Satellite Pro P300: Error after BT stack 8.00.02 installation WIN 7 32bit

I Upgraded my Satelite Pro P300 from Vista to Win7 Pro 32-bit.
The existing drivers and programs had (compatibility) issues with Win 7 whitch was indicated when installing Win 7 Pro 32bit.
So I download and instal this newest stack.
In the hardware devices there are 3 BT ports. But the software, (settings, communcations, etc) does not start..
by example: BtAssist.exe - runtime failure (dutch: toepassingsfout), Cannot correctly start this applicaton (0xc00000be, click Ok to exit).
Anyone any Ideas?
Every thing worked fine before installen Win 7.
Thanks already
Eric

Hi
Did you make a clean Win 7 installation or did you upgrade the Vista to Win 7?
I recommend a clean Win 7 installation. This is better because an upgrade from Vista to Win 7 could leave some junk on the HDD and some Vista tools/drivers would not be fully compatible with the Win 7 OS.
So make a clean Win 7 installation and then download and install the newest BT stack from this page:
http://aps2.toshiba-tro.de/bluetooth/
Good luck

Similar Messages

  • Satellite Pro P300 has just died on me

    Hi,
    Yesterday my Satellite Pro P300 (PSPC1E) simply died on me...no battery charging lights nothing. Nothing happens when I press the ON button it is DEAD.
    The battery was ok last time used, the adapter is still giving me nearly 20volts.
    I took the laptop apart to check the DC in connector, thats ok.
    I assume after some research its a motherboard fault. Typically my warranty ran out 2 months ago!!
    Cost of a new replacement motherboard so far quoted is 180, not too eager to spend that as I have a tax bill to pay at the end of this month!
    Any ideas to what the problem could be?
    I have found a mobo on eBay which is a p300-1a8 going for a song but would that be compatible?
    What are all the variations in the motherboards?
    Would any other motherboard be compatible?
    Any ideas, suggestions would be much appreciated and I thank anyone in advance for any ideas.
    Cheers
    Steve

    Yes and no.
    You can also imagine that different P300 notebooks have also different ports. Some of them have HDMI some probably not. There is also the difference.
    Different ports, different processor or different graphic card. Maybe some models don't have even webcam and missing controller on motherboard.
    So, if you want to have identical hardware configuration please be sure you use motherboard with the same model number.

  • Satellite Pro P300 (PSPC5E) - Webcam driver open fail on Windows 7

    I've installed the RC of Windows 7 64 Bit on my Satellite Pro P300-PSPC5E and I'm experiencing problems with the configuration of my webcam and microphone.
    I've tried to install the camera assistant software, 64-bit (windows vista) to configure the webcam but I keep getting an error with 'Webcam driver open fail. Please restart camera or computer.' neither of a camera or computer restart work. I do get picture in Skype but I can not edit settings or so (dark picture) and the microphone is way more silent then it was on windows XP, although it's set on the maximum sound.
    Is there a solution for this problem? I hope so :)

    Hi
    I think there is no solution for this problem at the moment because you are using a Release Candidate of Windows 7 and at the moment there are no official drivers for Windows 7 available.
    You have already tried the Windows Vista driver so thats all what you can do. Alternative you visit the Toshiba US page (http://www.csd.toshiba.com) and search for Windows 7 beta driver. Maybe it works.
    Good luck! :)

  • Recovery CD for XP in combination with dual HDD on Satellite Pro P300

    On my Satellite Pro P300 there are two harddisks, both 160 GB.
    At the moment Windows Vista Business is installed, as it was preinstalled.
    On the first disk there are 3 partitions, one EISA-partition, one Vista boot-partition and one partition for HHDRecovery (contains image for Vista Product Recovery).
    In Vista there is an option for Complete PC Backup. This provides the possibility to completely restore Vista to the situation at the time of the backup.
    I made a Full PC Backup of the complete first hard drive (3 partitions) and saved it on the second harddrive.
    Now I want to use the provided Toshiba Product Recovery for Windows XP to install Windows XP on the laptop.
    I assume that the first harddrive will be completely overwritten, but I am not sure if the second drive will also be overwritten.
    Does anybody know if my data on the second drive will be lost when i use the Product Recovery for XP?
    I would like to preserve the data on the second drive, because it gives me the option to restore the laptop to the situation with Vista without reinstalling/activating all applications.
    Also all my personal files are on that drive.

