Scan doesn't work after downloading Windows 10

After downloading Windows 10, scanning will not work on my HP Officejet Pro 8620 all in one printer. I used HP Print and Scan Doctor program and it stated that it fixed my scanning problem. However, when I attempt to scan I get a message that says it cannot find the application to support the selection. BTW...I have also unistalled and reinstalled the driver for this printer thinking it might been to "reconnect" in some way with Windows 10. On another note, by DVD drive now doesn't work either after downloading Windows 10. HELP !!

Hey there,
Try the following step's, i believe it will help you overcome the issue.
1.Start by dissconnecting the USB cable.
2.Remove the Printer Driver from the "Devices and printer's" which can be found in the control panel.
3.Download this file (http://ftp.hp.com/pub/softlib/software12/COL48430/al-117537-4/DJ1510_188.exe) which is the full solution for the HP Dj 1510 series.
4.Extract the contents from within the file.
5.Open up the "Utils" Folder and within choose the "x64" folder, Inside you should be able to spot a File called "RemovePreInstalledDrivers" >> After you will open that file a Black screen will open, Wait for it to close then move to the next step.
6. Go back to main folder where you have already extracted the software and Right click on the x64.msi file (Name will most likely consist your printer model) and choose the "Repair" Option. >>Afterwards you will be prompted to preformed a restart. (Incase you will get a Messege saying "This action is only valid for products that are currently installed" Just double click the file instead)
7.After the restart, Head into Local Disk C/ProgramFiles/HP/PrinterModelFolder/bin/USBSetupLuncher and double click it.
8.Follow the steps shown to you and connect the USB cable when you are asked to.
That should add the scanner to Your imaging devices.
Best Of luck~

Similar Messages

My sound is not working after downloading windows 10

My sound is not working after downloading windows 10 please can you help me?

right click start then select device manager see if there are any yellow ! in triagle symbols next to any device if there is you may need to reinstall the audio driver

Flasplayer doesn't work after download in MAC

I've downloaded the new version but, after the installation procedure it doesn't work.
I've modified the preferences in safari but still not working.
I've norton antivirus in MAC but it doesn't work as firewall.
I know the last updates in MAC OS have changed security protocols but I'm not able to see any video where flashplayer is needed.
Thanks,
D

First off... GET RID of that garbage from Norton!!!
1. You DON'T need anti-virus for Mac because (and I want to be absolutely clear about this) THERE IS NO SUCH THING AS A VIRUS FOR OS X. (See: https://discussions.apple.com/message/23885605#23885605)
2. Of all the so-called anti-virus products for Mac, Norton has got to be the worst, without a doubt.
3. Even if you run Windows in BootCamp or as a Virtual Machine... You ONLY need anti-virus on the Windows partition or in the VM. ANYTHING that can infect a BootCamp partition or VM CANNOT affect your Mac OS X partition... at all.
4. Anti-virus products for Mac CAUSE more problems than they could ever possibly resolve. OS X is more than capable of protecting itself from "malware".
Stepping off my soap box, Try a "clean install": How to perform a "clean install" of Flash Player in Mac OS X
99.9% of the time, that will resolve your Flash Player issues.

HP photosmart C6280 scan doesn't work after once working

I can't understand it - six weeks ago I came on this forum with this problem and it was solved. I used Preview and' import from scanner' which worked fine. I tried it yesterday and it doesn't work again! I've downloaded new drivers from a site suggested to someone else on the forum with the same problem, but it still doesn't work. All I get when I go into System Preferences - printers & fax - is 'No scanner selected' its driving me mad! I had to go and do scanning from my old PC! Heresy! Someone please help!

I seem to have resolved this problem now. I uninstalled ALL stuff I had downloaded including drivers etc., and just went to the page suggested on this forum and put on the new stuff from HP I can now scan properly from my computer without using Preview.

