Satellite U305 - New Intel drivers are not validated

I have a problem installing newest graphic drivers for Intel 965 express. Everytime I get a message that the driver being installed is not validated for this computer.
I got my drivers directly from Intel site because those are the newest ones (Toshiba site gives 2007 drivers only) but they does not work.
It looks like somehow Toshiba is blocking this driver for some reason but I don't know why
Computer:
Toshiba Satellite U305
Windows Vista Home Premium installed (32-bit)

Hi!
I had the same issue on my Satellite U400 notebook. I have solved this issue on this way:
Before I installed the new driver I have removed the old version. You should find it in control panel > Add/Remove programs. Then restart your notebook.
After restarting you will get the same error message I think but then you can install the driver manual. Therefore go in device manager and select the graphic card. Click on update driver and use the advanced installation. In the next windows choose the driver directory yourself.
After restarting the notebook the new driver should be installed.
Greets

Similar Messages

"The new table link contain TargetFieldNames that are not valid?

I am designing a report based on a sql stored procedure with 3 parameters required. I have a parameter that I would like to make dynamic based on an "Item" table for multiple selections.
I keep getting this error when I run the report
Prompting failed with the following error message: 'List of VAlues failure: fail to get values. (Cause of error: the new table link contains TargetFieldNames that are not valid. Error source: prompt.dll
Error code: 0x8004380d
Can someone point me to an example or tell me if this even possible to do?
Edited by: SHARON SCHMIDT on Feb 17, 2009 3:16 PM

Hi Sharon,
Searching for the error message got many KBase but I hope referring to the following would help you:
1211133 - Using parameters to select one, some or all values in a record selection formula
1220118 - Error: "List of Values failure"prompt.dll Error code: 0x8004380D"
Regards,
Sheeba

The Firewire drivers are not loaded

Hi,
The title of this post says it all.
When using system profiler I get the message " The Firewire drivers are not loaded " in red letters.
The Mac is a 2Ghz intel. So far I have...
1. Done all the usual maintenance. Erased the internal drive and re-installed the operating system. Re-set the PRAM. Re-erased and re-installed the operating system.
2. Discovered that the disks that came with the machine ( purchased brand new from Apple ) will not allow me to complete a hardware test - It hangs.
3. Wondered about being in the wrong job!
This all points, to me at least, to a faulty logic board. If it points some one else in a different direction I would love to hear about it
Regards
Ian

Hi Ian
You might try resetting your FireWire ports, scroll down to the section: +If the issue persists, try these steps:+ in the following article:
http://support.apple.com/kb/HT1317?viewlocale=en_US
Not sure why the Hardware Test would hang, maybe give it a try again:
http://support.apple.com/kb/HT1509
Dennis

Ssrs 2008 r2 error-Forward pointing dependencies are not valid

In an existing SSRS 2008 r2, report, I am attempting to add a parameter called 'Customer_Category'. I am getting the following error message:
The report paramter 'CustomerNumber' has a DefaultValue or a ValidVaue that depends on the report parameter 'Customer_Category'. Forward pointing dependencies are not valid.
I am trying to determine how to fix this error. The 'CustomerNumber' is a parameter value that is obtained by reading from a dataset. In this dataset there are existing other parameters called 'Customer_Type' and 'Customer_Preference'. Both of these parameters
obtain there values from selections that the user makes when the SSRS report is executing. There are no default values.
I am trying to have the 'Customer_Category' be the same way where there are no default values and the user must select the parameter value when the report is executing. There should only be one value that the user can select from.
The new parameter called 'Customer_Category' is the last parameter in the list of parameters. Does the order of parameters make a difference? If so, how can I move the 'Customer_Category' parameter in front of the customer_number parameter?
Here is the sql that is used from obtaining a list of customers from the dataset for customer_number:
SELECT   Distinct CustomerNumber
FROM   BridgeUserCustomer
WHERE
         Type = @Customer_Type
AND Preference = @Customer_Preference and Category = @Customer_Category
GROUP BY CustomerNumber
Would you tell me what is wrong and what I can do to solve the problem?

Create independent datasets for each parameter and try once.
Regards, RSingh

Import oracle.apps.fnd.framework.OAViewObject; are not valid.

