SB X-Fi Titanium Front Panel not working

Hello,
I would like to fully use the Front Panel, because I own a 5. Surround sound system blocking all the backpanel slots. The problem is, that I simply get no sound from the front panel sound output, while the microfone works just fine. Is there some kind of special option to enable it's
The FP is properly plugged into my SB X-Fi Titanium. And it's also not broken, because the FP works perfectly with my onboard soundchip (though it seems to cause crackling in my headphones, so I cannot use it for it).
... Okay now the Mic FP is not working aswell, eventhough it did when I tried it the last time. I set everything I could, like choosing Headphone Mode, enabling FrontPanel everywhere and all that. So why is it still not working?
RIG: Win XP 32bit
Asus P7p55d
Creative SB X-Fi Titanium
normal Stereo Headset
Thanks in advance for any help!

Ofcourse that was something I did not know before I bought the soundcard. I am quite sure it is an AC 97 Front Panel, but how can I verify that?
Seems like I will have to sell this soundcard.
- The plugs from my 5.1 sound system are quality plugs and are rather big and so they barely fit, because the audio jacks (not sure about the correct english term here, i mean the holes from the soundcard, where you plugin the soundsystem) are sitting way too close together (expected more for that price..).
- It doesn't support my Case's Front Panel.
- And the soundcard is sitting directly before my Graphic Card's fan (because it uses PCI-E), causing heat.
I guess there is no way around it. I will probably get a new graphic card at christmas and it's most likely going to be bigger than my ATI 4850HD. And I simply do not have the space for a bigger graphic card AND a soundcard, that uses PCI-E. So I guess the best solution is to sell it and buy a soundcard that uses normal PCI and supports AC 97, right? Or what would you recommend?
Until then, is there an easy and cheap way to upgrade my ac97 front panel to Intel HD Front Panel Audio?
thanks

Similar Messages

Sound Blaster X-FI Pci Express Front Panel Not working right Win7

ASound Blaster X-FI Pci Express Front Panel Not working right Win7
Please read carefully
Part number Part SB040
Hello,
I have a fresh install of Win7x64 OEM. First, I want to say that I have "AUTOMATICALLY MUTE SPEAKERS" UNCHECKED under the Headphone detection tab. I have tried "Automatically Enable Headphone Settings" checked or unchecked. No difference.
As soon as I plug in headphones to the front panel connector , the speakers in the mixer say "disconnected" (see below) and the SPDIF becomes the default output. There is no way for me to change this. And there isn't any sound coming from the headphones when plugged into the front panel. (the mic front panel works fine)
I am using the nati've Win7 drivers for the card. Apparently the Win 7 drivers on your site are older than the nati've ones.
This worked fine in Windows XP 32. Any ideas.

Ok guys this is how I fixed the problem on my X-Fi PCI-Express. Open the Creative SB X-Fi Volume panel. Mine is set in game mode and I have 5 vertical sliders for Line-In /Mic, MIDI Synth, Digital-In, and the last one will say one of three things either Digital-In, Microphone, or Mirophone FP. At the top of the?slider there is a tab which brings up a drop down menu. Mine was default set to Digital-In, I switched it to Mirophone FP (tried Microphone first and it worked but the FP sounds better for me) and cranked it all the way up and my problem was solved. Very frustrating one though as there is no documentation that led me to the fix it was just playing around with it till I could figure it out.
I hope this at least helps some of you out.

Audigy SB 2 ZS Platinum Front Panel not working-HELP

Hey everybody. I'm new to this forum, but not to computers. I built my computer about 4-5 months ago, and here are my specs:
Ultra MS Blue Dragon
ASUS P5GD
Intel P4 Processor 3.0GHz
GB GeIL RAM
6600 GT 28MB Video Card
Samsung 20GB SATA HDD
Lite-On and NEC DVD Dri'ves
Ultra X-Connect 500 W PSU
Creative SB Audigy 2ZS Platinum
I got the 2ZS platinum from a friend, but I already had a regular 2ZS. I plugged in his front panel to my old 2ZS. The front panel did not work. I then got his 2ZS, just the sound card, and plugged in the front panel. It still did not work. I installed all the software and drivers, and nothing. My sound card works fine, it is just the front panel that doesnt work. Does anyone have any ideas?
Thanks a ton,
Derek
P.S. The AD_EXT Cable fell apart a couple of times, but we put it back together. Could that be a problem? If so, where can I get a new AD_EXT Cable?

