Satellite Pro A200-16YT - Wireless adapter card upgrade to 802.11n

Satellite Pro is A200-16YT (PSAE1E) with Windows XP Professional SP3.
I have been trying to increase my existing 54 Mb/s wireless network speed by replacing the existing Atheros AR5007-EG 802.11a/b/g with the faster 802.11n adapter.
The Atheros driver is v9.2.0.439 (04/08/2011) which I believe is the latest. I have tried to install an Azurewave AR5BXB72 (Atheros AR5008) as a replacement, but with no success. As well as trying the standard Windows Wireless set-up, I have used the Atheros Client Utility (ACU) which confirms that the card and driver are installed and enabled, but the radio does not switch on, so no there is no association/connection with any wireless network!
Reinstalling the original AR5007 works without any problems. If anyone has experienced similar problems and/or can offer a solution, it would be greatly appreciated. Thanks

Thank you MasterG.
I followed the link you posted and you were correct in suggesting that a WLAN card pin assignment was an issue.
On older cards, (before Revision 1.2 of the PCI Express Mini Card Electromechanical Specification), *Pin 20* was +'reserved for future wireless disable signal (if needed)'+, so presumably on my Toshiba Satellite A200, disabling the old AR2007 card was handled by the system software and the Wireless ON/OFF switch.
On the newer adapter cards, Pin 20 is assigned to a *W_DISABLE#* signal which, when low, will disable the radio.
As suggested by other posts, masking Pin 20 on the AR5008 card has prevented the radio from being disabled, and the only small problem with this is the radio can no longer be switched off with the Wireless ON/OFF switch (or with Function+F8).
However, the wireless speed is now 144.4Mbps, enabling BT Infinity broadband download speeds in excess of 30Mbps.
Your assistance is very much appreciated.

Similar Messages

Satellite Pro A10 - No wireless adapter not shown in device manager

Can you Help - Toshiba Satellite Pro A10
Model No PSA15E-01PFQ-EN
Serial No Y3602494G
Windows XP Pro
On the front of this laptop is a switch for wireless - this switch is set to On, Windows XP Pro cannot find any wireless device - Windows Device Manager does not show any wireless adater. Can you advice please - do I need to install Driver - Does this laptop support a wireless conection?
Many Thanks
Owen

Hi
Usually if you have a wireless switch your notebook should have a wireless LAN card too. In your case I would try installing the driver. Then the WLAn card should be displayed in device manager properly:
http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
If this doesnt work you can try a BIOS update.
Are you running factory settings or have you installed your own Windows version?

Memory upgrade on Satellite Pro A200

Have two Satellite Pro A200 #PSAE1E-00T002EN laptops and wanted to know if I can upgrade the 2 x 1GB memory to 2 x 2GB?

As I understand you request, you want to upgrade the notebooks memory to 4GB.
Well, I think its not possible.
The Satellite Pro A200 supports max 2GB RAM (2 x 1GB) so you will be not able to use 2 x 2GB modules.
Best regards dude

Satellite Pro A200-16N: Can I use Recovery CD after upgrade to Vista

Hii!
Im thinking of upgrading to windows vista on my Satellite Pro A200-16N, and i've ran the windows vista upgrade checker from the microsoft website and it says my system will support windows vista so im ok on that.
The problem is, if my laptop were to break or something like that at some point, will my recovery CD's that was supplied from toshiba still work on the laptop with windows vista?
Will they return the laptop to windows xp or since my laptop has a different operating system will they not work?
Also...
Whats the deal with BIOS?:S
I dont understand!
If i were to upgrade to windows vista should i update my BIOS before or after upgrading to vista?
As i have to download the new drivers before upgrading yes?
Thanks!

