SB0358 and the Digital I/O mod

Will the digital i/o module work on the Audigy 2 ZS that comes with the Dell (see subject for product code). I just set up a 65" plasma and want to connect my computer via coaxial or optical to my sound system. I just picked up the Yamaha RX-Z9 and want the best possible sound. But on the web page it states that it will not work with any other card. I figure that this is a value card as it is sold with the Dell, but would like to make sure before buying the $5 device and then not being able to return it.
Thanks,
Mario

marioa35 wrote:
Will the digital i/o module work on the Audigy 2 ZS that comes with the Dell (see subject for product code)...
This is where you said that you have ZS Dell if you don't remember. I have checked the knowledgedatabase here: http://dmzweb3.europe.creative.com/w...list_audio.htm and your statement about the card type was true.
Then I have checked the Digital I/O requirements http://us.creative.com/products/prod...55&product=780 and there was stated:
Works with the following Sound Blaster cards:Sound Blaster? X-Fi?, Sound Blaster? Audigy? 4, Sound Blaster? Audigy? 2 Value, Sound Blaster? Audigy? SE and Sound Blaster? Li've!? 24 bit
So your card wasn't on the I/O lis of compatible cards.All this took 3 minutes, not 4 hours like you said. You are upset because I asked if you bothered to check the basic facts like this before you come and ask the question? Especially when 2 posts down from yours (at the moment of posting) was the same question? To bad... I told you the answer, but I am not paid to be "nice" to you.
Then you decide that my tone is "condescending" and "against the rules"... I bet you didn't read the rules either. How about your comment about my spelling? How you call that?
Since you have trouble spelling I will wait for a better answer.
Anyway good luck with finding help in life if this is how you react.
Message Edited by SoNic2367 on 09-2-2006 06:29 AM

Similar Messages

XBOX 360 and the Digital I/O Mod

Hi everyone and first of all thank you for your time. The problem is pretty simple, I get no sound no matter what. :smileytongue:?I looked around in the forums and the only thread I found relating to this are concerns about the DTS capabilities and such. Everyone claims to have sound using the Digital Stereo setting in their XBOX well this doesn't work for me. I saw a few places where they sugested to unmute certain option in windows and I belei've I unmuted everything... I am not very good with the audio aspect of computers so I took a few screenshots to help you help me. :smileyvery-happy:?Just incase?I tried the red and the white wire on numerous occasion (because honestly I have no clue which one is the right one) and I never managed to get anything out of it... please help me!!! ?[img"]http://i84.photobucket.com/albums/k2/sinoir/creative_console02.jpg">[img"]http://i84.photobucket.com/albums/k2/sinoir/creative_console0.jpg">[img"]http://i84.photobucket.com/albums/k2/sinoir/audio_conole.jpg">[img"]http://i84.photobucket.com/albums/k2/sinoir/windows_option.jpg">

marioa35 wrote:
Will the digital i/o module work on the Audigy 2 ZS that comes with the Dell (see subject for product code)...
This is where you said that you have ZS Dell if you don't remember. I have checked the knowledgedatabase here: http://dmzweb3.europe.creative.com/w...list_audio.htm and your statement about the card type was true.
Then I have checked the Digital I/O requirements http://us.creative.com/products/prod...55&product=780 and there was stated:
Works with the following Sound Blaster cards:Sound Blaster? X-Fi?, Sound Blaster? Audigy? 4, Sound Blaster? Audigy? 2 Value, Sound Blaster? Audigy? SE and Sound Blaster? Li've!? 24 bit
So your card wasn't on the I/O lis of compatible cards.All this took 3 minutes, not 4 hours like you said. You are upset because I asked if you bothered to check the basic facts like this before you come and ask the question? Especially when 2 posts down from yours (at the moment of posting) was the same question? To bad... I told you the answer, but I am not paid to be "nice" to you.
Then you decide that my tone is "condescending" and "against the rules"... I bet you didn't read the rules either. How about your comment about my spelling? How you call that?
Since you have trouble spelling I will wait for a better answer.
Anyway good luck with finding help in life if this is how you react.
Message Edited by SoNic2367 on 09-2-2006 06:29 AM

HT201306 I bought an album on iTunes and the digital booklet it came with is not in my iTunes library. How can I get it back?

