Satellite Pro A120: How to remove the CD/DVD drive

I have 2 main problems and can't seems to fully open case.
Does anyone know how to remove the dvd-rom?
But my mainproblem is the power swith ribbon (blue) has come loose from the motherboard. But as i can't fully open the case im using tweezers to try to recconect it.
Doesn't seem to want to go in.
Is there a clip on the motherboard connector or is it just push in? A photo or diagram would be useful.
Any help would be appreciated.
thanks

One question; why do you do this?
I mean why your want to open the notebook?
Fact is that the Pro A120 Satellite is not a old notebook and I presume the warranty is valid.
If you remove the notebook covers you will lose the warranty!!!
The CD/DVD removing is very easy.
Usually it is secured with one screw which can be found at the bottom of the unit. You have to remove it firstly and then it should be able to take off the ODD.

Similar Messages

  • Satellite Pro 4260: How to remove the DVD drive?

    I have a Satellite Pro 4260 and it appears that the DVD drive is broken and I want to replace it. I cannot figure out how to remove the old one.
    Does anyone know how? Is there a manual available showing how?
    Thanks

    Hi
    This notebook is not know to me but a checked some sites in the net and it seems that the top cover must be removed.
    Then lift up the CD-ROM/DVD-ROM drive to disconnect PJ700 on the CD-ROM/DVD board from PJ15 on the system board.
    Remove two screws securing the CD-ROM/DVD-ROM connector board.
    Separate the CD-ROM/DVD-ROM connector board and CD-ROM/DVD-ROM connector brace from the CD-ROM/DVD-ROM drive
    Well, I think its not easy for someone with no experience.
    Therefore if you dont know how to do it and you have no much experience you should ask someone how knows what to do ;)

  • How to make the CD/DVD drive compatible on Satellite 5000-204

    Hi all,
    I see a thread on replacing CD/DVD drive on this notebook, but it was closed, so i write this post.
    The most of recent unit is "cable select" type and will not be recognized from many Toshiba notebook.
    To solve that you must search a drive for which you can found a firmware update that change it to be "reverse cable select" type, as Nec or Optiarc
    If you buy a drive that can't be recognize (like me) read below.
    I succesfully replaced the DVD-ROM/CD-RW unit with a Pioneer DVR-KD08 DVD writer.
    This unit is a "cable select" type (as most other recent unit) so it can't be recognise by this notebook (and many other Toshiba models). The solution is to connect pin 45 and 47 together on the drive or on the connector adapter (this second solution is simpler).
    If you watch the drive from behind these pins are the second and third from the left on the upper row of pin of the connector.
    In the connector adapter it's simpler to connect these pin (with care) with a solder iron directly on the circuit board.
    Obviously on the circuit board the pins are the second and third from the right.
    After this the unit will recognize ok.

    Hi buddy
    First of all thank you for participation in the forum its always nice to have users who shares the own experience and knowledge.
    Thanks you also for this info how to make the CD/DVD drive compatible.
    But to be honest Im a little bit skeptical because there is a chance that the drive could be damage during this procedure.
    So everyone could do this but only at the own risk!!!
    Usually the compatible drives can be found in the user manual and it would be useful taking a look into the user manual before buying an NOT compatible drive ;)
    Cheers mate

  • Satellite Pro P300 - How to obtain the factory image without media?

    Hello
    I have been given a Satellite Pro P300 and it has the recovery disc for win xp, I would like to go back to the pre installed Vista intallation if possible.
    The recover partition on the hard drive isnt available so i assume it cant be recovered. Is it possible to purchase a factory image?

    Liam is right Win 7 is better than Vista OS.
    So if you have a possibility to install Win 7 I recommend doing this instead of Vista.
    However, the Toshiba recovery disk contain just Vista OS.

  • Satellite Pro 4290: How to solve the IDE #1 error issue

    I have recently aquired a DVD-ROM drive to upgrade my Sat Pro 4290 optical drive from a CD-ROM to DVD-ROM. As suspected I am having the problem that the drive is not recognised and get the IDE #1 error.
    I can get windows XP to recognise the drive by deleting the Secondary IDE Channel in the Hardware and then searching for new new hardware. It then installs the IDE Channel and then finds and installs the DVD-ROM and works fine. I reboot the laptop and back to square one!
    I understand it is something to do with the settings on the motherboard and somebody has resolved this by soldering pins to different places on theh IDE connectors.
    I do not want to risk this and was wondering if anybody found an easier way of doing this?
    Many Thanks

    Hi
    > I understand it is something to do with the settings on the motherboard and somebody has resolved this by soldering pins to different places on the IDE connectors.
    Thats not 100% true. This is not a setting issue on the motherboard but the setting of the CD/DVD drive.
    The drive supports different master\slave\c-sel settings and if they are not compatible the BIOS will not recognize the drive correctly.
    On the external drives (for desktop PC) its possible to change such settings by switching the jumper but this is not possible to the slim notebooks drives.
    The notebook drives settings are stored in the firmware!!
    I found different not legal tools which can change the master/slave/c-sel settings but I would not recommend using it.
    The risks are too high that the drive will be damage.
    So try to replace the drive with a compatible one

  • Satellite P10-804: How to remove the HDD?