ttt

MSI 180 front panel not working in both modes

hi,
I bought a msi mega 180 with AMD cpu, works quite nice for a barebone
Now the problem is the front panel doesn't work anymore. It worked before, but now it doesn't work anymore. I think nothing is changed.
I thougt the panel was broken, so I replaced it by a new version at an officiele msi distributor in NL, I placed the new panel. But nothing happened on that panel, on pc and hifi mode.
So I think the barebone is broken, anyone can tell what to try before I can conclude the barebone (motherboard) is broken?
btw, it's connected by 2 connectors, 1 looks like an audo connector the other one looks like a normal connector to me.

Hi,
I don’t think the front panel or the main board is broken I think its something else we haven’t figured out and MSI not willing to help us... I have Mega 865 and I have been having the same problem for almost 3 weeks now... sometimes it works and sometimes it doesn’t in both modes everything else will work normal except LCM.
Once it works will work perfectly until I unplug the power from the computer then LCM display will not start.
The problem begins when a hardware is installed the first time to get the problem I had just installed a pinnacle TV tuner when I took it off it came back the second time i installed a DVD rom but when I took it out still didn’t work I removed almost everything checked all cables and changed memory couldn’t get it work then I decided to put back everything TV card, DVD-rom, same memory back and still didn’t. Since it had happened before i was not convinced that it was broken then the second day I put the computer on and it worked on its own.. Now it works when ever it feels for it and take the day whenever.
Let me know if you find anything helpful.

Japanese font on Front Panel not working

Hi,
I am new on using LV and finds out that whenever I type a Japanese character, it shows garbage text.
System:
Windows 7 Pro 32bit SP1
Labview 2013
Problem:
Whenever I key in Japanese character, the result is garbage, however when I tried to export the VI, and when I opened the txt file, the character is written correctly.
Seems like only in the front panel the characters are displaying incorrectly.
I've attached the Locale settings and also the garbage in the front panel for reference, as well as the printscreen of the export txt.
Any solution for this one?
Solved!
Go to Solution.
Attachments:
Locale.png ‏34 KB
Garbage.png ‏5 KB
Exported.png ‏26 KB

Hi,
There are several ways to display foreign languages in LabVIEW front panel.
1. set “UseUnicode=True” in the LabVIEW.ini file.
2. use the app locale utility from Microsoft (http://www.microsoft.com/en-us/download/details.aspx?id=13209). With this tool you can run LabVIEW (or builded app) under different locales without changing system locale in Control Panel.
3. By default UseUnicode in the LabVIEW.ini file is disabled. Remove it or make it False if you've added the UseUnicode.
Then go to control panel>> Region and Language >> Administrative tab. Then in language from non-Unicode programs, select the language you want to use. With UseUnicode False, Windows will see LabVIEW and a non-Unicode program and enable this feature.
Maybe you can refer to the links below.
http://forums.ni.com/t5/LabVIEW/Doug-s-first-nugget-Unicode/m-p/2052682
https://decibel.ni.com/content/docs/DOC-10153
Hope this helps.
Warmest Regards,
Rebecca
Applications Engineer

Audigy 2 card with Audigy Front Panel not worki

I've just bought a used audigy 2 card with an audigy front panel. I have installed everything and have sound from the card to my speakers.
The front panel has a blinking light on the optical out and when I plug headphones into the panel, I can hear static and control the volume of the static from the knob on the panel.
I can't hear anything else through the headphone jack and can't get any input signal using the line 2 input on the front panel.
Connections and drivers appear to be OK, am I missing something......
Thanks,Dave.