Hi,
The requirement is to limit the results of a query of a search page(iprocurement --> Requisitions)by adding a hard coded condition to a where clause(CREATED_BY LIKE ('%LUMWANA%')).
The limitation,I have is that I am allowed to extend only the controller.So I can not write a service method in application module and append to the where clause.
The OAF developer's guide suggests that the only import from model I can have in controller is OAApplicationModule.
Imports like import oracle.apps.fnd.framework.OAViewObject; are not valid.
So I can not get the ViewObject in the controller and add new viewcriteria to it.
What are the options that I have with this requirement.Are there any options to get the default view criteria from OAQueryBean and add additional criteria rows to it on page load/On press of GO button in the controller itself.

hi,
In your Controller try the below:
import oracle.apps.fnd.framework.OAViewObject;
OAApplicationModule am = (OAApplicationModule)pageContext.getApplicationModule(webBean);
//String s1 = (String)oapagecontext.getTransactionValue("VoName"); ---you can try it if the below one will not work
OAViewObject cusVO= (OAViewObject)am.findViewObject(VOName);
cusVO.setWhereClause(null);
      cusVO.setWhereClauseParams(null);
      cusVO.setWhereClause("REQUISITION_HEADER_ID = :1");
      cusVO.setWhereClauseParam(0, reqNum);
      cusVO.setMaxFetchSize(-1);
      cusVO.executeQuery();
For more info, refer the below link:
https://forums.oracle.com/thread/620451?start=0&tstart=0
Regards
Mahesh

My usb port drivers are not working

i have purchaced new hp sleekbook os-win8, but after few days the usb drivers are not working what shoud i do
This question was solved.
View Solution.

What did you plug into the usb port.
Have your tried multiple devices?
When was the last time they worked?
Try removing the drivers in device manager.
Then reboot and let them reinstall
If that fails the try a System Restore to previous date when they did work.
Here is how to do a System Restore
http://www.youtube.com/watch?v=CsY_FnyJzdo
**Click the KUDOS star on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
**Click the KUDOS star on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Entitlements are not valid valid on compiled app

I just started using flash cs5 today to try and make a quick app, I have joined apples iphone dev program, I have a cert, and finally figured out how to get a .p12 file (i just dragged it into itunes). I create an ad hoc file and double click it and it goes into itunes just fine but when I sync my iphone it loads the app on the phone and at the end I get a message saying that it cant use the app because the entitlements are not valid valid. What am I missing? I am using windows 7 and not a mac, so alot of this stuff is very new. Has anyone else encountered this problem? Any ideas why its not working?

I faced the same problem, and you probably didn't type the application name in the provisioning profile field in the flash cs5 compiler.
For example; when you open the flash cs5 compiler, in the deployment tab you have to browse for your provisioning profile and the compiler will automatically type in the field right below the browsing field the following: (com.talalmanaa) - where talalmanaa can be any name you set in apple developer program while you create a provisioning profile - this is not sufficient coz you need to add the application name after talalmanaa. Hence, you should add your application name to be as the following:
com.talalmanaa.myAppName
P.S: you need to make sure that your provisioning profile can accept any application name (for testing) and that's by adding (*) sign before you create prov profile in your Apple's Developer program. so make sure that you type the following before you submit to create a profile:
com.talalmanaa.* (this start sign means that your provisioning profile can test any application name).

Some Of The Following Drivers Are Not Being Inslled On The Notebook

As the topic says, i have an Envy 6 1002TX laptop and in this laptop some of the drivers are not being installed while they are available in the download lists of drivers for the same laptop.
Product Number::B4P24PA#ACJ
OS::Windows 7 Ultimate x64
Here are thelist of Drivers that aren't working:-
1.Intel Smart Connect.
2.Intel turbo Boost.
and the Chipset drivers installation has readme file and installation instructions missing, see this:-

Hi
Please find the link given below might help you to fix your issue. Download both driver chipset and have it checked.
Intel Turbo Boost Technology Driver
Driver Chipset
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

My Ipod touch Is stuck in restoe mode. I have reinstalled Itunes 10.4 .1 10. windows says drivers are not installed. I have followed all trouble shooting advice, fixes and updates for windows 7

