Satellite Pro 460 won't start with new hard drive in

I recently got a Satellite Pro 460 but it had no hard drive in.
It starts great with no drive in but as soon as I put a brand new hard drive in it won't start.
I thought that it might be to new a hard drive so I took my old working drive out my old Toshiba Satellite and still it won't start.
Any one got any ideas why this is and what can i do about it

It sounds like 80GB is too large for that model, I really doubt the BIOS and Chipset can support more than 8GB HDD. 8GB may not even work.
Here is some information regarding different HDD modes and limitations: http://www.adminxp.com/hardware/index.php?aid=129
504MB - limitation where the system is limited by the compatibility with the values of the BIOS system and the ATA interface by help of using the CHS mode. This limitation is valid for older computers 286/386/486. (1024 cyl 16 heads x 63sectors/track x 512 = 528,482,304bytes - 504 MB). In many cases special programs will help (Disk Ontrack Manager - Seagate, Disk Wizard - WD). Some operating systems can have problems with this software support and can have higher requirements on your knowledge of the OS and used programs.
2GB - Limitation of the maximal value of the FAT16 file system partition for DOS and Windows 9x. Some older computers cannot address more than 4095 cylinders (4,095 x 16 x 63x 512 - 2,113,413,120 bytes)
4GB Limitation of Windows NT - Partition with the FAT16 system cannot be higher than 4GB - Fdisk cannot be used for creating, but the Disk manager is used (Disk management in Windows 2000)
8GB - Limitation of the BIOS system. For the support of larger capacities you need extended functions of the BIOS system. Limitations valid for the x86 computers and some motherboards with Pentium and Pentium II processors. Some other operating systems must know how to use the extended BIOS functions (Extended Interrupt 13). We can use Windows NT 4.0 as an example where you need an updated disk driver or the Service Pack. (OS - DOS 6.xx and lower, Windows 3.x and lower and some other older OS do not have the support of the Ext. Int13).
8 GB - Limitation of the FDISK program in the DOS 6.22 OS.
?? GB - Possible problem with disks larger than 67GB under Windows 9x... See article WD800
32GB - (65535 x 16 x 63 x 512 - 33,822,351,360 bytes) other limitation of the BIOS system.
68GB - Possible problem with disks larger than 67GB under Windows 9x... See article WD800
137GB - Limit for the ATA specifications (28-bit addressing for particular sectors - 268435455 sectors - 137,438,952,960 bytes)
2,2 TBytes - 32-bit addressing used by new operating systems (in Windows 98 by help of the FAT32 file system).
144 PetaBytes - a limit for new ATA specification using 48-bit addressing, in peparation. Maxtor, Microsoft, VIA, Compaq and other companies under name Big Drives participate the development. The standard should be implemented and authorized by the ANSI NCITS T13 Technical Committee organization (www.t13.org) in the prepared ATA/ATAPI-6 standard (see www.maxtor.com/bigdrive)

Similar Messages

  • MacBook Pro won't boot with new hard drive, but a different MacBook Pro will

    So here are the details. My friend and I both have 13-inch Mid 2010 MacBook Pro's. Same processor and specs since they were purchased at the same time, but originally had 250 GB hard drives. His hard drive failed and needed a new one. Put a 500 GB Seagate Momentus 5400.6 in his computer, and tried using a flash drive with "Install OS X Mavericks" on it to install Mavericks on his new hard drive. No matter what, it wouldn't install. I finally was able to install OS X 10.9.4 on it by connecting the new hard drive to my computer with a USB hard drive enclosure. I put the hard drive back inside his computer and it wouldn't boot (stuck on the gray screen with apple logo and a spinning wheel). I then attached to the hard drive to his computer externally with the USB enclosure, and then it booted and worked perfectly.
    So, it seemed like the problem was with something inside his computer, but then I switched our drives, and that doesn't seem to be the case anymore. I put my original hard drive into his computer, and his new hard drive into my computer, and they both booted and worked perfectly, so I have no idea why his computer will not boot with the new hard drive internally.
    To summarize, his computer boots with: 1) new hard drive connected externally (won't work if it's internal), and 2) my hard drive internally
    but my computer boots with: 1) new hard drive connected externally AND internally, and 2) my hard drive internally.
    Both hard drives have OS X 10.9.4 installed
    If anyone has any idea what's causing this and how to make his computer work with the new hard drive internally that would be greatly appreciated.

