Satellite U200-10H - How to use 1600x900 screen resolution?

Hi to all.
I have a Toshiba Satellite U200 10H. Recently I have bought the monitor Samsung SyncMaster 2033 1600x900.
The graphic card does not support 1600x900 16/9. I insall alternative the driver([http://www.intel.com/support/ru/graphics/sb/cs-028366.htm]) of a graphic card (intel gma 945), but it has not helped. Now on toshiba 1440x900 necessary 1600x900. please Help!
Laptop characteristics; win XP professional
graphic card; intel gma 945
monitor; samsung 2033sw 1600x900

Hello
In worst case the screen resolution is not supported :(
But you could check the following:
Navigate to Display Properties Settings (right click on desktop > properties > settings). Then click on Advanced and select tab Monitor. *Uncheck* the box Hide modes that this monitor cannot display.
After this check the screen resolution for external monitor again.
I hope it helps! :)

Similar Messages

  • Satellite U200-122: How to use Pivot function on external Monitor?

    I have a Satellite U200-122, would like to use the external monitor in pivbot function.
    But I do not find where I can have the display rotate, so that it will be displayed in portrait format on the external monitor and accept resolution 1024x1280.
    Any ideas?
    Graphic driver: Intel Chipset 945GM express
    Thanks
    Isabel

    Thax for the tipp, but:
    That is exactly my problem: the intel graphics acceklerator DOES NOT offer any rotate functionality! I wonder why because I have read in many forums that it should have, I know it can be seen on the right part of the intel graphics accelerator window, but nothing is there.
    So i wonder, if in the U200 there is possibly a different graphic driver or management sofwtare, which just does not support this? Could it be that a graphic driver does not offer pivot???
    Shortcuts do not work either.
    Btw: when i put the laptop on a kensington workstation, then the kensington graphic manager -display -link - is used, and then with many workarounds i do get the monitor to show pivot in necessary reolution. but i want a to use a pivot monitor also at home without dockingstation...

  • HOW TO USE SELECTION SCREEN

    HOW TO USE SELECTION SCREEN
    I WANT TO INSERT PURCHASE DOCUMENT NUMBER
    AND WANT TO SEE ALL INFORMATION FOR THAT PURCHASE DOCUMNET NUMBER.
    THANKS IN ADVANCED.

    The main use of the selection-screen is to select screen in the back ground
    ex :    
    TABNAME
    IN THE ABOVE FIGURE  TABNAME IS THE FIELD AND THE BACK END IS   CREATED SCREEN IN THE BACK END
    THIS SCREEN CREATION WE CAN USED THE SCREEN SELECTION

  • How to use 'several screen function' used to be in os x 10.6

    hi ! ^^
    how r u ? good !
    how to use 'several screen function' used to be in os x 10.6 ??
    it was possible to change whole screen with 'command + arrow keys' (option + arrow keys maybe ??)
    but, in os x 10.7, it seems it is not possible. and instread of it 'mission controls' that is not uesful ..
    no windows drive direct access. no several screen function. crash when control panel ask me administration right.
    os x 10.5 or 10.4 was much easy to control.  
    plz fix and add good functions of 10.6 , remove good functions is not called 'upgrade'.

    You can still do it with CONTROL + Arrow keys, the same as 10.6
    Regards,
    Captfred

  • Satellite U200-10H - Need schematic for sound card

    Need schematic soundcard for Satellite U200-10H.
    Microfone power no work, there was a short circuit or an electrostatics.

    Hi
    I think you will not find a schematic for the sound card or your notebook. I never saw such technical manuals on the Toshiba website and I think they are not for public and only for the authorized service providers.
    If you have a hardware issue you should contact the nearest ASP:
    http://eu.computers.toshiba-europe.com => Support & Downloads => Find an authorized service provider
    I have only good experience with my ASP. The technicians are very friendly and do the work as fast as possible. :)

  • How to use split screen on a mac like on windows 7

    how to use split screen on a mac like on windows 7

    It does not function the same as windows, in that it does not have an automatic snap function.  You can put multiple apps up side by side though.  You might want to consider using Spaces instead.