I bought an album on iTunes and the digital booklet it came with is not in my iTunes library. How can I get it back?

You could try emailing iTunes support, giving them your order number, etc. or you could just take the hit and pay the 99p. I know what I would do.

I have upgraded to latest IOS 7 software and the vibration on silent mode does not last long enough

I have upgraded to latest IOS 7 software and the vibration on silent mode does not last long enough

I think you're using a Lion developer version. Open  > About this Mac > More Info, and copy Software here. Did you purchase Lion in the App Store?

Acrobat 9 Standard and the Digital Signature usage right

Acrobat 9 Standard is apparently able to apply certain usage rights to a document. I am trying to confirm whether or not the digital signature usage right is included. The
Acrobat 9 product comparison seems to indicate it is not, but the online help implies that it is.
Can someone with Acrobat 9 Standard confirm this for me by testing a document that you've enabled for use with Reader by attempting to sign a digital signature field with Reader?
George

In the office area, the Pro version might be good to have for the forms and other features. For the general library, Reader is probably adequate. Actually allowing PDF creation on public machines can be an issue. In a small libary system, Acrobat might be reasonable where you do not have to deal with a large, diverse population. However, for basic PDF creation, only Std is needed. Having both AA8 and AA9 on the same machine can lead to problems. However, if you remove one, you will likely have to repair the other.
The problem with older versions is that they may not properly read some of the newer PDFs that might be downloaded. For the latter, you could install the latest version of Reader, but you need to be aware that you may have to deal with issues of right clicking (windows) on a file and selecting which application to open a PDF with. For forms and some editing, the Pro version would be good to have. You also have PDF Optimize and PreFlight with the Pro version that generally are not including in the Std version.
To help compatibility with the files you create, you can select Start>Printers>Adobe PDF preferences (right click on printer). In the settings tab>Default settings> select at least Std or better Press or Print and then push edit. Under the general tab select the compatibility and set it to AA8 so that every thing is compatibile with the oldest version of Acrobat you have.
If you have more than one computer in the office, you might consider having AA8 on one and AA9 on the other. Do check and be sure you have licenses for whatever you have and that someone has not come in and installed a pirated version. Also be sure you keep the original CDs and licenses (or if they were downloaded, burn the downloaded version to a CD as an archive and write the SN on the label).
Now that I have confused you, are there more questions?

HT203433 I bought a cd today, and the digital booklet came with it, (Of course). But when I click on the digital booklet, it opens up in Microsoft Words with no pics/lyrics/artwork. Instead, I get like 200 pages of a bunch of Gibberish letters/symbols :

Anyone else have this problem and know how to fix it???
Please and thank you, in advance
It's not on iPod, it's on the computer labtop that this is happening. Figured it prob wouldn't work on an iPod

Hello fellow iTunes users. My issue is related to the one above.
I can successfully download the digital booklet included with Taylor Swift's Red Deluxe album, but when I try to open it in Adobe Reader (and the pdf reader included with Windows 8), the following error screen appears:
I have tried to re-download the file several times - and on a different computer. Is Apple aware of this issue and, if so, is there a fix for it? Both are using Windows x64 versions. One is running Windows 7, the other running (the truly awful) Windows 8.
Many thanks.
p.s. I upgraded to iTunes 11 before this purchase and I find iTunes 11 to be a marked improvement on v10 and the only reliable media player that I am able to use on Windows 8, so congratulations Apple for doing a better job than Microsoft when it comes to Windows 8 compatibility, lol!

I have Photoshop CS2 vsn 9.0 with the Camera Raw 3.7 update and the Digital Negative Converter. I cannot open any RAW files. Does the fact that I've opened them in Lightroom 5.0 before make a difference?

When I try to open the RAW file (CR2) from the Photoshop application or from the Bridge (even while holding down the shift key) I get a message saying it's not the right kind of file. When I try to convert using the converter, it won't recognize the files.

