Saving scanned doc error message when using Mac Maverick with HP Photosmart C4795
When I use HP Scan to scan documents with my HP Photosmart C4795 it scans fine. The problems comes when I try to save the scanned document. I get one of two things, an error message or black document. I get an error that states "An error has occurred saving the file because it could not be written to. Check the properties for the file to make sure it is not read-only. I know that's the location is not read only because I save documents there all the time from other programs. When I get the black document, I open the file and its a black page with white lines going across.
This started happening when I upgraded to Maverick. When I had snow leopard I didn't have this problem. I looked for update drivers and there aren't any available on the HP software & drivers webpage. HP help! Any suggestions please help.
Hi,
That happens due to lack of compatibility of the HP Scan application for your device with Mavericks, it is not intended for the operating system and will cause issues while saving a file.
Be sure to run Software Update, then scan using Image Capture or Preview as listed below.. those are the scan solutions provided for Mavericks:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03550518&tmp_task=useCategory&cc=us&dlc=en&lc=e...
Once you launch Image Capture, I would suggest keeping it on the dock for easier access.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution
Similar Messages
-
ERROR MESSAGE WHEN USING PACK COMMAND Missing file ////presenter.css Command then fails
Also: "This course requires JavaScript to be enabled in your browser. Please enable JavaScript, then relaunch the course." I have Java enabled in all browsers
Thoughts? Using Presenter 10 Win 8.1 Intel I7 new HP with plenty of memory
ThanksI had saved one copy as an .asp but then resaved it to .xhtml
I'm assuming this is a static web site. Rename (F2) all your pages with .html or .htm extension.
.xhtml is not a valid extension.
Nancy O. -
Dreamweaver CC generates one of 3 error messages when using find and replace is used more than twice in succession. "While executing onLoad in bc_afterSave.htm, the following JavaScript error(s) occurred: At line 188 of file C:\Program Files (x86)\Adobe|Adobe DreamweaverCC|Configuration|Shared|BC\JS\bc_sites.js": out of memory"
or
While executing runCommand in File_Save.htm, a JavaScript erroroccurred.
or
While exciting getDynamicContent inAdressURL.htm, a Javascript erroroccirred.
Any thoughts - I end up closing DWCC and reopening. Will work for two additional Find and Replace before the error messaged\s popup again.bkaufman43 wrote:
Thanks Jon. I tried all of those solutions before posting. Same problem. It seems that the problem is tied to DWCC. Do not have the problem when using DW6 on Win8.1. When running DWCC on a Win7 pc, we get the same error message. When running DW6 on Win 7, f&c works fine. It seems to be a bug in DWCC. DWCC works flawlessly on our Macs.
The same steps apply to DWCC, you just need to choose the CC folders rather than the DWCS4-6 versions that the page talks about. The layout of CC's folders hasn't changed from the older versions which is why, I think, Adobe hasn't updated the troubleshooting page as of yet.
As Nancy mentions, a 38,500 page site is sort of ridiculously large for a static website, that could be part of the problem, but your response quoted above leads me to think you may have tried the troubleshooting steps in the wrong version of the program. Could you confirm that? -
Error message when using xrpcc in JWSDP 1_0_01
Dear all,
I've got the following error message when using xrpcc of JWSDP 1_0_01 for my config.xml file.
D:\jwsdp-1_0_01\Message>xrpcc -classpath build -both -d build config.xml
error: invalid element "{http://java.sun.com/jax-rpc-ri/xrpcc-config}configurati
on" in configuration file (line 2)
The content of 'config.xml' is shown as follows.
<?xml version="1.0" encoding="UTF-8"?>
<configuration xmlns="http://java.sun.com/jax-rpc-ri/xrpcc-config">
<rmi name="MessageService"
targetNamespace="http://messageuri.com/wsdl"
typeNamespace="http://messageuri/types">
<service name="MyMessage" packageName="Message">
<interface name="Message.MessageIF"
servantName="Message.MessageImpl"/>
</service>
</rmi>
</configuration>
Thank you for your kind attention!
Regards,
EddieThanks all! I've already solved my previous problem, however, i got another one now.