Of course the Recovery CD will work.
The Recovery CD will set always the notebook back to the factory settings. This means that the whole HDD will be formatted and the Toshiba image will be installed.
> Whats the deal with BIOS? I dont understand!
> If i were to upgrade to windows vista should i update my BIOS before or after upgrading to vista?
In my knowledge this notebook was already delivered with Vista therefore you dont need to update the BIOS if you want to install Vista again.
Some A200 Satellite series needs a BIOS update if you want to use the XP.
In such case its advisable to update the BIOS to XP version firstly and then to install X OS.
Best regards

Satellite Pro A200: Card Reader does not work after XP installation

Hi...
I have removed Windows Vista from my Satellite Pro A200 in favour of XP Home.
I'm much happier with the machine now but am unable to get any response from the Card Reader. There's no mention of it in the User's Manual that came with the machine.
I can't find any reference to it in the Control Panel's Hardware Manager and nothing changes in there when I insert an SD memory card.
I didn't have cause to try the reader prior to removing Vista, so I don't know if it ever worked... although I imagine that it did.
Running a search for a driver in the download section didn't have any success and this forum has no direct answers.
Does anyone have any idea what I need to do to get this to work?
Popa Mintin.

Hi
I dont see any serious reasons why your card reader shouldnt run/function with installed Windows XP.
What you need is the right driver.
The Toshiba driver page provides all Win XP drivers and there is also an XP driver for the multi card reader.
You need a Texas Instruments Flash Media Driver. This is a driver for your Bridge Media Slot.
This slot lets you insert either a SD card, Memory Stick (Pro) or xD picture card.
Cheers

Satellite Pro A200 Windows XP, 4Gb SDHC Card does not work.

Hi,
I have had a Satellite Pro A200 installed with Windows XP, SP2 for some time - No problems there, a great piece of kit. However I recently have bought a new camera and splashed out on a Kingston 4Gb SDHC card. The manual for my A200 seemes to indicate that it my laptop is compatible with SDHC cards to 4Gb however when I push the card in the LED flashes blue briefly and then nothing happens. My SDHC card does not appear to be recognised by the system.
I see no errors in my OS event log and I have checked the slots operation by trying an older 512Mb SD card and that works fine.
Can anybody offer any help please?
For reference this laptop is a Model PSAE4E A200.
Many Thanks in advance
Simon

If the above fix does not work (which it didn't for me on a Satellite Pro A100 running XP), try
[http://support.microsoft.com/kb/923293] .
That one did the trick

Satellite Pro A200 - Fn keys does not work with Windows Vista

Hello,
I own a Satellite Pro A200-PSAE7E and a retail license for Windows Vista Ultimate 32bit (with SP1) installed on it.
Before installing Vista, I upgraded the BIOS to the most recent version available on the Toshiba site ([http://it.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/vista_drivers.jsp?service=IT]).
BIOS version is now 2.20-WIN32 contained in this file: [http://support.toshiba-tro.de/tedd-files2/0/bios-20080404121735.zip]
After the successful installation of the operating system, I installed the "Value Added Package" ([http://support1.toshiba-tro.de/tedd-files2/0/vap-20080109135106.zip]) which contains the "Flash Cards Utility". In my understanding, the installation of the "Value Added Package" should enable the Fn keys usage.
This doesn't seem to be true or not completely true.
Here is what happens.
- Before the installation of the "Value Added Package" all the Fn keys didn't work.
- After the installation of the "Value Added Package", if the TCrdMain.exe process is running, all the Fn keys don't work.
- If I remove the TCrdMain.exe from the startup and I reboot the PC, only some Fn keys work (Fn+ESC, Fn+F1).
There is no way (or I didn't find a way) to make all the Fn keys working.
Does anybody know how to solve this problem?
Thanx in advance,
mme000

I do not know for sure but it can be because of SP1. I have installed Vista Ultimate on A200 and all listed stuff (drivers, tools and utilities) from Toshiba support page.
Does your installations Vista DVD contains SP1 or you have installed it on your own? If you install Vista Ultimate (without SP1) and all stuff from Toshiba support site following Installations Instructions order.

