Sb live 5.1 digital not found after reinstall of wi

hey,
im german so dont care for my english, and its new years eve :P
i have a problem: today i reinstalled winxp (installed no service packs or other things) and downloaded the newest driver for my sb li've 5. digital, but it says that no card can be found.
i read in the forum that a switch of the slot could help but it did not.
anyone who has an idea?
here some informations about my systemfrom aida32:
CPU Typ: AMD Athlon XP-A, 920 MHz (5.75 x 334) 2600+
Motherboard: Name: ASRock K7S8X (6 PCI, AGP, 3 DIMM, Audio, LAN)
Motherboard: Chipsatz: SiS 748
Soundkarte: Creative EMU0K SB Li've! Audio Processor (but the driver setup still says no card ^^)Message Edited by wave on 0-0-2006 06:50 PM

See if this CD hel
ps.
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=8432

Similar Messages

  • ITunes.exe - Entry Point Not Found after reinstall

    OK so I am using Windows XP, 32bit machine but it does 99% of my work
    Said yes to iTunes 12.1 update, iTunes nolonger runs on PC but pops up a warning window
    iTunes.exe - Entry Point Not Found
    The procedure entry point CMTimeConvertScale could not be located in the dynamic link library CoreMedia.dll
    OK'ing this
    produces new window: -
    iTunes was not installed correctly, Please reinstall iTunes
    error 7 (Windows error 127)
    Uninstalled iTunes 'only' from the Control Panel
    Reinstalled iTunes version 11.1.5 (Windows XP 32bit) which did run on PC
    Still see the same error. A bit stuffed as my music is in linbo.
    A fix would be wonderful.
    Thank you folks

    Entry point errors can often be fixed by deleting the offending dll, then repairing the component it is part of. CoreMedia.dll is part of Apple Application Support.
    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    If the advice above doesn't resolve things you could try this alternate version:
    iTunes 12.1.0.71 for Windows (64-bit - for older video cards) - itunes64setup.exe (2015-01-28)
    which is a 64-bit installer for the 32-bit version of the core application, similar to previous 64-bit releases.
    Or roll back to the previous build:
    iTunes 12.0.1.26 for Windows (32-bit) - iTunesSetup.exe (2014-10-16)
    iTunes 12.0.1.26 for Windows (64-bit) - iTunes64Setup.exe (2014-10-16)
    tt2

  • CS6 photoshop not found after downloading and putting in serial number

    CS6 photoshop not found after downloading and putting in valid serial number. Only extended version shows up as available. How do I just download CS6 photoshop only??
    Thanks!

    Nowhere during the installation does it give me the option to select the previous version I purchased! This is a new install on a new computer because my other computer no longer works. There is no option for me to select CS6 PS (NON EXTENDED) on the download from Adobe! When I install it only installs the extended version and tells me my serial number is valid but not for the extended. When you provided the link to the page that has the downloads, all that loads is the extended version. Can you please give me a link to the CS6 (not extended) so I can get back to work? I also was able to get the hard drive out of my computer that no longer works and put it on my new computer I'm trying to install CS6 on and the installer gave me NO OPTIONS to enter my old serial#.
    This is beyond frustrating!!!! I have a computer go out on me, and have to buy a new computer, then when I try to install CS6 PS it will not install. In the meantime I'm trying to keep my small business going to stay in business. I can't call any one from adobe. All I can do is send emails to get this resolved and wait.
    Please please help me!

  • Urgent 2nd request CS6 photoshop not found after downloading and putting in valid serial #

    CS6 photoshop not found after downloading and putting in valid serial number. Only extended version shows up as available. How do I just download CS6 photoshop only?? only the CS6 PS extended version shows up as downloaded.
    I have no idea how this forum works or weather or not this has been posted let alone answered. Can someone from Adobe please help me asap
    Thanks!

    check your duplicate post.  there are two responses.

  • "CJS-30199 The CTC classes were not found after waiting for 900 seconds."