I have reinstalled Itunes 10.4 .1 10. windows says drivers are not installed. I have followed all trouble shooting advice, fixes and updates for windows 7

I have reinstalled Itunes 10.4 .1 10. windows says drivers are not installed. I have followed all trouble shooting advice, fixes and updates for windows 7

"Entitlements are not valid" error message when trying to sync ipa file from iTunes to iPad

Is anyone else getting this error message, "Entitlements are not valid", when trying to sync .ipa file from iTunes to iPad?
The issue I'm having is getting the ipa file that was built by the 'Adobe Flash Packager for Iphone' installed into my iPad.
So, I have a swf file that works and was able to publish it into the Android Market. I then compiled and build the same flash project with the Packager for Iphone into an .ipa file. But when I try and install this .ipa file into my iPad to do my testings, i'm getting the error message.
I would like to test my ipa file in my iPad device before submitting it to the Apple Store.
Any help would be appreciated. thank you.

Developing for iphone can be amazingly complicated and frustrating. (even before you start coding). The process of having to create a Certificate, to approving the Certificate, to Assigning the deviceIDs to the certificate, to creating the AppIDs, to creating the provisioning profiles and then creating the .p12 file... is just too tedious.
I solved the problem of the "Entitlements are not valid". The AppID i had set in the iPhone Developer Portal did not match that of the AppID i had set in the Adobe Flash CS5 -> Publish Settings. (ie. com.yourdomainname.yourappname). After I re-entered my AppID and compile, i was able to sync the .ipa file into my ipad.
I wish the error message had been a little more descriptive. Could have saved me a whole day.
I hope this helps others. But my guess is, if you don't set the 40 character device ID correctly, or the email in the signingcertificate correctly, you'll get this same generic error message.

Assistance with Error - virtualmachinemanager.psd1 module cannot be imported, one or more members are not valid.

Hello,
We use Orchestrator, System Center 2012 version 7.1.3022.0. I have an orchestrator script that reads through a txt file to find unresponsive virtual machines (Windows 2000 VM's cannot have the SCOM agent installed on them) so we can restart any
machines that are not responding.
The step to Get Computer/IP Status runs successfully in that it reports which VM's are running and which are not running. The next step then is to run a Powershell script that restart the VM's that are down. Here is my Powershell Script:
$ErrorActionPreference = "Stop"
try
Import-Module 'C:\Program Files\Microsoft System Center 2012\Virtual Machine Manager\bin\psmodules\virtualmachinemanager'
Get-VMMServer -ComputerName mlivsmsscvmm
# get vm object
$vm = get-SCVirtualMachine | where { $_.ComputerName -eq "\`d.T.~Ed/{A255D4D8-BD4D-4FF4-9A51-B1ABA82720B9}.Computer-name\`d.T.~Ed/" }
# save data to publish for future activities
$OrigVMMStatus = $vm.StatusString;
$AlertAdded = "\`d.T.~Ed/{A4B4EC8A-E4F8-40AB-9897-6906EAE139AE}.TimeAdded\`d.T.~Ed/";
$VMName = $vm.Name;
# we are at this point because the VM is not responding.
# Start VM - if VM status is "Running" then Stop the VM first
if($vm.StatusString -eq "Running")
{ Stop-SCVirtualMachine -vm $vm -force };
Start-Sleep -s 20;
if($vm.StatusString -eq "Stopped")
{ Start-SCVirtualMachine -vm $vm
$VMrestart = "Yes"
catch
Throw $_.Exception
Upon running the Powershell script I receive the following error in Orchestrator Log histry:
The 'C:\Program Files\Microsoft System Center 2012\Virtual Machine Manager\bin\psmodules\virtualmachinemanager\virtualmachinemanager.psd1' module cannot be
imported because its manifest contains one or more members that are not valid.
This script used to run without errors and nothing has been upgraded in our environment with regards to Orchestrator, VMM, SCOM. How would I find the 'one or more members' that is causing my issue?
Thank you.

