Satellite U840W PSU5XA - Win 8.1 installation and effective SSD usage

Hello.
Im hoping for a solution to two issues.
The second I suspect is caused by the first.
Satellite U840W PSU5XA-001006
Started to receive BSOD with various faults.
Most persistant was IRQ LESS or not EQUAL- iaStorAV.sys
Many hours of searching and I cannot locate a solution nor post that actually has the "AV" extension on on iaStore.sys.....
So, i factory resetted, and various other issues (BSOD's) persisted.
So, I Clean installed Windows 8.1 straight over everything and deleted all previous files.
I noticed the system was not running any factory TOSHIBA Branded utilities etc. and seemed to be a lot slower. I suspected that this was caused due to the 32GB SSD used for Cache had now seemingly been bi-passed and everything was now strictly running off the 500GB HDD. I dont recall BSOD's but the system was significantly slower on boot and performance.
Sooooo, (SIGH), I again reset back to factory settings and this gave me back TOSHIBA branded utilities such as service station and the like.
HOWEVER, The BSOD's remained and once upgrading to windows 8.1 KEEPING files and settings, the iaStorAV.sys error has returned (specifically when closing lid into sleep mode) forcing CRITICAL error and forcing system into reboot instead of awakening from sleep.
Note: Windows is a legit MS copy so that isnt the issue either. Even stranger is that the 8.1 instal had been running at least 8 months no issue prior to sudden BSOD Page file and iaStorAV errors. Readings and posts have me believing MS Updates to bee the culprit here for the beginning of these issues.
I read a similar post regarding enabling RAID CACHE PRIOR to Windows 8.1 install. My intuition tells me that these two may just be related. i.e. If windows has not installed RAID CACHE properly, then CACHE isnt being strored correctly and causing BSOD's. Im a newbie at this stuff, so be patient.....
What I really want to know is, How can I now Factory Reset Windows 8, making positive the 32GB is being used as CACHE and assisting fastboot etc, then safely upgrade to Windows 8.1?
Any assistance would be greatly appreciated.
THINGS ALSO ATTEMPTED: IRST and RAID re-Install, Memory Diagnostic (Passed), BIOS Upgrade to 6.70, Rapid Storage Drivers re-installed
Thanks ahead of time,
Mr Frustrated............

Ok, well, its been a while and no-one had really come up with a solid solution. But thank you JakieStewart for the RST information.
Note: Updating RST drivers alone, failed....
However, I have been able to work around the issue in a way:
I have lost the ability to use the SSD as a cache, which really annoys me, as all the reboots, and suggestions i have read, re-installs etc proved flawed in some way or another.
So, I have instead chosen to clean install windows 8.1 then followed a post relating to Diskpart and setting SSD hibernation partition.
A link to consider would be http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide.pdf
However i followed a somewhat abbreviated version.
Conclusion:
1. Now I can close the lid on my U840W (INTO SLEEP or HIBERNATION Mode and not get a "System Thread Exception iaStorAV.sys error because I have 1. Reluctantly Clean Installed Windows 8.1 over factory image and 2. now created a >Hibernation Partition< on the SSD
Even though SSD Cache may no longer be available, creating this Hibernation Partition assists with Rapid START Technology and the associated iaStorAV.sys type errors
You can find your Toshiba Rapid Store Technology Drivers for your model here:
https://downloadcenter.intel.com/search?keyword=Intel%C2%AE+Rapid+Storage+Technolog y+%28Intel%C2%AE+RST%29
2. I no longer have the option to use the SSD as a cache, but overall my system runs a lot better now
3. The SSD is not visible in explorer (which it never was under the original settings anyway)
3. Downside: I can no longer boot or reset back to original Toshiba factory settings and can only recover from the new recovery disk (USB) i have made.
I have now also downloaded and stored on a USB all the original TOSHIBA U840W Drivers from http://www.mytoshiba.com.au/support/computers/ultrabook/u840w/psu5xa-001006/download?os=30
If like me, you clean install windows 8.1 I highly suggest getting your drivers downloaded locally so that you don't have to keep going back to Toshiba or Intel unless updates are required.
4. Note: Make note to set the BIOS Hibernation mode to "Immediately" if you choose to go this route as per the instructions on the Intel Link
5. Change "Toshiba Power Options" to make sure that closing Lid send laptop into Sleep or Hibernation (Both work) Do this by searching for "power options' in windows charm search and >select power plan >Change power plan settings >Change Advanced Power Settings >Power Button and Lid >selecting either Sleep or Hibernation (both work as i said earlier)
ON THE PRO SIDE: My HDD boot from total Shutdown State time is "about" 50 seconds but more significantly, closing the lid into sleep keeps my work available again, and takes 9.5 seconds to boot from sleep into usable actions!!!!
So despite losing SSD Cache, I now know a lot more about my computer, and the sleep function and Hibernation work supremely well.
I hope someone finds this thread useful...
Shane
Laslty, it is sooooo strange how this all happened overnight with the iaStora.sys; iaStorAV.sys iaStora.sys errors...and how restoring back to previous states didn't work, and how it seemingly corrupted even the Flash Stored Cache settings and Operating System! At least I now understand my computer better and luckily this didn't occur during previous Diploma studies. Phew.....
Message was edited by: shaner1

