Save webpage pdf. Using Macbook Pro, 10.7.5. Remedy?
I'm unable to open a saved webpage pdf. When I click on it to open, the message is: "The file '...' could not be opened because it is empty." Using Safari, Macbook Pro, 10.7.5. Remedy?
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.
Similar Messages
-
Using MacBook Pro to convert pdf to word doc...downloaded...converted, and what I got was illegible. What's the deal? Did I miss a couple steps along the way?
Hi Deborah,
Please Elaborate your issue so that i can assist you better.
Regards,
Rahul -
hi, i am badly in need of help. i partitioned my mac hd yesterday and now the boot camp is nt working as i was using win 7 on it. i am using macbook pro 13'' 2011. plz help me. anxiously waiting for response... specially from "Christopher murphy"
you can't add or mofidy partition numbers. especially not if and once you have windows installed.
boot from Windows 7 DVD afterwards
but first you have to tell us and Christopher what and how you partitioned your system.
Successful setup of OS X Lion + Data Partition + Bootcamp Win7 Ult
https://discussions.apple.com/thread/3293948
So after many, many hours I think I've finally figured out how to successfully setup Mac OS X Lion on one partition, a seperate data partition, and Windows 7 Ultimate on a Bootcamp partition . Here is a screenshot of my setup on my 13" MacBook Pro
Thread with suggestions on Windows backup methods:
https://discussions.apple.com/thread/3798090
Paragon CampTune
Paragon CampTune is a commercial product that is designed expressly for this task. http://www.paragon-software.com/home/camptune/ It consists of a downloadable ISO that needs to be burned to a disc and booted from in order to resize the partitions costs US$19.95.
Securing Dual-System Configuration
Imaging is still the most affordable and robust way to secure computer data. Unfortunately Mac OS X backs up only HFS+ volumes, leaving Windows with dual-system configurations unsecured. You can permanently lose all of your data unless you have a Windows-compatible backup solution.
Paragon’s CampTune and Paragon’s Drive Copy for Mac can secure the entire dual-system configuration. CampTune creates traditional images of volumes or entire hard disks, Drive Copy can copy them to other disks. In case of an emergency, you can restore the previously created image or copy all your data back to its original state.
GParted Live
GParted Live is similar to CampTune as it is also distributed as a bootable image that needs to be copied to a CD/DVD or USB flash drive. As free and open source software, distributed under the GPL, it will always be available free. Since it has more functions than CampTune, it may be harder for folks who are not as experienced with partitioning hard drives. http://gparted.sourceforge.net/
iPartition
Coriolis Systems' iPartition is a £29.95 ($44.95 US) utility that runs in Mac OS X and allows resizing of all of the relevant partition formats, including HFS+, FAT32, and NTFS. It provides a Mac-oriented user interface that may be easier to manage than some of the free utilities. As it is not capable of resizing the boot disk, it requires a bootable external disk or a boot DVD. (A tool to create a boot DVD is included.)
Paragon Partition Manager
From the makes of CampTune is a commercial tool that is similar in functionality to GParted Live, but has a more polished/friendly user interface than GParted Live. Previously only the US$79.95 Professional version supported all the features required for this, but as of version 11 the US$39.95 Personal version has also been reported to work. http://www.paragon-software.com/home/pm-personal/
Winclone/Disk Utility
Winclone is a free tool for creating and restoring backup images of your Windows partition. One of its key features is that it can restore to a larger partition than the one the image was created from.
NOTE: Winclone has been discontinued, but for now remains available and capable of completing these tasks (including creating and restoring Windows 7 images).
Winclone updated to support Lion Winclone updates and download
Disk Utility can resize HFS+ (Mac OS) partitions, but is currently incapable of resizing NTFS partitions, so you could use it to reduce the size of the HFS+ partition and create a new larger placeholder MS-DOS (FAT) partition
The full process would be:
Backup Windows partition with Winclone.
(if the new Windows partition is smaller than the old one make sure you set the preferences in Winclone to save the image as an uncompressed dmg)
Delete old Windows partition
Resize current Mac Partition
Create new Windows partition as MS-DOS (FAT) in free space after Mac OS partition.
