Satellite Pro A300 PSAGDA-02000R CPU and video card chipset mismatch

can anyone help me with the specs on this laptop.
When I look at the official toshiba brochure for this product it mentions that the CPU Chipset is
"Mobile Intel 965PM Express Chipset"
but the second video card says
"Intel Graphics Media Accelerator GM45"
Which is correct because what I've read on the intel website, the GMA X3100 is used on the mobile 965PM Express Chipset.
Any help will be much appreciated.

To be honest this unit is not known to me but I know that some other Satellite Pro A300 supports other chipsets;
For example:
SATELLITE PRO A300 PSAJ1E-005008BT supports Intel GM965 chipset and Intel GM965 graphic chip
SATELLITE PRO A300 PSAJ5E-001001GR supports Intel PM965 chipset and ATI Mobility Radeon HD 3470
SATELLITE PRO A300-1E7 PSAGDE-003003EN supports Intel Mobile PM45 Express Chipset and ATI Mobility Radeon HD 3470
SATELLITE PRO A300-1HF PSAG1E-00K00SIT supports Intel GM965 and Intel GM965 graphic chip as well.
SATELLITE PRO A300-21B PSAGDE-01S007A3 supports Mobile Intel GM45 Express Chipset and ATI Mobility Radeon HD 3470.
As you see there are many different notebook models with completely different hardware components
I googled too and it seems that the Satellite Pro A300 PSAGDA-02000R supports Mobile Intel 965PM Express chipset and graphic card ATI Mobility Radion, HD 3650 with 512MB + Intel Graphics Media Accelerator GM45.

Similar Messages

Satellite Pro A300 PSAGDE re-booting when plugged in

I have had this laptop put away for a while as I couldn't work through this problem, but I'm having another try.
The laptop is a Satellite Pro A300 PSAGDE.
The problem I am haiving is that the laptop would re-boot whenever I connect the PSU, but not when using a live CD (Ubuntu).
I would like to try and flash a replacement BIOS to see if that will solve the problem.
Unfortunately the software needed to flash the BIOS requires the laptop to be plugged in.
Is there any way around this problem?
Can I fool the software into thinking it is plugged in?
Is there a way I can revert/repair the BIOS in any other way as obviously the problem hasn't always been there.
Thanks
Message was edited by: miainphillips
Message was edited by: miainphillips

So once again: notebook runs fine using battery power but reboot always (in the loop????) when AC adaptor is connected. But using Live CD the notebook runs ok even if the AC adaptor is connected.
Right???
>> I think it may be a BIOS issue because the laptop will run without an issue when booting a live cd, even when it is plugged in.
If the unit runs ok using Live CD, then this means that this cannot be BIOS issue because BIOS does not depend on installed system.
Therefore in my opinion its definitely not a BIOS problem.
I think you should firstly disable the automatic reboot when an system crashes Win 7 is configured to restart immediately when a BSOD happens and this happens too fast to see the error I think you mean this by automatic reboot
Disable this by following way:
1)Control Panel -> System & Security -> System -> click the Advanced system settings
2)Locate the Startup and Recovery section near the bottom of the window and click Settings button.
3)In the Startup and Recovery window, uncheck the check box next to Automatically restart.
4)Now click OK and restart the unit
In my opinion the system crashed and therefore the notebook reboots

Satellite Pro A300 PSAGDA: Problems installing webcam on Win 7

Hi there guys,
its been a few weeks since installing Windows 7, only for the last few days have i actually bothered to install toshiba software (dont stone me!).
Right now I've been scratching my head when installing the webcam drivers. When the install is done and after a reset, all it says is Webcam failed to initialize, please restart cam or computer.
Restarting the laptop wont do anything
I am using a Toshiba Satellite pro A300 PSAGDA-01C00R, do these drivers simply not work for the time being on 7?
any help would be great, thanks!