Hi,
the thing is that PowerhShell in the "Run .Net Activity" is version 2.0 (http://www.sc-orchestrator.eu/index.php/scoblog/102-running-powershell-30-with-the-run-net-script-activity)
So, try your script embedded in PowerShell {}
Regards,
Stefan
www.sc-orchestrator.eu ,
Blog sc-orchestrator.eu

The parameters supplied for the batch are not valid.

Error:The parameters supplied for the batch are not valid
Stored Procedure is as follows
CREATE PROCEDURE [dbo].[Usp_TrackVehicleDetails]
@reg_Number NVARCHAR(25)
AS
BEGIN
SET NOCOUNT ON;
DECLARE @Imei_Number NVARCHAR(25),
@Imei_Table
NVARCHAR(MAX),
@Latitude_Val
NVARCHAR(MAX),
@Longitude_Val NVARCHAR(MAX),
@Imei_PK
NVARCHAR(MAX),
@result INT
-- Tracking Device by means of Latitude and Longitude
SELECT @Imei_Number=Imei_No FROM MapDevice_Vehicle WHERE Vehicle_No=@reg_Number;
SELECT @Imei_Table='Imei_'+@Imei_Number
SET @Imei_PK='SELECT(MAX(CAST(Imei_Id AS NVARCHAR(MAX)))) FROM dbo.'+@Imei_Table;
SET @Latitude_Val='SELECT Latitude FROM dbo.' +@Imei_Table+' WHERE CAST(Imei_Id AS NVARCHAR(MAX))='+'('+@Imei_PK+')';
SET @Longitude_Val='SELECT Longitude FROM dbo.' +@Imei_Table+' WHERE CAST(Imei_Id AS NVARCHAR(MAX))='+'('+@Imei_PK+')';
EXEC @result= sp_executesql @Imei_PK,@Latitude_Val,@Longitude_Val
SELECT @result
--RETURN @result
BEGIN TRY
BEGIN TRANSACTION T1
-- Returning Values based on Vehicle_Number
SELECT ISNULL(@Latitude_Val,'')[latitude],
ISNULL(@Longitude_Val,'')[longitude]
IF @@ERROR!=0
BEGIN
ROLLBACK TRANSACTION T1
END
ELSE
COMMIT TRANSACTION T1
END TRY
BEGIN CATCH
SELECT ERROR_MESSAGE() AS ErrMsg, ERROR_LINE() AS ErrLine,ERROR_PROCEDURE() AS ErrProc
END CATCH
END

Your construct is not correct....
EXEC @result= sp_executesql @Imei_PK,@Latitude_Val,@Longitude_Val --These
should be parameters/....
Please try the below(The longitude and latitude to be included...)
/*Test script*/create table MapDevice_Vehicle(vehicle_no nvarchar(25),imei_no nvarchar(25))
Insert into MapDevice_Vehicle Select 'KL8P8234','KL'
create table Imei_KL(Imei_Id nvarchar(25))
Insert into Imei_KL Select 'KL8P8234'
exec [Usp_TrackVehicleDetails] 'KL8P8234'/*Test script*/
CREATE PROCEDURE [dbo].[Usp_TrackVehicleDetails]
@reg_Number NVARCHAR(25)
AS
BEGIN
SET NOCOUNT ON;
DECLARE @Imei_Number NVARCHAR(25),
@Imei_Table NVARCHAR(MAX),
@Latitude_Val NVARCHAR(MAX),
@Longitude_Val NVARCHAR(MAX),
@Imei_PK NVARCHAR(MAX),@paramdefs nvarchar(MAX),@result INT
-- Tracking Device by means of Latitude and Longitude
SELECT @Imei_Number=Imei_No FROM MapDevice_Vehicle WHERE Vehicle_No=@reg_Number;
SELECT @Imei_Table='Imei_'+@Imei_Number
SET @Imei_PK='SELECT(MAX(CAST(Imei_Id AS NVARCHAR(MAX)))) FROM dbo.+@Imei_Table';
SET @paramdefs = N'@Imei_Table nvarchar(255)';
--SET @Latitude_Val='SELECT Latitude FROM dbo.' +@Imei_Table+' WHERE CAST(Imei_Id AS NVARCHAR(MAX))='+'('+@Imei_PK+')';
--SET @Longitude_Val='SELECT Longitude FROM dbo.' +@Imei_Table+' WHERE CAST(Imei_Id AS NVARCHAR(MAX))='+'('+@Imei_PK+')';
EXEC @result= sp_executesql @Imei_PK,@paramdefs,@Imei_Table = @Imei_Table
SELECT @result
--RETURN @result
BEGIN TRY
BEGIN TRANSACTION T1
-- Returning Values based on Vehicle_Number
SELECT ISNULL(@Latitude_Val,'')[latitude],
ISNULL(@Longitude_Val,'')[longitude]
IF @@ERROR!=0
BEGIN
ROLLBACK TRANSACTION T1
END
ELSE
COMMIT TRANSACTION T1
END TRY
BEGIN CATCH
SELECT ERROR_MESSAGE() AS ErrMsg, ERROR_LINE() AS ErrLine,ERROR_PROCEDURE() AS ErrProc
END CATCH
END