(If the new Windows partition is smaller than the old one an additional step is required: shrink the filesystem on the image by selecting Tools->Shrink Windows (NTFS) Filesystem)
Reboot your computer for the new Windows partition to mount properly (winclone may not restore if you don't reboot)
Restore Winclone partition over new Windows partition
An alternate Winclone based process is described in the External Guides section
Native OS utilities
MR user Kazyua reports that you can use the disk management utilities provided with the current operating systems if you want to do it manually. Windows 7 and OS X both have partition resizing functions built in. In OS X, open Disk Utility and manually shrink the mac HFS+ partition by dragging the lower right corner. Then in windows go to the start menu and type "disk management" into the search box then hit enter. You should get an overview of the drives you have and the individual partitions. Right-clicking on the partition gives an "Extend Volume" option. The Windows NTFS volume should then be extended into the free space you created with Disk Utility. This method has not worked for other users, so try at your own risk.
Resizing under VMWare Fusion
If you are looking to allocate more space to Windows under VMWare please refer to the following thread http://forums.macrumors.com/showthread.php?t=828182
From http://guides.macrumors.com/Extend/Resize_Boot_Camp_Partition
Thread with suggestions on Windows backup methods:
https://discussions.apple.com/thread/3798090 -
Hi,
I am using MacBook Pro .
I am not getting menial to use HP LeaserJet 1018 . It is not available on HP web-sight as well .
How do I get this suitable to MacBook pro ?
Please help me with this.
Ajit Kanakiahttp://h10032.www1.hp.com/ctg/Manual/c00585348.pdf
http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/LaserJet-1018-driv er-for-Mac-OS-X-10-8-2/td-p/2294795 says you need to use the 1022 driver. -
So, I bought a used MacBook Pro (April 2010) today and I plan on restoring it to factory settings. I saw on a video of a factory restore that it will prompt for an apple id of the original purchaser. Now, I did find a buried thread on the subject and the answer was that I will need to purchase OSX. Not sure if this is true or there are more details than that. If this answer is correct, would the computer automatically recognize that my apple id has a purchased copy? Also, on another video I saw that discs such as the OSX and iLife are required. So in a nutshell I have no idea on how to go about this factory restore deal. This will be my first mac purchase so bear with me. If I havent been detailed enough let me know, ill try to explain better. Thanks!!
Do you have the original installation discs that came with the computer? If so you only need to boot from the disc, erase the hard drive, then install Snow Leopard.
Upgrade Paths to Snow Leopard, Lion, and/or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99. To access the App Store you must have Snow Leopard 10.6.6 or later installed.
Upgrading to Snow Leopard
You must purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
Snow Leopard General Requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider;
fees may apply.
6. Some features require Apple’s MobileMe service; fees and
terms apply.
Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mountain Lion - System Requirements
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
7. Xserve (Early 2009) - Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table - RoaringApps.
For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion. -
I'm trying to reinstall Mavericks on used Macbook Pro. When I log in to my Apple ID, it says it was not the same ID used to purchase Mountain Lion. I need to change user/admin as a lot of the folders and apps are in Chinese!
The first thing you should do with a second-hand computer is to erase the internal drive and install a clean copy of OS X. How you do that depends on the model. Look it up on this page to see what version was originally installed.
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc, which you can get from the Apple Store or a reputable reseller — not from eBay or anything of the kind. If the machine has less than 1 GB of memory, you'll need to add more in order to install 10.6. I suggest you install as much memory as it can take, according to the technical specifications.
If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for some MacBook Air models. If you don't have the media, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To boot from an optical disc or a flash drive, insert it, then reboot and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, you don't need media. It should boot into Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
Once booted from the disc or in Internet Recovery, launch Disk Utility and select the icon of the internal drive — not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive, which is what you should do.
After partitioning, quit Disk Utility and run the OS X Installer. When the installation is done, the system will automatically reboot into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
You should then run Software Update and install all available system updates from Apple. If you want to upgrade to a major version of OS X newer than 10.6, buy it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the previous owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed — you have to repurchase them.
