Satellite Pro A10 wont boot up

I really hope someone can help, my laptop just suddenly shut down. Since it has shut down i cant load the Laptop in any mode including safe mode. It gets to as far as the windows xp screen with the bar running along the bottom, but that is it.
in safe mode it will just load the drivers and then just do nothing
any help would be appreciated as its not even my laptop

Ive just tried the recovery disk and they dont seem to work
get the following message
GDISK (E) SECTOR 0 OF FIXED DISK 1 FAILED VERIFICATION - INT13
ERROR:CONTROLLER FAILURE (0X20)
GDISK (E) CANNOT WRITE TO SECTOR 0 OF FIXED DISK 1 - INT13
ERROR:CONTROLLER FAILURE (0X20)
GDISK (E) CANNOT REINITIALISE MASTER BOOT RECORD - INT 13
ERROR:CONTROLLER FAILURE (0X20)
TDSIKSZE V1.0 GET HDD SIZE
HDD SIZE = 30GB
GDISK (E) NO SUCH FIXED DISK - 1
Then it flicks to a blue screen like it is going to start an installation the a message comes up saying
!!!!!!!!!!!! ERROR !!!!!!!!!!!!!!!!!
EXTRACTION FAILED
Has anyone got any ideas :S i tried the simple option during recovery.
anyone help please

Similar Messages

Satellite Pro L40 wont boot after changing BIOS settings

Alright changed a few settings in the bios last night and now when I boot I get a black screen lights flash and that hard drive light comes on but nothing on screen.
There was no password on bios,... how would I reset BIOS to normal?
I put a windows disk on I can hear the disk spinning but nothing on the screen
(I think I have come to the right place on the forum)
Its a Toshiba Satellite Pro L40 model psl4be.
Thanks

>There was no password on bios,... how would I reset BIOS to normal?
You can set the BIOS to default ONLY inside the BIOS so you have to access the BIOS pressing F2 or at the beginning of the booting order
But I doubt that this problem is related to the BIOS.
Maybe its just a simple bad luck that this issue happened just exactly after changing something in BIOS.
Try to connect an external monitor and check if you can see something on 2nd display.

Satellite Pro L300 wont boot up after updating BIOS from 1.30 to 1.50

Dear All,
I own a Toshiba Satelklite Pro L300 and had no problems for the past 4 years. Last Monday I replaced my Hard Drive with a new one and after installing a fresh copy of Windows XP Pro, I downloaded all the drivers from the offical website. Upon finishing my last update, I updated the BIOS from version 1.30 to 1.50. After a few seconds my laptop restarted and was unable to load Windows and/ or recognise my new Hard Disk.
I tried several methods, being Safe Mode, Bios Optimun Defaults etc but was unsuccesful. IO could not even re-install Windows as the Hard Drive is not being recognised by the Laptop. I formatted the HD again via my desktop Pc but still have the same problem.
I am really worried and would appreciate immediate help!
Best Regards,
Engelbert

> I formatted the HD again via my desktop Pc but still have the same problem.
What happen exactly when you switch your notebook on?
Set BIOS to deult settings and try to install original recovery image that you got with your notebook. If everything works OK that means HDD upgrade was successful and there is no some serious hardware problem.
After this check you can try to install WXP again.
Please post some feedback.

Satellite Pro 2100 Wont boot up

Have used this laptop for many years without any problems that is until today. the laptop refuses to boot up.
DC in 15V Ok.
Power light green On.
Battery light green On.
Built-in HDD Off.
When I pressed the start button, thought I heard two short beeps.
Can anyone please help?
Kimberlin

Hi
Did you see something on the display?? Maybe an error message which says that no boot source was found or something likes that???
Several times ago my notebook was not able to boot up. I have simply disconnected the AC adaptor, I have removed the battery and I have waited about 20 min.
Then I have connected everything again and the notebook has booted up
I dont know if it will help you but you know trying is for free ;)
So, check it

Satellite Pro A10 won't boot (HDD seems to be missing)