Hello
I have installed THIS version of webcam driver on my Win7 preinstalled Satellite A300 and it works perfectly.
I have tested preinstalled software and it runs well. I have also tested it with Skype. No problems at all.
Test it on your Satellite too.

Satellite Pro A300-28R: slow boot and freezing on Explorer/Internet

I have recently bought a Satellite Pro A300-28R and I am quite disappointed about the performance.
1) From the specs it looks like a decent laptop but with booting time of about 3 minutes, "please wait" it is surely not impressing me given the fact that i have not installed anything yet...
2) I will try to uninstall applications like tempro but still I am puzzled by the slow reaction on internet pages.
For example when i go on google and start typing something most of the times the cursor freezes and i have to wait a few seconds before I am able to see what i am typing.
I have only bought it last Friday and I have not used much but surely a bit of a disappointment so far.
Any ideas why the cursor freezes on google or on the internet explorer toolbar?
for info i am using Vista Business OS and Internet explorer
any help welcome

Hello
About slow boot you can read very interesting and useful thread under http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=134947
I hope this will help you to understand why this can happen.
After first start you can be faced with this behaviour. Few days updates will be downloaded and installed in the background and you will notice high HDD activity. These activities can slow down notebook performance and what you can notice is this slow typing reaction or freezing video play.
So my advice is to disable automatic updates and set it when updates are available you should get notification but you can start it manually. These all possible vista updates installation is for me big mistake because if you check available updates many of them are optional and some of them are driver updates (3 of them) these updates must not be installed.
Maybe you should install recovery image again. don't connect it to internet and do what is described in posted thread. After optimizing preinstalled OS change settings for Windows update and connect it to internet. Check list of available updates and install important and recommended stuff only.
I do always so and I am happy with my Satellite P200 and new A300. Both of them runs well and I am satisfied with performance.

Re: Cannot find drivers for Satellite Pro A300-1HE (PSAGDE)

Hello,
I have a Toshiba Satellite Pro A300-1HE (PSAGDE-00800QFR) with the serial number 78621314Q, but i find it anywhere on the toshiba site.
I'am looking for drivers for the graphic card ATI, it has an ATI Mobility Radeon HD3650.
Where can-i find drivers for this machine ?
Thanks by advance

Hi
Go to Toshiba EU driver page
http://www.toshiba.eu/innovation/download_drivers_bios.jsp?service=EU
_Choose:_
Notebook
Satellite Pro
Satellite Pro A
Satellite Pro A300
PSAGDE
Thats all.

Cooling fan is not working on Satellite Pro A300

Hi Everyone
I was asked by a friend to repair their Satellite Pro A300, as their CPU Cooling Fan had stopped working even during POST bootup and the laptop would overheat and shutdown. So I thought it could one of three things:
# Fan is clogged with dust or dirt
# Fan bearing has failed
# Fan power cable was loose
So I disassembled the laptop and cleaned the fan/heatsink using compressed air and checked the power connection which was solid, but this did not solve the problem, so I replaced the fan and heatsink with another one that I knew worked from the same model laptop that had a fault motherboard because of the random bios boot-up password bug (out of warranty) but still no joy.
I am beginning to believe that the fan was perfectly fine rather the motherboards cpu temperature sensor(s) that control the fan activation has failed.
Am I correct, in thinking that this is basically, irreparable without specialised tools and my friend will have content themselves with turning the system off every hourish or is there something else I am overlooking?
Thank you, for any help.

Hello
Im not a technician but for me it sounds like that fan connector is malfunctioning if you have already replaced the fan and therefore it would be necessary to replace the mainboard
Thats everything what I can say about this Have a look for second mainboard or notebook where you can get a cheap mainboard. Maybe it works. :)

What CPU would work on Satellite Pro A300-2C2

I know far more about desktop computers than I do laptop computers,
However last night my laptop completely froze and held the current sound (making a kind of buzzing sound).
I thought nothing of it at the time however it wasn't coming responsive again so I held down the power button and went to sleep. When I awoke this morning I booted up my laptop, but it did not boot.
The motherboard is not broken as it is givin power to lights and disc drives ect...
I am basically wondering what CPU's will work in the a300 2c2,
I HOPE it isn't soldered in but I have not confirmed that yet as I have to go out in a moment, thus I cannot open her up.
Thanks in advanced,
TheUnknown

