SBlive Value and 2 audio out settin

Hi, Just a quick question. I want to be able to hook up 2. speakers to the front speaker out, and have the identical sound come out of the headphones I have hooked up to the rear speaker out. I had an old version of AudioHQ that allowed some option (Ibelieve it was 2 speaker legacy audio out or something like that) which allowed both the front speaker out and rear speaker out on my SBli've value card to have the same output sound. I just recently formatted and installed the new control panel, and I can't for the life of me find that option under the new version of audioHQ (.0) using windowsXP pro SP2.
All I want is a setup where I can listen to mp3s from anywhere in the house but then just turn the volume down on the speakers and play an online game through the headphones without climbing behind my computer to switch wires and without disturbing the wife. Any help would be much appreciated, or if someone has a better suggestion to my problem it would also help.

Wheresjj
Did this soundcard come preinstalled in your Gateway computer? If so you will need to contact your computer manufacturer for support as the card may be OEM. OEM components are often modified from their retail standards and require special drivers that only the Vendor will have access to.
Jason

Similar Messages

Trouble running DVI video and HDMI audio out of 6950

Twin frozr iii 6950 2gb (X2 crossfire)
Asus VG236 Monitor
Windows 7
MSI P67A-G43 Motherboard
Yamaha RX-V371 Receiver
I have two Twin Frozr iii 2gb 6950 cards and am attempting to use the HDMI on the video card solely for 5.1 audio out to my receiver while using video through the DVI jack of the same card directly to my monitor without success.
-Audio functions if I run the HDMI from the card into my receiver, then out to my Asus VG236 monitor.
-Audio functions when I run from the card to my receiver then out to my plasma tv.
-Audio functions if I have the DVI run directly to the Asus VG236 monitor and HDMI to the receiver then plasma tv (only in dual display and the tv must be on for audio to function this way. If I turn the tv off even though the receiver is still on the audio stops working and windows sound lists the 'AMD HDMI Output' as not plugged in).
-Audio even fuctions when I run DVI to the monitor and HDMI to the receiver, then out to the HDMI port on the same monitor but the monitor will only run at 60hz this way even when DVI is selected on the monitor, as though it defaults to the HDMI when dvi and hdmi are both plugged into the monitor.
And if i run the hdmi to the receiver "HDMI IN" port without using the "HDMI OUT" port from the receiver to anything, like my tv or monitor, the sound doesn't work and in windows sound the "AMD HDMI Output" is listed as "not plugged in" .
I purchased this monitor for the true 120hz capabilities, the HDMI on this monitor doesn't support 120hz, the maximum is 60hz. DVI is required to run at 120hz. I don't see any option in windows sound settings or CCC to resolve this.
I have also tried disabling onboard audio in BIOS with no effect.
For now i'm running the audio out my MOBO jack through an optical cable to the receiver but optical only supports 2.1 sound.
Any suggestions you can offer would be appreciated, thank you

bump,
Anybody?

Optical digital and analog audio out

I just purchased a Pavilion 500-214 with IDT High Def Audio CODEC / DTS Sound+
Is it possible to get both opitcal digital audio out and analog (speakers/headphones) out at same time? Stereo amp needs access to both for multizone/source function. I can manually pick one or the other before playback - it is clunky in that when switching audio out devices the active will turn off but one switching to does not always turn on. But i really need both simultaneously active for amp to work properly. I have also found rear speaker jack to be more stubborn during switching than front headphone jack.
This question was solved.
View Solution.

Hi zombi1,
Welcome to the HP Forums!
I have done some research on whether or not one can utilize both digital or analogue audio out at the same time, and unfortunately this is not possible.
Thank you for posting, and Happy Earth Day!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Bluetooth Headset and Headphone audio out at same time?

My GF and I were on our way to NYC on Acela and decided to watch a movie to kill time. I inadvertenly forgot to bring my headphone splitter, so I figured I could plug in one set of earphones into the headphone jack and use my bluetooth wirelessely. Upon doing so, the Mac Pro brand new, would only let me select one output via sound preferences. Any ideas or works arounds to allow audio out to both headphone jack and wireless? Is it possible to attach 2 bluetooth sets for wireless capabilities to watch movies?
Message was edited by: Special Educator

Yeah I do it. I use a Jabra bluetooth adaptor that uses the headphone port. Then I tuck the luetooth unit under my Marware Relay wristband.
Motorola S9
Jabra A120s
Marware Sportsuit Relay
Nike + Ipod Sport kit