Hello, I hope someone can give me some advice on this problem: I have a 2 year old Satellite Pro A10. Recently it won't boot at all and I notice that if i look at the directories in the C: drive using the command prompt it says 'file not found'. Can't start Windows at all, not even in Safe Mode.
Using the recovery disks doesn't help either I get messages like No such fixed Disk and 'Extraction Failed'.
does this mean I have:
1 A damaged hard disk
2. Faulty connections to the HDD? - if so how do I rectify this?
the system didn't crash before this happened, it failed to load up when I started it.
Would appreciate any help.
Thanks,
Scl

Jeffery and Ivan25 are correct in HDD malfunction. Try and remove and reattach the HDD and see if BIOS sees the HDD. If not you are going to need to order a replacement HDD. If BIOS does not even see the HDD then you wont even be able to install any Operating system, because there is logically nowhere to store the data being copied.
Take it to an Authorized service provider near you to have it checked out. Could also very well be the HDD Controller on the Motherboard has went bad and can not detect any HDD connected to the motherboard even if it is new and unused.

Satellite Pro A10 - IDE 1# Error on boot up

HI there, i have a Satellite pro A10 and all has been working fine for the last few years until now.
A few days ago i started getting an error reading cd's / dvd's invalid disc format yet the discs work fine on every other pc.
Today i am getting IDE#1 error on boot up... the laptop is still standard from when i got it off the shelf. thinking the drive may have died due to wear and tear i replaced the drive with a working drive and i still get the same error. I have removed the ODD altogether and its still coming up.
I have also updated the bios from usb floppy which was successful. and the best part of all this. the dvd rom that came with the laptop works fine in my other tosh a10!!!!!!
Anyone got any ideas. i don really want to replace the main board if i can help it. this is the only issue with the laptop.
thx in advance people.

Hello James
IDE 1# Error is typical when ODD is not accepted by the system. The reason for that can be defective drive or usage of non-compatible drives. The fact is that every drive can not be used with every notebook model because of different pin assignment.
In your case it is really strange that drive work on other A10 but not on this one. Because of that I presume there is maybe some problem with connectors. I am afraid there is not much to do. You can try to check them and see if they are clean and not oxidized.
Sorry but we can only speculate what the problem can be but, like you know, only intensive test can give you more answers.
Good luck and pleas let us know if you will find out what the problem is.

Satellite Pro A10 won't boot up - Where to get the disks

I have a Satellite Pro A10 which currently won't boot up Windows (XP) as it says
The following file is corrupt or damaged:
C:\Windows\System32\Config\System
The Tools & Utilities CD-Rom which came with my laptop has unfortunately been scratched and won't boot.
I have the two System Recovery Disks, which are fine.
My questions:
1. Is it possible to purchase a replacement Tools & Utilities CD-Rom?
2. If so, where from?
3. Is there a way of restoring my laptop without having to completely reinstall everything and lose all my files?
Thanks
Message was edited by: Stuart_2007

Regarding the point;
a) Usually it should be possible to order the Tools & Utilities CD-Rom but I ask why?
b) You can purchase the CD from the ASP in your country
c) The older recovery CD supports an expert mode. You can use this mode to choose the partition where the OS should be installed. In such case only this partition will be formatted.
But listen dude. You dont need to order the Tools & Utilities CD because on this CD you will find only the Toshiba drivers which can be downloaded from the Toshiba page too.

Satellite Pro A10 - no response - HDD input#0 Error

Pro A10 Out of warranty, student daughter reports laptop no longer working, previously hanging and finally no response from any other LEDs when DC input from charger is connected.
Cleaned out fan/heat sink, lots of fluff etc removed. No obvious signs of why the M'Board dead though. Confirmed with meter that DC present from charger into M'Board. Ordered replacement M'Board, FHZSY1, from ebay and fitted, taking all static precautions, though can't confirm they were done by the seller.
New Board now recognizes DC input and recharged the battery OK. Tried to power on the laptop but dreaded INPUT#0 Error. Concluded that HDD had also been damaged. New one (Toshiba Boxed) arrived 2 days later but gave same error when fitted. BIOS will not recognize HDD at all. Tried all posts about checking connections and definitely no jumpers fitted. Laptop will continue to boot from a System CD as far as it can so believe the new M'Board is OK
Are the HDD's from the Satellite Pro A10 different to those on the earlier Satellite A10?
Any other ideas on this INPUT #0 Error?
Thanks