David,
If you go into the surround mixer or Windows mixer do you see a listing for the front panel inputs (line in2/mic in2, Aux 2, etc)? If so, are any of them muted? If you go to start/programs/Creative/SB Audigy/Audio HQ/Device Settings, do you show a headphone tab? If so what options are enabled in there?
Double check your ribbon cable connection and maybe even swap sides of the cable.
Jeremy

Simultaneously Controlling LabVIEW Remote Front Panels not working properly

We are trying to simultaneously control a Executable file from different PC as per the description given in link below:
http://www.ni.com/white-paper/4867/en
But the issue is that we are not able to view it in Web browser as in "Web Publishing tool" When we click on "Preview in Browser" it Pop up a message " Web server not started. Do you want to start it now? We Click YES. Still nothing happens.
We have exactly followed the steps given in the "white-paper/4867/en i.e. Selected "Enable web server" and VI Properties to "Reentrant execution".
In Control Panel>>Administrative Tools>> Services we found that NI Web Server is available but NI Application Server is not installed. Is this is the reason why we are not able to Preview in Browser. If yes how to install that OR any thing else we are missing?
Thanks
R.B.Chavan

Mateus23 wrote:
I'm now developing the web version in HTML 5, using web services to comunicate with my labview application.
There you go, good solution. When doing this remember that you have access to the database on the server. A structure I have found effective is to use the server DB like a dropbox that I write to, and the web server reads from.
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

Audigy 2 platinum front panel not working!!!!!!

I have sound through desktop speakers through the back of the sound card(that works). I had to reinstall the drivers to get that to work. Best buy reinstalled the stuff a week ago so i think the internal stuff is correct. The headphones dont even get static on the front, and it wont read mics. Ive downloaded the lastest drivers, checked to see if stuff was muted. Did i miss a step or is the front just dead. Im recording soom vocals for a band audution and need this working really soon. Please for the love of god help.!!

Actually I'm having the same problem too here.
Did all the troubleshooting I could the only thing left is to test the AD_EXT cable.
Anyone able to give some advise on this?

Front case audio panel not working

I just bought a new case but the microphone and phones connectors at front are not working...
I know I have to connect them to the motherboard but I don't know if 'ts corretly connected cuz the names on the board manual are different from the ones in the case.
Here are the names in case:
MIC VCC
MIC DATA
GND
EAR R (x2)
EAR L (x2)
The connector on the board is something like this:
| 9|7|5|3|1|
|10|8|6|4|2|
and the board manul as this on it:
PIN SIGNAL DESCRIPTION
1 AUD_MIC Front panel microphone input signal
2 AUD_GND Ground used by analog audio circuits
3 AUD_MIC_BIAS Microphone power
4 AUD_VCC Filtered +5V used by analog audio circuits
5 AUD_FPOUT_R Right channel audio signal to front panel
6 AUD_RET_R Right channel audio signal return from front panel
7 HP_ON Reserved for future use to control headphone amplifier
8 KEY No pin
9 AUD_FPOUT_L Left channel audio signal to front panel
10 AUD_RET_L Left channel audio signal return from front panel
This is how I have connected:
MIC VCC -> 3
MIC DATA -> 1
GND -> 2
EAR R (x2) -> 5&6
EAR L (x2) -> 9&10
It's wrong right? Help...

I had the same proble double checked all the connections 20 times then I found the problem in software...
Look in the volume control panel for an option to enable the front jack. You will have to enable advanced controls. Then click the advanced button and check the mic2 select box.
if that does not fix it for you try this
MIC VCC -> 3
MIC DATA -> 1
GND -> 2
EAR R (x2) -> 5&6 reverse these (one should say out on it, out should be on 5)
EAR L (x2) -> 9&10 reverse these (out on 9 here)
My antec case came nicely labled for me with a thick manual featuring translations of their pin labels to the proper locations. Also It has a standard intel 10 pin connector AND the 7 individual wires if needed... handy huh.
Get a good case. But good luck.

Front audio panel not working on K9N Neo V3

A new problem with MSI K9N Neo V3 MB...
I just found out that Front audio panel is not working (no mic, no line out). I checked the cable 3 times. Seems to be OK. Front panel was working on a previous ASUS motherboard.
- All drivers according to vista are working fine.
- Back panel sound (eveything) is working fine.
- Sound panel says that front panel mic & line-out are not plugged in.
Is there a switch to turn this on? Or maybe some special driver?
Or it is just useless, and working on MB package advertisment only?