    Here's the snippet of the sapinst_dev.log
    I am trying to install Central Instance on a RedHat Enterprise 4 server (32bit). But stuck at
    this stage.
    TRACE      [iaxxejsexp.cpp:188]
               EJS_Installer::writeTraceToLogBook()
    2007-05-10 20:19:48.093 FSPath(/usr/sap/LN1/DVEBMGS02/j2ee/cluster/server0/apps/sap.com/tclmctcutilbasic_ear/servlet_jsp/ctc/root/WEB-INF/classes/com/sap/ctc/util/ConfigMainExt.class).isExisting() done: false
    TRACE      [iaxxejsexp.cpp:188]
               EJS_Installer::writeTraceToLogBook()
    2007-05-10 20:19:48.093 NWJavaInstance._waitForFile() - elapsed time = 910 timeout = 900
    TRACE      [iaxxejsexp.cpp:188]
               EJS_Installer::writeTraceToLogBook()
    NWException thrown: nw.usageTypes.ctcSyncWaitTimeout:
    The CTC classes were not found after waiting for 900 seconds.
    ERROR      2007-05-10 20:19:48
               CJSlibModule::writeError_impl()
    CJS-30199  The CTC classes were not found after waiting for 900 seconds.
    TRACE      [iaxxejsbas.hpp:460]
               EJS_Base::dispatchFunctionCall()
    JS Callback has thrown unknown exception. Rethrowing.
    ERROR      2007-05-10 20:19:48 [iaxxgenimp.cpp:736]
               showDialog()
    FCO-00011  The step configCAF with step key |NW_Doublestack_CI|ind|ind|ind|ind|0|0|SAP_Software_Features_Configuration|ind|ind|ind|ind|15|0|NW_Usage_Types_Configuration_AS|ind|ind|ind|ind|0|0|NW_CONFIG_CAF|ind|ind|ind|ind|1|0|configCAF was executed with status ERROR .
    Your help is much appreciated.
    Thanks and Regards,
    Satish/

    Hello Satish
    Please do following checklist:
    1. Check that the J2EE engine is up and running (e.g. log in with Admin)
    2. Check that the following application is running:
         Visual Admin => Cluster => Server => Services => Deploy
         Select "Application" and look for "sap.com/tclmctcutilbasic_ear
    3. Try to continue installation
    It could be helpful to apply the patch for CTC as per note # 938261
    before restarting.
    and also try to add more memory allocation.
    If issue persists,
    - I'd like to know which installation DVD/CD number being using ?
    - The contents of the LABEL.ASC file.
    - The installation guide reference and title used for this install ?
    - SAPINST version ?
    - Oracle version/patch level ?
    - Operating system version/patch level ?
    See also:
    Note # 851251 - SAP NetWeaver 2004s Installation on UNIX
    Thanks
    Kenny

  • Error message of "404 - page not found" after downloading and installing Firefox 15

    Error message of "404 page not found" after downloading the latest version of Firefox.

    This sometimes is the result of firewall software protecting you from changed applications. Or it might be something else. Can you review this article and see whether it helps: [[Firefox can't load websites but other browsers can]].

  • Record drive/partition "500G Ext HD Western Digital" not found!

    I don't know why I'm getting this message when I open any songs I've recorded in Logic Express. It just started doing this today. Here is the message:{Record drive/partition “500G Ext HD Western Digital” not found!}
    I do not get this message when I open and work on songs I've recorded in Garageband.
    The 500G Ext HD is my external hard drive.
    Does anyone know what this means and how I can resolve it and get back to recording music??

    Does the disk appear OK on your desktop?
    When exactly do you get this message? When you double-click on a Logic file on your external drive? Or when you start a new project? Is your record path set properly in Logic?
    First, as you may be nearing a hard disk problem, make sure that all essential files are backed up properly.
    Then, open up your Disk Utility and run 'Verify Disk' and 'Repair permissions' on your external drive. If you have a copy of Disk warrior, even better.

  • My iTunes will not start.  The box on the error message APSDaemon.exe,  And message says "This application failed to start because MSVC80.dll was not found.  Reinstalling may fix."  I did the reinstall and I get the same error.