Similar Messages

Satellite C660-1ZM Win 7 64bit: mousepad and USB - "code 52" driver error

Hello,
Having recently set up a new Satellite C660-1ZM running Windows 7 64bit (upgraded from Home Premium to Ultimate) for a friend, the mousepad and USB ports have suddenly stopped working. The drivers show an exclamation mark against them and the error is "code 52" which is related to driver signing. Windows doesn't seem to recognise the driver signatures for the published drivers that came on the machine's pre-installed disc, so the devices don't work. I've updated the drivers (Intel chipset [which includes USB]; Synaptics touchpad) to the latest ones publised on the Toshiba web site - and we have the same problem.
Pressing F8 on boot allows you to select "disable checking of driver signing" in the WIndows 7 boot options, which then enables the drivers and all is well, until you reboot - at which point you have to hit F8 again.
I think that one of the many recent Windows updates has somehow messed things up, but we can't easily prove that. The machine worked fine for a week or so, then the mousepad suddenly quit working around 8th August 2012.
1) Are there valid signed drivers that pass whatever checks Microsoft impose on driver signing, including whatever checks they've potentially just imposed via some recently inflicted update?
2) Does anyone know exactly how to disable the checking of driver signing permanently, so that a reboot will not require the F8 keypress and so on?
Uninstalling the mousepad driver and rebooting gives the basic mouse functionality, without the Synaptics cleverness. However, the USB ports still don't work because their driver doesn't load, so an external mouse doesn't work.
It's an infernal nusiance. Driving the system off the keyboard to uninstall drivers etc. is not much fun.
Cheers, Colin.

Hi
Did you receive the error that windows cannot verify the digital signature for the drivers required for this device? Usually this means the error code 52
Since the USB drivers are parts of the Windows OS, I dont think that this could be an signature issue I think some files are damaged.
Try to uninstalling/reinstalling the driver and deleting the device and its drivers from device manager before reinstalling.
Usually this should help, if not, well try to repair the system.
Power up the unit and press F8. Then choose Repair my Computer.
Now choose the first option which would help to repair the system.

Satellite M100-126 - Win 7 32bit indicates "only" 3GB of usable memory

Hi,
Here's the situation:
I have a Toshiba satellite M100-126 (PSMA1E - 0PV021FR) running Windows 7 32bit.
It originally had 2gigs of Ram, but after my brother's laptop broke down (motherboard failure) I took his 2x2gig ram and installed them in my laptop.
At first, the BIOS only detected 3gig, so I flashed the bios using the one recommended by Toshiba Download center, i.e. v 3.0 , direct link http://support.toshiba-tro.de/tools/eula/calleula.asp?ID=66238 (if it works). There is also a version 5.6, only for Windows Vista, but I did not use that one.
So now, the bios detects 4gigs, and so does Windows, but windows indicates "only" 3gigs of usable memory.
In Windows resource allocation, 1gig is "hardware reserved", so it's 3gig usable memory. If I replace one of the 2gig modules by a 1gig module, I get only 2mb of hardware reserved, and the 3 installed gigs of memory are usable...
Here are the questions, now:
I am aware of the memory limit for 32bit systems, and that I won't be able to use the full 4gigs anyway, but my brother got 3.5 gigs of usable memory on his 32bit system... Is it