65x900b - two questions - amazon in dolby 5.1 and using audio out with subwoofer

Does the amazon app output 5.1 like netflix? I can't seem to find any way to set the amazon audio.Also I have used a 1/8 y adapter and plugged it into the audio out on the TV. One end of the Y goes to my A/V receiver and the other to the wireless transceiver for the subwoofer. The cable from the wireless transceiver to the tv is a mono cable so if i have them both plugged into the Y one of the channels cannot be heard. The subwoofer works fine. But when I change to audio out like I said I loose one channel. When I unplug the mini cable from the Y adapter however I get full stereo sound outputting. Is there anything I can do to resolve this conflict. Can I use a stereo mini cable for the wireless transceiver for the subwoofer.ThanksLloyd

Hi lgroveman,
Welcome to the Sony Community!
Amazon with Digital Dobly 5.1 is already supported. Please make sure to update your TV to the latest software, kindly check this link for further details and steps by steps procedures. In addition, please make sure to perform the steps below to Refresh the internet content of the TV once the installation is complete.
Press the HOME button, then select [Settings]
[Network] → [Refresh Internet Content].
The Analog Audio Out cannot drive both a stereo system and a Subwoofer. If you connect a Subwoofer to the TV SWF-BR100 the frequency response of the audio output is limited to the subwoofer frequencies.
To output 5.1 surround sound from your TV an ARC (HDMI ) or the Optical Out connection is needed because analog audio out support stereo sound.
If my post answers your question, please click the button below "Accept as Solution"

Logic 8 and mbox audio out problem

Hi
I have a problem when using my digidesign mbox with logic 8. When I set the core audio to Device: Digidesign HW (Mbox) in prefs in logic I can record with my mic (i see that the audio is going in) but I do not get any sound out, not from the tracks I have reWired from reason, or the mic. Its like the audio out is disabled when I choose the Mbox device. If I choose to use built in microphone or built in line in i can both hear the reWired sound and the internal mic in my imac, but then the external mic using the mbox does not work...
So basically I can record sound with the external mic, but then I dont here anything (not the audio in logic or the mic) or I can record with the internal mic and also here the other sounds (rewired or other tracks in logic).
This is really annoying, since I just want to be able to use my good external mic or guitar through my mbox and I cant...
btw, when using garageband it works wothout any problem to use the mbox, so its not a problem with the drivers or so...
Anyone have had similar problems, or maby someone has a solution. I would be really greatful.
Thanks
Mr Sinclair

Oh
and another thing... It also works in Sountrack pro as well as in garageband... It is only in Logic 8 I can not hear the sound I am playing once I have chosen the Digidesign device for input. It is almost as it automatically choses the digidesign device for output as well, and not the speakers on my computer... (in soundtrack pro there is a choice to chose input and output device, in logic only the input device... could this be the problem?) I could use soundtrack pro, but it does not have the ReWire function I need... and also I like logic better.
Any suggestions?

Is there any way to use bluetooth and force audio out at the same time?

I have an older treadmill that uses IFit which means a program on my phone controls my treadmill via an aux audio cable. I like using BT headphones so I don't have cords hanging. So...I'm trying to figure some way to either a) have iphone connected physically to treadmill but bt'ing music to my headphones at the same time or b) get iphone to communicate with two different bt devices simultaneously. (Treadmill can also be controlled via BT, but I still need the BT for headphones)
Any ideas would be great. I currently have cable running from treadmill to iphone and headphones via a splitter but it's a LOT of cord hanging which makes things difficult.

No. FaceTime is one on one only.

Optical out and RCA audio out -- do they both work simultaneously?

On teh Apple TV, does audio get output over the digital optical output and the RCA audio jacks simulatenously?

Optical and HDMI sound works simultaneously as well. You can use an optical to SPDIF converter to convert it to coax, then send across the house via cheap RG6 satellite cable and convert it back if necessary to optical if you want your surround amplifier in an equipment closet somewhere or away from your wall mounted TV.
When you don't want surround sound, you can simply turn the TV speaker volume back up. I haven't tried the RCA jacks, but it appears that all audio outputs are active simultaneously.
When you activate volume control, the apple remote will modify the volume level of the optical output as well.

Why doesn't time capsule come with AirPlay and an audio out plug? I have to buy an Airport Express station and put it right on top of my time capsule to wire it to my stereo. Doesn't make sense...

My Time Capsule is right by my stereo and would like to stream my itunes there. But it looks like I would have to add an Airport express station right on top of my time capsule to do this. Which doesn't make sense to have 2 wireless routers on top of each other. Is that the only way?

Well you can't do it with a Time Capsule.
You could get an Apple TV instead of an Air Port Express and then you can get video as well..

