Savant and WLC 2504

The customer have 1x WLC 2504 and 7x AP 3502i.
He are installing a automation system called Savant, this system use the Bonjour protocol to discovery the services on the network.
I've configured the multicast group on controller and switch (SG300) with IP 239.xxx.xxx.xxx, but the Savant (on iPad) don't finds the service.
Somebody has gone through a similar scenario?
I've used this document: http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml
PS: The customer haven't VLAN
Best regards.

#Disable mdns/bonjour on wlc. place the WLC Management and AP vlan on same subnet. keep the savant server and iphone on same wlan and try.
#WLC 2500 supports only Multicast to Multicast for AP mode, be sure that wired side Multicast is configured properly and working.
#Try with any standard app to verify bonjour and AP mode multicast works.
#it is possible there may be any specific string that require to be added onto bonjour profile for savant to work. do debug mdns all enable and see what is missing.
it is suggested to open TAC case for troubleshooting.

Similar Messages

C3850 WLC enabled and WLC 2504, which one should be Primary controller.

I have 2 designs to make a better solution, please advise me.
I have C3850 and WLC 2504.
1. I will use C3850 as mobility controller (MC) and mobility agent (MA) for WLC 2504. Does it work? or
2. I will use WLC 2504 as MC and MA for C3850.
Can I do both of design?
Which one is better?
Please recommend me a solution.
Thank you in advance.

Hi
2504 (or any legacy WLC) itself having MC/MA & we cannot separate that role on it. You can seperate MC & MA functionality in Converged Access product platforms (3850/3650) only.
Therefore here are the answer to your queries
1. You can have a 3850 with MC/MA functionality. But your 2504 will be a separate controller on your mobility domain. You can allow roaming between these two systems configuring them as mobility peers. You cannot register 3850 connected APs to any other controller other than 3850 WLC itself.So you cannot use these two different system as high availability for AP.
You need to have min 7.6.x on your 2504 in order to configure mobility between 2504 & Converged Access system.
Here is a reference post how you configure roaming between 5508 & Converged Access MC (5760/3850/3650)
http://mrncciew.com/2014/05/06/configuring-new-mobility/
2. None of the documents listed the 2504 could act as MC for 3850/3650(MA). So my understanding is you should have 5760/5508/WiSM2/8500 as MC. But you can test it & see whether 2504 could act as MC which I doubted.
HTH
Rasika
**** Pls rate all useful responses ****

Acs 5.3 and wlc 2504 config with restricted network access

Hello,
i submit you the following issue that i'm actually facing:
i must configure a secured wireless network with access restriction based on SSID. the equipements are : cisco wlc 2504 (soft 7.3) cisco secure acs aplliance 1121 (soft 5.4) .
the users that will connect to the network are regrouped by identity groups, each identity group having it's own SSID. Clearly each group of users must access only one SSID.
i followed the procedure below to configure it:
-- creating user identity groups;
-- creating users and assigning them to the groups;
--- creating authorization profiles for each SSID under policy element/ authorization and permission/network access/authorization profiles and putting the Airespace-Wlan-Id(the SSID number) in the radius tab.
--- assigning the authorization profiles to the identity groups under access policies.
after all these config the users can access the network using there userid/password configured. But the problem is Every user can access every SSID, seems like the restriction is so not very well configured.
i found some documentation on this kind of config but the version of ACS used seems older than the one that i use, so menu are very different.
Please can someone provide with the right steps to follow to achieve this kind of config.
tkx in advance

Yes.. you only have to add the end filter like what I posted... as far as the calling station id in the WLC security tab, it doesn't matter because that is not used when using 802.1x. I would also try to not enable everything that you have just to start from the basic and make sure it works first. The WAP Authentication Method might or might not work for you. Uncheck that for now and when you have a successful authentication, look at the monitor log and see what radius attributes are being sent, because those attributes is what you can use to build your policies.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

WLC 2112 and WLC 2504

This might be a really stupid question but I need to ask just so that I get a definitive answer. I have a customer that is using a WLC 2112 and has maxed out the licenses for the WLC. I have suggested for him to purchase a 2504 with 30 or 40 licenses to replace the existing 2112. He doesn't want to purchase 30 to 40 licenses and doesn't want to remove the 2112 from the network environment. He would rather purchase a WLC 2504 with 15 licenses and just add that into the network.
My question is, will there be a problem running a 2504 and a 2112 on the same network? Or can I just make one a primary and one a secondary?