Little house (Home button) doesn't work after reinstall Windows :/

Which driver is for the home button on an HP Touchsmart 600-1050? I reinstalled Windows 64-bit and now the little house does nothing. I don't want to install all the driver because I know how HP is with bloating our computers with spam.
http://neworleanscomputerrepair.com

Hello Pawn3d:
Love your comment but for real HP does not spam your computer. You said you reinstalled windows. How did you go about it did you use your recovery disc or Windows 7 disc? Can you please give us more details? Did you down load the fattial Hp Support Assitant? Pior to this restore? The latest update version will distroy your computers system operating sytem. My Touchsmart 600-1050 is on its way back from HP repair center making that huge mistake of running HP Support Assisant up date. End result HP replaced two hard drives and mother board. Its not a driver its the HP Touchsmart ( Desktop ) software that is corrupted on your computer. Yes it may open up and respond to icons but doesn't mean it opens up by extrenal buttons. My computer should be ariving back with in next two days. I will open it up and check the drivers and serivices list and post them here for you. If my I had my computer I would post it now but its on fedex truck in route.frrw I will be back as soon as it arives and give you the required information. Hopefully HP fixed it right this time.

Gamepad doesn't work after upgrading windows 8.1

Hi, i've recently upgraded my asus F550C to windows 8.1 .
Everything seems to work fine, except my gamepad that worked perfectly before the upgrade. Should I unistall the old drivers, and reinstall the new ones? If so, how?

Hi
your gamepad separated from your laptop right?
search the model at manufactured site and find the driver which compatible with Windows 8.1, I suggest to reinstall the driver and also find the update

Fit the window with mouse doesn't work after new update 10.9.2

Hi, I could fit a windows using my mouse wheel or two finger(on trackpad), doesn't work after I set up new Mavericks update(10.9.2) I'm using Haswell rMBP. Can anyone help me please? Thanks a lot. (Also, minimize with mouse wheel doesn't work too.)

Doesn't anyone having this issue?

HT4623 Landscape feature on iphone doesn't work after OS 7 download. HELP.

The landscape feature on iphone doesn't work after OS 7 download. How do i fix it?!

Swipe up from the bottom. Control center should cover about 2/3 of the screen. At the top right of control center is a circle with a lock in it. If that lock is closed, tap to open it.

Downloading new photos - iPhoto doesn't work after upgrading to Yosemite

Hello,
Since I upgraded to Yosemite, iPhoto has stooped working after downloading photos from my Sd card.
Some picutres downloaded are black while some others are ok, but in any case I have to restart my iMac because every apps running can't be used anymore.
That happens only with iPhoto, after downloading, instead normally it works.
Now I use Aperture and everything is fine but I'd like to figure out why iPhoto acts like that.
Do I have to trash it?
Thank you.
Fabrizio

There have been a number of reports on here from folks with Raw issues after updating.
This thread:
RAW files suddenly show up as "not supported" (Aperture 3.5.1, OS X 10.10)
explains how to delete and reinstall Raw support. It has worked for others.

[Solved] Network doesn't work after hibernate?