    Normally it would be no problem to temporarily remove the second harddisk.
    But I am not sure if my warranty will be void after that; the machine is only a few weeks old.
    If the warranty is still valid after removing and reinstalling the second harddisk, I will try that option.
    I just wonder if anybody knows for a fact that it does not write the second harddisk.
    As you said, I also assume that it will not write the second harddisk, but I just want to be sure.

  • Satellite Pro P300-26U - Can I use a second HDD?

    Satellite P300 family support raid0 and double HDD. All model? User manual of 26U don't say any word about this. Model like P300-1BP has double HDD.
    Can someone help me? I want to buy a P300-26U in Italy.
    Thanks.
    Guido

    Hi
    The Satellite P300 series doesnt support RAID!
    There is NO RAID controller on the motherboard.
    But you are right; the Satellite Pro P300-BP supports 2 HDDs but this does not meant that it would support RAID!
    Furthermore you should know that P300 series supports different hardware specifications.
    This means that not all P300 would be able to use 2 HDDs!!!
    It could be possible that Satellite Pro P300-26U is not able to use 2 HDDs even though the Satellite Pro P300-BP support 2 HDDs.

  • Satellite Pro P300 - HDMI output port doesn't fit

    Hello All,
    Well this is starting to drive me to distraction and Im hoping theres someone who can put me out my missery lol.
    I have been trying to hook my laptop (toshiba satellite pro p300) up to my LCD TV via the same HDMI cable I use for my PS3 but the connector just wont fit. I keep finding all these posts in various forums saying how they cant get sound out the HDMI connection...that would be great, as at least that means they have them connected.
    Are there different connections for HDMI? The one I have is diagonal connector but the port on the laptop is more square, and just doesnt fit. So if there isnt a connector, does that mean I have a funky port, on the laptop.
    There is also the matter of connection my laptop to my amp that controls the surround sound system. What connection is best to use, as there is no real audio out connections?
    Cheers

    Hi
    Can you please tell us what Satellite Pro P300 you have exactly? I mean the exact model number.
    Maybe you can also post a picture of the HDMI port. Normally there are no different HDMI ports, all have the same physical dimension.
    Im not PS3 owner but maybe it has a special connector. Have you tried another cable?
    Regarding the audio connection I use the normal line out port for my external speakers. Did you test this?

  • Satellite Pro P300-1CG wakes up from sleep mode when unplug USB mouse

    I often transport my laptop from one working place to another.
    Usually put it into sleep mode, unplug the USB mouse and lay in the bag.
    However every time I unplug the USB mouse - the laptop wakes up and I have to put it into sleep again.
    This is annoying. Is there any way to set up laptop _not_ to wake up on USB activity?
    I didn't find any option in power settings of Vista, neither in BIOS.
    My BIOS is up to date (just updated, but didn't help).
    I use Windows Vista Business on Toshiba Satellite Pro P300-1CG.