If the previous owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Apple customer service has sometimes issued redemption codes for these apps to second owners who asked.
If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able toauthorize it under your ID. In that case, contact iTunes Support. -
I recently bought a used macbook pro. I can pretty much do everything I need on it until I want to change setting and such things. Then it asks me for an administrator password which I do not know or have. On top of that I do not have the OS disc either. Is there a way I can SAFELY reset or delete the password so I can set my own without the possibility of screwing thing up. LIke I said I can do most anything. I figured this out when attempting to tether it to my smartphone for internet access (I do all the time from my desktop but my desktop is a PC so things are a little different) I am a very new mac user, I have always been a devoted PC user until now. I have to say I am really loving my macbook pro I may just stick with mac from now on (if I can get this problem figured out without too much stress.
I am looking for the safest and best way to fix this issue where nothing I do would mess up the laptop. I can use it now and I do not want that to change, I just want to be able to change my setting and set a password of my own. PLEASE HELP, THANX!Hi
There actually is a slightly easier way in OS X 10.5 or greater.
1. Start up in single-user mode (hold Command-S as the computer starts up).
2. Type: mount -uw /
3. Press Return.
4. Type this:
passwd (user's short name)
Replace "(user's short name)" with the short name of the user account whose password you wish to reset. If you are not sure what the account name is, you can get a list of user names by typing: ls /Users
5. Press Return.
6. Enter a new user password.
7. Press Return.
8. Type: reboot
9. Press Return. -
I,m using macbook pro retina, I have changed the language from arabic to Endlish through system preference, but still I find that password and downloading are coming in arabia, when I start my computer it show password request in Arabic.
http://support.apple.com/kb/ht4102
-
How can i copy files from one external hard disk to another using macbook pro with retina display
How can i copy files from one external hard drive to another using macbook pro with retina display?
That's odd - if you open Disk Utility (Applications->Utilities) and select the disk(s), how are they formatted? If you're only going to be used with your Mac, they should be formatted as "Mac OS Extended (Journaled)".
Clinton -
I have a macbook pro that I want to give to my son for school. I just purchased a newer (used) macbook pro with more HD and memory to replace the one I use for work. I need to set up the new book and transfer all my stuff over, then clean the older one up for my Son. I'm concerned because the newer book I purchased on ebay. It didn't start up a if it were a clean machine. I turned it on and it is full of lots of programs and I'm worried the previous owners files and information are on the computer. They both have the OS X 10.9.5 (13F34) software. I updated to the new iLife on the older one, the newer one has 09. I would appreciate the steps I should take. I have everything backed up on the older book through drop box and cloud, so I'm ready. Also the seller told me the computer would have Mavericks already installed, but I don't see it.
Before buying a second-hand computer, you should have run Apple Diagnostics or the Apple Hardware Test, whichever is applicable.
The first thing to do after buying the computer is to erase the internal drive and install a clean copy of OS X. You—not the original owner—must do that. Changes made by Apple over the years have made this seemingly straightforward task very complex.
How you go about it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
It's unsafe, and may be unlawful, to use a computer with software installed by a previous owner.
1. If you don't own another Mac
a. If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller—not from eBay or anything of the kind. If the machine is very old and has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
b. If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for a MacBook Air. You should have received the media from the original owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To start up from an optical disc or a flash drive, insert it, then restart the computer and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
c. If the machine shipped with OS X 10.7 or later, you don't need media. It should start up in Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
d. Some 2010-2011 models shipped with OS X 10.6 and received a firmware update after 10.7 was released, enabling them to use Internet Recovery. If you have one of those models, you can't reinstall 10.6 even from the original media, and Internet Recovery will not work either without the original owner's Apple ID. In that case, contact Apple Support, or take the machine to an Apple Store or another authorized service provider to have the OS installed.