Thanks for the answer, 3.2gigs then, must have understood the little bro wrong.. :-)
Yet, under Windows, in resource allocation, the memory used by the video card is indicated as similar whether I install 4 or 3 gigs of memory...
Oh well, not a big loss, when I find the time I'll run benchmark tests with both installs and see if there's a difference.
Any idea on whether I'd gain anything with Win 7 64bits or would it just be wasted on a 3y old system (Windows indicates it's 64bit compatible)
Thanks!

Qosmio X70-A-12N - no sound over HDMI after Win 8.1 installation

Hallo,
I installed on my Qosmio Windows 8.1 and all driver.
Now I have a Problem with HDMI Sound.
When I connect with TV, I see the Picture on TV but don't get sound.
I go to Control Panel: Sounds and Multimedi and I see the internal devices (loudspeaker from Laptop and Headset).
I activated to see disconnected devices and no other devices will be displayed.
I assume, it fail a driver.
I installed Sound driver, DTS Studio Sound, Toshiba Audio Enhancement and SRS Premium Sound HD Plug-In.
I don't installed the regestry patch -> For what I need it?
Have you an idea to solve my problem?
THX
Richard
(Sorry for my bad english)

Hi
>I installed on my Qosmio Windows 8.1 and all driver.
As far as I know the Qosmio X70-A-12N were preinstalled with Windows 8.1 64bit system and this OS was configured by Toshiba.
Did you install new Windows 8.1 or did you use the Toshiba system?
Did you create recovery medium (recovery disk or USB flash memory stick)?
In case you create such recovery disk, I would recommend you to use it in order to set the system back to factory settings. This should fix your HDMI sound issue.
How about other Toshiba software installation like for example Toshiba system driver, display driver etc? Did you install all the Win 8.1 drivers and tools which were released for this unit?
Missing software could be main reason for your HDMI issue

Win 7 64 bit and SB Titanium X-FI Drivers

Ok - sound dissapeared yesterday, replaced by some silly High Definition Audio Device driver that doesn't work that well at all. Sound driver pack 2.7 and the latest Beta can't find the card. Tried compatibility mode and tried running as Administrator - no joy. Even tried rolling back a week in case it was a windows update that was the problem, and still no luck. Moved the card to another PCI-E slot - still no luck.
I don't care if it's creative or MS - this is poor - I just spent over a grand upgrading a gaming system I built for 3 grand 2 years ago and this isn't meeting my expectations. Card has worked in the previous rig well (apart from a few shoddy driver releases) and in the new rig it's been working fine for about 2 months until last week. Only system changes have been installing Resident Evil 5, Ghostbusters, L4D2, the new version of VLC and yesterday the latest NVidia driver - unconfirmed if the sound was working before that or not, but the microphone dropped off about a week prior.
For the time being i'm running back to onboard sound (yuk) awaiting direction, but i've been through the posts of the many people who have had the same problems and while running as administrator has worked for some of them - I note that as for myself, it hasn't worked for all of them.
Card unable to be detected via driver installer, auto-updater (admin, compat or otherwise - even the AutoUpdateA file)

-Re: Win 7 64 bit and SB Titanium X-FI Drivers? Sorry - no go - uninstalled the Creative apps and drivers again, uninstalled the MS High Definition Audio Device however it won't let me remove it's driver files (assuming as it's a nati've driver). Every time I uninstall it it wants to restart, every time I restart it's back again immediately. If I uninstall and don't restart, or even if I do, there's NO change to the MS Windows Update results even when forcing a recheck. I'm really stuck.
If I try to li've with the MS HDAD driver with the Li've Titanium in the PC, if I plug anything into the front, to doesn't detect it's there - if I place anything in the back same again. If I remove the headphones it seems ready to accept something? . It's all back to front.
The only time I could get the MS HDAD driver to do anything was with the onboard sound device turned on and the Titanium X-FI removed. Please note that no driver other than the MS HDAD has been loaded on the system for the onboard sound and it is definately turned off at this stage and during testing the X-FI.
I'm going to have a play in Safe Mode, but currently all roads lead to fail.