    So after switching the internal SATA cables from each computer, now we have
    His computer, with my SATA cable:
    1) Worked with every hard drive!
    My computer, with his SATA cable:
    1) Works with 1 TB Toshiba hard drive
    2) Works with 500 GB Seagate hard drive
    3) Works with my original hard drive
    4) Flashing folder with question mark with his old hard drive
    So it turns out you were right! Definitely had something to do with the SATA cables. But it's still strange that mine was able to boot with all the hard drives except the one that was originally in his. So it seems like it was some combination of his SATA cable and something else, since when his SATA cable was in his computer only 1 hard drive (my original) worked, and when it was in my computer, 3 hard drives worked. But at least its working, and I'm just gonna keep our SATA cables switched since that seems to work out fine

  • Mac Mini won't book with new hard drives???

    I have a late 2009 mac mini server running snow leopard server.  I recently purchased 2 new hard drives as the I believe one of the hard drives was failing.  I formatted the 2 drives and installed Mavericks OS X server on one.
    When I put the 2 drives into the mac mini, the system won't boot.  I just get the flashing folder.  If I keep the old (snow leopard) drive in the system and connect the mavericks server disk as an external (USB connected) drive, it will boot and runs just fine.
    Am I missing something??
    Here are somethings additional facts:
    When I have the snow leopard server drive in and it boots from that, it doesn't recognize either of the 2 new drives.  Wants to either eject or initialize.
    I realize that it can read the newer system.
    I have to boot with the option key so that I can pick which drive to boot from.
    Any thoughts would be helpful.  I'm not sure why it works one way and not the other.
    Thank you.

    Did you set the Partition Map Scheme to GUID Partition Table before Formatting the Drives Mac OS Extended (Journaled)...?
    You can check in a couple of places:
    Apple > About This Mac > More Info > Hardware > Serial-ATA
    Or in Disk Utility by highlighting the Drive and looking at the Drive info

  • Imac won't boot with new hard drive installed

    So I installed a new 1Tb caviar black in my PPC G5 Imac, but when I turn the computer on, I get no video, no startup chime, nothing. The power light does come on, and fans start running after a minute or so, but thats it. I can't boot from the install disc.
    The computer boots up as expected when I remove the drive(startup chime, grey screen, missing folder icon).
    Any suggestions to what the problem is? Any help would be greatly appreciated.
    -D

    wierd i have similar problem. I removed HDD after crash to backup in an enclosure before reinstalling os again, put the hdd back and connected the hdd sensor backup (although i thought it was a knock sensor..doh!) . Mac wouldnt start, no screen, no chime, nada, but sleep light stays on. With PCs this usually mean CPU fault so i removed RAM to see if could get a BEEP meaning CPU is ok as it spots ram. No beep. So after checking everything i stripped out ram, hdd, airport and battery and reset PMU, tried again and now i get beep!! so cpu works. slowly adding everything back in and trying power up, last thing to go in was hdd sensor and sure enough when this is connected i reproduce the symptoms. So i disconnected the sensor and tried and i get chimes etc... Ive inspected the cable and made sure is connected right way up and still cant get to work. So it seems sensor is goosed! Debating wether to replace just yet

  • I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you plea

    I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?

    You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
    Clean Install of Snow Leopard
    Be sure to make a backup first because the following procedure will erase
    the drive and everything on it.
         1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
             with your computer.  Insert the disc into the optical drive and restart the computer.
             After the chime press and hold down the  "C" key.  Release the key when you see
             a small spinning gear appear below the dark gray Apple logo.
         2. After the installer loads select your language and click on the Continue
             button. When the menu bar appears select Disk Utility from the Utilities menu.
             After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
             size.)  Click on the Partition tab in the DU main window.  Set the number of
             partitions to one (1) from the Partitions drop down menu, click on Options button
             and select GUID, click on OK, then set the format type to MacOS Extended
             (Journaled, if supported), then click on the Apply button.
         3. When the formatting has completed quit DU and return to the installer.  Proceed
             with the OS X installation and follow the directions included with the installer.
         4. When the installation has completed your computer will Restart into the Setup
             Assistant. After you finish Setup Assistant will complete the installation after which
             you will be running a fresh install of OS X.  You can now begin the update process
             by opening Software Update and installing all recommended updates to bring your
             installation current.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

  • Will Time Machine with Leopard Sync With New Hard Drive and Snow Leopard?