  • How we will maintain screen resolution for tmaintaining able control in BDC

    how we will maintain screen resolution for tmaintaining able control in BDC. can you give the code or how we have to set it

    Hi,
    You need to use the CTU_PARAM options with the call transaction method.This is used if you would like to do a commit work once call trnasaction is done. This has also got very important property, for example if your Screen resolution is different from others then the screen (Application) will be different that is you'll be having say 5 lines in your screen where as your friend will be having 8 or 10 so your program might fail in this case. If you set variable DEFSIZE as 'X' it will always use the default screen size and hence avoids error.
    Use CALL TRANSACTION 'XXX' OPTIONS FROM w_ctu_params.( type CTU_PARAMS)
    This structure contains the follwing.
    DISMODE : Display mode (like the MODE addition)
    UPDMODE: Update mode (like the UPDATE addition)
    CATTMODE: CATT mode (controls a CATT)
    CATT mode can have the following values:
    ' ' No CATT active
    'N' CATT without single-screen control
    'A' CATT with single-screen control
    DEFSIZE : Use default window size (Here we are handling those transaction by giving default window size)
    RACOMMIT: Do not end transaction at COMMIT WORK
    NOBINPT : No batch input mode (that is, SY-BINPT = SPACE)
    NOBIEND : No batch input mode after the end of BDC data.
    The components DEFSIZE , RACOMMIT, NOBINPT, and NOBIEND always take the following values:
    'X' Yes
    This might help u in better understanding...
    Re: regarding bdc
    Re: ctu_params
    Regards
    Sudheer

  • Qosmio X500 - How to increase the screen resolution?

    Hi,
    Does anybody know how to increase the screen resolution? My qosmio X500 is 1920 x 1080 and I want to raise it to 1920 x 1200.
    Thank you/Red

    Hey
    1) I think the screen brightness is about 180 nits for this qosmio model. If I change the graphics card, can I increase the brightness to 300 NITS levels? If yes, which card do you suggest? If not, how can I achieve this?
    2) When I view the screen in 100 % magnitude, then the texts are too small to read. But then when I view the screen in 125 % or higher, then the texts go blurry. Is there a way to avoid this?

  • How to use Print Screen function (part deux)?

    The previous thread for the Print Screen function has been marked as read only, and won't allow any replies. I tried all of the suggestions (PrtScr, CTRL + C + PrtScr, etc.) and then CTRL V into MS Paint, but Print Screen still doesn't work on my machine.
    I'm running Win 7 on a HP Pavilion laptop cv7-6b32us. I suspect there's a switch somewhere in Win 7 or HP that allows the key to be turned off. I know of this because my previous employer did not want anyone doing print screens due to HIPAA violations. Thus, the functionality was turned off. Those of us in I.T. were provided a third-party software that aloowed us to do the same function, but it was not released to the physicians or nursing staff. If I have to, I'll go out and buy the software. I really need this functionality for a class I'm taking.
    Thanks!
    This question was solved.
    View Solution.

    Kurt, welcome to the forum.
    Here is a video to show you how to use the Snipping Tool:
    Please click the "Thumbs Up+ button" if I have helped you and click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • How to use Print Screen function?

    I've seen various descriptions of how to use the print screen function.
    It would be nice to actually be told one that works.  None have worked for me.
    [Fn] and Prt SCr does not work.
    Ctrl and Prt SCr does not work.
    Ctrl, Alt, and Prt SCr does not work.
    [Fn], Ctrl, and Prt SCr does not work.
    If anyone knows the correct method of activating the print screen function that would be good.
    From the looks of things HP has a big problem with this function.
    This question was solved.
    View Solution.