Hello! This is my first legit Linux install so excuse me if I'm a bit slow. I installed Arch last night and everything went smoothly. However, after I tested out hibernate on my machine, the network doesn't seem to work. Just prior to the hibernate, I installed Pidgin and Skype but they worked alright, so I think that the hibernate caused a problem on eth0.
I have an Asus P8Z68-V Pro motherboard with an Intel 82579V Gigabit Ethernet Controller that's using the e1000e driver. Running "dmesg | grep e1000e" says that it is up.
I'm not entirely clear here, but from reading, I think that I have several ways of connecting to the network, including network, dhcpcd, networkmanager, and wicd. I am using wicd so I did the following (or at least I think I am only using wicd):
#rc.d stop network
#rc.d stop dhcpcd
#rc.d stop networkmanager
Similarly, I put a ! in front of network in rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
# startup and during the boot process. If set to 'no', the C locale is used.
# HARDWARECLOCK: set to "", "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# Note: Using "localtime" is discouraged, using "" makes hwclock fall back
# to the value in /var/lib/hwclock/adjfile
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# Note: if unset, the value in /etc/localtime is used unchanged
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.UTF-8"
DAEMON_LOCALE="no"
HARDWARECLOCK="UTC"
TIMEZONE="America/New_York"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
# Replace every !module by an entry as on the following line in a file in
# /etc/modprobe.d:
# blacklist module
# See "man modprobe.conf" for details.
MODULES=()
# Udev settle timeout (default to 30)
UDEV_TIMEOUT=30
# Scan for FakeRAID (dmraid) Volumes at startup
USEDMRAID="no"
# Scan for BTRFS volumes at startup
USEBTRFS="no"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="Vicious"
# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
# Wired network setup
# - interface: name of device (required)
# - address: IP address (leave blank for DHCP)
# - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
# - broadcast: broadcast address (ignored for DHCP) (optional)
# - gateway: default route (ignored for DHCP)
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# broadcast=192.168.0.255
# gateway=192.168.0.1
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=
interface=eth0
address=
netmask=
broadcast=
gateway=
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
DAEMONS=(hwclock syslog-ng dbus !network netfs crond wicd)
Restarting eth0 through wicd-cli still did not work. I also tried resuscitating the network via instructions on the configure network page before trying to focus solely on wicd.
I found a few similar problems on the forums by searching "wicd hibernate" and tried several solutions but they did not work. Several problems seem to be that the network doesn't work after a suspend because I guess the stuff in RAM did not get saved? But people were able to restart the network by running "/usr/lib/wicd/autoconnect.py" and I wasn't able to get this to work. As a final effort, I added "resume" into mkinitcpio.conf and placed the machine into sleep again to see if it may magically reset something but of course this did not happen .
mkinitcpio.conf:
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run first, so it may be used to
# override the actual binaries used in a given hook.
# (Existing files are NOT overwritten if already added)
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options
# like so:
# FILES="/etc/modprobe.d/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
## This is identical to the above, except the old ide subsystem is
## used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev pata mdadm encrypt filesystems"
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect pata scsi sata resume filesystems usbinput"
# COMPRESSION
# Use this to compress the initramfs image. With kernels earlier than
# 2.6.30, only gzip is supported, which is also the default. Newer kernels
# support gzip, bzip2 and lzma. Kernels 2.6.38 and later support xz
# compression.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""
Not sure if my fstab.conf is useful but if this has something to do with settings getting "lost" in swap, here it is. Linux is on an SSD and HDD (sda and sdc) and Windows 7 is on a HDD (sdb).
fstab.conf:
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
none /tmp tmpfs nodev,nosuid,noatime,size=2000M,mode=1777 0 0
/dev/sda1 / ext4 defaults,noatime,discard 0 1
/dev/sda2 /home ext4 defaults,noatime,discard 0 2
/dev/sdc1 /boot ext4 defaults 0 1
/dev/sdc2 /var ext4 defaults 0 0
/dev/sdc3 swap swap defaults 0 0
/dev/sdc4 /media/data ext4 defaults 0 0
shm /dev/shm tmpfs nodev,nosuid,size=10G 0 0
Is wicd causing these problems or did I configure something else improperly? Would appreciate any help to get eth0 up again!
Last edited by TheBigCow7 (2011-09-13 17:57:20)

Ok, I think I've made some progress! Hibernate definitely affects my network connection. Could this be a kernel 3.0 problem?
I noticed that ifconfig showed eth0 without an inet addr, just an inet6 addr for the longest time. e1000e seemed to be loading up ok. I'm not certain here, but I think that meant the dhcp settings didn't stick, or something along those lines.
Trying to use dhcpcd like the instructions here did not work. By some chance, one attempt did work and while it did, I downloaded and installed dhclient. After that one successful attempt, renewing the DHCP lease via dhcpcd did not work again.
Luckily though, I found that running "dhclient eth0" worked. My DHCP settings seemed to have somehow gotten messed up after my initial, problematic hibernate to the point where none would stick, even after a reboot. Manually typing in "dhclient eth0" would get eth0 working, so I decided to add it to the bottom of /etc/rc.local, like in the example on the networking page.
Now, eth0 works after a boot. However, after the daemons load up during the boot process, my computer takes a long time to get to the login prompt (this is relatively speaking, since I am on a SSD and the boot process used to be blazing fast before). I'm pretty sure it's because I added "dhclient eth0" to /etc/rc.local.
I should say that even with these changes, after a hibernate, my eth0 still does not work and if it weren't for the edit to /etc/rc.local, eth0's inet settings would still not stick after a reboot (that is to say, the hibernate does do something to my network settings).
Is this the correct/most efficient way to fix my DHCP problem? Can I fix my "eth0 after hibernate" issue? Also, can I make my DHCP settings boot up without changes to /etc/rc.local so that I can get a fast boot again (still not sure how it was able to work before without my edit)?