Thanks for your post on this. You have probably spotted when I said input#0 error I meant to say IDE#0 error.
The replacement motherboard was a used one, rather than new. When I powered the laptop up firstly with this replacement board I needed to set the time from its default of 1 jan 2000, suggesting that though it was still connected to its cmos battery it had lost its charge. Is it possible that this may have affected the bios as well? The POST shows it running bios version 1.2 where other sites indicate a 1.3 version to be available.
I'm waiting for a usb 2.5" HDD disk case to arrive so I can check out the 'old' and new drives in another desktop to eliminate that doubt.
Thanks

IDE #1 Error on Satellite Pro A10

Hi, My Satellite Pro A10 laptop displays IDE #1 Error everytime I attempt to put it on. That message is all I get, although it is displayed for a short time- the laptop always comes back to that message, it attempts to load the screen just go's blanbk and then that message comes up everytime! I was wondering if anyone could explain what this means and how do i fix it?
thank you
david

Hi
This is very strange that this error message appears and you have not changed the drive.
Did you try to 'flash' the drive or to install any firmware or update the BIOS?
I ask it because I can't believe that this error message appears without any reasons.
Like Jack and Silas say, this error appears because of no compatibility of the drive.
The unit was delivered with compatible drive and should works. I assume the BIOS cannot recognize the drive at this time because it's dead.
In my opinion you have to replace the drive. (try to check it it's possibel to install/to boot Toshiba recovery CD)
Ps: Just for info: I have read in the net that sometimes it's possible to flash the drive with any illegal software to change the master/slave settings but this is not advisable. But I have never tried it.
I have also read in the forum that if this error message appears every time and it's not possible to use the drive and the BIOS cannot recognize this device so the connection of pin 45 and 47 could solve this issue sometimes.
Check this topics:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=5457&messageID=18649
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=7005&messageID=24482

Satellite C50-A634 wont boot from USB or DVD

My new toshiba Satellite C50-A634 wont boot from usb, or dvd ,
i have downloaded win 8.1 and burn image to dvd but i still get an error message "no bootable device......please restart system" .
Can some one plz help?

Hi
Does Satellite C50-A634 supports internal CD/DVD drive or did you try to boot from external optical disk drive?
You have to know that _Satellite C50 & Satellite C50D models *without* a built-in ODD_ are not able to boot from an external ODD due to a technical limitation.
Details here:
[Limitation of external boot media for Satellite, Satellite Pro C50 & C50D devices|http://aps2.toshiba-tro.de/kb0/TSB3B03JA0000R01.htm]
Only USB flash drives are supported as external boot devices!
It is necessary you can use a USB flash drive as recovery media on notebooks without a built-in ODD.

SD-C2612 IDE#1 Error after wrong firmware update - Satellite Pro A10

Hi
I've got a Toshiba Satellite Pro A10 which has been flashed with the wrong firmware (i dont know which one as i didnt do it).
I've tried flashing it with the correct firmware (1315) but get the message for the Primary Master and Slave as 'Not ATAPI Device' and 'Drive Not Connected'.
NB: On boot up, even with the DVD ROM removed, I still get the IDE#1 Error.
Would updating the bios to the latest version help or are there any options open to me to resolve this issue other than resorting to the pin 47 & 45 connection? Would this even solve it?
Thanks in advance for any advice you can give.
Best regards
Angus