=========================================================
error: unknown model info in configuration file (line 5)
=========================================================
<?xml version="1.0" encoding="UTF-8"?>
<configuration xmlns="http://java.sun.com/xml/ns/jax-rpc/ri/config">
<rmi name="MessageService"
targetNamespace="http://messageuri.com/wsdl"
typeNamespace="http://messageuri.com/types">
<service name="MyMessage" packageName="Message">
<interface name="Message.MessageIF"
servantName="Message.MessageImpl" />
</service>
</rmi>
</configuration>
Thanks,
Eddie -
Error message when using search
why do i keep getting an error message when using the "search" tabe in iTunes. This happend whe i upgraded t the latest version of itunes.
Well, I believe JHeadstart does not really have this functionality.
One way is use a Query Operator 'startsWith', but then you always query like LIKE '<entered search value>%'
This is probably not what you want...
But you could hack it into advancedSearch in YourApplicationModuleImpl
try {
if (viewCriterium.getQueryValue() != null) { //This is where exception JHS-00116 is raised...
value = viewCriterium.getQueryValue().toString();
} else {
value = null;
catch (NumberFormatException ex) {
//insert check for wildcard
value = viewCriterium.getValue().toString();
if (value.indexOf('%')>=0) {
sLog.debug("Ja, een wildcard!!!");
operator = "LIKE";
} else {//original exceptionhandling code here...
...and a bit later, add test for "LIKE":
if (viewCriterium.isDate() || viewCriterium.isString() || "LIKE".equals(operator)) {
value = "'" + value + "'";
very nasty code, and does not raise an exception for searches like '%xxx'
Good luck,
HJH
Edited by: HJHorst on Mar 5, 2009 12:03 AM -
Error message when using FM 'BAPI_BUPA_ADDRESS_CHANGE'.
I'm continually getting an error message when using FM 'BAPI_BUPA_ADDRESS_CHANGE'. The message being 'Table BAPIADTEL entry to be changed not found in target system'.
I have looked up this message but all links seem to refer to FM 'BAPI_BUPA_CENTRAL_CHANGE', which I'm not using, and has different parameter settings.
I'm simply trying to update the telephone number and I'm updating strcuture BAPIADTEL and BAPIADTELX but still the message appears. I know that there is a really simple reason for this, but I have been double-checking everything and experimenting with lots of different areas, but with no effect.
Has anyone encountered this problem using the specific FM ''BAPI_BUPA_ADDRESS_CHANGE' ?.
JasonHi Jason,
In case your database tables had already value for field telephone number, then only the flag should be "U".
If the telephone number field was empty, and we will try to change it by using the flag as U, it wont work. In this case, we should be using "I".
I even wrote that before in this post, but somehow I guess the post was locked, and a lot of comments from you and me were not visible apart from the first two. So, I couldnt get any update from you.
Anyway, its good that its working for you. Thank you for the update.
Regards,
Susanta -
Error Message-When using DataScroller
Hi
I get the following error message when using DataScroller. I am using Oracle Jdeveloper 9i production release.
Application Error
Return
Error Message: null
java.lang.NullPointerException
int oracle.jbo.server.ViewRowSetIteratorImpl.scrollRange(int)
int oracle.jbo.server.ViewRowSetImpl.scrollRange(int)
int oracle.jbo.server.ViewObjectImpl.scrollRange(int)
int oracle.jbo.html.jsp.datatags.RowsetNavigateTag.doStartTag()
void DataHandlerComponent.jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.GetParametersRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.EvermindPageContext.include(java.lang.String)
int oracle.jbo.html.jsp.datatags.ComponentTag.doStartTag()
void Rate.jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.GetParametersRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.EvermindPageContext.include(java.lang.String)
void BrowseTab.jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.forwardInternal(javax.servlet.ServletRequest, javax.servlet.http.HttpServletResponse)
boolean com.evermind.server.http.HttpRequestHandler.processRequest(com.evermind.server.ApplicationServerThread, com.evermind.server.http.EvermindHttpServletRequest, com.evermind.server.http.EvermindHttpServletResponse, java.io.InputStream, java.io.OutputStream, boolean)
void com.evermind.server.http.HttpRequestHandler.run(java.lang.Thread)
void com.evermind.util.ThreadPoolThread.run()Issue has been resolved .Ingnore this
-
Adobe Air error message when using PSE 10
When I try using the tips in PSE 10 I get an error message from Adobe Air stating that it is damaged. Have tried uninstalling and re-installing, but that hasn't helped. I have windows 7
Okay Jeff, this is as far as I have gotten so far. I'm using Air version 3.2.0.2070. This is the install log.