IPhoto 8.1.2 doesn't work after reinstalled the OS 10.6.8?

iPhoto 8.1.2 doesn't work after reinstalled OS 10.6.8?

To re-install iPhoto
1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
2. Download it from the App Store to reinstall It's on your Purchases List* there.
For older versions that have been installed from Disk you'll need these additional steps:
2a: On 10.5: Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
2b: On 10.6: Those receipts may be found as follows: In the Finder use the Go menu and select Go To Folder. In the resulting window type
/var/db/receipts/
2c: on 10.7 or later they're at
/private/var/db/receipts
A Finder Window will open at that location and you can remove the iPhoto pkg files.
3. Re-install.
If you purchased an iLife Disk, then iPhoto is on it.
If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
*Sometimes iPhoto is not visible on the Purchases List. it may be hidden. See this article for details on how to unhide it.
http://support.apple.com/kb/HT4928
One question often asked: Will I lose my Photos if I reinstall?
iPhoto the application and the iPhoto Library are two different parts of the iPhoto programme. So, reinstalling the app should not affect the Library. BUT you should always have a back up before doing this kind of work. Always.

Macbook air adoble flash player doesn't work after installation

macbook air adobe flash player doesn't work after installation

If you're sure you've installed the latest version of Flash, take each of the following steps that you haven't already tried. After each step, relaunch Safari and test. For a "missing plug-in" error, start with Step 7. Back up all data before making any changes.
Step 1
You might have to log out or reboot before a Flash update takes effect.
Step 2
In the Safari preference window, select
Privacy ▹ Remove All Website Data
Close the window. Then select
 ▹ System Preferences… ▹ Flash Player ▹ Advanced
and click Delete All. Close the preference pane.
Step 3
If you're only having trouble with YouTube videos, log in to YouTube and load this page. You may see a link with the text "Leave the HTML5 Trial." If so, click that link.
Step 4
If you get a warning of a "blocked" or "outdated" plug-in, then from the menu bar select
 ▹ System Preferences… ▹ Flash Player ▹ Advanced
and click Check Now. Quit and relaunch the browser.
If the warning persists, triple-click anywhere in the line below on this page to select it:
/System/Library/CoreServices/CoreTypes.bundle/Contents/Resources
Right-click or control-click the highlighted text and select
Services ▹ Open
from the contextual menu.* A folder should open. Inside it, there should be a file named "XProtect.meta.plist". If that file is missing and you know why it's missing, restore it from a backup or copy it from another Mac running the same version of OS X. Otherwise, reinstall OS X.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
Step 5
Open this folder as in Step 4:
/Library/Internet Plug-Ins
Delete the following item, or anything with a similar name, if present:
Flash Player (failing).plugin
You may be prompted for your login password.
Step 6
Re-download and reinstall Flash. Download it from the domain "get.adobe.com". Don't click a link from any other website, including this one, because you can't trust links. They may be an attempt to trick you into installing malware masquerading as Flash. Type the address into the browser window. Never download a Flash update from anywhere else.
Step 7
If you get a "missing plug-in" error, select
Safari ▹ Preferences... ▹ Security
from the Safari menu bar and check the box marked
Allow (or Enable) plug-ins
Then click the button marked
Manage Website Settings...
if present and make sure that the website is not blocked for Flash.
Step 8
Select
Safari ▹ Preferences... ▹ Extensions
from the Safari menu bar. If any extensions are installed, disable them.

What can I do if my CD or DVD drive doesn't work properly in Windows 8?