Report parameter startdate has a defaultvalue or a valid value that depends on the report parameter startdate forward dependencies are not valid

Hi,
Am trying to develop a report the parameter has an issue, it gives me an error.
There are 2 parameter (1st is Date range like start and end date and 2nd is Loan number)
When ever I select date range the Loan number parameter should go blank. If I input a loan number then date range should go blank.
What should I do. Please help
ERROR --report parameter startdate has a defaultvalue or a valid value that depends on the report parameter startdate forward dependencies are not valid

Hi Kay_MD,
If there are only two parameters, we can use first parameter charge the second one, but the second one cannot charge the first one in turn. Because parameter forward dependencies are not valid. To achieve your requirement, we can create another parameter
to control Date_range and Loan_number parameters. For more details, please see:
Add a parameter named ReportParameter1 with two available values: Date_range and Loan_number.
Use the following expression as the default value in Date_range parameter:
=iif(Parameters!ReportParameter.Value="Date_range",1,"") (1 means a useless value)
Use the following expression as the default value in Loan_number parameter:
=iif(Parameters!ReportParameter.Value="Loan_number",1,"") (1 means a useless value)
Please note that the Date_range and Loan_number parameters should enable Allow blank value (“”), and the blank values should also be contained in available values.
If there are any other questions, please feel free to let me know.
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

Drivers are not working even after reinstalling in Hp 2000 series windows 8.1

Suddenly my audio drivers is disabled. It shows error to re install drivers , i did but still its not working... I have Hp 2000 series laptop windows 8.1 Kindly help

Hello @Noman2006,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how the audio drivers are not working on your notebook computer, and I would be happy to assist you in this matter!
To return the audio output to working order, i recommend re-installing the original software and hardware drivers on Using Recovery Manager to Restore Software and Drivers (Windows 8). To update these drivers, please follow this resource on Using HP Support Assistant (Windows 8).
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

FireWire drivers are not loaded

I've got a 14 month old 15" MacBook Pro, now running Leopard. Firewire has not been working for some time. I've now looked at the System Profiler and it is reporting the following against the FireWire entry:
Warning: The FireWire drivers are not loaded.
Does anyone know if it is possible to reinstall the drivers, and if so where do I download them from?
Many thanks,
Mark

My CrapBook Pro is doing the same thing. I have had problems with the Firewire 400/800 from the start...only recently did I really want them to work. It worked maybe 1 out of 20 times...multiple devices. ALL DEVICES WORKED WITH MY G5 running Tiger (was that before leopard).
So I brought the computer into the Genius Bar...they hooked some things view Firewire and they all showed up. I was told to bring one or more of my devices in to try them there...I get home...connect my WD HD with FW800...it appears...I connected my Plextor Burner with a movie in it...it appeared...I got excited that things might be working. Unplugged items plugged them in again...and nothing is showing up...I can still hook up the WD HD with USB...I know when I try the Western Digital HD via FW THE DRIVE KNOWS IT IS CONNECTED via lights...so I rebooted and tried it again...CRAP...nothing shows up via FW...then I too looked and found:
FireWire Bus:
Warning: The FireWire drivers are not loaded.
So...Apple is finally becoming as dependable as the PC! What a shame. Sounds like no one reading this forum has been able to get an answer.

Satellite U305 - New Intel drivers are not validated

Similar Messages

Maybe you are looking for