2. If you do own another Mac
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to prepare a USB device, then start up the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can start from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
3. Partition and install OS X
a. If you see a lock screen when trying to start up from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another service provider to be unlocked. You may be asked for proof of ownership.
b. Launch Disk Utility and select the icon of the internal drive—not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
c. An unusual problem may arise if all the following conditions apply:
OS X 10.7 or later was installed by the previous owner
The startup volume was encrypted with FileVault
You're booted in Recovery mode (that is, not from a 10.6 installation disc)
In that case, you won't be able to unlock the volume or partition the drive without the FileVault password. Ask for guidance or see this discussion.
d. After partitioning, quit Disk Utility and run the OS X Installer. If you're installing a version of OS X acquired from the App Store, you will need the Apple ID and password that you used. When the installation is done, the system will automatically restart into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
e. Run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the original owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed—you have to repurchase them.
4. Other issues
a. If the original owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're irrevocably linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
b. If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
c. When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a lifetime limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an iCloud account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information. The setup limit doesn't apply to Apple ID accounts used for other services, such as the iTunes and Mac App Stores, or iMessage. You can create as many of those accounts as you like. -
Purchased a used macbook pro with Mountain Lion. My old Mac runs Snow Leopard is backed up to Time machine. How do I register the operating system to me and how do I use Time Machine to move my files to the new used computer?
If you look at the User Tips tab, you will find a write up on just this subject:
https://discussions.apple.com/docs/DOC-4053
The subject of buying/selling a Mac is quite complicated. Here is a guide to the steps involved. It is from the Seller's point of view, but easily read the other way too:
SELLING A MAC A
Internet Recovery, and Transferability of OS & iLife Apps
Selling an Old Mac:
• When selling an old Mac, the only OS that is legally transferable is the one that came preinstalled when the Mac was new. Selling a Mac with an upgraded OS isn't doing the new owner any favors. Attempting to do so will only result in headaches since the upgraded OS can't be registered by the new owner. If a clean install becomes necessary, they won't be able to do so and will be forced to install the original OS via Internet Recovery. Best to simply erase the drive and revert back to the original OS prior to selling any Mac.
• Additionally, upgrading the OS on a Mac you intend to sell means that you are leaving personally identifiable information on the Mac since the only way to upgrade the OS involves using your own AppleID to download the upgrade from the App Store. So there will be traces of your info and user account left behind. Again, best to erase the drive and revert to the original OS via Internet Recovery.
Internet Recovery:
• In the event that the OS has been upgraded to a newer version (i.e. Lion to Mountain Lion), Internet Recovery will offer the version of the OS that originally came with the Mac. So while booting to the Recovery Disk will show Mountain Lion as available for reinstall since that is the current version running, Internet Recovery, on the other hand, will only show Lion available since that was the OS shipped with that particular Mac.
• Though the Mac came with a particular version of Mac OS X, it appears that, when Internet Recovery is invoked, the most recent update of that version may be applied. (i.e. if the Mac originally came with 10.7.3, Internet Recovery may install a more recent update like 10.7.5)
iLife Apps:
• When the App Store is launched for the first time it will report that the iLife apps are available for the user to Accept under the Purchases section. The user will be required to enter their AppleID during the Acceptance process. From that point on the iLife apps will be tied to the AppleID used to Accept them. The user will be allowed to download the apps to other Macs they own if they wish using the same AppleID used to Accept them.
• Once Accepted on the new Mac, the iLife apps can not be transferred to any future owner when the Mac is sold. Attempting to use an AppleID after the apps have already been accepted using a different AppleID will result in the App Store reporting "These apps were already assigned to another Apple ID".
• It appears, however, that the iLife Apps do not automatically go to the first owner of the Mac. It's quite possible that the original owner, either by choice or neglect, never Accepted the iLife apps in the App Store. As a result, a future owner of the Mac may be able to successfully Accept the apps and retain them for themselves using their own AppleID. Bottom Line: Whoever Accepts the iLife apps first gets to keep them.
SELLING A MAC B
Follow these instructions step by step to prepare a Mac for sale:
Step One - Back up your data:
A. If you have any Virtual PCs shut them down. They cannot be in their "fast saved" state. They must be shut down from inside Windows.