QuestionWhat can I do when if my laptop CD or DVD drive doesn't work properly in Windows 8?
AnswerNote: For help with this issue in Windows 7, please see this article.
To get your CD or DVD drive working correctly, try these suggestions in the order listed.
Reinstall the Driver
Hold the Windows key and press the 'x' key to open a menu in the lower-left. In this menu, select "Device Manager." Expand "DVD/CD-ROM drives." Right-click the entry for the CD/DVD drive nested under "DVD/CD-ROM drives," then select "Uninstall." Finally, restart the computer. The computer will reinstall the drivers for the drive.
Power Cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with some hardware problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Unplug all wires and peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Remove the battery (if the model has a removable battery). If the model does not have a removable battery, check your user's guide to determine if you have a pinhole reset on the bottom. If you do, press this.
Hold down the power button for thirty seconds.
Reattach the battery if removed.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Start the computer and test the drive
Microsoft Fix-it
Your computer may exhibit one or more of the following symptoms:
Your CD or DVD drive no longer appears in Windows
Your CD or DVD drive does not read or write and is shown as disabled
The media in your CD or DVD drive cannot be read
The media cannot be written to a CD or DVD inserted into the drive
You receive an error message about your CD or DVD drive
If any of these symptoms apply to your computer, use Microsoft Fix-it troubleshooter available here.
System Restore
Try using System Restore to restore to the most restore point from before the problem arose.
How To: Understanding System Restore, Refresh, Reset, and, Recovery options in Windows 8 + Video
System Recovery
If the System Restore doesn't solve the issue, you could try a System Reset. Resetting your laptop to its original, out-of-the-box state is a great way to eliminate software as a possible cause of the problem. Note that doing a system reset will return the laptop to its default conditions, completely wiping your data. Information on how to perform a system recovery can be found in your user's guide.
For more information on performing a recovery, see the following article:
How To: Understanding System Restore, Refresh, Reset, and, Recovery options in Windows 8 + Video
Contact Customer Support
If the drive doesn't work after performing a recovery, it may be due to hardware failure. Please call customer support or seek servicing.

See this Microsoft article - http://support.microsoft.com/kb/314060/en-us For ways to fix manually
and/or use the proper microsoft fixit 8.1 and 8 or the other one for Windows 7, Vista, and XP listed below.
(these are from the Microsoft article)
Resolution 2: Use the CD/DVD Fix it troubleshooter
To automatically fix common issues with CD or DVD drives, click Run now, and then follow the on-screen instructions. Windows 8.1 and Windows 8
The Automatically diagnose and fix common problems with CD or DVD drives troubleshooter may automatically fix the problem described in this article.
                                This troubleshooter fixes many problems. learn more
Run now
Windows 7, Windows Vista and Windows XP
The Automatically diagnose and fix common problems with CD or DVD drives troubleshooter may automatically fix the problem described in this article.
                                This troubleshooter fixes many problems. learn more
Run now
If your problem is not solved, try the next
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Dvd/cd player won't work after installing windows 8.1

I recently installed windows 8.1 on my Pavilion All in One Desktop Computer and now the computer won't recognise the DVD/CD player. I have downloaded all current drivers, but still not working. Any ideas?

Hello Gindel95,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how the DVD/CD player will not work after installing Windows 8.1, and I would be happy to assist you! To begin, I will need to ask you a few questions:
What is the Product and Model Number of your desktop computer?
What version of Windows did you have installed on your computer before upgrading to 8.1?
Has your computer completed all of its important Windows Updates?
In the meantime, I recommend following this document on Download or Update Software and Drivers for HP Computers, which should help configure your DVD / CD drive.
Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Internal Microphone doesn't work (after installing Boot Camp 3.1)

I have installed Boot Camp 3.1, and after this installation, my internal mic doesn't work (ONLY IN WINDOWS XP).
I tried to fix the problem with several manners (hardware test in CONTROL PANEL / SOUND .../ VOICE TAB / VOICE RECORDING; reinstalling drivers and hardware etc), but I can't get success (for example, the test results: SORRY, NO SOUND IN MIC...).
On the other hand, when I boot as Mac (Snow Leopard), I can use the mic (in skype, for example), without problem.
I note that ear plug (connector in the back of the iMac) doesn't work too.
Somebody can help me in this case ?
Regards
JGFilho

i got a macbook pro, 2 weeks ago, the 2.53Ghz unibody aluminium, the desing of this mac is great even tough the system specs are really low for the price actually, im happy with it(the hardware)...
The only reason i got this is cause apple claims to support windows, i like Mac OS, but i work on windows i need it... if theres no windows capability in mac i wouldnt ever buy one, so this issue is really bothering me A LOT. my impresions about apple are changing after seing this topic filled with questions and not a single moderator answer, go and check a logitech forum and see how they take care about user problems.

Scan doesn't work after downloading Windows 10

Similar Messages

Maybe you are looking for