    My computer is a 20" iMac that I bought in late 2008. The hard drive had trouble so Apple repaired with disk utility. Week later, more trouble so they did full hard drive erase. Data was backed up on Time Machine, 500GB also bought in 2008. After full hard drive erase, and reinstall of basic software, upon reboot, computer would power on then immediately off. It doesn't get past white screen. They advised a new hard drive install is needed.
    A computer friend can install a hard drive just fine for me. However, I do not have the Leopard install disc. He could do it with Snow Leopard but I am scared. I'm afraid because my Time Machine last backup was with Leopard, not snow Leopard. I do not have my application discs with me, they are in storage in another state. Thus, if upon adding replacing hard drive and installing Snow Leopard my computer won't be able to sync FILES and APPLICATIONS from Time Machine because its on Leopard I will have a problem.
    How can I either 1)Get a Leopard install disc and do that with the new hard drive install OR 2)make sure that a Snow Leopard install with new hard drive won't prevent my Time Machine from being able to install the saved FILES and APPLICATIONS if I don't have original APPLICATION (ie Aperture, Photoshop) with me? Thanks for any help you can provide.

    thetrudz wrote:
    A computer friend can install a hard drive just fine for me. However, I do not have the Leopard install disc.
    Hi, and welcome to the forums.
    That Mac should have come with Leopard. If so, call AppleCare. They'll send you replacement discs for a nominal fee.
    Once this is sorted out, make a 8-10 GB partition on an external HD or your internal HD, and use the Restore tab of Disk Utility to copy the Install disc to that partition. Then you can boot and run from it instead of the physical disc. It will boot and run much faster, too.
    He could do it with Snow Leopard but I am scared.
    If he does, and doesn't provide a retail Snow Leopard disc, you must buy one ($29). It's a violation of the license to share software, and you'll need a SL disc to do things like restore a Snow Leopard backup, or the Snow Leopard Apple apps, or repair the internal HD.
    Your best bet is to stay with Leopard, at least until you have access to your 3rd-party software discs.
    What you can do, however, is borrow his Snow Leopard Install disc (assuming it's a white Retail disc, not a gray one that came with his Mac), and use it to do a full system restore from your backups. That's not a violation of the license, since you don't install or use OSX from that disc; you just use the Installer utility on it to restore the Leopard OSX and all your data from your backups.
    See #14 in [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum), for details.

  • I sent my 17inch mac pro to apple to install a new hard drive and my mountain lion was not on it when i got it back, using the same apple id i tried to re download it but it says i have to pay

    i sent my 17inch mac pro to apple to install a new hard drive and my mountain lion was not on it when i got it back, using the same apple id i tried to re download it but it says i have to pay

    never mind i got it by going into my account and veiwing hidden items and there it was

  • Mac Book Pro 15" mid 2009 after installing new hard drive and 8 gb memory, start up disk is still full, start up from power off is very slow, and programs open immediately after start up EX. word, excel.  Help?

    I installed a new 1tb WD hardrive in my mid 2009 macbook pro along with upgrading from 4gb to 8 gb.
    My start up disk is still almost full, booting up is extremely slow, and programs open up by themselves once booted up ex:word, excel.
    New TB drive shows up alng with 8 GB but, new hard drive not updating somehere?  What am I missing?  See screenshots below

    Thanks for the response, but I'm looking for answers to a few of the other answers before I look at completeing the steps above.
    1.  Whyis the new TB drive recognized in image 1 but still have the original 256GB size still recognized(and almost full) in image 1 also?  The HD should now be 1 TB, not 256 correct?  If this were the case, the HD, would only be fraction of full capacity,  Where is the disconnect between reconizing the installed tb HD but, it not being used?
    2.Image Number 2 shows once again that the new tb internal HD is recognized.  However, in image 3, the HD 256GB drive is still shown underneath the new HD.  Does this show that I am misssing something, some step, related to confirming the new HD should be fully reconized instaed of this old 256 that still remains?
    3.  In image 4, the SATA heading, shows the TB hardrive,  However, in image 5, the 256GB drive is still being shown under the storage heading?  Once again, seems like I've missed some simple step to make this all the same?
    4.Why is the start up from boot up soooo slow now.  I was never even close to this slow(slower than PC startup slow) before the new HD was installed.  IS this common when updraging to a new HD?  Doesn't seem right?
    5.  Why now all of a sudden when the computer finally boots up are certain programs automatically opening up, word, excel, when they have never opened up like this before?
    Summary:  1. New memory issues, 2. Very slow start up, 3.  Programs opening up automatically at startup.
    Until I address these issues, I'm not going to worry about loking through and deleting heavy folders.
    All responses welcomed!