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -silent -eulaAccepted -programMenu AdobeHelp.air
Installed runtime (2.6.0.19120) located at C:\Program Files (x86)\Common Files\Adobe AIR
Invoking Application Installer for combined install
Launching subprocess with commandline C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp -silent -withRuntime -url -programMenu -eulaAccepted file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Application Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -runtime C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp -silent -withRuntime -url -programMenu -eulaAccepted file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Installed runtime (2.6.0.19120) located at C:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air to C:\Users\Vette\AppData\Local\Temp\flaE4EA.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla71A.tmp
Native installation package creation succeeded
Starting silent combined runtime update and app install.
Updating runtime from version 2.6.0.19120 to version 2.6.0.19140.
Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 to C:\Program Files (x86)\Adobe using the source file at file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Reinstalling C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp\setup.msi
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla71A.tmp\setup.msi with guid {BD7F1DA3-5EA0-65F8-52B0-5E103FDC045A}
Application Installer end with exit code 0
Subprocess app installer succeeded
Runtime Installer end with exit code 0
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -silent "E:\Adobe Photoshop Elements 10\AdobePhotoshopDotcomInspirationBrowser.air"
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Invoking Application Installer for combined install
Launching subprocess with commandline C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp -silent -withRuntime -url file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Application Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -runtime C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp -silent -withRuntime -url file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air to C:\Users\Vette\AppData\Local\Temp\fla634C.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'PhotoshopdotcomInspirationBrowser' and pubID '4C35C4D325D350FE0114230CBADCA2DDD0AC8D25.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla7325.tmp
Native installation package creation succeeded
Starting silent app installation to C:\Program Files (x86)\Adobe. Installing app PhotoshopdotcomInspirationBrowser.4C35C4D325D350FE0114230CBADCA2DDD0AC8D25.1 version 3.07 using the source file at file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla7325.tmp\setup.msi with guid {4C184855-B85A-6873-C642-60A58682E721}
Application Installer end with exit code 0
Subprocess app installer succeeded
Runtime Installer end with exit code 0
Launching subprocess with commandline C:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -updatecheck
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -updatecheck
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.6.0.19140/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.6.0.19140/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Unpackaging complete
Download success
Runtime updated downloaded
User has selected immediate install of the update
Starting runtime background update installation
Launching subprocess with commandline C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background\updater -update
Runtime updater successfully launched
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -update
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\airafa3.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_704_0 -ei
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Starting silent runtime update. Updating runtime from version 2.6.0.19140 to version 3.1.0.4880
Installing msi at c:\users\vette\appdata\local\temp\airafa3.tmp\setup.msi with guid {FE23D063-934D-4829-A0D8-00634CE79B4A}
Runtime Installer end with exit code 0
Elevated install completed
Runtime Installer end with exit code 0
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -updatecheck
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -updatecheck
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Clearing unused background update directory
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.1.0.4880/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.1.0.4880/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -arp:uninstall
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Runtime Installer end with exit code 6
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\aire7af.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_4784_0 -ei
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Starting silent runtime update. Updating runtime from version 3.1.0.4880 to version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\aire7af.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -arp:uninstall
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\program files (x86)\common files\adobe air\versions\1.0\resources\adobe air updater.exe -eu
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_3840_0 -eu
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Starting runtime uninstall. Uninstalling runtime version 3.2.0.2070
Uninstalling product with GUID {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
No installed runtime detected
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\airbda4.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_764_0 -ei
No installed runtime detected
Starting silent runtime install. Installing runtime version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\airbda4.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
No installed runtime detected
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\air2fa8.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_5396_0 -ei
No installed runtime detected
