wires. I know that this is a hell of a job (160 solder points) but what can I do, I love this machine. I am working on Compaq EVO N-610c, but he can only eat the dust from Toshiba.
Regards,
Alek
P.S. If you want to consult me about that matter, feel free to contact me on my e-Mail: [email protected]

Server 2012 X64 R2 DNS Server keeps shutting down after inplace upgrade from Server 2012 X64

Hi,
ever since upgrading from Server 2012 X64 to Server 2012 R2 X64 my dns server keeps shutting down every several minutes before having to do a restart. When viewing the event log this is all I see..
The DNS Server service terminated unexpectedly. It has done this 497 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
if I look in the Application Error Log, I will also find the following:
Faulting application name: dns.exe, version: 6.3.9600.17031, time stamp: 0x530871fb
Faulting module name: dns.exe, version: 6.3.9600.17031, time stamp: 0x530871fb
Exception code: 0xc0000005
Fault offset: 0x000000000010b0e0
Faulting process id: 0x1740
Faulting application start time: 0x01cf531b2e3a7f5e
Faulting application path: C:\Windows\system32\dns.exe
Faulting module path: C:\Windows\system32\dns.exe
Report Id: 90a4ab37-bf0e-11e3-9446-003048df3f03
Faulting package full name:
Faulting package-relative application ID:
I have tried removing and then reinstalling the DNS Server role, but the same situation occurs..
thanks,

Hi,
I'm going crazy, I've upgraded my Server 2012 Standard to Server 2012 R2 Standard and now my DNS server keeps crashing since the in place upgrade. I have finally narrowed it down to it only crashes after several minutes if I load the data from
a file instead of the registry. As a test I:
-1- killed all my dns data,
-2- uninstalled the dns server role
-3- deleted the /windows/system32/dns directory
-4- reinstalled the DNS server role
-5- used the wizard to create a DNS server and a forward zone.
everything works okay, no crashes, then I change the advanced propertied of the DNS server to load from file, restart the DNS server and once again it crashes every 2 minutes..
Please help, this is killing me..
thanks in advance..

My computer shuts down after 45 seconds from when I push the power button. Anyone have an idea why?

After pushing and holding the power button on my Mac the apple screen comes on and after a few seconds there is a loading bar that tries to load something for a few seconds then it shuts down. I would say it is approximately 45-50 seconds after pushing the power button. Power comes on then shuts right off. This all originated when I tries to log in as a different user. It froze for a while, then I shut down the computer with the power button. Because I couldn't so it from the apple icon on the desk top

Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive & clear caches.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.

Shuts down after coming out of sleep mode

When my imac comes out of sleep mode it keeps shutting down and does a restart.

On restart, are you getting any error messages?
I would test this issue in safe mode and then reset the smc as well
Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support
OS X: What is Safe Boot, Safe Mode? - Apple Support

ENTOURAGE shuts down after downloading images from e-mails

I can download images from all of my web-based e-mails, including our web-based exchange. However, when I try to download images directly from Entourage, my hard disk slows down and makes intermittent thinking sounds until it finally downloads the image and then Entourage shuts down. I've reported this to Mac 1/2 dozen times and have had no response. Has anyone had similar problems? Thanks.

From the noises you describe, I'd be far more worried about the condition of the hard drive. Back up any important personal data immediately. I think the relation to Entourage is only circumstantial. The hard drive is the real problem.

DHCP loses ip address after wake up from sleep mode.

My wife and I got a WRT54G router to replace the ethernet hub we had been using in order to get better reception for our voip phone system. We connect to the web using a 2-Wire DSL modem which connects to the router. From there we use ethernet to connect our computers to the router. I am running a G4 iMac flatscreen and she just got a new Macbook Pro. I had a very difficult time configuring my computer for the router, calling Kalcutta numerous times, but finally got on the web. However, after I or my wife wake up our computers from the sleep mode, we find the infamous 169 xxx xxx xx ip address indicating that we cannot connect to the web unless we shut down the modem and the router and then restart them. This is getting to be a pain. Anyone out there got a clue?

rob4250 wrote:
after I or my wife wake up our computers from the sleep mode, we find the infamous 169 xxx xxx xx ip address indicating that we cannot connect to the web unless we shut down the modem and the router and then restart them.
Although, you do not state specifically, when shutting down the modem and the router, are you also unplugging them from the AC power, shutting down the computers and waiting at least 60 seconds? Then you restart in the order of modem, router and then computer waiting for each to fully sync up before turning on the next device, yes?
I had the 169 problem with another brand router and solved it by resetting the router to factory defaults, then re-setup for my use. See the Linksys DSL Setup for Mac and specifically the Note in Step 6.
HTH

Satellite P200-144 shuts down after wake up from hibernation mode

Similar Messages

Maybe you are looking for