"Common module" missing for XP on Satellite Pro A200

Hello everyone,
I received my Satellite Pro A200 (PSAE7) laptop with a Vista OS.
I have made a fresh & clean XP installation on it using the Toshiba's installation instructions document.
Everything is working fine except my Fn+F6 Fn+F7 Fn+F8 hotkeys for Wireless and screen brightness.
I have made a few search over the internet and I found that page :
- http://support.toshiba-tro.de/kb0/TSB7401VB0003R01.htm
Looks like that I need to setup "common module" installer in order to make work those hotkeys.
But the problem is that the "common module" is not available on the driver page for XP ....
If I change the OS type to Vista there is "Value Added Package" available but it's not compatible on XP ...
I tried to download and setup a "common module" for Sat Pro A120 model but i got an "TVALZ" error during the installation ....
Did Toshiba support forget to put online a "common module" installer for XP for Sat Pro A200 ??
How can I make work my Fn+F6 Fn+F7 Fn+F8 hotkeys ?
Any help will be really appreciated !
Thanks,
Can

Hello darkmatterman,
First of all thanks for you reply and for your tips about the Bios version (Vista vs XP).
The first day I received my laptop on Vista OS, I already made a Bios update "the Vista compatible one". So my Bios is v1.70 actually.
I will try monday morning to update the latest XP compatible Bios version which is v5.20...
Do you know if it's possible to apply the latest XP bios upgrade on a bios which was already been upgraded with a Vista compatible version ?
And if the XP comptabile Bios upgrade works, do you think that I will need to setup my fresh XP again (with all Toshiba drivers & utils setup order...) ?
Regards,
Can

Satellite Pro A200 PSAE4E - WLan speed regularly drops out

Hi
Does anyone know what causes my laptop to lose wifi on a regular basis? It is a Satellite Pro A200 PSAE4E running on XP. I purchased the laptop new back in February and it came with Vista loaded but the wifi kept dropping out and was advise to swap to XP as it was more stable.
When the wifi drops, the Wirless Connection Icon disappears completely from the sys tray as though it never existed although the wifi light just under the front edge remains on. Looking in the network connection in the control panel the wifi is not listed.
I have to shut down the laptop and reboot so that I can carry on working online.
I've downloaded the latest driver for the Atheros AR5007EG and I rang Toshiba support.
Anyone got any ideas - I'm disappointed with the performance of the WLan.

Ive got the same model, and had the same issue with the Wireless Card today (otherwise its been fine for 4 months). I was confused by the card not appearing in the device manager - like it was totally wiped from the system. I rebooted a few times and it did still not appear.
Left the laptop and did something else for a while, and on rebooting the card reappeared and the Wireless connection was remade.
I also have the same question: What causes all trace of a device to disappear - rather than the card to be shown but with an exclaimation mark showing there was some sort of conflict which might help us to sort the cause of the problem.
Have you had any help from anywhere else?

Satellite Pro A200 - Supervisor Password Utility Setup fails

Hello,
I own a Satellite Pro A200-PSAE7E and a retail license for Windows Vista Ultimate 32bit (with SP1) installed on it.
Before installing Vista, I upgraded the BIOS to the most recent version available on the Toshiba site (http://it.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/vista_drivers.jsp?service=IT).
BIOS version is now 2.20-WIN32
After the successful installation of the operating system, I started installing the various drivers and utilities downloading them from the Toshiba site.
When I try to install the "Supervisor Password Utility" the setup fails showing a message box which says "The serial number is invalid".
Same problem with another setup: "Flash Cards Support Utility"
Does anybody know how to solve this problem and which serial number is invalid?
Thanx in advance,
mme000