Apparent mismatch installer and coreinfo

I am attempting to upgrade Win 8.0 x64 to Windows 8.1 x64 (standard editions) using iso images downloaded with my product key. I checked processor hardware compatibility when installing 8.0 and all is fine with windows 8.0. But windows 8.1 won't
install. The installer claims that the CPU doesn't support PREFETCHW instruction and aborts.
However running "coreinfo" (sysinternals) tells me another story - that prefetchw and all other CPU prerequisites ARE INDEED met by my Pentium 4. Inclined to believe this as the 64 bit Windows 8.0 runs just fine. What gives?

Hi CHEN,
Thanks for your reply. I need to be more clear...
I wrote...
*The installer claims that the CPU doesn't support PREFETCHW instruction and aborts.*
This message did indeed come from an upgrade attempt from Windows 8.0 x64 standard edition (and I had just installed that fresh (as a clean install) from iso image that I downloaded from the windows store using the upgrade assistant. Your reply might indicate
that I have some mileage in trying this approach again AFTER installing critical & important updates and turning windows firewall off temporarily.
I also wrote..
*using iso images downloaded with my product key.*
I gave up on the upgrade route and downloaded iso images instead using the Media Creation Tool to USB ISO images of Windows 8.0 and Windows 8.1 Standard x64.
Windows 8.0 installs and runs just fine using clean install from USB ISO image.
WINDOWS 8.1 install consistently fails during installation...
The following error message is flashed on the screen (captured by video)
Your PC needs to restart.
Please hold down the power button:
Error Code: 0x000000C4
Parameters:
0x0000000000000091
0x000000000000000F
0xFFFFF80212FC0A00
0X0000000000000000
BIOS offers me control over hyperthreading on/off but the setting has no influence on this behaviour.
===========
Here is what coreinfo has to say about my CPU....
Coreinfo v3.31 - Dump information on system CPU and memory topology
Copyright (C) 2008-2014 Mark Russinovich
Sysinternals -
Intel(R) Pentium(R) 4 CPU 3.00GHz
x86 Family 15 Model 4 Stepping 9, GenuineIntel
Microcode signature: 00000003
HTT             *       Hyperthreading enabled
HYPERVISOR      -       Hypervisor is present
VMX             -       Supports Intel hardware-assisted virtualization
SVM             -       Supports AMD hardware-assisted virtualization
X64             *       Supports 64-bit mode
SMX             -       Supports Intel trusted execution
SKINIT          -       Supports AMD SKINIT
NX              *       Supports no-execute page protection
SMEP            -       Supports Supervisor Mode Execution Prevention
SMAP            -       Supports Supervisor Mode Access Prevention
PAGE1GB         -       Supports 1 GB large pages
PAE             *       Supports > 32-bit physical addresses
PAT             *       Supports Page Attribute Table
PSE             *       Supports 4 MB pages
PSE36           *       Supports > 32-bit address 4 MB pages
PGE             *       Supports global bit in page tables
SS              *       Supports bus snooping for cache operations
VME             *       Supports Virtual-8086 mode
RDWRFSGSBASE    -       Supports direct GS/FS base access
FPU             *       Implements i387 floating point instructions
MMX             *       Supports MMX instruction set
MMXEXT          -       Implements AMD MMX extensions
3DNOW           -       Supports 3DNow! instructions
3DNOWEXT        -       Supports 3DNow! extension instructions
SSE             *       Supports Streaming SIMD Extensions
SSE2            *       Supports Streaming SIMD Extensions 2
SSE3            *       Supports Streaming SIMD Extensions 3
SSSE3           -       Supports Supplemental SIMD Extensions 3
SSE4a           -       Supports Streaming SIMDR Extensions 4a
SSE4.1          -       Supports Streaming SIMD Extensions 4.1
SSE4.2          -       Supports Streaming SIMD Extensions 4.2
AES             -       Supports AES extensions
AVX             -       Supports AVX intruction extensions
FMA             -       Supports FMA extensions using YMM state
MSR             *       Implements RDMSR/WRMSR instructions
MTRR            *       Supports Memory Type Range Registers
XSAVE           -       Supports XSAVE/XRSTOR instructions
OSXSAVE         -       Supports XSETBV/XGETBV instructions