> I am just wondering if you know if/where I can find a list of CPU's that were used in the A300 over time, I am thinking if they were compatable down the line mine should accept it, right?
Indeed, the usage of the same CPUs which were used previously in other Satellite Pro A300 should be possible.
I read somewhere in the internet that Toshiba Satellite A300 /Satellite Pro A300 and Equium A300 are similar series and used CPUs should be compatible.
The chipset seems to handle the Penryn and Merom CPUs.
_Penryn CPUs are:_
Intel Core2 Duo Processor (800MHz)
T8100 (2.20GHz) / T8300(2.40GHz)
T9300 (2.50Ghz) / T9500(2.60GHz)
_Merom CPUs are:_
Intel Core2 Duo CPU (800MHz)
T7800 2.6GHz
Intel Core2 Duo CPU (667MHz)
T5250 (1.50GHz) / T5450 (1.66GHz)
T5550 (1.83Ghz) / T5750(2.00GHz)
Intel Pentium Dual Core CPU (533MHz)
T2330 (1.60Ghz) / T2370(1.73GHz)
Intel Celeron CPU (533MHz)
540 (1.86GHz) / 550 (2.0GHz) / 560 (2.13GHz)

Satellite Pro A300 standby and hibernate functions not working properly

I have a new satellite Pro A300 PSAJ1E - 01E00VIT, and I'm finding this problem:
Sometimes, (not always: may be it depends on which program is running) when trying to put the computer in stand-by or in hibernate mode, it doesn't stop, but only shuts down the monitor (panel), while the fan goes on running and the power light is green. Obviously, lots of battery energy consumption!
Then there is no other way of resuming than shutting down the computer by holding down the power button long time... but this is not correct!
NB: my computer is always connected to a lan, and generally there are some browser windows open when I put it in stand-by mode.
How can I fix this?
jomurray

Generally you are right but the point is that you have said that this issue doesnt happen always but sometimes.
> Sometimes, (not always: may be it depends on which program is running) when trying to put the computer in stand-by or in hibernate mode, it doesn't stop
Fact is that some single applications which are running can prevent the execution of standby mode or hibernation mode.
Therefore if you are running such programs you will have to close it firstly.
I dont say that this must be done with all applications. ;)

Satellite Pro A300 crashes with blank screen

I have a Satellite Pro A300, AMD CPU, ATI graphics, Vista.
The system worked fine for a year but a few months ago it started crashing, the screen went blank, not blue, anything running, like music, stopped. This can happen after several hours or minutes, or even whilst it is re-booting. All my software is up-to-date, both from Microsoft and Toshiba. I have rebuilt my system from scratch and the symptoms came back.
At first I thought this might be a heat problem but I have monitored this but I don't think this is it. It has crashed seconds after leaving sleep mode when it has not had a chance to warm up.
Anybody got any ideas?
Simon

Hi buddy,
Theoretically it could be an overheating problem so the screen went blank due built in overheat protection...
You should try to clean your notebook using compressed air spray. This could blow out the dust from the cooling ventilators and therefore its not necessary to disassemble the notebook.
In your case I would recommend reading this article:

Satellite Pro A300 - Overheating

Hello,
It has been a year and a half since I got my Satellite Pro A300. Just a week ago it started overheating very badly. At low CPU usage it maintains its regular temperature of 55 - 60C (given the hot summer weather).
However if I try to do anything CPU heavy, the temperature gets to 100C in a matter of minutes and the laptop shuts down. The fan is working, except that it does not seem to generate as powerful air stream as usual, which made me think that it was clogged. I disassembled the laptop, but I could not get to the cooling unit because of the three cables connecting the motherboard to the plastic shell, which have white T shaped connectors that for the live of me I could not pull out even a little bit. Nevertheless, I cleaned what I could with compressed air, and a little dust was cleared, but the fan/radiator did not look clogged at all.
After putting it back together there is no noticeable difference.
I am certain that this is a new phenomenon as I've been running the machine in much hotter weather in worse conditions with CPU loads close to 100% with no trouble. I checked all settings, just in case something had toned down the fan, but the power saver utility is set to "Maximum Performance".
I would appreciate any ideas and help, even just tips on how to disconnect the motherboard cables.
Thanks in advance.