    My iTunes will not start.  The box on the error message APSDaemon.exe,  And message says "This application failed to start because MSVC80.dll was not found.  Reinstalling may fix."  I did the reinstall and I get the same error.  The error first happened after I approved the an iTurns update.

    Same problem today. Took five times to reinstall without any error messages. Apple has posted a way to fix and you should follow their's first. I finally got to upldate correctly by doing their fix but with one difference. I did the following:
    1) Went to the C:\program files (x86)\iTunes and C:\program files\iTunes folders and moved every file ending in .dll to the desktop (even if two files in same location had the same name, just replace)
    2) Restarted computer and still got error message
    3) Uninstalled all apple programs possible in the following order......itunes, apples software update, apple mobile device support, bonjour, and apple application support.....all performed using the microsoft control panel
    4) put all the .dll files on the desktop in the trash and emptied (this is a step apple support did not specifically put in their fix but for a final try I wanted to delete everything apple).
    5) Restarted computer.
    6) Re-installed itunes from apple website
    No error messages during re-install and was able to open shortcut in one try. Even updated my ipad to make sure everything was working.

  • Note pops up applicationfail to start ipworks6.dll was not found..reinstalling may fix problem..

    a note pops up saying..Application fail to start .. ipworks6.dll was not found..reinstalling may fix problem...
    == This happened ==
    Every time Firefox opened
    == after it was installed.. a week ago i switched ip's

    Try the following user tip:
    Troubleshooting issues with iTunes for Windows updates

  • I am trying to install itunes on my pc again but keep getting an error that says'apple application support was not found. try reinstalling itunes.' error 2

    I am trying to install itunes on my pc again but keep getting an error that says'apple application support was not found. try reinstalling itunes.' error 2.
    We have had itunes on this pc for 2 years and recently it wouldn't open and another error message kept popping up saying it couldn't open because MSVCR80.dll was missing. I have unistalled the apple programs and tried reinstalling several times but to no avail. Hopefully my music library is not gone. Any Ideas out there?

    With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
    Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
    http://www.apple.com/itunes/download/
    Download and install the free trial version of WinRAR:
    http://www.rarlab.com/
    Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
    Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
    Does it install properly for you?
    If instead you get an error message during the install, let us know what it says. (Precise text, please.)

  • I had itunes installed on my pc. I received notice to update. I started update but gpt the following message - this application failed to start because MSVCR80.dll was not found. Reinstalling may fix the problem. I uninstalled and have tried to reinstall

    I already had itunes installed on my pc. I received an update and tried to install it. I got a message
    This application failed to start because MSVCR80.dll was not found. Reinstalling may fix the problem.
    I uninstalled itunes and tried to reinstall. itunes says it has installed but when I try to open itunes I get the same message.
    How do I repair/sort out this error/fault
    Thanks
    David

    Try the following user tip:
    Troubleshooting issues with iTunes for Windows updates

  • TS3212 I cannot get the new iTunes to start in Windows Vista. I get an error that states "This application has failed to start because MSVCR80.dll was not found". Reinstalling does not help.

    I get an error that states "This application has failed to start because MSVCR80.dll was not found". Reinstalling does not help.I have tried removing iTunes and reinstalling, I have tried "repairing" option at reinstall, nothing seems to work.

    Read this:
    iTunes 11.1.4 for Windows - Unable to install or open - MSVCR80 issue

  • When trying to launch ITunes I get an error message saying that application fail to start because MSVCR80.dll file not found. Reinstalling app may fix problem.

    When trying to launch ITunes I get an error message saying that application fail to start because MSVCR80.dll file not found. Reinstalling app may fix problem.