RDRAND          -       Supports RDRAND instruction
RDSEED          -       Supports RDSEED instruction
CMOV            *       Supports CMOVcc instruction
CLFSH           *       Supports CLFLUSH instruction
CX8             *       Supports compare and exchange 8-byte instructions
CX16            *       Supports CMPXCHG16B instruction
BMI1            -       Supports bit manipulation extensions 1
BMI2            -       Supports bit manipulation extensions 2
ADX             -       Supports ADCX/ADOX instructions
DCA             -       Supports prefetch from memory-mapped device
F16C            -       Supports half-precision instruction
FXSR            *       Supports FXSAVE/FXSTOR instructions
FFXSR           -       Supports optimized FXSAVE/FSRSTOR instruction
MONITOR         *       Supports MONITOR and MWAIT instructions
MOVBE           -       Supports MOVBE instruction
ERMSB           -       Supports Enhanced REP MOVSB/STOSB
PCLMULDQ        -       Supports PCLMULDQ instruction
POPCNT          -       Supports POPCNT instruction
LZCNT           -       Supports LZCNT instruction
SEP             *       Supports fast system call instructions
LAHF-SAHF       *       Supports LAHF/SAHF instructions in 64-bit mode
HLE             -       Supports Hardware Lock Elision instructions
RTM             -       Supports Restricted Transactional Memory instructions
DE              *       Supports I/O breakpoints including CR4.DE
DTES64          *       Can write history of 64-bit branch addresses
DS              *       Implements memory-resident debug buffer
DS-CPL          *       Supports Debug Store feature with CPL
PCID            -       Supports PCIDs and settable CR4.PCIDE
INVPCID         -       Supports INVPCID instruction
PDCM            -       Supports Performance Capabilities MSR
RDTSCP          -       Supports RDTSCP instruction
TSC             *       Supports RDTSC instruction
TSC-DEADLINE    -       Local APIC supports one-shot deadline timer
TSC-INVARIANT   -       TSC runs at constant rate
xTPR            *       Supports disabling task priority messages
EIST            -       Supports Enhanced Intel Speedstep
ACPI            *       Implements MSR for power management
TM              *       Implements thermal monitor circuitry
TM2             -       Implements Thermal Monitor 2 control
APIC            *       Implements software-accessible local APIC
x2APIC          -       Supports x2APIC
CNXT-ID         *       L1 data cache mode adaptive or BIOS
MCE             *       Supports Machine Check, INT18 and CR4.MCE
MCA             *       Implements Machine Check Architecture
PBE             *       Supports use of FERR#/PBE# pin
PSN             -       Implements 96-bit processor serial number
PREFETCHW       -       Supports PREFETCHW instruction
Maximum implemented CPUID leaves: 00000005 (Basic), 80000008 (Extended).
Logical to Physical Processor Map:
** Physical Processor 0 (Hyperthreaded)
Logical Processor to Socket Map:
** Socket 0
Logical Processor to NUMA Node Map:
** NUMA Node 0
No NUMA nodes.
Logical Processor to Cache Map:
** Data Cache          0, Level 1,   16 KB, Assoc   8, LineSize 64
** Unified Cache       0, Level 2,    1 MB, Assoc   8, LineSize 128
Logical Processor to Group Map:
** Group 0

Satellite U840W - Panel Open - Power On - unable to disable

I have a Satellite U840W - the display doesn't have a lock on close, so would power on in a laptop bag. I was able to disable this in the Toshiba System Settings tool.
However, a recent update means that even though the setting is Disabled, it will still power on when the lid is opened.
Any suggestions on how to stop this happening, or how to revert to a previous version of the utility that actually worked?

> This worked until I updated to the current Toshiba Utilities/Drivers.
>Anyone able to help reverting to the previous version?
In such case I would recommend you to set the system back to the early date.
To the point before you updated the utility.
1. You can do this easily. Point to the top-right corner of the screen, move the mouse pointer down, then click Search.
2. Enter Control Panel in the search box, and tap or click Control Panel.
3. Enter Recovery in the Control Panel search box, and then tap or click Recovery.
4. Tap or click Open System Restore, and then follow the instructions.