Hi buddy,
I agree with the user above: Cleaning procedure from time to time is really important and if compressed air spray doesnt help it must be done by professional people from an authorized service provider. They can disassemble the whole notebook and clean every part well. You can find a list of service providers here:
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider
Notebook disassembling is not easy so it should be done from professional people. Just ask the guys for help ;)

Satellite Pro A300-1E7 - cannot start cam software

I have purchased the Satellite Pro A300-1E7.
Webcam is not functioning properly in MSN messenger video call.
Am having similar problems to the previous posting except I am using Zonealarm.
I think Zonealarm challenged cec_main.exe in a similar way.
I have tried to follow the instructions on here but without much success.
I removed Camera Assistant SOftware and re-installed the driver but doesnt appear to have improved things.
Now c:\program files\ camera assistant software for Toshiba has disappeared altogether and the the camera assistant panel no longer appears on the side of the desktop.
Any ideas please?

Hi
I used the Zonealarm is the past and I was not really satisfied because this software locked everything and most applications didnt work properly even after new configuration! Finally I removed this software and I noticed further advantage; my notebook boots much faster!!
I think this software would lock the cam software too.
> Now c:\program files\ camera assistant software for Toshiba has disappeared altogether and the camera assistant panel no longer appears on the side of the desktop.
This would mean that the software was removed and was not installed properly.
But to be sure, check in control panel -> Software (add & remove programs) if the webcam software is installed.
Ive got the internal Chicony cam too and its working fine in connection with Skype software. I didnt test MSN but I dont see any serious reasons why it shouldnt work.
In my opinion you should firstly remove the zonealarm. Then clean the OS using CCleaner. Finally download the webcam software again and reinstall it!
The webcam toolbar is not always visible on desktop.
It would appear only if you move the mouse cursor to the place where the webcam toolbar was hidden.

Cooling behavior after BIOS Flash - Satellite Pro A300

Hello everybody,
I have two laptops, Satellite Pro A300 and Satellite A300. Both have the same configuration, C2D E8300,2GB,ATI 3650 512MB and so on.....
Today I flashed BIOS to the latest version (from V3.90 to V4.20) on both of them. On the version 3.90 cooling was OK, fan worked only when it was necessary. But now after flashing the BIOS fan works permanently, it does not stop.
What I did make, in Vista's Power Options under Toshiba Power Saver I changed the Cooling Method from Maximum Performance to Battery Optimized, the cooling reversed to the normal operation, but the cover (keyboard area) became hot a little bit.
My question is, what is the problem with cooling in the new version (v4.20)? And how to solve this problem?
Again, problem didn't exist before BIOS flashing and the problem is on both computers.
Thank you for your help!
Best regards,
Osman

Hi mate
Thanks for the feedback
> So what do you recommend me, to stay on Battery Optimized mode? Generally speaking, what's the difference between Maximum Performance and Battery Optimized modes in Power Saver?
Usually its advisable to use the Battery Optimized mode only when the AC adaptor is not connected to the notebook and the notebook uses only the battery power.
In such case the notebook does not waste the power using Battery Optimized mode and you could use the notebook much longer using battery only.
Using Battery Optimized mode the CPU and cooling modules run with lowest performance and the CPU does not create high heat dissipation.
This leads to a lower internal temperature and lower usage of cooling modules.
Bye