    On my notebook, the Insert key and the prt sc key are the same key, but the prt sc has a ring, around it, if you know what I mean.
    On the bottom left of my keyboard is a key that has fn with a ring around it, or I guess you could say it is in a little box.  By the way, there are a number of keys that have two functions on them, and to activate the second function, you must press the fn key at the same time as the desired function on the key.  In this case press the  fn key and  the prt scr key, and that puts an image of the screen on the clip board and then it can be pasted into Word or where ever.
    Here is somethine else you might like, if you can get it to work as I described above.
    To print only the active window, and not the entire desktop or the entire screen, you can do that by pressing the alt and prt sc at the same time.  Then it only captures to the clip board the window, and not the entire desktop. Oh, and in the scenario with the fn key, it has to be pressed also, so actually it's pressing the fn and alt and print screen all at once.
    I just performed each of the instructions above, and they worked well on my EliteBook 8440. 
    Hopefully you have the same experience,
    GeorgeFN
    GeorgeFN
    I work on behalf of HP.

  • How to use multiple screens?

    I have a two screen setup with my MBP.  If I full screen when watching a video using VLC, the other screen goes black... like in previous version of OSX.  How do I full screen while being able to use the other screen?

    M e too. Somehow I stumbled upon the right way to get it - inside iTunes AFTER updating iTunes and iTouch to latest versions.
    Now that I did that - some of my iTunes library locations were lost!!!!!
    Podcast video will not play in iTunes.
    And for some reason my iTouch can't get synced with podcasts.
    I wish Apple could get 1 of these major updates right the 1st time.

  • How to use dummy screen of Prgm SAPLCHRG

    Hi all,
       I have a dummy screen 2999 in program SAPLCHRG, please let me know how can i use this screen for adding some fields.
    Regards
    Taranam

    veer wrote:
    Hello Gurus,
    I have heard abt the Dummy Fact table and Cartaision join in OBIEE ...
    and we have one situation also where user needs to see all possible rows for report even if it's balnk..
    Can someone please suggest me some blog or use of dummy fact table to overcome such issue.??Here are two ways you can achieve what you are looking for:
    1) This is one way to do it and the way I discovered before learning the second way. The benefit of this way is that it is easier to maintain. Try it and see if this works for you.
    Re: Section Values showing NULL in Pivot
    2) The second way gets your report exactly how you want it to look and I have used this method as well. The downside to this (in 10g) is that making changes to the report is not that easy. You'll discover what I mean if you apply this method.
    http://gerardnico.com/wiki/dat/obiee/multiple_subject_area
    Good luck.

  • How to use a screen-field when applying BADI or User Exit to a T Code

    Hi Experts,
    I need your help on this problem.
    I have created a BADI for the transaction code miro. I have got the Exit name on which the enhancement has to be done. I want to perform a check on a text field (Scrren field name INVFO-SGTXT).
    When my break point occurs i enter INVFO-SGTXT in the field to check the value present in it. But it shows that no such field exists.
    My Basic doubt is how to use a value entered in a text field in a tcode while performing a User Exit or BADI on it.
    Do I have to declare it. If yes please mention how?
    Thanks in advance guys.

    Hi,
    The first question here would be... do you plan on having multiple implementations down the road because if not there really isn't any reason to create a BADI inside the exit.  If that is the case then add the field as an importing parameter in your BADI interface and then you should be able to see it inside the BADI at your break-point.
    Regards,
    Ryan Crosby

  • How to use Green Screen option?

    Sorry this is such a general question, but I have very limited internet access here at work (can't even access Google) and I would like to figure this out before I leave for the day so I can grab what I need on the way home.
    We are making weekly comical "newscast" type videos, and we have been using PhotoBooth to make it look like we are in a news room.
    I would like to stop using PhotoBooth (due to the obvious extreme limitations in video/audio quality) and use the green screen option in iMovie 09.
    Would anybody be so kind as to give a brief couple of paragraphs on the best way to accomplish this?
    I have seen the option pop up when inserting a clip on top of another, but which one is the footage/image to replace the green area... the original clip or the overlayed clip?
    And is there a specific shade/type of green that works best? Or can I just pick up a dozen yards of general "crayola" green fabric to cover a wall?

