Satelltie Pro T110 - Won't load on the first

Hi
Sorry if this question has all ready been posted before but i couldn't find it.
I have Started up my T110 yesterday which i just got and it starts loading windows 7 and then just stops with a error and has a message to turn the computer off. When i switch it back on it comes to the error screen on install the disc or contact admin etc etc. So i start it up hold down 0 and it starts the process again but then stops saying i need to turn the computer off again ?
Any ideas or does this just mean i really need a proper recovery disc from toshiba ?
Thanks,
Vinesh

Hi Vinesh,
Which error message you have received exactly?
Did you already burn the Toshiba recovery disk? This one you have to do yourself and if yes you could start from it.
Otherwise I would contact an authorized service provider for help. There you can get a recovery disk and if its a hardware malfunction, they can repair it.

Similar Messages

My MacBook pro trackpad won't respond to the first tap at times

Hi,
I have a new late 2011 MBP purchased about a week ago. Everything was smooth until my trackpad stopped responding to the first tap. Have to tap it two times to click on some thing. Everything else including the gestures with the trackpad seems fine. I had to reboot to get it working proper again. And the problem rises again after awhile.
Any suggestions?

You have 90 days of free tech support from AppleCare from the date of purchase.
AppleCare: 1-800-275-2273.
For trackpad issues: http://support.apple.com/kb/TS1449
Best.

My Final Cut Pro X won't load past the start-up screen....Why??

I have been using FCPX for about 3 months now and I have had no problems. Out of NOWHERE today when I tried to open up FCPX it loads everything except for one project and it gets stuck. The start-up screen simply says "reading project 1". I have no idea what to do. I use FCPX everyday for editing videos and now I have nothing. I need someone's help.

Not too many fans of FCPX here. Wrong forum. You'll have better luck here. https://discussions.apple.com/community/professional_applications/final_cut_pro_ x

My macbook pro won't load all the way when I start it up.

Lately, my mac book pro has been slow to use, and the colour wheel pops up often. I shut it down earlier today, and now when I try to start it up, it won't load all the way. When I do manage to get to the homescreen, the applications and toolbars won't load. Any ideas what the issue might be and how I can fix it?

It could be a number of issues, Fred.
Have you optimized your photos to no larger than 1000x750 pixels, per the FAQs to the right of this forum? Oversized photos are the chief reason for these types of failures.
http://forums.adobe.com/thread/431851?tstart=0
You also say your videos are MP4s. Are these AVCHD video or are they from a "webbie" camcorder, such as the Flip cam? Flip video uses a proprietary codec that often jams up video editors. This is also covered in our FAQs.
http://forums.adobe.com/thread/437535?tstart=0
Finally, have you ensured that the drive you are saving your video to has adequate free space and is freshly defragmented? You should always have at least 30 gigs of free space on your drive plus 30-50 more for each hour of video you're outputting.
And, if you are exporting to a drive other than your C drive, you should ensure that the drive is formatted NTFS rather than FAT32. FAT32 drives have a file size limit that often chokes video output.

MY MAC WON'T GO PAST THE FIRST WHT APPLE LOADING SCREEN!!!!!!!! HELP PLEASE

Umm..ok..here's the deal. My macbook pro won't go past the first white apple loading screen...right after i start it up. after a while the apple turns into a gray blinking folder with a question mark on it, big problem huh?..doesn't end there...now i figured "hey, how about i try to use the Mac OS X installation disk to see if that'll work?" so i do. Seems as if it were working, but not really..i get past the language choice page, and some other things and now i'm at the 'select a destination' page. There are not options for me to select. I play around with it a little more. Nothing. I restart the computer a couple times. Same results. So now i'm trying to eject the disk, impossible. Someone PLEASE HELP ME....i don't know what to do!!

I have seen the older tiger os when it loads to just a folder with a question mark and it general means that the hard drive has gone bad. I would suggest calling up apple and seeing what they can do for you, most likely you will have to get the drive replaced.

My computer won't load pass the grey start up screen

    MacBook pro won't load pass the grey start up screen?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
     a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 3
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 4
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 5
Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 6
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 7
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 8
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 9
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 10
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider.

