SBH-52 not powering on

I've been unable to power on my SBH-52 for the last week or so. It suddenly stopped working while using it one night I can't get the thing to power on no matter how long I hold the power button down. The screen shows the charge state if I plug it in. The system will go into the update mode when I hold Back while plugging a USB in and I was able to update it using the Software Updater It still won't power on. I'm not sure if the unit is borked or if it's just my power button. I've only had it for about a month.

Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
I'm sorry to hear. If you have tried with a software update/repair on your SBH52 via Update Service (http://www.sonymobile.com/global-en/tools/update-service/) and it still wont power on, I suggest that you contact your local support team to get information about how you should proceed in this case:
http://www.sonymobile.com/global-en/support/contact-us/contact-info/
 - Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Similar Messages

  • My iphone 5 is not powering the scree, when i connect the iphone to the power it only vibrates

    my iphone 5 is not powering the scree, when i connect the iphone to the power it only vibrates o make the connect sound (is like the sound when you connect the phone to power) and the screen remains black, itunes recognizes the iphone, but i cannot do a hard reset because the power button does not work, and have password in my phone so itunes wond restore it. i want to know if is a hardware problem like the mother board o something. help please

    If you have iOS 7 installed, you can try to restore it via the instructions given by lllaass in https://discussions.apple.com/thread/5634135
    As an alternative, you could take it to an Apple store genius bar and have the techs test it and see what is wrong beyond the failed power button.

  • Copying iMovie back to tape: "your firewire camera is not powered on"

    I'm trying to follow iMovie 6 instructions for copying a movie back to tape.
    I connected my camcorder to the computer with the firewire cable, and it shows up in the Share-->Video Camera menu as an attached device. (It's a Canon Elura 100, btw.)
    So all seems well until I start the procedure, and then I get a "Cannot Export to Camera" error message that says "your firewire camera is not powered on or is not available."
    My ever so slow brain thinks this might have something to do with the fact that I'm using the DV/firewire cable that I used to import the footage into my iMac, and maybe it only sends stuff OUT the firewire end, and won't send video the other way?
    Do I need a different kind of firewire cable?

    Thanks for your assistance!
    I bought this camcorder from Amazon.com (USA) and I have not daisy-chained it anywhere. I've only connected it to one device at a time. It is capable of receiving digital as well as analog video, and can convert analog to digital.
    For example, I used my stereo-video cable to transfer footage from an old VHS tape played by our VCR to my Canon Elura camcorder via the Canon's AV terminal.
    Once the tape was safely transferred into my Canon camcorder, I then plugged my DV/firewire cable into the Canon's DV terminal, and the firewire end of it into the iMac. iMovie saw the Canon camcorder and imported all the footage very nicely.
    Now I would like to transfer the edited footage from iMovie back to a mini DV tape, and my iMovie help file says I can do it, but it's a little sketchy on what cables I should be using.
    The firewire/DV cable I used to send the footage IN to iMovie isn't working to receive the edited footage OUT of iMovie. So maybe I need a different kind of firewire cable?
    Thanks for any help you can offer!

  • HT201401 4s with latest software update will not power off, text will only vibrate, iPod only works with earphones. When I sync it with iTunes it works until power save mode starts, then back to not powering down, making text sounds, or playing iPod out l

    4s with latest software update will not power off, text will only vibrate, iPod only works with earphones. When I sync it with iTunes it works until power save mode starts, then back to not powering down, making text sounds, or playing iPod out loud.

    The Basic Troubleshooting Steps are:
    Restart... Reset... Restore from Backup...  Restore as New...
    Restart / Reset
    http://support.apple.com/kb/ht1430
    Backing up, Updating and Restoring
    http://support.apple.com/kb/HT1414
    If you try all these steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • My apple tv3  is not powering on.  Connected with Computer, with micro USB cable with power on, it is not shown in Devices.  How to rectify

    My apple tv3, serial no. C07JWBZ9DRHN is not powering on.  Connected with Computer, with micro USB cable with power on, it is not shown in Devices.  How to rectify

    You have to remove all cables before connecting to your computer with micro usb. Power is only connected when using a 3rd gen device and done after the initial connection.
    http://support.apple.com/kb/HT4367?viewlocale=en_US&locale=en_US

  • How to print to my wireless all in one photosmart prem c410 when printer is not powered on?

    how to print to my wireless all in one  photosmart prem c410 when printer is not powered on?