B. Clone to an external drive using using Carbon Copy Cloner.
1. Open Carbon Copy Cloner.
2. Select the Source volume from the Select a source drop down menu on the left side.
3. Select the Destination volume from the Select a destination drop down menu on the right
side.
4. Click on the Clone button. If you are prompted about creating a clone of the Recovery HD be
sure to opt for that.
Destination means a freshly erased external backup drive. Source means the internal
startup drive.
Step Two - Prepare the machine for the new buyer:
1. De-authorize the computer in iTunes! De-authorize both iTunes and Audible accounts.
2, Remove any Open Firmware passwords or Firmware passwords.
3. Turn the brightness full up and volume nearly so.
4. Turn off File Vault, if enabled.
5. Disable iCloud, if enabled: See.What to do with iCloud before selling your computer
Step Three - Install a fresh OS:
A. Snow Leopard and earlier versions of OS X
1. Insert the original OS X install CD/DVD that came with your computer.
2. Restart the computer while holding down the C key to boot from the CD/DVD.
3. Select Disk Utility from the Utilities menu; repartition and reformat the internal hard drive.
Optionally, click on the Security button and set the Zero Data option to one-pass.
4. Install OS X.
5. Upon completion DO NOT restart the computer.
6. Shutdown the computer.
B. Lion and Mountain Lion (if pre-installed on the computer at purchase*)
Note: You will need an active Internet connection. I suggest using Ethernet if possible because
it is three times faster than wireless.
1. Restart the computer while holding down the COMMAND and R keys until the Mac OS X
Utilities window appears.
2. Select Disk Utility from the Mac OS X Utilities window and click on the Continue button.
3. After DU loads select your startup volume (usually Macintosh HD) from the left side list. Click
on the Erase tab in the DU main window.
4. Set the format type to Mac OS Extended (Journaled.) Optionally, click on the Security button
and set the Zero Data option to one-pass.
5. Click on the Erase button and wait until the process has completed.
6. Quit DU and return to the Mac OS X Utilities window.
7. Select Reinstall Lion/Mountain Lion and click on the Install button.
8. Upon completion shutdown the computer.
*If your computer came with Lion or Mountain Lion pre-installed then you are entitled to transfer your license once. If you purchased Lion or Mountain Lion from the App Store then you cannot transfer your license to another party. In the case of the latter you should install the original version of OS X that came with your computer. You need to repartition the hard drive as well as reformat it; this will assure that the Recovery HD partition is removed. See Step Three above. You may verify these requirements by reviewing your OS X Software License. -
Just bought a used MacBook pro after my previous died. I want to migrate my applications, data, etc from a time machine backup of the old computer to the new. Will this affect, or overwrite the Apps., data, etc existing on the new machine?
No. Only those Apps that are not installed on the new will migrate over.
-
How to load time machine on a used macbook pro
I recently was given a used MacBook pro. My old MacBooks logic board was going and eventually went, but before it did I used time machine to back it up. I want to load my time machine macbook info onto the pro. I cant seem to do this, since TimeMachine just wants to create a new profile for the new Mac on the external. How can I do this? They are both running the OS X 10.8.2
Thanks,
NateJust startup in Recovery mode (Command and R keys held down whilst booting) and boot into your Recovery partition. Make sure that your TM backup is hooked up. In the utility menu, select 'restore from Time Machine' option. You'll be able to choose the drive and the latest TM backup.
Good luck,
Clinton -
Is it worth to get a used macbook pro
hi, guys.
I am looking at a used macbook pro from early 2009 with configuration
2.66Ghz Core 2 Duo
8GB of DDR3 RAM (2x4GB)
500 GB SSD hard-drive [which advertisement said it was upgraded at Apple Store for 600 dollars]
Nvidia GeForce 9600M GT (512MB) and Nvidia GeForce 9400M (256MB)
17" Hi-Res Antiglare TFT active-matrix
1920 x 1200 Native Resolution
FaceTime HD Camera, Omnidirectional Mic
Slot-Loading SuperDrive
802.11n Wi-Fi, Bluetooth 2.1+EDR
Mac OS X 10.6.8
there's a dent on the right lower corner, which is acceptable.
the reason the guy sell it is that he got a new model.
why I plan to buy it is that I need to implment all kinds of programming stuff. I have a thinkpad with Ubuntu, but its wifi connection is very bad.