    I'd like to remove the 60Gb internal hard drive from my satellite P10-804 and replace it with a bigger drive, but cannot figure out how to get inside the case to remove the HDD.
    Does anyone have details on how to do this?

    Hi
    In my knowledge the HDD must be placed under the optical dirve.
    To remove the HDD, first remove the battery pack and optical drive, then follow the steps below:
    1. Remove four black screws securing the aluminum shield covering the HDD and lift it out.
    2. Gently pull the HDD toward the computers front panel to disconnect it from the system board, then lift it out.
    3. Remove the four silver screws that secure the HDD case to the HDD.
    But be careful. If you have no experiences ask someone with more experience in such replacements.

  • Satellite Pro M40 - How to wipe the system to new

    I am having a lot of trouble with my Satellite Pro M40.
    When wanting to click in to the various files an error message comes up and asks me to send an error report. I think i may need to wipe the system to new. Does anyone know how to do this? I dont have the disks that I orgianlly got with the laptop to do this.
    Thanks :D

    As you know to open various files you need to use various software. So it will be interesting to know which kind of files you try to open. If you know exactly which software can not be started I recommend you to reinstall it in hope it will work again.
    Please think about it at first. If you still want to make clean operating system installation please write again. We will find a way to help you. ;)
    Bye

  • Satellite Pro M30 - how to recover the data?

    I get a disk read error when I try to boot my Sat Pro M30 running XP Pro, just after the In Touch with Toshiba screen.
    Using the Revovery DVD that came with the computer when purchased and entering advanced mode I'm trying to use check local Image File. It doesn't seem to find any Image file. Is it possible to recover or rebuild image file?
    There are some data I would like to recover from the HD so I'm trying to avoid reinstalling the system until I've recovered the files.
    Have tried to read from the HD using a cabinette and a new NP running Vista but it didn't work. Is there a general problem reading a XP HD from VISTA?
    Any suggestions how to recover the data would be very much appreciated!
    Johan

    cabinette ? Do you mean "USB Hard Disk Caddy" ?
    To recover your data, you can connect the HDD using a USB Adapter to another PC running XP or Vista. The drive should show up as a Drive letter (such as E: Drive), and you will be able to copy the files.
    When you say "but it didn't work", what was the problem exactly?

  • Satellite Pro L20: How to intsall the Office applications from recovery CD?

    I have just received my new laptop and I am supposed to have XP Pro when all is on my laptop is Microsoft Note.
    It does state that XP Pro is loaded but I cannot find outlook, word, p/point, excel etc all the applications that come with XPpro.
    Can anyone tell me how I load them on from my laptop? The only disk i received from Tosh is a recovery disk which does not have any mention of XP or XP pro only MS OneNote
    HELP would be greatly appreciated.
    Regards
    PT

    Hello
    The applications that you want to have are definitely not a part of WXP operating system. They are part of Microsoft OFFICE application package. It must be separately installed and it is not a part of Toshiba software.
    Please clarify this with your local dealer.
    Bye

  • How install the LAN driver for Satellite Pro A120

    Actually, my problem is that i didnt know how to install the lan driver on my Satellite Pro A120 to connect throug the net.
    The issue that theres no installation to do to complete the install.
    And theres other issue that i need the Ethernet Controller
    My laptop was vista OS installed, But i change it and put Windows XP instead
    Plz help me

    Thats very easy to install the LAN driver.
    On the Toshiba website you can search for it:
    http://eu.computers.toshiba-europe.com => Support & Downloads => Download drivers
    Select the right notebook. In your case its the Satellite Pro => Satellite Pro A Series => Satellite Pro A120.
    And then choose at operating system Windows XP and at Driver type LAN Driver.
    Click on search and you will get the right driver.
    Download and install it. How this works did Jimi said.

  • I got a new macbook pro and now I need to know how to remove the prior owners itunes id from my computer?

    I got a new macbook pro and now I need to know how to remove the prior owners itunes id from my computer?

    If you purchased a computer from another person, you need to wipe it clean.  To do this, click on the link - Erasing disks securely 
    Depending on your model Macbook Pro...
    Start up from your install disc, go to Disk Utility and select the disk and click erase - to securely erase data click Security Options and Erase Free Space which will entirely wipe your disk, overwriting it with zeros so that no data is recoverable.