That should be fine. Just make sure the WLCs are running the same code version and everything should work fine. This is required for APs failover from one WLC to another. You don't want the APs upgrading or downgrading code versions every time the ap moves from the primary to the secondary WLC.
Sent from Cisco Technical Support iPhone App

Prime Infrastructure and WLC 2504 N+1 config syncronization

I've setup 2 cisco 2504 WLC's in a N+1 configuration, before we purchased Prime Infrastructure. Now I'm trying to syncronize the configurations between the two devices in PI. I've setup a configuration group, and it seems using templates will keep the configuration syncronized between the two devices. Is it possible for PI to automatically create the templates based on the current configuration of the device. Plus with PI 2.1 it seems like I have to create a template for every section of the configuration, shouldn't there be just one large template that has all the configurations.

Yes, you should be able to discover templates from the WLC
HTH,
Steve

Configuration of Cisco WLC 2504 with Local LAN static IP and DHCP

I want to configure Cisco WLC 2504 with Local LAN static IP and WLC 2504 with DHCP so that APs can be connect with controller.
Currently i am using WLC 2504 with DHCP so can anyone suggest how to do that..

Hi Sandeep
The info is correct, if we're using code below 7.3.101.0.
This issue is fixed via the below bug id.
CSCto01390 Unable to ping AP's directly connected to a 2500 controller
check the fix that is updated on 7.4, 7.5 RNE.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn75.html
Note
Directly connected APs are supported only in Local mode.
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html
For quick and easy deployment Access Points can be connected directly to 2504 Wireless LAN Controller via two PoE (Power over Ethernet) ports
Thanks
Saravanan

DHCP Error with WLC 2504 and Aironet 2600 setup across subnets

Hey guys
I have just setup a new WLC 2504 controller to manage a WiFi service that will span 6 geographic locations. The local networks at each location are on different subnets (all 192.168.x.x) and are linked up via IPSEC VPN links, and there is Active Directory spanning the sites, with DNS and DHCP servers running at each location.
I tested the WLC at our main office with a single AP, and it worked fine. The AP set itself up, and wireless devices connect with no probs. Great! Yesterday I headed out to one of our remote sites, and connected an AP to their network - and that seemed to work fine too. Within a few minutes I was able to see the WiFi network I'd setup, and my smartphone connected to it straight away (as I'd rpeviously connected at the main office), so I was pretty happy that all was working well.
This morning however I've had notification that wifi performance at the remote site isn't great. I've got someone to check their ip address, and I've found that their IP address and default gateway match the LAN at the main office where the WLC is based - NOT the LAN where the wireless client is. Obvioulsy this is not ideal!
So I guess my question is, what have I done wrong? (I guess I HAVE done something wrong!?). And how can I get wireless clients at remote sites to pick up an IP from the DHCP server at THEIR site?
Any help would be greatly appreciated!
Thanks!