Multiple Audio out: usb dac audio out and hdmi out

Good afternoon everyone, I have a 2010 mac mini with the following audio set up.
- A usb dac (xtreamer) connected to my stereo amplifier
- an Hdmi cable to the tv to get video and audio diretcly to the tv
Is it possibile by any chance to get simoultanesly audio output both from usb audio out and hdmi audio out???
In "midi preference panel" I tried to create a "virtual" sound card but i am not able to get sound simoultanesly. or via hdmi, or via usb.
this is quite disappointing because if I want to listen to music with the amplifier and then watching a simple video with mac mini and tv only I need to go back to the audio preferences and set up manually each time.
Is it possible to solve this issue???
Thanks a lot and gretings from Italy

I can select ATV audio out (Airplay setting) to either my Airport Express or my computer so it must be transmitting via airplay. Using a combination of Airserver, Airfoil and Airfoil Speakers I managed to get the ATV audio content on both my PC and my Airport Express at the same time but it cuts out the ATV audio.
My aim is to have a movie on ATV transmitting the Audio to ATV AND my stereo (which is hooked up to the Airport Express).
Cheers

Audio out of sync with elemental plugin, and slower than my i7!!!

Maaannn!!
I just got a PNY nvidia quadro 1800 with elemental accellerator plugin. I just transcoded 2 hours of HDV straight from premiere 4 with Adobe Media Encoder using the Elemental codec and the audio is out of sync. It plays out of sync on the Blu Ray disk, and in Encore4. The audio is perfectly synced in Premiere. I just did another project a week ago without the Elemental, using the default Main Concept encoder and the audio is perfect. I am pretty sure I have the latest version of the Elemental Accellerator because there is a button to check for updates and it says there are no updates available. Does anybody know what is wrong here?.
The transitions are getting messed up. I can see a small section with the audio synced, then the video repeats after a second throwing them out of sync. I also suspect that the Elemental accelerator does not process any faster than the default h.264 for Blu Ray encoder. I hope I did not waste my money on this nvidia quadro 1800..
Whoooaa! I just woke up and checked the transcoding time.. To transcode approximately 2 hours of HDV it took 6:35 (hr:mm) with the elemental accellerator and it took 5:09 with my i7 920 chip!! Was that nvidia card a waste of money, or what?!!! Between the slower speed and the audio out of sync, I'd say I made a BIG misteak.. Does anybody want to buy a PNY nvidia quadro 1800? it'll be on ebay very soon..
Win7 64bit, Master Collection 4, i7 2.66 Ghz, Kingston Triple Channel DDR3 1600Mhz 6Gb, ASUS P6T, PNY nvidia quadro 1800.....

Thanks Neil,
I don't think my audio interface has anything to do with it.. I am using Adobe Media Encoder for the export and the Audio interface's latency has nothing to do with it.. I see the source of the problem but not the solution.. The Elemental plugin is not working properly with the transitions in Premiere. The transitions are visibly botched and the sound is in sync for a partial second of each clip, then the video skips backward as the sound keeps playing. This happens on every clip after the transition.
Whatever you were talking about might have to do with some kind of real time export, but to where? I think Premiere might have some auto plugin delay compensation for audio tracks.. I dont think you even read my post.. My MOTU 896 Mk3 audio interface has a 128 sample buffer leaving a few milliseconds of latency, and I can set it as low as 64.. This still has nothing to do with my problem.. Thanks for your input..
I am curious to know what you thought I was capturing elemental streams and audio from my interface in real time to.. I was unaware of anything that works like that in this type of editing..
The bottom line is that my i7 chip gets the job done much faster than the quadro 1800, and that's a shame that I spent the money on the 1800.. On top of that it doesn't even work properly!!

Audio out options question - HDMI + component?

I have looked thru the manual and forums, but have not seen the answer to my question.
If I hook an ATV to my TV with HDMI, and also use the Right and Left (red and white component) audio out cables to my stereo (which does not have TOS link digital audio capability), will I get sound delivered to BOTH units at the same time? Basically, I'd like sound to go to my TV and my stereo.
I see in the ATV manual that it is possible to use HDMI and digital audio out. DVI video and component audio out, but I need HDMI video/audio AND component audio out.