Which operating system are you using?
Which camera are the camera raw files from?
Did you convert the files to dng using lightroom or the standalone dng converter?
If using the standalone dng converter, which version?
In the dng converter did you try setting the Compatibility for Camera Raw 2.4 and later
(Preferences>Compatibility)
You should also be able to send the files from lightroom to cs2 without converting to dng, either by using Photo>Edit In>Photoshop or setting cs2 as an external editor in the lightroom preferences

Firefox crashes when opened and the same in safe mode

We're Sorry
Firefox had a problem and crashed. We'll try to restore your tabs and windows when it restarts.
To help us diagnose and fix the problem, you can send us a crash report.

Your Ask Toolbar is at least part of your problem. Someone may come along with specific removal advice; otherwise try the "Search Firefox Help" box above or Google.

PCI 6602:How can I use the digital lines of the board and in the same time to generate pulse train using a counter?

Hello!
My problem appeared when I tried to update my code from Traditional NI-DAQ Legacy to DAQmx.
I am using 2 counters (counter 5 and counter 7) from PCI-6602, to generate pulse train, and also the Digital I/O lines of the port 0 (the lines form 0 to 7). What I do in my application is that I am starting to generate the pulse train on the output of the 2 counters, and after that I am playing with the state of the digital lines.
In traditional there was no problem using the counters and the digital lines in the same time, everything was going perfectly, but in DAQmx this is not possible.
What happens: I start to generate pulse train on the output of the counters, no errors encountered, but when I try to modify the state of one line of the digital port the generation of the pulse train is stopped. This is happening when I start the task associated to the digital port.
My question is: it is possible to create a channel on the digital lines without altered the channels created for the counters?
Another thing what I manage to see using the "Measurement & Automation Explorer" and Test panels for PCI-6602, basically is the same thing, I generate pulse train on the output of the counter 7 and try to start a task on the digital line, but I get one error :
"Error -200022 occurred at Test Panel
Possible Reason(s):
Measurements: Resource requested by this task has already been reserved by a different task.
Device: Dev4
Terminal: PFI8"
Instead if I use the counter 0 or counter 1 to generate pulse train I don't encounter the same problem.
Which resources are used by the counters 2 to 7 from the PCI-6602 board and the counters 0 and 1 do not use?
Thank in advance for any replies!
Ciprian
Solved!
Go to Solution.

Hello Jordan, thank you for your reply.
I am sorry but I can not see or run your example, I don't use LabView, I use Visual C++ for developing.
Here is the code for generating the pulse train:
GeneratePulseTrain(unsigned long ulCount1, unsigned long ulCount2)
    short nStatus = 0;
    nStatus = DAQmxCreateTask("",&m_taskHandle);
    nStatus = DAQmxCreateCOPulseChanTicks (m_taskHandle, "Dev4/count5", "", NULL, DAQmx_Val_Low, 0.0, ulCount1,ulCount2);
    if( bTriggerMode == true) // if hardware trigger is enabled
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_ArmStartTrig_Type, DAQmx_Val_DigEdge);
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_DigEdge_ArmStartTrig_Edge, DAQmx_Val_Rising);
       nStatus = DAQmxSetTrigAttribute (m_taskHandle, DAQmx_DigEdge_ArmStartTrig_Src,"Dev4/PFI17" );
   //set the internal timebase
   nStatus = DAQmxSetCOCtrTimebaseSrc(m_taskHandle,"Dev4/count5","20MHzTimeBase" );
   nStatus = DAQmxStartTask(m_taskHandle);
    return nStatus;
And the code where I try to set the digital line:
SetChannelState(short nState)
    short nStatus = 0;
    uInt8 wrtBuf0[1]={0};
    nStatus = DAQmxCreateTask("",&m_taskHandle);
    // Configure line as output
    nStatus = DAQmxCreateDOChan (m_taskHandle, "Dev4/port0/line0", "", DAQmx_Val_ChanPerLine);
nStatus = DAQmxStartTask(m_taskHandle);
    wrtBuf0[0] = nState;
    nStatus =DAQmxWriteDigitalLines (m_taskHandle, 1, 0, 0, DAQmx_Val_GroupByScanNumber , wrtBuf0, NULL, NULL);
    nStatus = DAQmxWaitUntilTaskDone(m_taskHandle,10);
    nStatus = DAQmxStopTask(m_taskHandle);
    nStatus = DAQmxClearTask(m_taskHandle);
    m_taskHandle = 0;
    return nStatus;

