Scanner not working properly on Adobe Pro XI

Running Adobe Pro for Mac with OS X 10.9. After installing new Multifunction CANION MG5550 in my network. He is working perfectly as printer and scanner with CANON software.
When scanning from Adobe Pro, scanner is detected, overview scan is done but when real scan is executed and completed, Adobe shuts down. How can I solve this error?

Hello,
Please refer to following article:
Crash using networked scanner | Mac OS 10.9.x
Regards,
Anoop

Similar Messages

  • ATI catalyst drivers not working properly in Mac Pro late 2013

    Hi, I have a 6-core Mac Pro late 2013 with two D500 ATI graphics cards and installed Windows 8.1 Pro through bootcamp. I have installed the bootcamp drivers while in windows installation, however there is a problem opening the Fire Pro drivers (catalyst drivers). I get a message that says something like "there is no option to change so the software will not run". I also tried to download the ATI drivers directly from their site, but still get the same problem.
    This poses a problem for me since I need windows for a specific lighting design software that I work with -Dialux-, and it uses Open GL, which doesn't seem to work in my configuration. Does anyone have any similar problem or solution?
    Please help. Thanks.

    Does the reader show up under USB in System Report?
    If the reader is working properly both the reader and an inserted card will show up.

  • Keypad not working properly on Macbook pro

    The key pad on my MacBook Pro does not work all the time and have had to resort to a separate mouse to be able to scroll etc.
    Any advice please.

    Does it now work only on battery? or using the power supply?
    If only on the power supply use a grounded plug.
    Otherwise try reseating touchpad cable. Post the size and year of your MBP.

  • Epson USB Scanner not working properly after 10.44 update

    After 10.44 update, my Epson 3490 USB Photo scanner has stopped working properly. Is this just another one of those update issues that seem to be reported at the moment. Will someone at Aplle actually fix thisat some point?

    I can't open Epson Scan - it appears in the dock and info bar for about 2 seconds, then quits. I can sometimes open SmartPanel by pushing the scan button on the unit, but then it says "Please install the supported TWAIN driver." Most of the time it appears in the dock and info ba) but doesn't open the window itself. Epson couldn't fix it. It works on a PC, so they said it's a Mac problem.

  • Mercury Transmit not working properly for Premiere Pro in Yosemite for me

    Hi.
    Since I am not in the middle of a big project I consciously updated the OS to Yosemite, and for me everything in I do in Premiere is working fine, except for Mercury Transmit when I have Mercury Playback Engine enabled for the project (It was working in Mavericks). When I do enable it I have a white screen in my second hdmi monitor and Premiere crashes. Whan I have it in software only it works, not very fluid and sometimes the media disconnects for a few seconds, sometimes there's a lag. I have macbook pro retina late 2013, Is it a problem with the Inter Iris graphics card? Will it work with a future update? Thanks for the feedback and keep up the great work!

    Hi,
    Please make sure the default permission of this user’s Calendar is AvailabilityOnly and the user who can view the details of this calendar doesn’t have any permission to this mailbox and Calendar:
    Get-MailboxFolderPermission –Identity UserA:\Calendar | FL
    Get-MailboxPermission –Identity UserA | FL
    If the permission is configured properly, please let all other users to view this user’s calendar in OWA or Outlook online mode to check whether they can view the details or not.
    Thanks,
    Winnie Liang
    TechNet Community Support

  • [Athlon64] CD / DVD not working properly, Neao K8T800 Pro series.