  • Received macbook pro with new hard drive

    I just got back my laptop today from a shop i had a warranty at and they installed a new hard drive and also a hard drive cable.
    They gave me my old hard drive in a plastic bag and i was wondering if there was still anyway for me to get the stuff off of it because my latest backup was all the way in january which *****.
    not sure if my old hard drive is suppose to have a cable connected because it doesnt. The problem with my macbook was i kept getting a white screen with a circle and dash going through it, during start up.
    Is there anything i can buy to try and see if i can get the files off or what?
    im not sure if the hard drive still works or what because they didnt tell me anything

    Or something like this:
    http://www.walmart.com/ip/40900062?wmlspartner=wlpa&adid=22222222227028516939&wl 0=&wl1=g&wl2=c&wl3=61188529929&wl4=&wl5=…
    very cheap and versatile.

  • IPad won't sync with old iMac with new hard drive.

    The new drive recognizes the iMac, and the photos on the iPad were successfully imported into iPhoto, but 2 home videos on the iMac will not transfer. I have tried to manually drag and drop, different cords and ports, over wi-fi, etc... The Summary box says the iPad has never backed up to this computer, but when I try to do that, it tries and then stops with no error message. The Movies tab has the two videos I want to transfer, but the sync button is gray. I have hard rebooted the iPad and restarted the iMac. Also deauthorized and reauthorized the iMac. I suspect that somehow the iPad is not recognizing the new hard drive. Is that possible? Any suggestions? Thank you for your help!

    I don't mean the latest version of iOS.  I mean the latest version of iTunes on your Mac.
    Open iTunes on your Mac.  Click Help and then Check For Updates

  • Can't recover software to Satellite L745-S4210 with new hard drive

    Was using the laptop when it completely froze. Used power button to force shutdown. When restarted, hard drive was making a ticking noise and got this error message:
    PXE-MOF: Exiting PXE ROM
    No bootable device - insert boot disk and press any key.
    Setup utility did not show the presence of a hard disk drive. Assumed that hard drive had gone back.
    Purchased a new hard disk drive at MicroCenter. Toshiba 2.5-inch SATA 640GB drive, the same drive that came in the laptop from the factory. Also used the opportunity to upgrade RAM from 4MB to 8MB.
    Installed new hard disk drive and new memory. Ordered the Recovery Disk set from Toshiba.
    At startup, new hard drive doesn't tick. Setup utility sees a Toshiba hard disk drive. Got the "no bootable device" message. Inserted the first disk of the Recovery package and held down the C key, per instructions. System began to respond but then switched to Windows Boot Manager screen.
    Here are the error messages:
    File: \Boot\BCD
    Status: 0xc00000e9
    Info: An unexpected I/O error has occurred
    Reseated both new hard drive and new RAM. Tried again with same result. Reinstalled old RAM. Tried again with same result.
    Now at a wall. What has gone wrong? Is the new hard disk bad? Bigger problem. The unit is outside the factory warranty.
    Any help is appreciated.

    File: \Boot\BCD
    Status: 0xc00000e9
    Info: An unexpected I/O error has occurred
    I don't understand how that could appear when you boot from a recovery disc with a new hard drive in place. It implies there is something on the drive.
       0xc00000e9 "Boot\BCD" "unexpected I/O error "
    Maybe try another drive?
    -Jerry