Starting silent runtime install. Installing runtime version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\air2fa8.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Application Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -playerVersion=11,2,202,233 -sandboxType=remote -securityDomain=airdownload.adobe.com -https=false -fromUserEvent=true -- -url http://www.adobe.com/support/chc/air/350/AdobeHelp.air -- WWW aHR0cDovL3d3dy5hZG9iZS5jb20vc3VwcG9ydC9jaGMv
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Begin air file download from http://www.adobe.com/support/chc/air/350/AdobeHelp.air
Download destination is C:\Users\Vette\AppData\Local\Temp\fla7A97.tmp
Received download status 200
Response URL is http://www.adobe.com/support/chc/air/350/AdobeHelp.air
Download success
Unpackaging file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp to C:\Users\Vette\AppData\Local\Temp\flaB22B.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\flaC7B.tmp
Native installation package creation succeeded
Starting app installation to C:\Program Files (x86)\Adobe. Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 using the source file at file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Got an unexpected fatal error while in stateInstalling: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="Unhandled exception Error: Directory can't be written to" errorID=5006]
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime "c:\Program Files (x86)\Common Files" -silent -logToStdout -url -location "C:\Program Files (x86)\Adobe" -desktopShortcut -programMenu file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Relaunching with elevation
Application Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_4952_0 -runtime "c:\Program Files (x86)\Common Files" -silent -logToStdout -url -location "C:\Program Files (x86)\Adobe" -desktopShortcut -programMenu file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp to C:\Users\Vette\AppData\Local\Temp\fla3260.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla3BF3.tmp
Native installation package creation succeeded
Starting silent app installation to C:\Program Files (x86)\Adobe. Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 using the source file at file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla3BF3.tmp\setup.msi with guid {BD7F1DA3-5EA0-65F8-52B0-5E103FDC045A}
Application Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline C:\Program Files (x86)\Adobe\Adobe Help\Adobe Help.exe
Application Installer end with exit code 0
Date: Thu, 12 Apr 2012 17:10:46 -0600
From: [email protected]
To: [email protected]
Subject: Adobe Air error message when using PSE 10
Re: Adobe Air error message when using PSE 10
created by Jeff A Wright in Downloading, Installing, Setting Up - View the full discussion
Vetteski65 I would recommend reviewing Troubleshoot AIR installation | Windows - http://helpx.adobe.com/air/kb/troubleshoot-air-installation-windows.ht ml for steps on how to resolve your difficulties. Please feel free to respond to this thread if you have any questions about the steps listed within the document. If you could also respond with the specific error message you receive it would be appreciated.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4331328#4331328
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4331328#4331328. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
Licence error message when using automation software
Error message when using Rational Functional Tester 7.0.1.1
to record a Flex application. The message seemed to come from the
Flex application.
I can record a fiew step in the application, then I have the
message : "Licence are not present. Eith the trial version only
limited record are allowed". But, my license of my Rational
Functional Tester application is activated.
I am using a Flex builder 3 trial version and the trial is
not over.
Is there any problem to get the license in the File compiler
with "D:\apps\IBM\SDP70\FunctionalTester\bin\rft.swc"? That RFT
file is supposed to be included in the flex application once
compileDoes anyone know how to build with automation support in a
linux environment?
We simply run an ant script build and have the SDK installed.
We purchased Flex Builder Professional, but cannot install on Linux
(we don't want to use the alpha version).
Thanks for any pointers :) -
I'm getting a error message when using Apple Configurator "unable to send ClearPasscode command to device"
Yes, that is correct. My spreadsheet has the following information in those cells if you want to compare yours on Monday:
Product Type
Application
|
AdamId:
<and a 9 digit number>
I ended up bringing the Macbook Pro home with me after struggling with it for a half hour at the end of a long day. I called and within 5 minutes the problem was corrected. The technician said they were getting calls all day. -
Since updating OS to Mountain Lion from leopard, I get the following error message when trying to backup with time machine on external drive. "Could not complete backup to media share. The network backup disk does not support the required AFP features." What are AFP features and how do I get Time Machine to backup to my current external backup?
This means that your NAS does not support the required encryption. Update your NAS to the latest firmware or ditch it and buy a Time Capsule (they are the most reliable when using TM).
-
F-04: give error message when clearing AP items with payment block key(R)
Hi all,
Customer wants to prevent payment for AP items with payment block key(BSEG-ZLSPR) .
I want system giving error message when doing payment clearning with t-code:F-04.
How can I realize it ?
Thanks Grus!
LynnPlease configure the following nodes properly:
Financial Accounting>>Accounts Receivable and Accounts Payable>>Business Transactions>>Outgoing Payments Global Settings>>Payment Block Reasons>>Define Payment Block Reasons & Define Default Values for Payment Block
For the error message: You may define a validation in OB28 with the help of ABAP consultant -
Error message when using Software Update
Hi everyone. I'm getting the following error message when trying to download some items via Software Update:
"None of the checked updates could be saved. A networking error has occurred: Cannot open file (-3001). Make sure you can connect to the Internet, then try again."