Satellite U840W - network LAN adapter just disappeared

I need to connect my laptop Satellite U840W via Ethernet and I can't find the LAN controller, everything was working fine but from one day to another it just disappeared.
I've been downloading the drivers many times but still nothing appears,
Any tips? Is it possible that the ethernet card might be broken?
Thank you

Hi
You mean the LAN controller isnt listed in device manager, not even as an Ethernet controller nor as an unknown device?
Hmm sounds like LAN controller malfunction. But this is really hard to believe
How about the BIOS?
Did you set it t default? Check this
However before talking with an service engineer, I would recommend you to reset the notebook back to factory settings just to check if the same LAN issue would appear using the Toshiba preinstalled image.

HT4623 Please help I I have updated pc win 8, update itunes and i can open and access all in icould but my reminders will not load error message can't load reminders

I can not open my reminders in icloud, error message can't load reminders. Have hp win 8 and all has been fine until today for over a year. win updates are done and itune updates done, what should I do?

Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased.
 Cheers, Tom

Problem with installation and activation

Hi, I have a problem with the installation of Adobe Muse.
I had a free 30-days trial, when it was over I bought the product ($ 13 per month),
I installed the program again and I see the same window with the finished Trials
and it requires a serial number and does not allow to enter the program.
I installed the program on your PC wife without any problems, but I can not install it on a laptop.
I have a laptop with Windows 8 operating system.
What I've done:
1. Uninstalled the free program,
2. check the connection to the Internet,
3. has installed a new program from the official website adobe.com,
4. Remove the line for the activation of the hosts file and resave the file,
5. turned off the brandmower,
6. rebooted.
I can't get support for a 3 days, is it the most terrible support I've ever seen? I dunno
Please help me at [email protected]

I guess this stuff helps me
http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html
2014-08-07 20:07 GMT+07:00 Дмитрий Броский <[email protected]>:
thanx
>
2014-08-07 18:18 GMT+07:00 Prabhakar.Kumar <[email protected]>:
problem with installation and activation created by Prabhakar.Kumar
>> <https://forums.adobe.com/people/Prabhakar.Kumar> in *Help with using
>> Adobe Muse CC* - View the full discussion
>> <https://forums.adobe.com/message/6619532#6619532>
>>

Installation and performance wonderful!

Just completed installation and testing of Aperture 3. 20K images, mostly RAW from Canon 40D and 5DM2 (11 to 23 MB RAW files), around 300GB.
Ran Consistency Check and then Rebuild on Aperture 2 libraries before starting move to Aperture 3.
Backed up Aperture 2 Libraries on several hard drives (belt and suspenders).
Installed from Ap 3 disk.
Did software updates re slideshows and new RAW update.
Turned off Faces (can run this later).
Did not reprocess files, just the update. I will reprocess as needed, when I want to use new tools on old files.
Update on both Mac Pro (2006, 2.66GHZ, 7GB ram) and MacBook Pro (2008, 2.5 GHZ, 4 GB ram). No other application slowed down at all during update. Update took about two hours on each machine.
Library and adjustments are very snappy.
Printing went exceedingly well, after re-entering my presets.
Image Browser shows Aperture library.
Not a single problem so far. I've spent almost a week reading the posts here and I've seen all the problems some people have had.
In my view, a very, very impressive new version.

I know it really probably will not help but I submitted a bug report.
"17-Feb-2010 12:16 PM Brian Hursey:
Summary:
Major issue with Aperture 3 when converting A2 library's and projects to A3.
Steps to Reproduce:
Senerio 1. Open an existing aperture library. It tells you you will need to convert the library conversion only gets to about 5%.
Senerio 2. Importing and not converting an existing A2 library into a A3 library.
Senerio 3. Reprocessing masters on a imported A2 project.
Expected Results:
Conversion, importing processing needs to keep from locking up the system and making it unusable.
Actual Results:
Uses all systems resources and creates a 43+ gig swap file. Used 100% of both cores of my 2.0 ghz 2009 mac mini, and used all of the ram.
Regression:
System: Spring 2009 Mac mini. 2.0 ghz core duo, 2 gigs of DDR3 ram, Snow Leopard 10.6.2 , Aperture 3.
Notes:
Possible work a rounds 32bit mode will test tonight. "