  • Wanting to upgrade Sawtooth 400 with new hard drive and more memory

    Have been reading a lot of posts today on the above upgrades. Am quickly getting confused on all of the info, especially on the hard drive upgrades...
    Purchased my Sawtooth back in Dec. 2006 on eBay. Should have been using it all of this time, but my budget wouldn't allow me to put more memory (it's got 256MB now) and a new hard drive in it. Tired of seeing it in the way just sitting there!
    The G4 has OS X 10.3 on it. Would like to upgrade to Tiger. Is there a firmware update that needs to be done before upgrading to Tiger? I know that 256MB of memory really isn't enough for Tiger. I thought about getting at least a 512MB stick to make the total memory 768MB (wish I could afford to max the memory). Others have said that OWC and Crucial have good quality memory.
    The System Profile shows that it has 10 GB and 60GB hard drives. Imagine the 10GB one is the original. The 60GB was probably added on later. Don't know how old the 60GB is. That's one reason I'd like to replace it to at least a 120GB drive, so I can start fresh without worrying about the 60GB dying. (Do understand that any drive can die; new or old...) Have read about the 128GB size limit on my G4. Don't think I'd use most of the 120GB, so I'd like to stay with that size. Budget won't allow to install a PCI card to allow larger drives anyway. Should I remove the 10GB one as I don't think I'd be using it at all?
    I installed a Seagate 120GB Barracuda Ultra ATA/100, 7200RPM, 8MB Cache, 3.5" drive (new, got it on eBay for $40!) in my iMac G3 400. Would like to find the same kind of drive for the G4, if it would work. If the same drive would work in the G4, does anyone know where I could purchase one? Will look on eBay etc. in the meantime.
    Thanks for any advice and/or suggestions.

    Got the Seagate HD installed, PRAM battery replaced and missing PCI cover replaced. Sure wished that I had the extra memory to install now, but I haven't had the chance to order it yet. I know it's easy to do, but I'm going to have to move the Mac to the table and it's heavy for me to lift (bad back).
    Anyway, I started to install OS 9 on the Seagate and have hit a stumbling block! Didn't have this problem when I replaced the HD in my iMac, but it was only a 120GB drive (it needed the firmware updated).
    I've looked at other posts on installing OS 9 and even on Apple's support documents and can't find what I exactly need to do! Am getting more confused about it the more I try to find the right answers... Hope one of you can help me some more.
    I was able to boot the Mac up from the CD (it's the white one with the orange "9" on it). I clicked on the "Mac OS Install" icon, click on "Continue" (on the "Install Mac OS 9) dialog box, and then it says: A valid destination volume can't be found. To continue the installation process, mount a valid volume for software installation." The destination disk options is grayed out. I then clicked on the "Utilities" icon, and then the "Drive Setup" icon. It shows a list of drives and I clicked on the <not initialized> Type ATA, Bus 2, ID 0, LUN 0 and clicked on the "Initialize" button. Then it says: New Partitioning: 1 Mac OS, Initialization Options: None. If you click on Custome Setup, it says that the Partioning Scheme is "Current Volume," 131072MB (131GB?), under Volume Info Type it says Mac OS Standard. The "OK" button is grayed out. If you click on "1 Partition" on "Partitioning Scheme," then the Volume Info Type says "Mac OS Extended, with Size showing 131071MB. The "OK" button is not grayed out. I didn't go any farther with the OS 9 installation, as I don't know what the heck I'm doing! Don't want to mess something up. Do you or anyone who has helped me with this posting, know the steps I should take next? The Seagate Owner's Manual says if you have a system that can't read the entire 160GB, to just partition the drive for 137GB for now if you don't want to add a PCI controller card etc. For now, all I want to do is use the 128 or 131GB (according to what it says) of the 160GB drive without using a different card or software to recognize all of the 160GB. Do I just do one partition or two... and what else? I'm completely lost...
    Sorry for the long post, but had to write down the steps I took, so someone could tell me what to do next.
    I don't think you have to worry about PRAM settings; they pretty much take care of themselves - and regenerate when they have to. The time to think about PRAM is when you introduce new hardware and catch your Mac expecting same old, same old, and it isn't.
    It was kind of hard to get the old PRAM battery out of its holder. I pryed the right side retainer tab just a bit with a screwdriver to get it out. Noticed that one part of the retainer at the base was cracked! Hope I didn't do that! Put some super glue on the crack (was on the outside only from what I could see). Cleaned off the battery contacts with a pencil eraser and dry Q-tip before installing the new battery. It seems to stay in place even though with the side retainer cracked. If the side retainer would break off the next time the battery would need replacing, would the battery contacts hold it ok? Or would the whole logic board have to be replaced? I put a SAFT 3.6v LS14250 battery in it. The old one was a SAFT LS14250C. Hope the "C" at the end doesn't mean anything.