Mac is perfet for programmers.
New mac are pricing.
Any inputs will be appreciated. I want to konw
is it worth to invest a 4 years old macbook pro?
if i buy it, what should I check?
seller said 1000 dollars for the machine.
thanksIt's worth 4 to 500 dollars, none of the 'extras' (the HDD and the Ram) make it any more valuable.
How long it will last is speculative, I have a G4 portable that is 8 years old and works fine still, and I have seen Macs die when switched on for the first time so ....
Offer 400, 500 max, if it lasts a year it was expensive, 2 years it was a fair price, 3 years and you got a deal.
One more thing, as it was delivered new wth Leopard or Snow Leopard you must INSIST on receiving the original discs that accompanied it, they can not be downloaded and you will need them. -
Before upgrading to Lion on my MacBook Pro I could print on the HP C4580 All in One using HP Desktop with Windows 7 and using MacBook Pro with no problems. I upgraded to Lion now can only print when I shut down and restart my MacBook. If using the desktop or the Microsoft Office on my MacBook it kicks the printer offline and I have to restart my laptop. I called Apple and they said they did not support 3rd party software. I had previously purchased the printer through Apple with a desktop. I installed the new driver from HP and removed it, reinstalled. Guess what, same problem. Can anyone tell me how to make lion work. Apple will not provide help. Have a iPad and with a small app for $7.00 it prints great. HELP
You must work for Apple. Contacted the vendor downloaded their app. Everytime I open Microsoft Office for Mac it kicks printer off line and if I print from a Windows computer (which printer works perfect) it kicks printer off line. If I restart Mac it will print the item in the printer. Don't care what Apple says, prior to loading Lion never had any problems. Sounds as if Apple programers goofed up and just don't want to admit it and correct their problem. Your comments did not solve any problems, asking for help not Apple support.
-
What to look for when buying a used MacBook Pro? Tips
Here to acquire a few tips on purchasing a used Macbook Pro. I am not graced with an Apple Store in my area, so I must rely on my own sub par geek wit and with the help of yours.
Tips I know.
Checking Battery Cycles and mAh capacity.
Looking for third party applications.
Request the original StartUp/Install Disks.
Checking memory ratios...Shop your local and nearby Craigslist websites, starting with:
http://tampa.craigslist.org/
Read this excellent post by frequent contributor JasonFear about buying and selling through Craigslist:
http://discussions.apple.com/click.jspa?searchID=-1&messageID=9958349
Avoid Ebay.
If third-party applications or other software are included, they add nothing at all to the value of the machine unless you are given the original installer discs for them. Otherwise, they are just pirated software that you can't reinstall if you ever need to.
Message was edited by: eww
Maybe you are looking for
-
Also, I have a timer that lets me know how long the trigger has been active. I want to know if it is possible if that time would be reset everytime the trigger goes off. Attachments: Code.vi 113 KB
-
How to use Dashboard as a cut & paste software
Hi ! I´ve hard to understand the function of "Dashboard" - I thought that the software could be a help for me to cut/copy pictures on websites for an example - I thought that I could mark an area on a site, copy the are and save it to iPhoto or copy
-
Firefox 3.6.13 / Mac OSX.6.6, open-PDF-with Preview preference is not retained across sessions
Using Firefox 3.6.13 / Mac OSX 10.6.6, when I visit PDF-file links, the default ALWAYS reverts to saving file in downloads folder. I go to Firefox -> Preferences -> Applications -> Search PDF, set Open-With Preview (Default). Fo rhtat session of Fire
-
I downloaded Microsoft office on my IMac. I share this with someone and we have separate Apple Id's.
Is it possible to share this with the other Id on the same computer. If so, how do I do it? Thank you in advance.
-
Missing Database Options under Configure menu in Sequence Editor
In my TestStand 4.0 Sequence Editor, the "Database Options" is missing under "Configure" menu. Does anyone know how to enable this option? Thanks