Satellite Pro A300 PSAG9C-01500Y - FSB question

Hello, I was wondering if anyone could give me some advice on possibly upgrading my new [Satellite Pro A300 PSAG9C-01500Y|http://www.toshiba.ca/web/product.grp?lg=en&section=1&group=1&product=8270&p art=8813#spectop] to a different model.
I do not use this system for gaming or anything like that, mostly Office 2007, web browsing, media and programs like Photoshop and Dreamweaver. Nothing too high end.
My model has 800MHz, but after looking at a few different models I see that for $100 or so I can get a higher FSB speed (1066MHz) Like the model [PSAG9C-01J00Y|http://www.toshiba.ca/web/product.grp?lg=en&section=1&group=1&product=8270&p art=9131#spectop] which has a little faster CPU as well.
One of the things I have noticed as well is the max Ram for my system is 8GB and most others are only 4GB. I will not be using 64 bit windows, so it doesn't matter anyway.
I would mainly like to know if it is worth worrying about the FSB. I understand how FSB works and what it does, I am just not sure if i need to worry about it.
Any advice or suggestions are most welcome.
Thanks in advance,

Hi
In your case the FSB speed is not really important if you want to use your notebook only for Office 2007, web browsing or webdesign.
The higher FSB is useful if you want to use high performance memory modules with higher speed.
For example; youve got FSB of 533Mhz and memory modules of 800Mhz the inserted memory modules would NOT run at 800Mhz because the lower FSB would slow down the memory speed.
But as I said a higher FSB is not really important if you dont use the notebook for high-end gaming.

Satellite Pro A300-28R - Windows starts up with wrong display resolution

OK so I have a Toshiba Satellite Pro A300-28R with Windows 7 64 bit and an ATI Mobility Radeon 3470 HD graphics card.
I recently connected my laptop to a TV via the S-video connection. This worked fine. The problem is that ever since then every time I start my laptop Windows starts with the S-video display resolution of 600x800.
I have tried changing the settings in both Control Panel and using the ATI CCC, having both selected and applied these settings but each time Windows starts now it boots with the above display resolution.
Following this I have also uninstalled and reinstalled both my display driver and the Toshiba Value Added package but the same problem persists. I have searched with Google about this problem and haven't been able to find anything useful.
Any help would be greatly appreciated.

Hi thanks for your responses! Originally I used the method of closing the laptop screen while connected to the s-video and then opening the screen and logging into Windows. This then automatically detects the display and changes to that output. To get out of this you can do either do the reverse or pres Fn+ F5 to undo. This has worked perfectly for me before with VGA connections. Its only since connecting to s-video that now no matter what, every time the laptop starts up even when it is not connected to any external display, it loads with the resolution 800x600. This is not the first time I have used s-video, but it is the first time I have had this result after doing it.
Interestingly if I change to the appropriate resolution and do a restart. The system restarts and loads to the logon screen and then into Windows in the resolution I specified before the restart but then after fully loading Windows it then changes to 800x600. It is as if the laptop is detecting that there is something connected to the s-video when there is not. I have read a fix for this whereby you can go into the system registry and turn off the feature for automatically detecting displays but I use external displays frequently and this is not a satisfactory solution. This worked perfectly before.

Satellite Pro A300-1GT - Error message when starting webcam

I have a Toshiba Satellite Pro A300-1GT. The problem is that the camera does not work. When I start software it writes that I should restart camera or computer. I'm having Windows 7 and I serched the internet for solutions but I find just a discusions with the same problem without solutions.
Sory for may bad English.

Hi
The cam is not listed in device manager; neither as unknown device nor as USB device?
Well, I read here in the forum that internal webcam is connected to the USB controller on the motherboard and sometimes the connection is loose and therefore the cam cannot be recognized by system.
I think in such case the notebook needs to be disassembled and the connection should be checked. But this seems to be a job for technicians

Satellite Pro A300 PSAGDA-02000R CPU and video card chipset mismatch

Similar Messages

Maybe you are looking for