Quote from: Richard on 13-January-08, 06:50:13
P.S. Just a thought, I could go get a Ouija Board or Dart Board if you prefer. Might yield some answers.
You sure are funny. No doubt about that.
I do appreciate a good laugh, but in this case laughter won't solve my problem.
This little analogy with a car and a tire is just ridiculous. You know, tire is flat or it is not. Or is it maybe flat only on BMW cars?
I see no purpose in describing cables here, but if this is what would make you happy... It happens that I have few spare mintues, so here we go.
chapter 1. - The Case
I do not know what brand is my case. It's a cheap case with expensive Corsair 550W PSU. Very well cooled. I also don't know what is its name, so let us just call it George.
Here is George roaring on my desk;
Chapter 2. - Jimmy & Gina
This is an unknown brand, no name Front panel cable so let's just call it One eyed Jimmy;
This is local one tooth missing whore called Gina;
Chapter 3. - Encounter 1
Jimmy fills Gina just right. It's very tight but just right;
Chapter 4. - Berta, Gertruda and Mike
Dirty Twins Berta and Gertruda are ready to recieve some massive waves;
Big Mike is ready to give:
Chapter 5. - Encounter 2
It fits right again:
Chapter 6. - Oh NO!!!
It's not working on MSI AGAIN:

HP 6500 wireless ALL-in-one e709n Printer front panel not responding at all

Hi there,
I have got a HP 6500 wireless ALL-in-one e709n printer.
I have been using it with my pc with windows vista on it for nearly 2 years and it has been great.
1 month ago, the front panel of the printer stopped responding, ie, when i press any buttons, the lcd screen on the printer does not change, it always show the ink level.
The printer turns on, shows that its preparing, then goes to idle state with ink level icons on the screen.
If i try to print any documents, it works with ethernet cable connected to my pc (which i used to do it wirelessly) , the cable-connected printing function still works, but wireless printing does not work anymore.
However if i try to scan something, on the pc when i open the hp scan app, it shows that 'scanner is not available'.
Also because the front panel doesnt work, no buttons respond, i cannot scan or copy.
I have tried unplug everything and reinstall all drivers and programs.
No damage to printer or my pc, it just stopped working all the sudden.
Can any one help me out please?
cheers,
Charlie

Hi Charlie,
Try going throgh the steps listed below and check if that may help:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02716803&cc=us&dlc=en&lc=en&product=3795406&tmp...
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Midi in from front panel stopped working (x-fi platinum)

8midi in from front panel stopped working (x-fi platinum)" Not sure if I burned the connector or if something is wrong with the driver. My midikeyboard can't be used with sb x-fi platinum anymore.
I borrowed terratec soundcard from big brother a while and used my midikeybaord in with that and output with x-fi card. but now he's taken the terratec back.
and I'd like to really know what's wrong witht he midi in.
Does anyone know what might be the problem?
I have connected normal midi cable -> normalmidi to tiny x-fi port convertor -> front panel
This used to work a bunch of months ago.
i'm using winxp latest updates. i'm trying out reaper. I've got asio4all installed but i usually use directsound when I'm composing music.
tahnks for any help

i have the exact same problem with vista!!!no sound from the front panel of x-fi platinum!i don't know what to do!

Soundblaster X-Fi Titanium Optical Out not working???

Hey friends,
I purchased a Sound Blaster X-Fi Titanium PCIe yesterday to run on Windows 7 64bit to trigger VSTi instruments. I can hear the VSTi play fine when I have headphones plugged into the soundcard but I want to send the audio sound OUT via the Optical Out into my Steinberg MR86x firewire audio card. ?
I can see the light on the optical cable but no sound seems to be being sent from the sound blaster into the steinberg card.
?Now before people start saying you cant do that, I have have been doing this for the last 3 years and it has been great apart from my RME Audio card is not compatible with Windows 7 64bit hence why I purchased the soundblaster.
I really am at a loss as to what I can try next, I have been through this forum and tried a few recommended tweaks but nothing? Am I missing something obvious here?
I am using the following drivers
Driver: v2.7.008 Windows 7 64bit
DTS Connect: for Windows 7 64bit
Also in the Audio Control Panel / SPDIF I/O all options are greyed out apart from the Digital Output tickbox, I only want to use this card for Audio as in creating music or specifically for triggering VST synths.
I would really appreciate any advice
Thanks in advance
KiloHurtz