    Hi all,
    I purchased a MSI K8t Neo2 motherboard along with a AMD 64 3200+ (socket 939) in the beginning of May.
    When i installed the parts in my case I experienced some problems getting windows (which I reinstalled) to detect all the Harddrives i had.
    I solved this by putting 3 HDD's on one IDE interface, and 1 on a separate controllercard. on the other IDE interface i put my Sony DRU-700A DVD alone.
    This worked, to a certain extent.. When I place a disc in the DVD, windows gets a hizziefit and starts to lag insanely, when it's finally done, it won't autostart the discs i put in, i can't double-click it from My Computer as i get the error:
    "F:\
    Only part of a ReadProcessMemory or WriteprocessMemory request was completed."
    Doesn't tell me much.. I then try ro right-click F: and select "exlore", AHA! this works. I get into the disc and i can move around in the foldertrees, but it takes time.. My GOD it takes time...
    When i finally reach my destination and try to execute a .exe file, this happens:
    "F:\ is not a valid win32 application".
    At this point one starts to think: "ok.. i know that.. but the exe-file i tried to start IS..."
    NOTE: From time to time i've noticed that it switched between these 2 error messages, i.e i get the "not valid" when trying to start the disc and the "ReadError" when starting a .exe-file, and vice versa.
    I have the latest bios, i have tried adding a LG CD-R/W tp the process and tested if that worked, see results here: www.vikholm.se/say_what.gif     
    I might not be the sharpest tool in the shed, but i know that CAN'T be right?
    I then went into the Device Manager and selected "uninstall" on my Sony DVD, thinking it has to find new hardware on reboot and reinstall it. Windows finds nothing, and i can't seem to get it back again..
    Anyways, i noticed that 2 updates to my mobo was avaliable through MSI Live Update, so i choose the newer one and install it, thinking it might solve this problem.
    Select reboot -> Click "exit now" on firefox.exe  -> run for work as i', late -> come home now just to see that windows did NOT reboot as i got an error code from some exe-file.
    Anyways, reboot properly this time and half-way through the boot up it reboots again, and at the loadingscreen where you can see the biosversion and such it says:
    "Sec Master drive is not ATAPI compatible
    F1 to Resume"
    This is my LG CD-R/W. I press F1 and it boots just fine, and i see that my LG is no longer avaliable in My computer.
    These are my problems.
    To sum things up:
    1. Could it be my mobo that is screwed up in the IDE interfaces?
    2. Could it be my IDE cables? (i don't have any others to try with =( )
    3. I've been in contact with Sony's support, accordign to their firmware testers and producttest programs, my device worked as it should.
    4. Anyone have any tips on how to get my Sonydevice back to windows without reinstalling windows? It not, i'll just have to reinstall.
    5. If all else failes, can anyone lend me a handgun so i can end my misery?
    Thanks a million for reading and if you have the slightest idea of what might fix ANY of the problems stated above, do not hesitate to post. Please.
    Milk and cookies for anyone who helps me solve this 

    Quote from: Tiresmoke on 09-July-05, 01:49:28
    The promise controller is simply there to add to their Sata Raid ability. It is not for opticals.
    Then let's do some RTFM:
    Quote
    Pages 1-2 and 1-3
    Promise 20579 On-Board (Optional)
    >Supports two SATA and one IDE
    -  RAID 0, RAID 1 and RAID 0+1 supported
    -  RAID function work with ATA133+SATA H/D or two SATA H/DConnect up to two SATA devices (such as SATA HDD, CD-ROM, DVD-ROM and
    two ATA133 devices
    > SATA 150MB/s with extensions (SATA II Phase I)
    > RAID Smart function
    > SATA ATAPI device compatible
    That clearly states the ability to get opticals connected. It is admitted, that there only SATA opticals are mentioned.
    Quote
    Page 2-18
    Parallel ATA/Serial ATA RAID Connectors controlled by Promise
    20579: IDE3/SER1/SER2 (Optional)
    The brand new Promise 20579 chipset supports  one IDE connector IDE3 and two
    serial connectors SER1& SER2.
    IDE3 is a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133 controller that provides
    PIO mode and DMA mode 0~5, Bus Master, and Ultra DMA 66/100/133 function. You
    can connect up to 2 hard disk drives---one IDE master and one IDE slave.
    Other devices than HDDs are not mentioned in the IDE3 section.
    Conclusion: According to the documentation, opticals can be connected to the promise controller, at least if they are connected to the SATA-interface.
    Own experiments show:
    If an optical drive is connected to IDE3, the promise controller detects it correctly. If a bootable media is inserted, it is detected as bootable by the controller BIOS.
    An old LD 8240 CD-Writer (only MWDMA2/PIO4 capable) works partly, if attached to IDE3, but there are errors. Playing Audio CDs and DAE generates drop-outs. CD burning results in corrupted data on the media.
    If I connect a LG 4163B DVD-Writer, there are no issues concerning CD-playback or DAE. CD-recording was not tried out. The DVD-RAM feature fails, possibly due to driver interference.
    This shows, that there at least a CD-ROM or DVD-ROM drive (PATA) might work on the promise controller, but that also depends on the drive itself.
    Michael

