Saturn (Phoenix+) MS-6309 ATX form-factor motherboard

Question

my mother board says it can support agp x4, but i have a new grapgics card a MSI geforce 4 ti 4200. and it says it is only running at x2. how do i make the computer run this new card at x4?
cheers

Answer 1

agp 1.0 means board cannot run agpx4
Product Family Saturn (Phoenix+) MS-6309 ATX form-factor motherboard  
Category Core  
Product Introduction    
Table of Contents
Revision History
Specifications
Form Factor
CPU Support
System Memory
Core Logic (Chipset)
BIOS Specifications
Upgrade Options
Connectors on board
Compliance
Revision History
Partnumbers Revision # Changes
6780660200
6780660300 1.0 -
6780660400 1.1 4 USB ports support
6780660500 1.1 -
6780660800 1.2 CPU stepping D0 support
Specifications
Form Factor:
ATX 30.4cm. x 19.2cm Form Factor
CPU Support:
Socket 370
Supports Intel PIII Coppermine FC-PGA (Flip-Chip Pin Grid Array) processor 600/100 - 850/100 MHz
Supports Intel PIII Coppermine FC-PGA (Flip-Chip Pin Grid Array) processor 600/133 - 1000/133 MHz
Note: above CPU's are only supported with the latest BIOS version.
66/100/133 MHz Host bus speed processors are supported.
System Memory:
Supports 6 memory banks (3 slots) using three 168-pin unbuffered DIMM.
Supports single or double-sided DIMMS with gold-plated contacts at a clock speed of 66, 100 or 133 MHz.
CPU Bus Frequency Memory Frequency Supported
66 MHz 66, 100 or 133 MHz
100 MHz 66, 100 or 133 MHz
133 MHz 100 or 133 MHz
Supports a maximum memory size of:
768 (128-bit technology) or 384 MB (64-bit technology) registered DIMMs
1.5 GB unregistered DIMMS (256-bit technology)
Supports 3.3 V SDRAM DIMMs
ECC memory checking is supported
Core Logic (Chipset): VIA Apollo Pro133A
VT82C694X system controller
AGP/PCI/ISA Mobile and Deep Green PC ready
GTL+ host bus supports write-combine cycles
Supports separately powered 3.3 V (5 V tolerant) interface system memory, AGP, and PCI bus.
CPU Interface
66/100/133 MHz CPU Front side bus
Sleep mode support
AGP Controller
Synchronous and pseudo-synchronous with the host CPU bus with optimal skew control
PCI AGP CPU Mode
33 MHz 66 MHz 133 MHz 4x synchronous
33 MHz 66 MHz 100 MHz 2x synchronous
33 MHz 66 MHz 66 MHz 1x synchronous
AGP 2.0 compliant
Supports SideBand Addressing (SBA) mode
Graphics Address Relocation Table (GART)
PCI Bus Controller
Supports up to 5 PCI masters
PCI 2.1 compliant, 32-bit 3.3 V PCI interface with 5 V tolerant input
Advanced DRAM controller
DRAM interface synchronous with host CPU (66/100/133 MHz) or AGP (66 MHz) for most flexible configuration
Concurrent CPU, AGP, and PCI access
Different DRAM types may be used in mixed combinations (FP, EDO, SDRAM, ESDRAM and VCM SDRAM)
Different timing for each bank
Optional bank-by-bank ECC (single-bit error correction and multi-bit error detection) or EC (Error Checking only) for DRAM integrity
Advanced System Power Management Support
Dynamic power down of SDRAM
Independent clock stop controls for CPU/SDRAM, AGP, and PCI bus.
Suspend-to-DRAM and Self-Refresh operation
510 pin BGA package
VT82C686A PCI to ISA bridge
PC98 compliant PCI to ISA bridge
Integrated ISA Bus controller with integrated DMA, timer, and interrupt controller
Integrated Keyboard controller with PS/2 mouse support
Integrated DS12885-style real Time Clock (RTC) with extended 256byte CMOS RAM and day/month alarm for ACPI
Integrated USB controller with root hub and four function ports
Integrated UltraDMA-33/66 master mode EIDE controller with enhanced PCI bus commands
PCI 2.2 compliant with delay transaction and remote power management
Supports Type F DMA transfers
Distributed DMA support for ISA legacy DMA across the PCI bus
UltraDMA-33/66 Master Mode PCI EIDE Controller
Dual channel master mode PCI supporting 4 Enhanced IDE devices
Transfer rate up to 33 MB/sec to cover PIO Mode 4, multi-word DMA mode 2 drives, and UltraDMA-33 interface
Support ATAPI compliant devices including DVD devices
Supports PCI native and ATA compatibility modes
Integrated Super I/O controller
Supports two serial ports, IR port, parallel port, and floppy disk controller functions.
Two UARTs for complete serial ports
One dedicated IR port
Multi-mode parallel port: standard mode, EPP and ECP support
Floppy disk controller (16 bytes of FIFO, data rates up to 1Mbps)
USB controller
USB v1.1 and Intel Universal HCI v1.1compatible
Legacy keyboard and PS/2 mouse support
Voltage, Temperature, Fan speed Monitor and Controller
five positive voltage, three temperature, and two fan-speed monitorings
programmable control, status, monitor, and alarm for flexible desktop management
internal core VCC voltage sensing
System Management Bus Interface
Plug and Play controller
352 pin BGA package
256-byte battery-backed CMOS SRAM Real Time Clock (3 volts lithium battery - CR2032).
BIOS Specifications
AMI BIOS with Plug and Play, Advanced Configuration and Power Interface, Advanced Power Management, and Desktop Management Interface support.
2Mbits flash device.
Language support: English.
POST
Upgrade Options
5 PCI extension slots
1 AGP connector
1 Audio Modem Riser connector
Bios: flashable Ami BIOS
Memory:
Supports single or double-sided DIMMS with gold-plated contacts at a clock speed of 66, 100 or 133 MHz.
Supports a maximum memory size of
768 (128-bit technology) or 384 MB (64-bit technology) registered DIMMs
1.5 GB unregistered DIMMS (256-bit technology)
Supports 3.3 V SDRAM DIMMs.
ECC memory checking is supported
8 to 512 MB memory modules are supported
CPU:
Socket 370
Supports Intel PIII Coppermine FC-PGA (Flip-Chip Pin Grid Array) processor 600/100, 650/100, 700/100 MHz and faster.
Supports Intel PIII Coppermine FC-PGA (Flip-Chip Pin Grid Array) processor 600/133, 667/133, 733/133 MHz, 800/133 MHz, 866/133 MHz, 933/133 MHz, 1000/133 MHz and faster.
66/100/133 MHz Host bus speed processors are supported.
Connectors on board
5 PCI bus masters slots
1 AGP slot
1 AMR slot
1 socket 370
3 DIMM
2 IDE
1 Floppy
1 CPU fan
1 System fan
1 ATX power supply
1 Wake-on-LAN
1 Front panel header
1 Front USB header
Compliance
Specification Description
ATX ATX form factor specifications
AGP 1.0 Accelerated Graphics Port
you need agpx 4 graphics port