Hello Tim,
What mode your APs are in? Local mode? or FlexConnect mode?
If local mode, then all the traffic will be tunnelled to the WLC and they'll be same as if you are connecting from the WLC location.
If you use FlexConnect APs (which is recommended for remote sites) you can configure FlexConnect groups on the WLC and add each location in a specific group. In that group you can decide what VLAN the users should be in.
Check this link for FlexConnect group configuration
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1230080
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

Best practices for network design on WLC 2504 and 5508

Dear all:
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Maximum amount of AP per port
The scenario when to use all ports in both WLC
Maximum number of clients(users) per port
Bandwidth comsumption of management vs data in order to assign one port for management
I've just found this:
Cisco 5508 controllers have eight Gigabit Ethernet distribution system ports, through which the controller can manage multiple access points. The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller. Cisco 5508 controllers have no restrictions on the number of access points per port. However, Cisco recommends using link aggregation (LAG) or configuring dynamic AP-manager interfaces on each Gigabit Ethernet port to automatically balance the load. If more than 100 access points are connected to the 5500 series controller, make sure that more than one gigabit Ethernet interface is connected to the upstream switch.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/6-0/configuration/guide/Controller60CG/c60mint.html
Thanks for your help.

The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller.
This is an old document. 5508 can now support up to 500 APs if you run firmware 7.X. 2504 can support up to 75 APs if you run firmware 7.4.X.
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Best practice and recommendation is to LAG all ports so you will be able to form a link redundancy. If one link goes down, you have other link to push traffic.

Guest wireless with WLC 2504, Catalyst 4510R+E and ASA 5510

I need to add guest (internet only) wireless to our existing internal wireless and am looking for advice as to the best practice configuration. Existing infrastructure as follows:
WLC 2504
1142 LAPs
4510R+E
ASA 5510
Existing configuration as follows:
WLC management interface and APs addressed on the 192.168.126.0 /25 network
Internal WLAN mapped to the management interface
Management interface VLAN ID 0 (untagged) and dynamic AP management enabled
WLC port 1 (only) connected to 4510 via trunk with native VLAN set to 7 and allowed VLAN set to 7
4510 connected to ASA inside interface (security level 100)
Switchport on 4510 connected to ASA configured as switchport access VLAN 99 (our internet VLAN)
ASA inside interface NOT configured for subinterfaces and is addressed on the 192.168.121.0 /25 network
What is the best way to add guest wireless to our existing configuration?
Note: I need the guest wireless to be filtered by Websense as our internal wireless is
Any advice would be greatly appreciated!

Thank for the reply Scott. The configuration recommendations from Yahya did not work. I set up as he recommended and also added a dhcp scope on the wlc. Client gets dhcp but cannot even ping the wlc much less anything else. Yahya stated above to configure port 2 on the wlc to an access port on my 4510. Aren't all connections from the wlc supposed to be trunk links to the switch? Shouldn't I just leave the management interface on the wlc untagged and add a dynamic interface for each wlan and tag it with the approriate vlan id? And then leave the (one) physical connection on the wlc (port 1) connected to a trunk link on the 4510 that allows the required vlans?
Any input would be greatly appreciated...
JW

Cisco WLC 2504 and ways to authenticate users

Hi All,
What is the ways to make user authenticate to WLC 2504 and what is the best and simple way and what is the differences btw each method _i mean for example need radius server or something else to be exist_ ?
and any one can give me case study for this issue
System consist of Cisco 2504 and Cisco LAP 1140
Thanks

To implement radius based authentication is the best practice for the small & enterprise environment.
Information About RADIUS
Remote Authentication Dial-In User Service (RADIUS) is a client/server protocol that provides centralized security for users attempting to gain management access to a network. It serves as a backend database similar to local and TACACS+ and provides authentication and accounting services:
•Authentication—The process of verifying users when they attempt to log into the controller.
Users must enter a valid username and password in order for the controller to authenticate users to the RADIUS server. If multiple databases are configured, you can specify the sequence in which the backend database must be tired.
•Accounting—The process of recording user actions and changes.
Whenever a user successfully executes an action, the RADIUS accounting server logs the changed attributes, the user ID of the person who made the change, the remote host where the user is logged in, the date and time when the command was executed, the authorization level of the user, and a description of the action performed and the values provided. If the RADIUS accounting server becomes unreachable, users are able to continue their sessions uninterrupted.
RADIUS uses User Datagram Protocol (UDP) for its transport. It maintains a database and listens on UDP port 1812 for incoming authentication requests and UDP port 1813 for incoming accounting requests. The controller, which requires access control, acts as the client and requests AAA services from the server. The traffic between the controller and the server is encrypted by an algorithm defined in the protocol and a shared secret key configured on both devices.
You can configure multiple RADIUS accounting and authentication servers.For example, you may want to have one central RADIUS authentication server but several RADIUS accounting servers in different regions. If you configure multiple servers of the same type and the first one fails or becomes unreachable, the controller automatically tries the second one, then the third one if necessary, and so on.
For more Information : http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_security_sol.html#wp2149947