    I've just (finally) managed to fix this problem today. I checked the Apple Support forums, and it seems a lot of people are having the same problem.
    I rang the Apple Support line, and the very helpful man (thanks Alan!) talked me through it stage by stage. If you go to the following page on the internet: http://support.apple.com/kb/TS5376   it takes you through the process. WARNING - it takes a little time!
    Basically, the first thing you have to do is go to your Program Files and double click on your iTunes folder. There'll be a number of files with the suffix .dll - you need to move all the .dll files from that folder to your desktop - you can simply click and drag them on the desktop..
    Next, uninstall iTunes - go to Control Panel / Add/Rempve Programs and when the list comes up remove iTunes. This will take a few minutes... Then reboot your computer.
    Next, go back to Control Panel / Add Remove and Remove - IN THIS ORDER -
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support
    Reboot again!
    Next, check in your Program Files that the iTunes folder is completely gone - if it has, great: if it hasn't, right-click on the folder and press Shift and Delete - it will say "Are you sure you want to completely remove the folder "iTunes"? Click on "Yes".
    Reboot!
    Then go to the iTunes download page and voila! It should download iTunes without any problems... well it did for me.... Good luck!

  • My computer continues to say xvi.dll was not found. Reinstalling may fix the problem what to do?

    my computer continues to say xvi.dll was not found. Reinstalling may fix the problem what to ?

    Try the following user tip:
    Troubleshooting issues with iTunes for Windows updates

  • "Hard Disk - (3F0) BootDevice not found" after removing Windows

    Hi.
    I own a ProBook 4530s that came with preinstalled Windows 7 Home Premium. I'm a long-time Linux user, so the first step I took after buying it was shrinking the OS partition and installing Arch Linux on the newly created free space. I have used the notebook in this setup for something like a year now, but since I rarely even boot to Windows, I decided to gain some free space by deleting them entirely. Using cfdisk, I deleted their partitions.
    After a short time (about a day), I had the machine powered down, and I found some old labelless CD I wanted to inspect. I started the computed and inserted it into the drive. It was apparent it was a Windows XP installation CD, so I turned the computer off (before it finished the phase of loading drivers).
    (It's likely that the previous paragraph is unrelated to the error message, because the installation shouldn't even touch the disk at that phase. I also don't reboot often, so I'm not sure whether did the computer boot between deleting the partition and booting the Windows XP CD.)
    The next time I tried to boot the PC, I was greeted with "Hard Disk - (3F0) BootDevice not found". All HP diagnostics were OK, and when I instructed the GRUB on an Ubuntu live CD to boot into my hard drive, it booted normally.
    I admit the BIOS might be somehow confused by the partition table I have, as it begins with a lot of free space and has no NTFS partitions, but I believe BIOSes shouldn't be dependent on the OS I run. So, I have a few questions:
    Does the HP BIOS try to detect Windows, and does it do anything differently if it doesn't find Windows on the hard drive? I googled around, and didn't find anyone with experiences running just Linux on my notebook (just dual-booting...).
    If it does, is there some way I could convince it to boot into the hard drive even through it doesn't have Windows on it?
    Thanks.
    This question was solved.
    View Solution.

    I see the same error but my situation still allows me to boot up but only with the secondary HDD in the DVD writer bay. For more details, please see an existing thread on http://h30434.www3.hp.com/t5/Notebook-Hardware/Hard-Disk-3F0/m-p/1670523#M76013.
    I am suspecting that it has something to do with BIOS not reading the MBR or something.
    Have you sorted your issue on this yet?
    Cheers

Maybe you are looking for

  • Export to flat file with unicode (chinese) characters??

    I have an SSIS (2013) package that needs to send an email notification with query results (via attachment). I have a data flow task with a source sql query that gathers 2 columns - ID and NAME. ID is varchar, NAME is nvarchar (some records have Chine

  • Import memory id

    Hi i need to import memory ID weather i need to declare the same structure for importing the memory id or same structure with different names because i am downloading the memory ID from a query report if i declare the same structure in the programe i

  • CSV export problem with multiple pages

    I have a simple report with pagination and export to excel enabled. If I paginate from page 1, without exporting to excel, to any other page, then export to Excel, I get "No data found." in the CSV output file. If I export from Page 1 first, then the

  • Mail adapter - SCOT needed ?

    Hi guys, I've done the proper configuration of an ABAP application system's target SMTP server (in SCOT), however I am curious is it a must for using successfully the Mail adapter..? Thanks & Best Regards, Lalo

  • Help with i photo

    Hi there. I recently bought a mac (first one) i don't seem to have iphoto there is a question mark over the icon on bottom tool bar does this mean i haven't installed it?