Hi,
You are having the same trouble as other people on these forums.
If you want to fix it yourself, you would need to look at the disk image on the disk that came with your toshiba, figure out which version of the application was included on that, you might be able to find that version on the website for a different model and different country (for instance, on the canadian website, for a totally different computer than my UK computer, i found a version of the flashcards support utility that works with mine.) But i don't think its possible to see what's on the restore disk without instaling it, i.e. wiping everything off your harddrive in the process.
It really is extremely disappointing and frustrating. If anyone knows a way to communicate directly with toshiba about this problem without having to pay some sort of support fee, I would be very interested to hear about it. It seems noone from toshiba actually reads anything from these forum. It seems like a real wasted resource to me....
Message was edited by: ADMIN

Satellite Pro A200 - Shows only 3GB instead 4GB RAM

Hi,
2 years ago I got a Satellite Pro A200 as a business notebook and it runs with XP SP2, later with SP3. With 2 GB it shows 2 GB of memory in Windows - and I know it has a Radeon 7500 with 256MB of individual graphic memory, and it has no shared memory.
I upgraded it to 4 GB, but Windows shows exactly 3 GB. BIOS shows 4 GB and the ATI system monitor shows 4 GB. I know that 4 GB is not possible in XP 32 bit, only on Windows 2003 R2 32 bit or Vista - but on desktop systems I have seen values between 3.3 and 3.7 GB.
So where is the memory? It looks like a bug - the memory chips have both 2 GB I have verified this. Because it is a company notebook I can't just upgrade to XP 64 bit :-(
In the BIOS are no options - first I thought it's the graphic card, but mine has independant graphics with own memory so the computer comes up with 2048 MB or 4096 after the upgrade.
Shared memory would show about 1900 MB of RAM to the OS like my private EEEpc.

> I upgraded it to 4 GB, but Windows shows exactly 3 GB. BIOS shows 4 GB and the ATI system monitor shows 4 GB. I know that 4 GB is not possible in XP 32 bit, only on Windows 2003 R2 32 bit or Vista - but on desktop systems I have seen values between 3.3 and 3.7 GB.
First of all 32bit OS (no matter if its XP, Win 2003 R2, Vista or Win 7) will not recognize 4GB RAM but only 3.2GB (and not 3.7GB)
I have no idea where you looked for available RAM but you should run DXDIAG in RUN.
Then you should get some details and also the available RAM.
Secondly the graphic card supports Local cache (256MB) and HyperMemory.
HyperMemory of the graphic card depends on the available main RAM memory.
For example the unit supports 1024MB RAM (1GB) then the hyper memory would be 256MB this part of RAM would be shared with graphic card!
This is the reason why the only 3GB are shown...
PS: regarding such comments and a tip:
> hey man please think before you answer.
This is a community and all people here try to help each other so be always thankful for all kind of answers

Satellite Pro A200 PSAE7: Where to get the ATI driver for Win XP

Hi,
I have bought Toshiba Satellite Pro A200 PSAE7 and it was with Vista on from the beginning. I decided to upgrade (/downgrade) it to XP but there's problem with driver to graphic card (Radeon HD 2600 Series).
I can't find anywhere ati drivers (actually I found it on ati.amd.com site, but on this forum I read that Toshiba drivers are modified so that Radeon won't be overheating) and I'm wonderig if Vista ones will run on XP (I've downloaded all drivers but ati one)?
...and is it possible to downgrade my Vista to XP Pro through Miscrosoft site (or something like that) or do I have to reinstall it using my old copy (provided with old Toshiba)?
Ps.
Sory for my English
Ps2.
Is it so important to install drivers in proper order?

> When trying to download driver from Toshiba web I get message:
>"This software has not been officially tested and therefore must be at the users own risk."
>I agree, but still can't download it.
You have to switch the option to Accept!!! Then the button Download will be activated!!!
>I found driver on ati site, but read somewhere that for Toshiba notebooks drivers are modified so that >graphic card won't overheat. Is that true? Or original drivers (of ati group) are as good as Toshiba ones?
As mentioned in this forum, the original ATI or nVidia drivers are designed not for the notebook usage!!! The GPU drivers are designed for the graphic cards which are used in the desktop PCs!!! Such graphic cards are equipped with an own, big cooling module in order to prevent the hardware from overheating!!! The notebook GPUs dont support such huge cooling modules and therefore the drivers must control the performance and the temperature growth.
regards