  • One USB Port not Working Properly on MacBook Pro 3,1

    I have an older macbook 3,1 running Mavericks OS and recently one of my left USB ports has not been:
    1) able to eject external hard drives plugged into it (I have to force eject)-instead it gives me a message that one or more programs may be using it (even though I don't have any programs using it).  The hard drive is being powered by USB has a 3.0 connection although this wasn't a problem in the past... I tried the other USB port and it can eject just fine from that port.
    2)Intermittent communication with mouse.
    Not sure if this is a hardware issue but when I try to run diagnostics on this laptop by holding down the "D" key at startup it doesn't take me to diagnostics. I no longer have the discs for this laptop (containing said hardware test) so I can't boot the diagnostics from that discs. In lieu of a hardware test I opened CONSOLE and did a search for USB and there were a couple of these messages:
    8/29/14 12:13:43.000 AM kernel[0]: **** [IOBluetoothHostControllerUSBTransport][SuspendDevice] -- Suspend -- suspendDeviceCallResult = 0x0000 (kIOReturnSuccess) -- 0xdc00 ****
    Is this a logic board issue? Would rolling my OS back to pre-Mavericks work? The problem didn't emerge right when I updated to Mavericks however I have had luck changing OS stuff (updating or rolling back) with faulty USBs...
    Here are other troubleshooting methods I have attempted with no success:
    -Disk Utlity (repair disk and permissions)
    -RESET PRAM NVRAM
    -Remove battery
    -RESET SMC
    -Shut Down
    -Run Disk Utility @ startup
    I'd love to get access to a Hardware Test compatible with my macbook. The links I have found online are to incomplete files. If someone @ Apple could send some Hardware diagnostics tool my way via a disk image that would be perfect.

    Did you boot into Recovery or try & run OS X Utilities, to attempt a test?
    Depending on the computer, that may be your best bet, short of taking
    the computer to an Apple Store with Genius bar; or to an AASP who is
    trained in Apple repair & testing services.
    A replacement of original install restore DVD with the correct AHT on
    a bootable DVD, could be obtained by contacting Apple support or
    the main online Apple sales, or applecare; there would be a fee.
    They'd need to know the Serial Number and product info, and you'd
    have to provide a form of payment in order to get replacement discs;
    and if the computer is way too old, those may be harder to get now.
    The main system tools could be installed in Recovery partition.
    And Ms Sammit may have answered this.
    Good luck & happy computing!
    edited

  • Sleep mode not working properly on Macbook Pro

    On my Macbook Pro everytime my mac enters sleep mode just the display goes to sleep never the system even after 8 hours. Checked the energy saver setting both display and computer are set to ten minutes. I can also never get the display to wake back up unless i do a hard reset. Any ideas? Thanks!

    Does it now work only on battery? or using the power supply?
    If only on the power supply use a grounded plug.
    Otherwise try reseating touchpad cable. Post the size and year of your MBP.

  • PCMCIA is not working properly on Satellite Pro U200 with Vista

    Hi I have upgraded to Vista home premium on U200 and so far almost everything is fine.
    I do however have 2 issues relating to PCMCIA that are bugging me:
    - Any PCMCIA card inserted causes the machine to slow down drastically and mouse movement etc becomes juddery. This is particularly bad if I insert a Toshiba PCMCIA hard drive or a card reader.
    - I havea PCMCIA digital TV card for which I cannot find Vista drivers. It works fine with the XP drivers however i get awful screeching sounds and high pitched beeps for a minute or so every time I change channel. The card is a generic card from an OEM provider.
    Any help appreciated.

    Did you try to update the BIOS or change the settings in the BIOS?
    The Pro u200 was delivered with Toshiba BIOS I hope
    On the second BIOS page you could try to change the PC card controller mode. Maybe you will notice any improvements.
    For Vista PCMCIA digital TV card driver you should ask the card manufacture or visit the support page sorry this is everything what I can suggest

  • B570 FINGER PRINT SCANNER NOT WORKING PROPERLY?