BO XI 3.1 installation and Upgrade activity Steps

Hi Experts,
Right now we are using BO XI R2 Version, Planning to uninstall XI R2 and do a fresh installation of BO XI 3.1 with SP3.
Do I need to install the Java latest version for XI 3.1? Right now we have the following setting,
         j2re1.4.2_04
         j2re1.4.2_16
         jre1.5.0_14
Since the up gradation of Reports, user, groups, universe events etc are from XI R2 version to XI 3.1.So Is it enough to
install BO XI 3.1 with SP 3, or do I have to go for FixPack inorder to avoid problem after this upgrade activity.
Could you please tell me about the BOXI R2 to XI 3.1 installation and Upgrade activity Steps.
Regards,
Sridharan

Hi,
you dont need a special JRE version on the Server. With the installation of BO a own JRE will be installed for BOE. Only for developing WebI reports the developer need a 1.6.x JRE later on.
There is already FixPack 3.1 out but installing "only" SP3 should be sufficient.
I would recommend you check the upgrade guide from Rel.2 to XI 3.1:
https://websmp208.sap-ag.de/~sapidb/011000358700001646952008E/xi3-1_bip_upgrade_en.pdf
You need a S-User to Login.
Regards
-Seb.

I installed elements 12 on a Win 8.1 computer and moved all my photos from my old XP machine. I updated to elements 12.1. Now, many/most of my photos will not open because I do not have "permission" to open the files. How do I fix this so I can work wi

I installed elements 12 on a Win 8.1 computer and moved all my photos from my old XP machine. I updated to elements 12.1. Now, many/most of my photos will not open because I do not have "permission" to open the files. How do I fix this so I can work with MY photos?

Yes, the Old Master file has a folder for each year where I find all photos from that specific year. I am attaching a screen shot of the file.
In the meantime i have managed to download all photos (it did not download any video files though in mpg, avi, 3gp, m4v,mp4 and mov format) to a new iphoto library. Unfortunately the photos are quite mixed and often doubled up. I ma considering to purchase iphoto library which checks all duplicates in iphoto. this will save me a lot of time. What do you think?

EIS Installation and Configuration

Hi Everybody,
I am trying to install EIS 9.31 on my laptop (i.e Win2k3 Server), I have successfully installed Essbase and EIS
But I have no idea how to configure(Creating DSN Catalog) in EIS.
I am using Oracle 10g. Can any one please help me on thsi installation.
Already I gone through the installation document but I didn't understand how to configure.
If anyone having installation and Configuring Screen shots please send me to my mail
Mail Id: [email protected]
This is very urgent I need to give presentation on the EIS
Thanks in Advance for your help
Awaiting for your quick Response

I'm not sure what version of software you are looking to install, but for 9.3.1, we just installed our application server (Weblogic), installed Shared Services, supplied the database info and we were good to go. I do believe; however, your mileage will vary depending on the application server you use as some of them have an option for 'automatic' installation and some are manual. (I went the 'automatic' route) You will need to refer to the installation documentation for all of the relevant details, though.

I had my iphone 4s synced to itunes on my work laptop. The IT group at work stripped out that installation and will not allow me to reinstall. My iphone insists it has to sync to my work laptop itunes. How do I change iphone settings to look at an itunes

I had my iphone 4s synced to itunes on my work laptop. The IT group at work stripped out that installation and will not allow me to reinstall. My iphone insists it has to sync to my work laptop itunes. How do I change iphone settings to look at an itunes installation on my personal laptop?

dcotejr wrote:
I had my iphone 4s synced to itunes on my work laptop. ... How do I change iphone settings to look at an itunes installation on my personal laptop?
You cannot.
By Design the iPhone can Only Sync to One iTunes Library at a time.

Satellite U840W PSU5XA - Win 8.1 installation and effective SSD usage

Similar Messages

Maybe you are looking for