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect"

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect", which is Windows lingo for "missing package dependencies". All the computers at my company with 2010 loaded seem to do OK. When I do a Dependencies Walk I get missing Visual C debug dll's missing plus IEshims and wer which both have a whole tree of dependencies missing on my machine. The Windows install is the same "Windows XP version 2002 Service Pack 3" on my PC and the working PC's. So I'm thinking I have to uninstall 2011 and go back to 2010. Is this correct? Those VC debug dll's were installed on the machines with 2010 in them but were not installed in mine.
I've heard the advice to recompile the dll with debug turned off but I don't have access to the source code.
Thanks in advance.

u87 wrote:
Thanks for the reply. This at least tells me that going back to LV2010 is not likely to solve the problem. The missing dll's are:
MFC90D.dll
MSVCR90D.dll
IESHMS.dll
WER.dll
And, once again, IESHMS and WER have other dependencies. So perhaps i need to install the Visual C++ development environment.
IESHIMS.dll is an Internet Explorer DLL that gets usually delay loaded by shdocvw.dll. As delay load it can not cause DLL load errors but only runtime errors. Maybe your DLL has it as direct dependency but that is unlikely since it does not have a documented interface.
WER.dll is Windows error reporting for Vista/Win7.
MFC90D.dll is the Microsoft Foundation classes and MSVCR90D.dll is the MS C runtime library, both as debug variant.
So all the DLLs you mention are actually MS DLLs! You haven't identified the DLL that you try to access in LabVIEW that causes these error messages. IESHIMS and WER are usually delay loaded by any component that needs it and should not likely be used by non MS code.
What is the DLL you try to load into LabVIEW and by whom? Get the provider of that DLL to provide you a non Debug build of the DLL. Installing Visual C on all the machines just to make the DLL load is not a solution, besides that it is likely not legal since I doubt you have that many licenses.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

I bought my MacBook Pro in 2010. This is the first Mac I have owned and recently it is having some difficulty loading we pages, often timing out. This Mac environment is entirely different for me and I am not sure where to begin troubleshooting/clean-up.

I bought my MacBook Pro in 2010. This is the first Mac I have owned and recently it is having some difficulty loading we pages, often timing out. This Mac environment is entirely different for me and I am not sure where to begin troubleshooting and/ or clean-up. I have moderate computer skills and try not to download or access questionable material, however recently I visited the Ap Store and purchased a couple of different aps to use in record keeping and for making a flyer. I am not even sure how to remove these programs to see if it helps.
Any tips or tricks are appreciated.
Thank you!

Time to see about the PRAM battery.
By the way iOS and OS X are different systems.
iOS is the operating system for iPads, iPhones, and iPod touch.
Mac OS X is the operating system for Mac labelled computers.

IMac makes a loud beep on start up, won't load past the blue screen and the black ticking dial appears every few seconds in centre of screen.

Urgent help!
Out of the blue my mac lost the mouse cursor even though it had connection so I rebooted only for the mac to make a loud beep on start up then get stuck at the blue loading screen. It won't load past the blue screen. I've tried to reboot holding down the shift key but no change. I've also shut down, unplugged the main for 15 seconds, re plug and wait 5 seconds before starting up again but no change. Does anyone have any suggestions?
PS: I'm not too sure which systems I am running without being able to check in about this mac. I bought my imac in January or February 2011 if that helps.

The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
http://support.apple.com/kb/HT1547

HT4623 My App Store won't load up the updates tab until my mobile data is switched off?

My App Store won't load up the updates tab until my mobile data is switched off?

My App Store won't load up the updates tab until my mobile data is switched off?

My Yahoo mail account won't load on the iphone 5. What to do?

My Yahoo mail account won't load on the iphone 5. What to do?

Some recommended solutions in this thread
https://discussions.apple.com/message/19739528#19739528

My Apps won't load. The screen from the Apps tab says there a Downloadmistake. What to do?

My Apps won't load. The screen from the Apps tab says there a Downloadmistake. What to do?
Nobody knows?

Link for Download & Install & Setup & Activation problems may help
-Online Chat http://www.adobe.com/support/download-install/supportinfo/

My imac won't load from the white screen with the logo on? What shall I do?

My imac won't load from the white screen with the apple logo and buffering sign? What shall I do..

Try any of the steps suggested in this article that you haven't already tried:
http://support.apple.com/kb/TS2570?viewlocale=en_US&locale=en_US

My laptop won't load past the main blue screen

Hi, I went to restore my laptop to a previous point, it did the usual things, it switched it's self off to then restart again but won't load past the main blue windows 7 home premium page, it it keeps flickering as well, I've tried switching on and off and taking the battery out, nothing works, never had this happen before :-S

Hello again, sorry that the steps that I we have attempted have not resolved the issue. I have a tool that you can try. It's called the HP Support Assistant. If you have any computer issues, the Support Assistant will find them and give you solutions to the issues or resolve them for you. Please click on the link that I have provided. http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-110990-1&cc=us&dlc=en&lc=en...
Thanks again.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HT2499 I bought my MacBook Pro in Aug 2011 - this is the first time I'm trying to watch a DVD on it - I hear the sound but can't see the video - how do I fix this???

I bought my MacBook Pro in Aug 2011 - this is the first time I'm trying to watch a DVD on it - I hear the sound but can't see the video - how do I fix this???

what application are you using to watch the DVD?
is it a burned dvd?

Satelltie Pro T110 - Won't load on the first

Similar Messages

Maybe you are looking for