  • How to Replace existing Hard Drive with new Hard Drive, while keeping old files

    Hi All,
    I have recently replaced my hard drive on my Macbook Pro, with a new hard drive. The old Hard Drive was 160 GB, while the new one is 320 GB.
    What I did before replacing it was clone my hard drive using "SuperDuper". I cloned it to the new hard drive and then simply removed my old hard drive and installed the new one with the clone on it. Then I booted it up and began running it. In fact I am using it right now.
    My questions are:
    Is this a good practice?
    Will this work, without problems, indefinitely?
    Is this the prescribed way to upgrade ones laptop hard drive?
    The reason I did it this way was because I upgraded to Mountain Lion via the apple store download and I do not have the CD for the OS. So I figured if I could make a bootable copy, that might work. So far everything seems fine, but I really just want to know if this will last for a long time. I plan on also making a partition with Windows on it also, so I was wondering if anyone can comment on that too.
    If anyone can comment or give any advice on this topic I would really appreciate it.
    Thank you very much!
    Cheers.

    Every thing is fine except Super Duper does not clone the recovery partition.  If you start your MBP holding the OPTION key, you should see the internal HDD and the ML recovery partition.
    You can reinstall ML or reclone using Disk Utility>restore.
    Ciao,.

  • Canon Pixma 8120 won't print after new hard drive + TC install

    I have a great Pixma 8120 which was previously successfully networked wirelessly to an intel imac SL 10.6.8 and
    a Macbook Pro running Lion.  Our internet connection is Fios via router and the imac had been connected via
    ethernet to the Fios router. 
    Last week, the imac's hard drive needed to be replaced - Apple Geniuses
    installed the new hard drive at the apple store and restored all of the data.   I bought a new Time Capsule
    and backed up the new hard drive as soon as I got it home (yes I got religion). 
    I now have the TC connected via ethernet
    to the router and set up a new network -- connected both the imac and the macbook  via airport no problem.  Nice
    fast internet (safari). 
    The problem is the Canon printer.  I configured the printer to recognize the new network over the TC and was able to
    connect it via wi-fi to the access point.  When printing however, the printer icon pops up in the dock and looks like its starting
    to process the job but then the job disappears fromt the print queue screen.  poof.  nothing. 
    I  suspect I may have a problem with the TC's security settings not being compatible with the canon - the canon manual does say something about the canon not supporting "enterprise" and I did see that in the TC settings.   
    I have a huge work project due tomorrow so I decided to forego the wireless thing for now and just hook the printer up
    via USB to the imac.  I reinstalled the Canon software following the all directions for when to plug in the USB in the process. 
    It didn't work.  Then  I went to the Canon support page and downloaded/installed  an updated driver. Now I have
    a nice new looking printer icon but when I try to print it starts and then gives me a "communication error has occured"
    message -- error 306.
    Does anyone have advice for me? 

    Never mind.  I realized that I needed to ethernet the imac to the TC.
    I just got the Canon to print. Sorry to bother.

  • MacBook won't boot from new hard drive.

    I'm trying to upgrade my hard drive, but my macbook will not boot to the new hard drive. I have erased and cloned the hard drive about three times now, using both Carbon Copy Cloner and SuperDuper. It won't boot while it is in the macbook and it won't boot from an external hard drive case. All I get to is the screen with the mac logo and the spinning wheel. I have made sure the drive is GUID formatted, but it still doesn't work. When I put the new drive in an external case and plug it into the USB port of my macbook I can see and access everything on the drive. Can somebody please tell what I am doing wrong?
    By the way the new hard drive is a 500gb western digital Scorpio blue drive.

    I got a new hard drive recently 500gb seagate. I followed the directions on this page http://www.ehow.com/how2063795format-hard-drive-mac-os.html , Mine was a little more complicated since i had 2 partitions windows and mac on mine. Initially the process took a day and it started getting to the same thing as yours where it would get to the mac logo and not find the hard drive. I reformatted several times before i got to the point where i could boot up.Eventually I just figured out all the info was there the drive was formatted i could boot into windows 7 but not mac. So i put old hard drive back in the computer booted up with that. Attached new hard drive via usb in external case i was trying to put in the mac. I was able not to boot up but it would show the drives that have been formatted into the new drive and i simply copied my existing Disk by dragging it onto the new hard drive. Than turn off your mac keep your hard drive plugged in. Press and hold the option key in start up and you should see the 2 seperate hard drives and be able to boot into the new one. Was a long process for me took several complete deletes of the new hard drive and reformatting before it would work. once you get to the mac logo and spinning wheel its just saying mac cant find your boot up disk though. Sorry its confusing a bit any questions email me.

Maybe you are looking for