Satellite P200-1BY - Wi-Fi turns off after reboot

Hello,
On Satellite P200-1BY, on reboot, the wi-fi turns off on reboot. The switch then is useless.
I don't know where does this come from, and another reboot set the thing right.

Can you enable it again with FN+F8?

Similar Messages

  • Satellite L555-10N display wont turn off after 10min on non-usage

    Hi,
    I've recently acquired a Satellite L555-10N notebook, which until now turned out to be a good choice.
    I have a little problem, though:
    In my Energy preferences, I set the time at which the display should turn off to 10 minutes, if the notebook is not in use.
    Although this worked fine for the last days and weeks, the display now won't shut down at all.
    I have not made any changes to drivers or BIOS or whatsoever.
    I remember changing some preferences at the ecoUtility-Setup to enable it.
    At that point, I got a message that some preferences would have to be changed in order to enable the feature and I agreed.
    I could not notice any changes that were made, but from that point on, the display wont turn off any more.
    I would very much appreciate your help!
    Thanks!

    Hi
    Which OS you are using?
    For Vista and Windows 7 I have founded a good article about the settings in Windows Power Management:
    http://aps2.toshiba-tro.de/kb0/HTD84026Q0000R01.htm
    Furthermore you can change the settings for every profile. That means you have to choose the Turn off the display function for this power profile that you use or every profile if I use all of them.
    Check this!!!

  • Can not turn on the monitor on Satellite after dispaly turns off after 10min

    hi..
    I have a problem with my laptop..
    when the display turns off after 10 minutes , it doesn't turn on again !!
    i move the mouse, trying to type on the keyboard, but it doesn't work..
    to turn the display on again i should close the lid to hibernate and open it again!!
    i hope that you will help me @_@ !

    Hello
    Check please http://support.microsoft.com/kb/917332/en-us
    To correct the behavior please download and apply the patch (KB917332) which could be found in the detailed resolution below. I hope it will help.

  • Yoga display turns off after 1 minute

    I'm having an annoying problem with my new Yoga related to the display and have not seen any other posts with a similar complaint so perhaps this is a simple fix that I'm just not able to sort out on my own. My display turns off after 1 minute of inactivity. The only means for changing behavior like this that I am aware of is through the Control Panel Power Options. My settings for "turn off the display" are 10 minutes on battery and Never while plugged in (note screen shot attached). Regardless of my settings, the screen turns off after 1 minute. I've changed the settings to multiple configurations and restarted with no change in behavior. Perhaps there's some other settings area, maybe something specific to Lenovo that I'm not aware of (since this is my first Lenovo laptop). Anyone with similar problems or insight?

    This may be a Windows 8 issue. I finally fixed this problem by identifying the screen saver as the issue (and I wasn't using a screen saver). Type "lock the computer" into the search box after clicking the search charm, which brings up the screen saver dialog box. Mine was set to 1 minute, though I'd never set it myself. If you can't change it, choose a screen saver and you should be able to do so (and can then switch back to no screen saver). BUT, here's the problem. Other things you install (or settings within things you install) can apparently change and override whatever you type in for the delay time. Try applying your new time and exiting from the dialog box, then open it back up again. I was finding that it kept going back to 1 minute. To reset things so that you can get control again, type "user accounts" into the search box and when the dialog box comes up, choose "Reset Security Policies". Then you can go back to the screen saver dialog and successfully change the delay time. See http://social.technet.microsoft.com/Forums/windows/en-us/ace4085a-b0ba-4a98-898d-cd92d9e88e13/window... for some detail.

  • My screen darkens after 1 minute and turns off after 3.  All of a sudden, now, after the screen shuts down, it comes right back on????

    My screen darkens after 1 minute and then turn off after 3 minutes (energy saver).  Now, all of a sudden, after it shuts down it comes right on???

    thank you so much sir... i am very thank ful to u... it was an breath taking moment ... i was almost dead as it didnt work

  • Screen turns off after a few minutes and needs to be closed then opened

    hi, as the title suggests my powerbook screen turns off after a few minutes before my screensaver is set to come on and when i come back and press a key or move the pad it wont start up so i need to close the powerbook then open it up again for it to activate. its not a huge problem but my programs which connect to the internet seem to lose their connection when i open it up again. is this normal? is there a setting i can change?
    thanks
    ross

    Is there a way to "disable" Standby, Suspend and Off just when watching movies (in fullscreen or not)? I want them to do what they usually do in all other cases.
    Setting them to 0 in xorg.conf does the thing, but I need that functionality only when I'm wathing movies. Making a script that alters adjustments in xorg.conf isn't the best solution - you'd have to restart X every time you want to watch a movie .
    Cheers,
    Daniel

  • For the iphone4, my light is on all the time! the light is supposed to turn off after a few seconds of use. how can i fix this?

    for the iphone4, my light is on all the time! the light is supposed to turn off after a few seconds of use. how can i fix this?

    If what Allen says does not fix the issue I have seen this as a Hardware issue and I would get into an Apple Store if it is close by
    http://concierge.apple.com/reservation/us/en/

  • MacBook turns off after the startup bong when trying to restart

    Greetings,
    When I try to restart my MacBook it turns off after the startup bong.
    Thanks

    Have you tried resetting the System Management Controller? That is a good first step for power related issues such as this.
    Best of luck.