> I've got a Toshiba Satellite Pro A10 which has been flashed with the wrong firmware (i dont know which one as i didnt do it).
Lol :D I dont wonder that you get the IDE#1 Error message.
As you said by yourself you have flashed the drive with the wrong firmware. This has damaged the drives master/slave/c-sel settings and therefore the BIOS doesnt recognize the CD/DVD drive. But I ask myself why someone flashes the drive with a wrong firmware ?:| It's always known that a wrong firmware can damage the CD/DVD drive... and mostly it's not necessary to update the firmware.
> Would updating the bios to the latest version help
The BISO update will not help you because youve got already right BIOS and its NOT a BIOS issue but the wrong and not compatible firmware is stored.
> or are there any options open to me to resolve this issue other than resorting to the pin 47 & 45 connection? Would this even solve it?
I dont know if this helps but I know that this is not advisable because this can damage the CD/DVD drives hardware
I would recommend contacting the ASP in your country maybe the guys could bring the CD/DVD drive back to life. Lets hope

Media test failure check cable - Satellite Pro A10

Hi there
i would be most gratefull if some one can help me.
I have just installed a western digital 120 gig hardrive on a toshiba Satellite Pro A10 laptop on XP. on first boot up it comes up with this media test failure check cable.
It takes a while to boot up into windows then the windows sound comes up around 10 seconds after the desktop loads up. any help on this?
Also the DVD rom drive does not read DVD's only CD's
DVD model is SD-R2412
And is there any way tke make windows load faster and should it have the sound max driver installed or the AC Realtek.
Can someone let me know ASAP thanks syclonus.

If you order the boot priority and boot first from HDD you will not get this error anymore.
So go the BIOS with ESC key and change it.
Have you tested different DVDs in the drive? I think it could be a hardware problem. I had for a long time a similar problem that my drive does write DVDs only CDs.
There are a lot of tips how to make Windows faster. I can give you same examples: Defragment your HDD, check how many programs are in the startup folder and msconfig. Disable or remove all programs that you dont need.
Furthermore you can disable all services that you dont need (run > services.msc). Be careful what you do but I always disable automatic updates, security center, Windows Time, Help and Support, Themes and so far.
Clean up the registry. For this I use always the tool CCleaner. A very good tool and its freeware.
And if you make Windows faster the start up sound comes maybe at the right time.
All drivers you can get on the Toshiba website. Its not necessary to install other or more sound drivers.
http://eu.computers.toshiba-europe.com

Memory Upgrade on Satellite Pro A10

Can anyone advise me as to the correct RAM type to upgrade my Satellite Pro A10. Its a standard 256mB at the minute and I'm thinking of slotting in an additional 512mB next to it - but am bemused by the array of memory types and nomenclatures - DDR - SODIMM etc !!!
Handy with the screw drivers but not so hot with the acronyms. Many thanks to you all out there who know the score!

Hi
I understand you very well and sometimes Im also a little bit confused because of the whole notations in the computer world.
The Sat Pro A10 supports 200-Pin PC2700 (333Mhz) DDR SODIMM modules and you can upgrade the memory on this notebook up to 1024MB (2 x 512MB)
You could check this memory module page:
http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=21046&ft=m&st=3

Satellite Pro A10: Extraction failure error occurs while recovering procedure

Im trying to run the recovery discs on my Satellite Pro A10 but after 20 second of trying to install recovery disc 1 screen gose black and message in corner says extraction failure.
Can you help me please?

Did you try to format and to delete whole partitions on the HDD before performing the installation from the recovery CD???
Something similar happened to me. I was not able to install the OS from the Recovery CD.
I have simply used the original Windows CD and have formatted the whole HDD.
After this procedure the Recovery CD installation has worked.

Disk replacement on Satellite Pro A10 (30GB)