I changed my browser fill and the update does not show in the preview mode

I changed my browser fill and the update does not show in the preview mode. I saved and restarted muse but the problem is still there. Any thing else I can do? Could it be something that changed in the file?

Hello,
What did you put in the "browser fill" area, an image or a color? WIth gradient or with solid color? Also, does it show fine if you "Preview in Browser"?
Screenshots showing the Browser fill section (like this: http://screencast.com/t/RHqdVPP4) and the display in Preview mode would also be helpful.
Cheers
Parikshit

FlexiJack Digital I/O Mode L

I cannot get the FlexiJack to stick in the Digital I/O mode following computer re-boot. The Digital I/O still shows that it is selected but the only way to get it to work following computer re-boot is to unselect it and then re-enable it. Has anyone else experienced this problem and if so what is the solution?I have all of the latest updates installed.

http://forums.americas.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=47232
2'nd last post (from Cat @ Creative)
Edit: Appears the link in the referred to post isn't working, was yesterday.Message Edited by johnston2 on 0-20-2006 06:44 PM

How to keep the digital audio ouptut alive?

I'm connecting my MBP audio via the optical digital audio connection and the digital stream disconnects after a short time (30 seconds? I haven't timed it.) whenever there's no audio coming out of the MBP: the optical actually stops transmitting (the LED goes dead).
When it disconnects, my audio system tells me there's no signal and whenever an audio event occurs, it wakes up and inevitably the top of the audio signal is missing, as there's not enough time for the receiver to "wake up" before the audio event happens. I've actually tested this on two systems and it does the same thing.
So, is there any way to keep the digital output alive, even if silent? I'm running powered with settings on "Performance" so there's no power-related reason for the digital audio to turn off. I haven't been able to find any other system settings that could help. Thanks for any pointers.

Hello,
I out a page before the page which takes long to load with the following xhtml tag:
    <xhtmlb:protectDoubleSubmit active = "true"
                                timer = "2500"
                                text   = "<img src='/sap/public/bc/ur/Design2002/themes/sap_tradeshow/common/loading/loading_ani.gif'>"
                                title = "De werklijst wordt geladen..." />
But the page is not kept alive. What does the parameter timer? Must it be set to 0?
With regards,
Frank

UIView does not fill the screen in Landscapte mode

Hi,
I have a XIB and an associated UIViewController class, I set
- (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceO rientation {
return YES;
But I found if I open the view, then rotate the iphone to landscape oriention, the view got rotated too. But the view is not expend to fill the space in horizontal direction, the width of the view does not change. Why?
Thanks,
fm

aquador
What is the project preset that you have selected for your Premiere Elements 13 project?
If you do not know, please see readings for Edit Menu/Project Settings/General and the readings for Editing Mode,
Timebase, Frame Size, and Pixel Aspect Ration.
What are the properties of your source media? Does your import fill the Edit area screen when imported?
What file size do you want to import to, 1920 x 1080? If so, is that because your export is not filling your player screen?
If you want to set frame size higher than 1920 x 1080, please see Publish+Share/Computer/XAVC-S and the Advanced Button/Video
Tab for customizing the preset. But a lot of details before we get to that.
Including, what is your player and have you looked at the player settings?
ATR

Can't download the digital booklet of a purchased album.

Hello, guys. I purchased an album on a divice(my iPhone), but when I opened my computer, itunes didn't download the digital booklet automatically. And the digital booklet can't be downloaded at the 'purchased' option. I really need the digital booklet, what should i do? Thanks for your help.