    Hi,
    You cant print to a printer that you physicly turned off. Most network printer have a sleep mode, so leave it on and after a while it should go into a sleepmode. And should wake up when a printjob is being sent.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Although I work for HP my posts and replies are my own
    Please mark the post that solves your problem as "Accepted Solution"

  • 27" thunderbolt monitor is not powering back on with Laptop

    Since updating to the new version of Yosemite my 27" thunderbolt monitor is not powering back on when plugged into my laptop via the thunderbolt port. Suggestions on how to get it back up?

    Apple Support had me reset the SMC and after doing so my monitor came back up and functioned like it was supposed to.  Support said sometimes after updates we need to reset the SMC if changes aren’t cleared from the previous update resulting in behaviors like I was experiencing. Below are the steps i followed to reset the SMC.....
    1. Shut down the computer.

    2 Plug in the MagSafe or USB-C power adapter to a power source and to your computer.

    3 On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.

    4 Release all the keys and the power button at the same time.

    5 Press the power button to turn on the computer.

    On MagSafe power adapters, the LED might change states or temporarily turn off when you reset the SMC.

  • I bought download Adobe Premier elements last year. It is on my old computer which is not powerful enough.  I have a new computer that is, I bought and upgrade for $69 but have got no where after several hours.  what do I do

    I bought download Adobe Premier elements last year. It is on my old computer which is not powerful enough.  I have a new computer that is, I bought and upgrade for $69 but have got no where after several hours.  what do I do?

    What are you trying to do?  What actions are you taking?  What happens when you try?

  • Macbook Pro late 2011 not powering on. The charger shows a blinking dim orange/green light.

    Macbook Pro late 2011 not powering on. The charger shows a blinking dim orange/green light. I have tried pressing the small button on the side of the macbook pro to check the battery, but no lights show up.

    Hey Angelo_here,
    I'd run through these steps:
    If your computer won't turn on, try each of these steps:
    Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
    If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
    Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
    Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
    If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
    MacBook Pro: How to remove or install memory
    MacBook: How to remove or install memory
    Mac Pro: How to remove or install memory
    Mac mini: How to remove or install memory
    iMac (27-inch, Late 2012): Installing or replacing memory
    iMac: How to remove or install memory
    Reset the SMC.
    If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
    via: Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/TS1367
    Welcome to Apple Support Communities!
    Regards,
    Delgadoh

  • USB not powering external drive on new macbook pro

    My new macbook pro retina display is not powering an external 750GB GDrive moblie. Is anyone having this problem?

    It seems as if a number of people are having problems with the USB 3.0 ports on the 2012 MBP's - particularly when it comes to external storage devices.
    As you  don't have a FW800 port (or, yet, an adapter) the best thing you can do is either return it to your local Apple Store and see if they know of a 'fix' (which I doubt - someone would have posted that by now), whether it's only occurring with some MBP models, and you can always file a bug report with Apple: https://bugreport.apple.com/cgi-bin/WebObjects/RadarWeb.woa/wa/signIn - you must sign in with your Apple ID.
    Hate to be the bearer of bad news, but there have been quite a few people posting here with the same problem.
    Good luck,
    Clinton

  • MacBook was restarting on its own and now is not powering up. What could cause this and how to troubleshoot?

    MacBook was restarting on its own and now is not powering up. What could cause this and how to troubleshoot?

    When did it happen? After updating/upgrading? or just randomly?
    You can try to perform a SMC reset and resetting the PRAM:
    SMC Reset -> http://support.apple.com/kb/HT3964
    PRAM/NVRAM -> http://support.apple.com/kb/ht1379

  • Iphone suddenly gone blank. Not powering on

    iphone suddenly gone blank. Not powering on. Any suggestions?