  • TS1363 apple sign shows up and then turns off after a few seconds, and i can not connect to my itunes

    apple sign shows up and then turns off after a few seconds, and i can not connect to my itunes

    I have the exact same problem trying to use the Remote app on both my iPhone 3gs and iPad 2 with either my Mac or ATV2.  My Remote app used to work on my phone - I can't recall if I ever actually used it with my iPad, but when I tried today, I got all the same results as you did (on both iPad, and then iPhone).  I  was using my ATV2 to play music from iTunes on my Mac and wanted to use the Remote app, but it would not connect to either device no matter what I did. 

  • My ipod shuffle turns off after exactly 30 seconds of play. Already had a similar problem?

    My ipod shuffle turns off after exactly 30 seconds of play. Already had a similar problem?

    Did you see my post above?
    Have you tried a different set up earbuds to see if that helps?
    What about resetting the Shuffle?
    Resetting iPod shuffle
    B-rock

  • HT1430 my iphone 4 turn off after appearing message "temprature high, need to be cool down after than doesn't becoming turn on"

    my iphone 4 turn off after appearing message 'temprature high, need to be cool down' after that does not getting turn on by anyhow.

    Hello vijaypatel,
    Thanks for the question. The following article outlines the temperature warning that you experienced:
    iPhone, iPad, and iPod touch (4th generation): Keeping device within acceptable operating temperatures
    http://support.apple.com/kb/HT2101
    If the iPhone is no longer powering on, we will need to isolate this issue to determine if it is hardware related.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    - Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    - Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion.
    Learn about LCIs and corrosion.
    - Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    - After at least 15 minutes, if:
                   - The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
                   - The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
                   - Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    - If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
                   - If the display turns on, go to step 4.
                   - If the display remains black, go to next step.
    - Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to
    restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    - If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks,
    Matt M.

  • Iphone turns off after a few mn of utilization with the battery full

    My iphone 3GS turns off after the battery is fully regenerated. I can only use it a few minutes before it turns off. I have to plug it again to turn it on, and the indicator of charge is around 98 %. The problem does not come from the battery. Has anybody found the same dis-functioning? A solution? Thanks!

    More than likely the iPhone has a hardware problem.
    If there is an Apple store nearby, make an appointment to have this confirmed.

  • 10.6: Internet Sharing turns off after restart

    I use Internet Sharing on my iMac to share the Ethernet connection from my computer wirelessly to my iPod touch. In Leopard, Internet Sharing would turn off after a restart. Snow Leopard fixed the problem for a while, but now it's acting up again. Any help?

    Using MacOS X 10.6.2 I have the same problem.
    My network configuration is just the other way around (wireless Internet and Ethernet LAN).
    Looking this up in Google first, I came across this older support link of Mac OS X 10.2:
    http://support.apple.com/kb/TA21168?viewlocale=en_US
    The solution provided there is not really helping though.
    However, it appears that this is a recurring issue Apple is struggling already longer with. Hope they straighten that out at one point.

  • HT4061 Iphone suddenly turned off after it was working fine. How can I turn it on again?

    Iphone suddenly turned off after it was working fine. How can I turn it on again?

    Hi Bobgriff43,
    If your iPhone will not turn on, you may find the following article helpful:
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/ts3281
    Regards,
    - Brenden

  • Yoga 13 display does not Turn off after idle

    I have the computer set to the balanced power option, and the disaplay is set to turn off after 5 minutes on battery and 10 minutes when plugged in. Unfortunately the screen never turns off.
    Anyone know how to fix this problem ?

    hi tmpst,
    Welcome to the Lenovo Forums.
    If a wireless device (mouse, keyboard, etc.) is plugged to the computer, the display, screen saver or sleep function might not work. If this is your case, try to:
    1. Remove your wireless device (might include a usb dongle)
    2. Apply the Moving mouse causes laptop to exit sleep mode fix
    If you have Power DVD installed, apply http://support.microsoft.com/kb/913405
    Let me know your findings.
    Cheers.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

Maybe you are looking for

  • Adding a certificate to my N900

    I've added a certificate that is required to get to my exchange server but it still will not connect; What's up?  I put the cert at the root (data) folder with no luck.  I also used the Nokia PC and put it under the domain folder and still no luck. 

  • My z10 does not sync to my outlook

    For many years I have supported  Blackberry but I am at the end.  This is the 3rd z10 I have had, the battery lasts 3 hours and it does not sync with my outlook.  Where do you get  Blackberry support  ?  No wonder why Blackberry is going to go away.

  • ViewerPreferences (e.g. HideWindowUI) in Adobe LiveCycle Designer

    Hi, When creating PDFs in Adobe Acrobat, you can set some ViewerPreferences: * HideWindowUI * HideMenubar * HideToolbar true These settings can be set via "Document Properties" => "Initial View" => "User Interface Options" However, when creating a fo

  • Scom monitoring non domain computers

    hello experts i have scom 2012 and want to monitor non domain computers (servers in dmz) i have created new template in ca server then create new certificates for dmz server and scom rms server. now i have connection between two servers but there is

  • How Multiple Video Cards Work?

    Let's say I buy a MacPro with 2 video cards and I name the outputs 1 through 4. I want outputs 3 and 4 to mirror output 2, but I don't want to have to run output 2 at the same resolution as outputs 3 and 4. Is this possible? From output 1 I want to o