    Hi
    > Usually put it into sleep mode, unplug the USB mouse and lay in the bag.
    Why you dont unplug the USB mouse firstly and then put the notebook into the sleep mode?
    This would solve your issue ;)
    From my knowledge the BIOS provides only the options: Wake-up on keyboard and Wake up on LAN.
    There are no options for Wake up on USB and therefore such settings cannot be changed...
    Cheers

  • Satellite Pro P300 - unable to activate the inbuilt microphone

    I purchased a Satellite Pro P300 some 2 months ago and to date all is well.
    It has a webcam which I really thought I would not have any use for it but now find that I have.
    The camera works fine but I am unable to activate the inbuilt microphone.
    Can someone point me in the right direction please

    Hi
    You have to start the webcam software if you want to use the internal mic too.
    The point is that the internal microphone is connected with the internal webcam and the webcam software controls the both devices.
    Please check also if the internal mic was enabled in the webcamsoftware correctly
    Furthermore I would recommend updating the sound driver.
    Best regards

  • Satellite Pro P300 - How to obtain the factory image without media?

    Hello
    I have been given a Satellite Pro P300 and it has the recovery disc for win xp, I would like to go back to the pre installed Vista intallation if possible.
    The recover partition on the hard drive isnt available so i assume it cant be recovered. Is it possible to purchase a factory image?

    Liam is right Win 7 is better than Vista OS.
    So if you have a possibility to install Win 7 I recommend doing this instead of Vista.
    However, the Toshiba recovery disk contain just Vista OS.

  • Satellite Pro P300 - After Truesuite update I can't open protected files

    Hi,
    sorry for my bad english but I came from Italy and here we don't have any forum who can resolve my problem.
    I've got a Toshiba Laptop pro P300 with fingerprint reader. I use fingerprint to logon and protect some files, just for curiosity, it seemed cool...:|
    The problem born when I recently update "truesuite access manager". Since I did the update I can't open protected files, I didn't read that I have to remove the protection before the updating (damn...), but these files are important for me and I have to open them again.
    To resolve the problem at first I restore the system before the date of the update, to have the old version and open these files again, but all my fingerprints are deleted and I can't create new fingerprints because the pc says that it "can't open the sensor". I don't know what it means.
    I thought that it needs some drivers, so I reinstalled truesuite access manager several times, I reinstalled BIOS, I've done the scan disk and the toshiba diagnostic, but the sensor still doesn't work.
    I think that if I can save a fingerprint with the old version of the program I will able to open protected files again (and I will not protect them anymore) because only the old version of the program knows how to decrypt these files, but I don't know how to turn the fingerprint sensor on. Someone could help me, please?
    Thank you so much!

    The Truesuite update come from the Toshiba website. I can open the Truesuite program with my fingerprint but I can't decrypt files because it says that I don't have the correct "key of protection" or the "protection code keyAC 3000" of the file.

  • Win 8.1 activation issues on Satellite Pro C850-1EQ after upgrade

    Hello everybody!
    I face a problem after upgrading my TOSHIBA SATELLITE PRO C850-1EQ preinstalled windows version 8 to 8.1.
    After installation windows demands the product key in order to activate windows 8.1, but I haven't this activation key.
    I called Microsoft (Greece) but couldn't help me and told me to call Toshiba (Greece).
    The man from Toshiba's technical support told me to call back to Microsoft!
    Also, he told me to check here (https://www.toshiba.eu/innovation/generic/windows8_1-upgrade-stepbystep/) before I start the process. Step No. 7 says "Remember your Windows password. You may need to enter it after updating."
    Now I returned back to Win 8.
    Is there a way to learn my activation key before the installation of w8.1?
    I tried to find that using various tools but no one finded the key.
    Plus, after the installation of 8.1, a message says:
    +Error code: 0xC004C003+
    +The activation server determined the specified product key has been blocked+
    I trust Toshiba and I want to use the latest version of w8.1.
    I would be greatful if someone technician from Toshiba could help me with this issue.
    John (from Greece)

    Hi
    Yes, the preinstalled *gets automatically activated* when I restore or refresh my pc and I do not need the activation key.
    When I upgrade to windows 8.1 it asks me the activation key in order to activate the new version.
    Before the upgrade, yes, I updated win 8 and the drivers too. I always keep my pc updated.
    What do you mean:
    +Try this: create the Toshiba Recovery DVDs (or USB flash memory stick). Use the Recovery medium in order to recover the notebook back to factory settings. Update the Windows 8 to latest state and then perform the upgrade to Win 8.1+
    Windows 8 is in a hidden particion in my PC, so I don't need to create recovery disk.
    Or do you mean anything alse?
    Thank you for your reply