    Hello Navalagarwal,
    The following article contains a few steps that may help get your iPhone powered back on.
    iPhone, iPad or iPod touch: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Best regards,
    Allen

  • E540: Not powering up

    Few months old E540 is not powering up. When I press the power button, the led is lit and the fan turned on but nothing else happens. Nothing on screen and can't even open the DVD tray. Have tried fn+F8, removing battery without luck. Haven't done anything special recently or installed any new software. What next ? Any help is greatly appreciated.  

    Good day and welcome to the community.
    Please have a look at this Knowledgebase article:
    https://forums.lenovo.com/t5/11e-Windows-E-and-Edge-series/E540-Cannot-power-up-the-system/ta-p/1497840
    Does this seem aplicable to your situation?
    Regards.

  • Playbook not powering up, not charging, nothing

    My BB playbook is not powering up when placed in the charging cradle or when plugged into a computer.  I have tried hard restart and all kinds of  things - I am not even getting a red light.
    is there any way I can get it restarted, rebooted, or something so that it can take a charge.  I know it has to be powered up to charge - but right now nothing is working.  Please help!

    paulmitt wrote:
     but is there a chance that my playbook is just finished ....:
    Nope! It's just deeply and severely drained, and you'll notice references to that in the KB articles I linked for you.
    This happened on one of my PlayBooks recently, and it too some patience and work...if it's not TOO deeply drained, you will begin to see some life eventually via the no battery icon, or a low orange glowing pulsating LED at the top of the device.
    If it is VERY deeply drained, you will need to eventually use the PlayBook debricking method to bring it back to life. You will lose all media, pictures, etc., on the device however, if you have not made a previous backup.
    Try this, while connected to your charger. Press and hold the Power key, up and down volume (-/+) all three buttons simultaneously, for about 10-12 seconds. You should the red LED blink and that should allow a reset of the PlayBook and to power up.
    After charging 24+ hours:
    1- Press the powerbutton for about 20 seconds
    2- Charge PB for 2 minutes (use stopwatch)
    3- Disconnect powercable for 8 seconds
    You have to repeat step 2 and 3 total of 10 times. Then reboot by pressing power and + key for 22 seconds.
    Other users have reported this reset their device and got it working.
    You need to follow these instructions to "debrick" your PlayBook:
    1. (skip this if the devce is dead due to no battery charge) Do a backup of your PlayBook using your computer and BlackBerry Desktop Software version 7 installed. It can be downloaded from http://us.blackberry.com/apps-software/desktop/
    2. (skip this if the devce is dead due to no battery charge) Unplug the PlayBook and on the PlayBook press and hold down the power button until the unit forces the device off.
    3. With the Desktop Software still open on your computer and the PlayBook powered off, connect the PlayBook to your computer once again.
    4. You should see an error screen from Desktop Software popup with the options to Retry, Update, or Cancel.
    Very quickly choose the Update option.
    5. All information will on your PlayBook will be erased and a reload of the Software will commence to install on the PlayBook.
    6. Once this is complete your PlayBook will go back through the initial (as if new) setup wizard (entering the BlackBerryID, etc., and then you can perform a restore using Desktop Software to return your personal data from the backup. Applications which you downloaded from AppWorld won't restore, but they can be easily reinstalled using AppWorld > MyWorld section of AppWorld.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • X220i not powering up

    Hi all, I have a Thinkpad x220i that is not powering up.  The user was claiming poor battery life and not charging prior to this happening.  I had taken a look at it and it was charging up fine.  A couple of weeks later it will not turn on.  
    Only thing happening now is the battery light blinks green 5 times with the 4th blink lasting longer than the other then it goes dead.  Not powering up, no fans starting, no hard drive spin.  Nothing.
    Any help would be greately appreciated.  
    thanks! 

    It was new.  I removed the hard drive to retrieve the users data and when I plugged it back in the laptop was able to reboot.  I had tried the removal of memory and drive then reboot and it had not worked.  Not sure why it worked the second time after access the hard drive.  
    Upon reboot it did say that Windows was not properly shut down.  

Maybe you are looking for