WXP WLAN Driver installation on Satellite Pro A200

Hello,
I installed Windows XP SP2 for a customer on Satellite Pro A200 (PSAE7E) and installed after is talked to the German support hotline every driver like in the test-instal.txt but I don't get the Atheros WLAN card work.
It is an ar5bxb72 from Atheros, but no way.
I get every driver in that list working with the hardware but not the WLAN-card although I installed it like in the list.
Anybody got a hint for me?
Greets
Marco

Hi dude
Are you sure the notebook was equipped with the Atheros WLan card? According to some information which I found in the internet, this notebook was delivered with Intel or Atheros WLan card!
I have checked the Toshiba page provides an Intel WLan drivers and Atheros Wireless Lan Client Manager. The Wireless Lan Client Manager is not the driver but only the tool which helps you configure your wireless network card and gives you more configuration options than the windows embedded configuration functions.
I would recommend downloading the WLan driver from this Toshiba WLan portal:
http://aps2.toshiba-tro.de/wlan/
By the way; if you use XP on this Vista preinstalled notebook then you will have to update the BIOS to the XP version too!
Greetings ;)

Satellite Pro A200-PSAE7: Blue Screen error - ati2dvag infitive loop

I've got Satellite Pro A200-PSAE7 with ATI HD2600 Mobility Radeon. I've downgraded to XP SP2. I get blue screen saying that ati2dvag went infitive loop quite constantly. Any solution to this?
Offtopic: Why standart display drivers from ati.com does not work? (while on my friends laptop with also hd2600 mobilty radeon works fine).

Hi
> I've got Satellite Pro A200-PSAE7 with ATI HD2600 Mobility Radeon. I've downgraded to XP SP2. I get blue screen saying that ati2dvag went infitive loop quite constantly. Any solution to this?
Usually the BSOD appears due to the serious software issue or hardware malfunction.
In my opinion its a software (driver) issue.
I presume the BSOD appears why playing some games in most cases the graphic driver must be updated.
If the XP driver from the Toshiba page will not help you could try the graphic drivers from the www.omegadrivers.net site. The 3rd party drivers should run on your notebook. But note; 3rd party drivers can be used only at your own risk!
> Why standard display drivers from ati.com do not work? (While on my friends laptop with also hd2600 mobility radeon works fine).
The original ATI drivers cannot be installed on a easy way because such drivers dont support an overheating protection. The Toshiba GPU drivers are a little bit modified and support an overheating protection. Such protection is necessary and important because the notebook graphic cards are not equipped with huge cooling module like the GPUs on for the desktop PCs.
The temperature increases on the notebooks much faster and therefore the graphic driver have to control the GPU performance to decrease the internal temperature.
Therefore its always advisable and recommended to use the Toshiba drivers ;)

Satellite Pro A200 - Can't install Windows 7 due missing CD/DVD driver

Hello, I have a Satellite Pro A200, PSAE4E-046018N5 and I'm trying to install Windows 7 but I can't pass from step one because it doesn't found a driver:
A message box saying: A required CD/DVD drive devise driver is missing. If you have a driver floppy disk, CD, DVD or USB flash drive, please insert it now.
-What to do?
CD-ROM is a HL-DT-ST DVDRAM GSA-T20N ATA, the actual driver have version 6.0.6002.18005 (date:2006-06-21)
Best regards
/peter

Hi Peter,
Do you try an upgrade from Vista to Windows 7 at the moment? If yes please try a new and clean installation of Windows 7. Does this work?
Another question: Is your CD/DVD drive working properly or is it listed with yellow exclamation mark in device manager?
In your case I would try to remove the drive from device manager and restart the notebook. After this the drive will be recognized automatically.

Satellite Pro A200-16YT - Wireless adapter card upgrade to 802.11n

Similar Messages

Maybe you are looking for