    I just purchased a Lenovo B570 and the fingerprint scanner doesn't seem to functioning correctly. There are times when I have to scan my finger about 10-12 times before I can get it to work. Then I get frustrated and just enter in my password. I like the feature but it's kind of irritating when it doesn't work right. Is it supposed to be so sensitive? Is there a way to fix it so it wouldn't be so sensitive? Thanks.

    have you tried to update drivers?
    http://consumersupport.lenovo.com/uk/en/DriversDownloads/drivers_list.aspx?CategoryID=91249

  • Digital Cinema Desktop not working properly on MacBook Pro 15"

    I'm having trouble with Digital Cinema Desktop playback on the main LCD screen of my MacBook Pro 15". I have selected Digital Cinema Desktop Playback-Main under the View menu but when I press option+F12 I only get a still frame. If I press space, the audio plays but the video remains as a still frame. If I press the right arrow key and hold it down it will play real time or just frame advance each time I press that key quickly. I have also disable my screen saver as recommended in the FCP help document.
    Any ideas where a hidden setting which will remedy this might be? Should I trash the preferences and reset things?

    View > Video Playback > All Frames.

  • Just upgraded my Cannon MP Navigator App for my multi-purpose printer/scanner not working correctlly

    After upgrading to Yosemite MP Navigator App for my Cannon scanner not working properly, Buttons are not active and do not respond .... it works on my laptop with Mavericks ... I will be reverting back to Mavericks .. I use my Scanner a lot . Apple please fix this problem.

    I have the same problem with a Canon MP530 under Yosemite. I'm not sure why Canon can't get their act together to have updated drivers and software. Very aggravating.
    I can confirm that pmt513's workaround works. That's fine for single pages. But what about batch scanning?
    Here's another partial workaround. The main MP Navigator interface still allows you to do the scanning, both single pages and batches. You just can't save, send, or export those scans. But the temporary files are on your disk in TIF format. If you don't mind taking those and converting them to PDF or JPG (which you can do in Preview), then just look in the following folder to the files:
    ~/Library/Caches/Temporaryitems/MP Navigator 2.2/SCN_MFP
    I have put an alias to it on my desktop so that I can easily access the scans. Be sure to copy the TIF files out before you close (and thus clear) the MP Navigator window as that also clears the files from that cache folder.
    I hope this helps some of you.

  • Adobe Reader XI and Adobe Reader X Pro (Editable PDF Combobox Search is not working properly.)

    I have created Editable PDF using itext(5.3.0) in java. I have used Adobe Reader XI and Adobe Reader X Pro.  But in editable PDF combobox search is  not working properly.
    It's only search first character.

    My (admittedly old and slow) system did this too the first time I opened Reader 11, but it "unfroze" after about fifteen seconds, (an eternity in computing time, I know, but it did eventually open all the way) What you're seeing on the right is the "Tools" panel initializing. That's exactly where mine would freeze up on starting. Once it did finally open fully, I clicked the "Tools" link at the top to close the panel, and I opened and viewed a document that way, then closed reader. Now when I open Reader, the Tools panel doesn't initialize and it opens immediately.
    Reboot and before you open anything else, open Reader. When you open it, DO NOT try to do anything with it until it fully opens, don't click anything, don't try to switch to another app. Give it time to open fully, and then click the Tools link to close it. Then, open and view a document, and close it. Close Reader and reopen it. the Tools panel should remain closed and Reader should open fully immediately.

  • I purchased a new computer and also Adobe acrobat XI Pro.  It has not worked properly.  I uninstalled it and tried to reinstall it, but the computer will not accept the Serial number.  What can I do?

    I purchased a new computer and also Adobe acrobat XI Pro.  It has not worked properly.  I uninstalled it and tried to reinstall it, but the computer will not accept the Serial number.  What can I do?

    Hi,
    Have you tried the help documents below:
    Error "The serial number is not valid for this product" | Creative Suite
    Invalid serial number error
    In case of any other error message, please specify.
    Regards,
    Sheena

  • Adobe Creative Cloud (Desktop) does not work properly. The application is blocked : it could not be launch neither stopped. I'm on MAC Yosemite OS, does anyone know how to remove it properly or to force its stop. It does not appear in the launched applica

    Adobe Creative Cloud (Desktop) does not work properly. The application is blocked : it could not be launch neither stopped. I'm on MAC Yosemite OS, does anyone know how to remove it properly or to force its stop. It does not appear in the launched applications.

    I received no error message. The application was just trying to find applications unsuccessfully.
    I am using MAC OS 10.10.1
    I tried to uninstall the application  but it seems that a kind of deamon is still installed thus providing me to reinstall properly. Do you know where are the elements to remove in order to get my machine just like before ?
    Otherwise I would have to reinstall everything and this would be a pain.
    Thanks for your help.

Maybe you are looking for