CME, WLC 2504, 3602i and 7926

Hello,
I have a wlc 2504, several indoor 3602i using Cisco 7926. The APs are in flexconnec mode, signal looks good from the 7926 site survey too. Good coverage anywhere from -50 to -65. I can be standing directly under an AP and the 7926 will loose network connectivity and connect again. A site survey was done before AP placements
Most of my system configuration on the WLC are defaults. Any idea why this is happening
Thanks
Nki

Duplicate post #2.

Why LAP1131AG and LAP11412 cannot to join WLC 2504?

I have WLC 2504, Cisco LAP1131AG and then Cisco LAP1142N. Why LAP1131AG and LAP11412 cannot to join WLC 2504?
this is error code at the Cisco LAP1131AG
*Sep 12 19:30:27.730: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 12 19:30:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*Sep 12 19:30:57.001: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Sep 12 19:31:27.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 12 19:31:32.085: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:32.117: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 12 19:31:32.118: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:33.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:33.112: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 12 19:31:33.117: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 12 19:31:34.104: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 12 19:31:34.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 12 19:31:34.142: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:34.147: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 12 19:31:34.152: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 12 19:31:35.141: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 12 19:31:35.146: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:35.170: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:36.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
this is version LAP1131AG
AP0018.18fc.fd58#sh version
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
AP0018.18fc.fd58 uptime is 9 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"
and then this is version WLC2504
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:19:c4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.100.10
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 36 mins 45 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... ID - Indonesia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +40 C
Fan Status....................................... 4100 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:19:C0
Maximum number of APs supported.................. 5
IP Address management WLC : 192.168.100.10/24
IP Address LAP1142N :192.168.100.102/24
IP Address LAP1131AG : 192.168.100.101/24
Can anyone help my problem?

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected]
cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 90102K/40960K bytes of memory.
Processor board ID FGL1439S15W
PowerPC405ex CPU at 586MHz, revision number 0x147E
Last reset from reload
LWAPP image version 7.6.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C8:4C:75:79:EB:E9
Part Number : 73-12836-03
PCA Assembly Number : 800-33767-03
PCA Revision Number : A0
PCB Serial Number : FOC14234D8Z
Top Assembly Part Number : 800-33775-02
Top Assembly Serial Number : FGL1439S15W
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1026T46E
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.6.130.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:FC:FD:58
Part Number : 73-8962-09
PCA Assembly Number : 800-24818-08
PCA Revision Number : A0
PCB Serial Number : FOC102513DE
Top Assembly Part Number : 800-25544-06
Top Assembly Serial Number : FTX1026T46E
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-A-K9
Configuration register is 0xF

WLC 2504 don't work with mode trunking dot1Q with 3560cg and 2960cg?