I tried a few things. Not sure which one made it work. These are from an HP standpoint.
One attempt was going to the Edit toolbar/Preferences/Store button and click Always check for downloads and click the Books box.
The second was by going to View/Show Sidebar. Then under Store, doing a left click on the "Purchased" and select "Check for available downloads."
Hope that helps.

How do I keep the format in a fillable PDF, specifically the "$" symbol and the 2 decimal places?

I created a fillable form in Acrobat Pro and when we use it in Adobe Reader on the iPad, the preset format for money doesn't stay when the fields are populated, but if we email the filled form back to the iMac, the format is there and it's fine. Any suggestions? Do I need to do something with the original fillable form so that it carries over to the iPad?

I have been having a similar issue for a client's interactive PDF report that needed the "Show/Hide" feature in InDesign to reveal many acronyms' definitions in a "Pop-up" box when the acronyms were clicked on. Then the "Pop-up" boxes could be clicked on to close themselves using the same "Show/Hide" feature. While I have been going a little crazy the last FEW MONTHS scouring the forums and blogs (and just spent an hour and a half on the phone with Adobe's tech support staff that apparently only support desktops and laptops but have NO CLUE about the delivery of Adobe content via tablets and other mobile devices), I can say that a few things have been helpful - on the expert blogs (but sadly not in any of Adobe's support forums or call centers).
Buttons in interactive PDFs are NOT supported in iBooks or Acrobat Reader on the iPad.
Basic buttons, like navigational buttons (go to next or previous page) or submit, DO work in the "PDF Expert" app, which is $9.99 in the App Store.
So far, no matter which workaraound I have tried from the forums and blogs, the "Show/Hide" buttons still do NOT seem to work properly in even the "PDF Expert" app. (I see a highlight field where my buttons and pop-ups should be but no content in them - no text and no background - only a translucent highlight that shows that somewhere in there it's trying to work. The highlight fields even show and hide the way the buttons and pop-ups are supposed to, which is maddening!)
The only recommendation I could get from the Adobe tech support folks was to use InDesign and the Digital Publishing Suite (DPS) instead and publish an app through the iTunes Store.
Unfortunately that is NOT an option for me because my client's report is confidential and being sent to only a small group of less than 100 people.
I could bypass the iTunes Store and distribute the "Ad Hoc" method of attaching the .ipa file (the app file) to an email list of up to 100 people but my client would have to buy the DPS Enterprise Edition, which costs upwards of $20,000. (Yes, that's $20K in American dollars.)
There is NO option to distribute "Ad Hoc" with the Single Edition of DPS which comes with the Creative Cloud. I guess a lot of people ask that of the DPS forums and the experts give cranky repies that "No, it is just not possible with any DPS version less than the Enterprise Edition."
There is no middle ground on this yet but a lot of people seem to be asking for it. What's up with that, Adobe? No support for the small to mid-sized businesses for simple interactive brochures and reports that they don't want to release to the world, just to a select few?
The only solution I have found even slightly feasible is to create buttons that control "Multi-State Objects" (or MSOs) to behave similarly to the "Show/Hide" buttons and create a DPS .folio file from the InDesign doc.
I still can't recommend that my client pays $20,000 to be able to distribute his interactive quarterly report but I think I found a way around a small distribution.
You can share a .folio file with people through an email from the "Folio Builder" panel in InDesign. (See this help file: http://helpx.adobe.com/digital-publishing-suite/help/create-folios.html and scroll down to the "Share Folios" section.)
Apparently, this link is not permanent, but I haven't found an answer anywhere as to when it will time out. I'm thinking at least 3 months will be enough for my client for the time being until the next quarterly report comes out. Hopefully by then Adobe will have come up with a cost-effective solution for the small to medium-sized business that wants to publish interactive documents for the iPad or the PDF apps on the iPad will become mature enough to handle these slightly more robust interactive features.
I hope this was helpful to some of you trying to do something similar. If anyone has an elegant solution for the nearly-working interactive PDF on the iPad, please let me know. Thanks in advance!

SB0358 and the Digital I/O mod

Similar Messages

Maybe you are looking for