This is for the following downloads:
iPhoto 7.1.4
iDVD 7.0.2
iMovie 7.1.4
Security Update 2008-005
Any ideas? I have no problems with Internet access at all. I'm running a new 24" Intel iMac 3.06 GHz with Mac OS 10.5.4
Thanks for any help you can provide.
BruceHello b:
It sounds simplistic, but restart your computer if you have not already done so. I looked, but could not find that particular error code.
Barry -
Error Message When Using A.pack
I have a sequence that I exported out of FCP4.5 using compressor. It is about a two hour long movie and won't fit onto a dvd unless I use A.pack. I launch A.pack and make the settings and drop my AIFF files onto the two speakers and export. It gets about half way done and I get an error message that says "Mac OS has encountered a general error #1." I click OK and have to start over. Any ideas as to why this is happening? Thanks
Hi Tim,
Welcome aboard. This is an issue which was not rectified with dual processors until the DVDSP 4 release when Dolby encoding was moved to Compressor.
The simpliest form which has a good rate of success is set the encode going and don't touch anything until the encode finishes. This works well for most systems.
If you can't get this to work you will have to download CHUD from versiontracker. And disable one of your processors for the duration of the encoding.
Happy Camping -
Error message when using Spry Data set with XML
Hi,
I have what i see as a big problem, might just be me being
dumm, but here we go.
When I try to use the feature of spry XML Data Set and insert
spry table I get error message when trying it in IE 7.
There are even a problem when I use fireworks automated slide
show function, where you can choose to use the Spry/XML gallery
feature.
The error message I get everytime (incl the auto gallery in
fireworks) is:
The tag: "html" doesn't have an attribute: "xmlns:spry" in
currently active versions.[XHTML 1.0 transitional]
The tag: "div" doesn't have an attribute: "spry:region" in
currently active versions.[XHTML 1.0 transitional]
The tag: "th" doesn't have an attribute: "spry:sort" in
currently active versions.[XHTML 1.0 transitional]
and so on.
What´s wrong?!Hello barvid,
Ok, let's take each problem step by step:
1. The first error you see in the browser: " Exception while
loading ..." normally appears when you try to load files that are
not permitted by the browser security model. This means the XML
file you try to load is located on a different server than your
HTML which is not allowed. The browser is not permitting to load
any files that are not in the same domain as the current page
because of the complex security risks. You'll have to either get
the XML file from its original location and save it in your website
or use a proxy on your web server that should request that file
from the external server and send it to the browser as an XML from
the same domain as the HTML origin.
1.2 The "Exception while loading ..." error you see is a
generic error and my previous advise is based on my experience. In
case this is not your scenario you'll have to open the SpryData.js
and around line 112 you'll see the following code:
Spry.Debug.reportError("Exception caught while loading " +
url + ": " + e);
Please change this line with the following line of code:
Spry.Debug.reportError("Exception caught while loading " +
url + ": " + (e.message?e.message:e));
to obtain a more verbose error message that may clarify the
reasons of your errors.
2. The problems you describe are not browser errors but they
are w3c validation errors. At this point the XHTML standard allows
every application that define custom namespace attributes to also
link a DTD to the page so the page to continue to be valid.
Unfortunately at this point this feature is not correctly supported
by the FF and IE so we wrote an articles about how you should
link
the Spry DTD to your page so the validator understand the
custom attributes Spry use. You'll find inside the full description
of the problems and all the technical details you'll need to know
to solve this issue.
Regards,
Cristian
Maybe you are looking for
-
I bought a used ipod touch 4th gen. how do I add it to my account?
Hi I bought a used Ipod Touch (4th). It was wiped clean when I got it except it had the prev. owners apple Id still on it when we went to download an app.so I went in sign it out. then created a new acct with it under my apple Id. I have an Iphone 4
-
how can i see my contacts which i backup it on my PC ? so i go to i cloud and don't see my contact
-
Is it possible to share documents from Final cut pro x on my other mac?
is it possible to share documents from Final cut pro x on my other mac?
-
Hi. I have a strange problem that seems too unlikely to be pure coincidence. I have two double disk external enclosures connected via firewire, each set up as a software RAID 0 from disk utility. I keep one as a backup of the other. The other day, BO
-
My memory is full of "other" what files need to be deleted to free up more memory?
My memory is full of "other" what files need to be deleted to free up more memory?