  • Satellite Pro A300D - Error message while watching DVDs

    Hi There
    I have a problem with my satellite Pro A300-140 running Vista 32-bit OS
    Every time I try and watch a DVD I get an error message " Unable to output the video to an external device. Please check the external output setting after ending the application "-I am not trying to connect to anything - I just want to watch a movie !
    Any ideas - I did read this was a known problem but I can't re-find the information ?
    Thanks

    Hi
    You should try the new Realtek sound driver from the Realtek page:
    http://www.realtek.com.tw/
    Furthermore I recommend updating the Toshiba DVD player. It's placed on Toshiba European driver page.
    Just one tip; Im using the VLC player. Its free software and very nice
    It plays almost all video and audio formats google for VLC player!

  • My Xperia Mini Pro Touchscreen error after install Custom Rom , and now Bricked / Bootloop

    Hi There. .
    I've some problem here. .
    My Xperia Mini Pro SK17i Touchscreen error after install Custom Rom , and now Bricked / Bootloop
    I've tryin' to use Flashtool and flash Stock Firmware, but it still bricked. .
    Any body may have a sollution for me?

    *Moved to Android development*
    Hopefully you can get some help here.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Satellite Pro L300: BSOD after BIOS update

    Hi
    after update the Bios of Satellite Pro L300, the windows not start!
    Its show the blue dead screen!
    What can i do?

    Hi
    Are you able to access the BIOS settings?
    Im not quite sure why this BSOD appears but possibly the SATA mode settings have been changed after BIOS update
    Usually the SATA mode should be set to AHCI if the SATA drivers are installed.
    But if the SATA drivers are not included the SATA mode should be set to compatible.
    Please check this!
    Furthermore you could set the BIOS to the default settings and could try to boot the machine again.

  • Win XP Display driver for Satellite Pro P300 PSPCDE requested

    After a clean XP installation I cannot install a proper display driver (Radeon 5145).
    No driver is offered at Toshiba's website.
    Is there any idea what I could do?
    Please help - thank you!!

    Hi
    From my knowledge this graphic card was built in other Toshiba series too.
    Satellite L500 PSLS9E
    Satellite L505 PSLS9E
    Satellite L550 PSLWSE
    Satellite L555 PSLWSE
    Satellite L630 PSK04E
    Satellite L650 PSK1JE
    Satellite L650D PSK1SE
    Satellite Pro L500 PSLSAE
    Satellite Pro L550 PSLWTE
    So try the drivers released fort the series listed above.

Maybe you are looking for

  • T440p Fingerprin​t power-on is not working

    Hi , i just recieved my new T440p ,  Fingerprint @ power-on is not working although all config. is done typically in lenovo fingerprint manager pro & fingerprint security settings in the BIOS , i start my laptop it goes through windows normal startup

  • Random lock ups/ reboots on iPad 4 on IOS7

    Just started noticing random lookups and reboots when using safari for extended period of time.  My ipad 4 didn't do that before upgrading to ios 7. Any advice besides hard reset or resetting settings? I really don't want to try a " setup as new devi

  • J2SE Adapter Engine

    Hello Everyone, I've got a little problem. I must cover the requirement that a file adapter exactly runs each night at 2 a.m. But the "polling mechanism" only allows to say that the adapter runs each 24 hours. Any suggestions how to solve this proble

  • Direct procurment indicator in production order

    hi I found in a production order, there is a "1" maintained under "direct procurment indicator " which means "external procurment" for an item, and a purchase requisition is generated for it.  And in CO02 I just can't remove it. I wanna know where do

  • Sound doesnt work

    how do i get the sound to work on the movies and music videos????