    I have tried but haven't had much luck. Although I am having a problem with Snow Leopard and iMovie right now. That may be affecting my success. Here are the instructions out of iMovie help.
    To use green-screen effects to superimpose video:
    Record video in front of a solid green backdrop, and then import it into iMovie.
    When you record, for best results do the following:
    Use a pure (highly saturated) color of green for the backdrop.
    The best color of green to use is often called “chroma key green” in paint and cloth.
    Make sure the subject doesn’t have any green clothing, and don’t include anything green in the shot, other than the backdrop.
    If possible, use multiple lighting sources to eliminate shadows on the subject being recorded.
    Include a moment at the end of the recording with the subject out of the frame. This indicates to iMovie what should be left out when the video is superimposed.
    Choose iMovie > Preferences, click General, and then make sure Show Advanced Tools is selected.
    In the Event Browser, select video that you recorded in front of the green backdrop.
    Drag the selection directly over a clip in your project (video, solid color, or animated background clip), and release the mouse button when the cursor displays a green plus sign .
    Choose Green Screen from the list of options that appears.
    The green-screen clip appears with a green border around it above the video clip in your project. You can drag it to a different spot to reposition it, or drag the ends to lengthen or shorten it.
    To more effectively mask areas of the green-screen clip, select the clip in your project, in the viewer click Cropped, and then drag the handles at the top of the viewer to more tightly enclose the subject of the video.
    Anything outside the highlighted area in the green-screen clip is removed from the picture. Be sure not to crop out areas that the subject moves into at any point during the green-screen clip.
    To produce a better-quality effect, double-click the green-screen clip in your project to open the inspector, then select “Subtract last frame.” iMovie uses information in the last frame to determine what to subtract from the finished clip.
    Selecting “Subtract last frame” works only if you included a moment at the end of the green-screen footage with the subject completely out of the frame.
    To watch the clip, click the Play Clip button in the viewer.

  • How to set Dynamic screen resolution in flex..?

    Hi All.,
    I am developing a flex application in adobe flex4. to set the application height is 100% width is 100% and using <flexmdi:MDICanvas> to set the height 780 ,so application get displayed on normal window correctly., But i try to press f11 key the screen size is expanded at the time application size is set exactly, MdiCanvass size is  not expanding on screen resolution.
    My question is how can I make sure that the application should look uniform across different platform/different browsers and different monitors to display screen resolution auto adjust in mdi canvass also.
    With Regards.,
    LinFlex-

    Hi,
    Use the below syntax...
    CALL TRANSACTION tcode... OPTIONS FROM opt
    ... OPTIONS FROM opt
    Effect
    Allows you to control processing using the values of the componetns of the structure opt, which must have the ABAP Dictionary type CTU_PARAMS. The components have the following meanings:
    DISMODE
    Display mode (like the MODE addition)
    UPDMODE
    Update mode (like the UPDATE addition)
    CATTMODE
    CATT mode (controls a CATT)
    CATT mode can have the following values:
    ' ' No CATT active
    'N' CATT without single-screen control
    'A' CATT with single-screen control
    DEFSIZE
    Use default window size
    RACOMMIT
    Do not end transaction at COMMIT WORK
    NOBINPT
    No batch input mode (that is, SY-BINPT = SPACE)
    NOBIEND
    No batch input mode after the end of BDC data.
    The components DEFSIZE , RACOMMIT, NOBINPT, and NOBIEND always take the following values:
    'X' Yes
    ' ' No
    If you do not use the OPTIONS FROM addition, the following control parameter settings apply:
    DISMODE
    From addition MODE
    UPDMODE
    From addition UPDATE
    CATTMODE
    No CATT active
    DEFSIZE
    Do not use default window size
    RACOMMIT
    Successful end on COMMIT WORK
    NOBINPT
    Batch input mode active ( SY-BINPT = X
    NOBIEND
    Batch input mode remains active after the BDC data
    Jogdand M B

Maybe you are looking for