Hello
I am after some guidance on which replacement disk to purchase for this Toshiba Satellite Pro A10 laptop, model PSA15E-03U7V-EN. It still has the original 30GB disk in it but it's been showing errors when checking the disk with the Windows XP tool (it's still useable though). I've made a complete backup to an external drive.
Thanks in advance
Themos Tsikas
HWinfo32 output follows:
General Information
Drive Controller: E-IDE (ATA-5)
Drive Channel: Primary, Master
Drive Model: TOSHIBA MK3021GAS
Drive Revision: GA124A
Drive Serial Number: 73J94628T
Drive Capacity: 28,615 MBytes (30 GB)
Drive Geometry
Number of Cylinders: 16383
Number of Heads: 16
Sectors Per Track: 63
Bytes Per Sector: Unknown
Bytes Per Track: Unknown
Number Of ECC Bytes: 46
Number of Sectors: 16514064
Total 32-bit LBA Sectors: 58605120
Cache Buffer Size: N/A
Controller Type: Not Specified
Transfer Modes
Sectors Per Interrupt: Total: 16, Active: 16
Max. PIO Transfer Mode: 4
Multiword DMA Mode: Total: 2, Active: -
Singleword DMA Mode: Total: 2, Active: -
Ultra-DMA Mode: Total: 5 (ATA-100), Active: 5 (ATA-100)
Max. Multiword DMA Transfer Rate: 16.7 MBytes/s
Max. PIO with IORDY Transfer Rate: 16.7 MBytes/s
Max. PIO w/o IORDY Transfer Rate: 16.7 MBytes/s
Transfer Width: 16-bit
Native Command Queuing: Not Supported
TRIM Command: Not Supported
Device flags
Fixed Drive: Present
Removable Drive: Not Present
Magnetic Storage: Present
LBA Mode: Supported
DMA Mode: Supported
IORDY: Supported
IORDY Disableable: Supported
Features
Write Cache: Present, Active
S.M.A.R.T. Feature: Present, Active
Security Feature: Present, Inactive
Removable Media Feature: Not Present, Disabled
Power Management: Present, Active
Advanced Power Management: Present, Active
Packet Interface: Not Present, Disabled
Look-Ahead Buffer: Present, Active
Host Protected Area: Present, Enabled
Power-Up In Standby: Not Suppported, Inactive
Automatic Acoustic Management: Not Suppported, Inactive
48-bit LBA: Not Suppported, Inactive
Self-Monitoring, Analysis and Reporting Technology
Raw Read Error Rate: 100/50, Worst: 100
Throughput Performance: 100/50, Worst: 100
Spin Up Time: 100/1, Worst: 100 (Data = 942)
Start/Stop Count: 100/Always OK, Worst: 100 (Data = 5072)
Reallocated Sector Count: 100/50, Worst: 100 (Data = 52)
Seek Error Rate: 100/50, Worst: 100
Seek Time Performance: 100/50, Worst: 100
Power-On Hours/Cycle Count: 69/Always OK, Worst: 69 (Data = 12677)
Spin Retry Count: 201/30, Worst: 100
Power Cycle Count: 100/Always OK, Worst: 100 (Data = 4823)
Power-Off Retract Count: 100/Always OK, Worst: 100 (Data = 126)
Load/Unload Cycle Count: 18/Always OK, Worst: 18 (Data = 824818)
Temperature 100/Always OK, Worst: 100 (Data = 43.0 C)
Reallocation Event Count: 100/Always OK, Worst: 100 (Data = 46)
Current Pending Sector Count: 100/Always OK, Worst: 100 (Data = 233)
Off-Line Uncorrectable Sector Count: 100/Always OK, Worst: 100
UltraDMA/SATA CRC Error Rate: 200/Always OK, Worst: 200
Disk Shift: 100/Always OK, Worst: 100 (Data = 118)
Loaded Hours: 82/Always OK, Worst: 82 (Data = 7578)
Load/Unload Retry Count: 100/Always OK, Worst: 100
Load Friction: 100/Always OK, Worst: 100
Load-In Time: 100/Always OK, Worst: 100 (Data = 389)
Head Flying Hours: 100/1, Worst: 100

Hey,
> 48-bit LBA: Not Suppported, Inactive
This would mean you can only use HDDs up to 128GB if 48bit LBA is not supported.
But if your current HDD has only 30GB I think something with 80GB should be enough or how much disk space you want?
The HDD brand is not important, every HDD is compatible so just buy new HDD with good offer. :)

Satellite Pro A10 wont boot up

Similar Messages

Maybe you are looking for