Hi
I have a proble with the 3560cg and 2960cg, when i configure the port with "switchport trunk encapsulation doi1q " and "switchport mode trunk" on the interface for the connection with the WLC2504, don't have connection.
I configure others WLC and others switch catalyst (2960, 3550, etc) with the same configuration and this connection work very well.
this is the date from the terminals:
Model SW Version SW Image
WS-C2960CG-8TC-L 12.2(55)EX2 C2960c405ex-UNIVERSALK9-M
Model SW Version SW Image
WS-C3560CG-8TC-S 12.2(55)EX2 C3560c405ex-UNIVERSALK9-M
WLC 2504 IOS-> 7.3.
I don't know what its hapend, or if i need use another command for the 3560cg and 2960cg
Regards

Hi scot
in my case, i configure the 3560 with the vlan 1 for administration and the vlan 100 and 200 for my clients (i use the 2 vlans with 2 wlans from the wlc) and i know that the port must be Trunk, my management interface its taggin with the vlan 1 for the administration and the dynamic interfaces with the respective vlan.
when i configure the 3560 and 2960 i use these command (switchport mode trunk) and i loose the connection with the wlc (i use the same comand with other switch and work very well), the wlc loose the conection with the net.
i dont know the reason for this failure, and i know if the wlc have management interface untugged, only work with this vlan (vlan native or vlan access) and don't work with the others vlans for the wlans.
I wish to know if the IOS or if exist another configuration for the 3560 and 2960 works with the WLC correctly or its problem of the IOS
Thaks for the help
Regards

WLC 2504 can't change WAP name or switch off CDP via WLC gui

Hi All,
Please can you assist? I have 1 x Cisco WLC 2504 & 2 x Cisco WAP AIR-CAP1602I-E-K9 running 7.4.100.60.
All three devices are installed and working correcty within a corporate environment. However, there are a few tweaks that I would like to do, to tidy up the configuration and switch certain elements on or off. For example, my core networking hardware is Huawei and I would like to switch off 'CDP' on the WAP's as the associated error messages are filling up my logging buffer on my switch. So, I https to my WLC, locate the WAP in question, goto 'interfaces' and untick the box for 'CDP state' hit apply, then I get the following error message "controller name is mandatory when controller ip address is configured" and then the tick reappears!
At present I have two WAP's. Both have static IP addresses and both are reachable on the network. The one WAP did allow me to change the name to something meaningful, but the other WAP would not let me and still has the default MAC address as its name. I have the same issue, when I try to change the name on the WAP it says "controller name is mandatory when controller ip address is configured"
I have also tried to CLI directly in to the WAP to make these alterations, but as soon as i launch 'putty' it quits out. I guess this is locked down once the WAP's associate with the WLC.
And around I go.... Someone must have been in this situation, what am i missing? Thanks in advance!

Hi Andy,
By default SSH & Telnet is disabled for WLC controlled APs. So you have to enable it first via WLC GUI in order to access the AP via telnet or SSH.
Wireless -> Select your AP -> Advanced -> Tick Telnet/SSH boxes.
If you could not change AP name via WLC GUI (it may be a bug), but as I said earlier try to change it via WLC CLI (not AP CLI itself). SSH to your WLC & then try the following.Old AP name is the one with its mac address.
(WLC) >config ap name
(WLC) >save config
Are you sure you want to save? (y/n) y
Configuration Saved
HTH
Rasika
*** Pls rate all useful responses ****

WLC 2504 firmware upgrade

Upgraded my Cisco 2504 from 7.0.220.0 to 7.4.111.0
and upgraded my field upgrade bootloader to 1.0.18.
Now I cannot configure my WLC from the web via IP. Had it configured properly with VLAN, switch and my ASA 5520.
Does this have to do with the ACL's on the WLC.
I've been looking for documentation can't find much in terms of best practices for traffic.
My CPU ACL on wired and wireless are disabled with no ACL for the CPU.
Any suggestions or help would be greatly appreciated.
Thank you
Carlos

Hello Scott,
I figured it out. I had to do from CLI a reset system command. Once I did that everything came back up. I did not know that field upgrade and firmware upgrade took so long. The instructions say to just to a save and reboot. I found out that you need to do a reset system command again from the CLI.
Appreciate the assistance.

Savant and WLC 2504

Similar Messages

Maybe you are looking for