  • Satellite Pro A120 - Cannot get the PCMCIA card to work

    OK i have a problem with my Satellite Pro A120's (xp service pack 2) cardbus.
    I use the cardbus slot to add firewire conections via a IEEE 1394 cardbus card and have been doing this a long time. The other night my comp went into hibernate with the card still in the slot and still in use and when i tried to use it the next day the card was not working at all.
    So i thought the had died on me and brought another one, this one to be exact [http://www.newegg.com/Product/Product.aspx?Item=N82E16839314003] .
    When i plug the new card into the slot windows starts the installation add new hardware thing but does not find the driver, there is none on the provided CD and it does not conect to windows update to find one ethier. So the new card does not work and does not get installed, it just shows up with ! next to pci device.
    I have looked everywhere on the internet to find the driver, read the manual etc.I even did a fresh install of windows so it might find the drivers but nope.
    The only thing i can think of is the slot does not except 32 bit cardbus but in my manual it says this:
    "The computer is equipted with a pc card slot that can accomedate a type II card. Any pc card that meets industry standards can be installed. The slot supports 16 bit pc cards, including pc cards 16 multifunction card and cardbus pc cards. Cardbus supports a new standard of 32 bit pc cards."
    Any help please
    Thanks

    Thanks for your help but i ahve already tried this including searching the net for the driver and no luck. I've also tried microsoft update but no luck.
    The reason i can't find the drivers is because the cardbus card is supposted to be plug and play but windows doesn't have them.
    The good news is i found out my old card was 32-bit just like the new one so my laptop is compatible. I don't want to just go and by another card incase that one won't work.

  • Does anyone know how to remove the fisheye effect from a gopro camera, remove it with premiere pro c

    Does anyone know how to remove the fisheye effect from a gopro camera, remove it with premiere pro cc.

    Use the Lens Distortion effect, set curvature to your liking.

  • Satellite Pro A120-145: yellow exlamation mark in the device manager

    Hi all,
    I have a Satellite Pro A120-145 running Win Xp Pro fully patched and up to date, I have a yellow exlamation mark against "serial" in non plug and play in device manager (when i click show hidden devices).
    Could anyone tell me which driver is needed for this? I don't want to use the recovery disc as I have done a custom install to get rid of excess baggage which is included on the disc.
    thanks in advance.

    That troubleshooting guide that Juan28 posted is really good. If the driver of the unknown device is already available (i.e. after the recovery CD installation) you might find your way through.
    In case you can't locate a suitable driver for your unknown device on your Laptop, you could try and download a freeware called "Unknown Device Identifier" from this site:
    http://www.zhangduo.com/udi.html
    This program will allow you to locate the device ID and make a search with it on the Internet.
    Hope this will sort things out.
    Regards
    electrochain

  • Re: Satellite Pro A120 - Cannot access the BIOS and install the Win XP

    Hello
    Ive a Toshiba Satellite Pro A120, Ive installed a Linux operating system on it, and uninstalled it.
    When I come back to the Windows XP OS, I could no more access the Bios (event the i press F1, F2 ) and the computer could not boot the windows XP SP2 CD too but it boots the windows XP 2001 CD
    Any one could help me please

    Thank u jeffrey for your help, ;;;;;or the BIOS i'll try later....for the boot, i tried many times,,,, i screen to shoose the boot appears, and when i select the cd boot it works with the windows xp 2001 SP1, but with windows SP2 it doesn't boot,,,, even though i tried many cds of win sp2 ,,,, so each time , to install windows sp2 , i have to install SP1 then upgrade to SP2 and it takes much more time... i precise that few months ago it was proprly working with the WIN XP SP2 CD
    best regards

Maybe you are looking for

  • Apple Tv will only work on 1 TV - How do I get it to work on an alternative TV

    My Apple TV works perfectly on one of my Televisions.  But when I unplug it and move it to a different room with a different Television it won't connect.  Apple Tv White Light is on; iMac can see Apple Tv is on, Wireless Network is Available, Correct

  • No of days elapsed for a given month

    Hello, I am trying to find number of days elased for a given month. How do I write this in CMOD. My input variable is CALMonth/Year  - 06/2010. If I run the report today, I should get numbers of days up to today. Please advise. thanks for your help i

  • Iphone 4 not showing up in iTunes in new computer

    Just got a new computer.....migrated all my stuff for my old macbook....everything works fine except when I try and sync my iphone 4......it doesn't show up in iTunes....iPhoto opens up and it did show there but not in iTunes... Any idea how I can fi

  • I have finally finished my lightbox

    I finally got my LB working in IE i had to sacrifice the fade in effect and give IE its own code for many things. anyway 2 problems remain perhaps someone ca give suggestions 1) in the corner of the faded area the corners dont quite line up with the

  • Missing "images" in Safari

    I use my Macbook Pro and Safari as my main computer. I also have a five year old Dell PC. I am pretty much doing everything on the MAC but every now and then I need to go back to the PC as a web page does not load correctly. For example: tonight I wa