The easiest way to accomplish this is to use the HDMI cable from the ATV to the TV and then export the sound from the TV with with either RCA, toslink, or digital audio out cables to your stereo. That is what I do at home. I have a DVR cable box, DVD player, and PS3 Blue Ray player and a HD video camera all hooked up via HDMI to a HDMI hub to the TV and then I can switch the stereo from either the TV audio out (all of the above) or the airport express where I stream music to the Stereo. There is no doubt that the sound quality from the BR HDMI cable of the PS3 has a superior sound.
A tech at curcuit city told me there is a difference in sound between, a expensive Monster HDMI cable and the less expensive cables now available on line, but I have not tried a A/B comparison yet, but am planing to do so. $50-60$ vrs. a few dollars on line aftermarket.
Hope this helps.

Longer cable (6') connecting female RCA L R Audio Out to Headphones In 3.5 on Vizio 32"?

What I want to do, since although the Vizio manual and the Best Buy sales rep, looking at the Vizio E320i-AO thought it came with a heandphone jack, it DOES NOT. It does have, where the manual thought the headphone jack was, L and R Audio Out ports. My question concerns if anyone can suggest a 6' or so cable that would allow me, then, to connect Volume Out on my TV to Volume In to my headphones. Thank you.

OK. Apologies. I ordered the wrong cable, based on a sales rep's suggestion and my not paying attention: more my fault than his. Anyway, got the order cancelled. The suggestion given to me is to get a 3" two RCA males to 1 3.5mm female. And then find a cable with a female and a male 3.5 ends. If anyone has been reading any of my posts, I offer my apologies. I am back to square one.

Preventing Digital Audio Out from "Sleeping"?

I'm using the mid 2010 Mac Mini and digital audio out.
My receiver is showing the loss of digital audio signal when the mini hasn't played a sound for awhile and then comes back when audio is played.
I loose about 1 second of audio though when this happens which is bad for quick sounds. Subsequent sounds play fine until it "sleeps" again.
In Windows it keeps the digital signal live at all times which is what I want in Snow.
Is this possible?

You should only experience a delay when you switch to a new source of sound. Such as first starting playback in itunes, or first start Pandora, or just starting to watch a video clip.
This is because OSX typically only outputs a digital bitstream when there is an actual audio bitstream source currently "playing."
I regularly see my Denon receiver indicate a loss of the audio bitstream and then indicate when it starts up again. I have not experienced a problem because of this.
I suspect your particular receiver is slow to respond to new bitstreams. I have two suggestions to help mitigate this:
First, it might help to lock your receiver to the optical audio input (for that particular source selection). Since the receiver is likely simultaneously monitoring the HDMI, coaxial and optical inputs for a new bitstream, this could cause a delay in its reaction to a new audio stream.
Also check the receiver's manual and see if there are adjustments for its digital audio behavior. Disable any buffers or processing effects or "enhancements."

Samsung HLN4365WX Audio out

I would like to hook up external speakers/soundbar to subj TV, the instruction manual is very vague, rear jack Vidio/Audio Monitor Output says "Sends a vidio signal from the TV to an external source, such as a VCR" , RCA jacks 1. vidio out 2. Right out, 3 Left out.
Now my question, can receiver to speakers or soundbar be hooked to thr Right and Left Audio out RCA jacks?
Thank's for you advice/help.

hallybee wrote:
I have firmware 2.2.1, so that's not it.....I know there's a sticker that says it will be fully functional after the release of Android 2.2. But the phone came to me with 2.2.1 installed, and I did check for an update just to be sure, and was told there wasn't one.
I have a vehicle dock, model ECS-M985BE. I'm trying to use the audio out port with a wired headset. I get no sound thru the headset at all, though the headset works fine when the phone is not hooked up to the dock. I've tried multiple headsets/earphones, and I also had Verizon send me a new dock in case there was something wrong with my first one. Nothing's solved it. I called Samsung directly, but after they wanted to transfer me for the fifth time, and I'd been on the phone a total of a half hour, I couldn't handle it anymore.
I've tried using it in "car mode" and out of "car mode." When in "car mode," if I pick the phone icon, it tells me to "connect the external speaker to the accessory." But it doesn't recognize the headset when I plug it in. If I have the headset plugged in and then pick the phone icon, it still gives me the message to connect the external speaker.
In all of these instances, I can hear the call through the phone earpiece, and can turn on the speaker and hear it there as well - as if there is no earpiece connected at all. But I get no beeps or any other indication a device has been plugged in.....but, I don't get that when the phone is off the dock and I plug in the headset, either, so.....
Anyone have any ideas or input? The only thing I've tried was suggested by the first person I talked to at Samsung: download any free car dock app. That didn't help either.
I would also check with your local law enforcement, as I know wearing a headset during driving is illegal in some states. It prevents the driver from hearing emergency sirens, etc.

SBlive Value and 2 audio out settin

Similar Messages

Maybe you are looking for