Re: Soundblaster X-Fi Titanium Optical Out not working?I have same card, same?OS?and lots of problems.
Analog outputs(control panel->sound->speakers) disappears when boot or reboot, sometimes it works week, sometimes a hours. When it works, it's works ok, but suddenly during boot,?all sounds is lost, when trying launch for example Creative Audio Control Panel this message appears: There are no supported audio device available. You need to close the application. Click OK to close the application now.
And when analog outputs disappears, no any sound via SPDIF, even it shows in notification area and control panel->sound and in device manager.
I have owned card about two months, once change card in warranty, and?several uninstall, cleaning traces, reinstall and card works for while?and?out of blue, when boot computer, no sounds at all and only way to get sounds back is driver uninstall, cleaning and reinstall.
Creative Customer Support seems to be clueless, but make Technical Support Request if problems continue. And all other too, if problems like that appears, contact to Creative, maybe they really try?to do?something abuot it and not just send instructions how to uninstall and reinstall drivers.

Iphone 6 plus front camera not working in whatsapp

iphone 6 plus 64GB iOS 8.1 front camera not working in whatsapp

It seems the facetime camera does not work for whatsapp only it works normally.

Anchor links to accordion panels not working properly across browsers

Hi everyone,
I need some help to figure out why my anchor links to specific accordion panels on another page are not working properly across browsers.
I have a Map page which has tooltips on mouseover on the site markers. 15 of the tooltips have "Click here for information" anchor links (although only 14 are currently linked) which, in theory, would take you to the Nurseries page where the specified accordion panel would be opened with the nursery entry appearing at the top of the new browser window.
Here are the links to the Map page and Nurseries page, respectively:
www.alegriadesignstudio.com/RFRI/map_v6.html
www.alegriadesignstudio.com/RFRI/nurseries_v6.html
I've tested the anchor links on IE, Firefox, Google Chrome, and Safari, and have received varying results. In most cases, the anchor links worked perfectly on two of the browsers, while on the other browsers, the correct accordion panel is opened but the nursery entry does not appear at the top of the new browser window. Anchor links using Safari and Google Chrome fared better (10 out of 14 links worked properly, and 8/14, respectively), whereas when using Firefox and IE, only 3 anchor links worked properly. The target audience for this website will be using IE and Firefox, so I would appreciate any help to figure out how to tweak the code so that the most, if not all, anchor links work properly on these two browsers in particular.
Here's an anchor link which worked perfectly in IE, GC, and Safari, but in FF, the entry did not appear at the top of the new browser window.
www.alegriadesignstudio.com/RFRI/nurseries_v6.html?luzon=9#mangatarem
http://www.alegriadesignstudio.com/RFRI/nurseries_v6.html?luzon=9#mangatarem [To access the anchor link on the Map page, mouseover the third green dot from the top of the map (Tooltip--Location: Mangatarem) and then click on "Click here for information."]
Here's a sample anchor link in which the entry did not appear at the top of the new browser window in any of the 4 browsers:
www.alegriadesignstudio.com/RFRI/nurseries_v6.html?mindanao=4#magpetAmabel
http://http://www.alegriadesignstudio.com/RFRI/nurseries_v6.html?mindanao=4#magpetAmabel [To access the anchor link on the Map page, go to "Mindanao" at the bottom of the map and mouseover the fourth green dot below the word "Mindanao" (Tooltip--LOCATION: Brgys. Amabel, Bongolanon, Imamaling, & Manobisa; Magpet; North Cotabato) and then click on "Click here for information."]
Here's a sample anchor link in which the anchor link worked properly in GC and Safari, but the entry didn't appear at the top of the browser window in IE and FF:
www.alegriadesignstudio.com/RFRI/nurseries_v6.html?visayas=1#bilar
http://http://www.alegriadesignstudio.com/RFRI/nurseries_v6.html?visayas=1#bilar [To access the anchor link on the Map page, go to the small island north and a bit west of "Mindanao" which is called "Bohol" and mouseover the fourth green dot below the word "Mindanao" (Tooltip--LOCATION: Bilar; Bohol) and then click on the first "Click here for information."]
Many thanks in advance for your assistance!
Joy

Hi everyone,
I'm still trying to figure out how to resolve the problem of anchor links to accordion panels not working properly across browsers (see original post for details). I would greatly appreciate any suggestions on how to resolve the problem.
Many thanks in advance.
Joy

SB X-Fi Titanium Front Panel not working

Similar Messages

Maybe you are looking for