Scanner on solaris HELP!!!!

I am running Solaris 10 6/06 and have installed the companion cd as well as someother things (Quake II, QEMU for example). I am trying to set up a USB HP office Jet 5500 all-in-one series. I set it up as a printer but i cant set up the scanner functions. I run the following commands and get the following output:
# /opt/sfw/bin/sane-find-scanner
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a SCSI driver for your SCSI adapter.
found USB scanner (vendor=0x03f0 [hp], product=0x3a11 [officejet 5500 series]) at libusb:/dev/usb:3f0.3a11/0
found USB scanner (vendor=0x046d, product=0x0921, chip=ICM532B) at libusb:/dev/usb:46d.921/0
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# /opt/sfw/bin/scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
As you can see SANE can find the scanner from 'sane-find-scanner' but does not recognize it with 'scanimage -L'. I would greatly appriate any assistance and thank you for reading this.

It seems that you didn't set all the environment variables correctly. Check if the following variables are set correctly:
- ORACLE_HOME
- ORA_NLS33
- LD_LIBRARY_PATH
- PATH

Similar Messages

Download Oracle 10g Character set scanner for Solaris

http://www.oracle.com/technology/software/tech/globalization/index.html
the above link contains only the oracle 9i Character set scanner but I need the Oracle 10g Character set scanner for Solaris
please assist me.

Pl see MOS Doc 745809.1 (Installing and configuring Csscan in 10g and 11g (Database Character Set Scanner)
HTH
Srini

Hi.Since I upgraded to Maverick my scanner which is Fuji Xerox Docuprint CM205 fw could not be used for scanning as mac wouldn't find the scanner.Can anyone help please?

Hi.Since I upgraded to Maverick my scanner which is Fuji Xerox Docuprint CM205 fw could not be used for scanning as mac wouldn't find the scanner.Can anyone help please?

There's an alternative ...
Using Image Capture as a scanner:
Connect the scanner to your Mac whether Wi-Fi or USB.
Launch Image Capture.
Click the very small black box bottom right side of the Image Capture window.
You'll see this pop up menu: Connecting this (device) opens:
You can select a default app to scan (Image Capture) and select a folder from the Imort To pop up menu on the right to save scanned files to.

Scanner Unreachable PLEASE HELP

I am trying to scan something but he gives me this error :
"Scanner communication cannot be established. Ensure your product is powered on, check the connection, and ensure your network is functioning properly. If these conditions are correct, restart the product and try scanning again.
If you installed this printed by IP address, then you might need to update the IP address. Use the Update IP Address item in the Start menu entry for this printer.
If you are running firewall software, it may be blocking scan communication. Please visitwww.hp.com/go/wirelessprinting for help configuring your firewall."
I have windows 8.1 64 bit and that link hp.com/go/wirelessprinting is broken and also the print and scan doctor is broken.
Before this,the scan function was working fine and now is not working too, I can only use the print function wich is working good.I do not have problems with the cables or something else, i`ve checked an re-checked all the wires and restarted the printer several times, I want to say that I am not using and I never used the wireless connection.
Thanks!

Hi @RazvanE39,
Welcome to the HP Forums!
I noticed that you are getting the "scanner communication cannot be established," error with your HP Deskjet 2050 running on Windows 8.1. I am sorry to hear this, but happy to help!
I would recommend to go through the steps indicated in this guide, HP Scan Software Does Not Open or Scan on a Printer Using a USB Connection in Windows. You can also get the HP Print and Scan Doctor at this link. HP Print and Scan Doctor for Windows.
Hope this helps, and have a great day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Scanner unreachable please help me!! :-)

Hello,
I have a Windows 8 system and HP LaserJet 200 Color MPF M276 printer. All of a sudden the printer will not scan documents, but it will print and copy documents just fine. This is the error message I get when trying to print:
"Scanner communication cannot be established. Ensure your product is powered on, check the connection, and ensure your networkis functioning properly. If these conditions are correct, restart the product and try scanning again.
If you installed this printer by IP address, then you might need to update the UP address. Use the Update IP Address item in the Start menue entry for this printer.
If you are running firewall software, it may be blocking scan communication. Please visit .... to congigure your firewall."
Please help! Thank you so much!

Hi @ashneedshphelp ,
I see that you are getting a communication error when trying to scan. I will certainly do my best to help you.
You can always restore your computer back to a earlier time when everything was working properly.
How to refresh, reset, or restore your PC on Windows 8.
If you would prefer not to do the System Restore, download and run the Print and Scan Doctor. It will diagnose the issue and might automatically resolve it. Find and fix common printer problems using HP diagnostic tools for Windows?
Check the Windows Image Acquisition (WIA) services:
Click the Windows icon (), type services.msc in the Search programs and files box, and then click the services.msc link under Programs. If prompted, click Yes.
In the Services window, right-click Windows Image Acquisition (WIA) service, and then click Properties.
Click the Dependencies tab.
Make sure that Remote Procedure Call (RPC) and Shell Hardware Detection are listed, and then close the Properties window.
In the main Services window, make sure that Remote Procedure Call (RPC) and Shell Hardware Detection show as Started in the Status column. If they do not, continue to the next step to start the service.
In the Services window, right-click Windows Image Acquisition.
If the option to start the service is available, click Start.
If the option to stop the service is available, click Stop. When the service stops, right-click Windows Image Acquisition (WIA) again, and then start the service.
Close the Services window.
You might have to configure the firewall.
Configuring a Firewall to Allow a Connection with the All-in-One in Windows.
Try and scan again.
What were the results when you ran the Print and Scan Doctor? (did it print or scan, any error messages)
How is the printer connected? (USB/Ethernet/Wireless)
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

No luck to start solaris help please?

hi,
i wiped my hard disk twice, and installed the solaris 10 11/06 x86 six times but still problem, i installed the solaris in the first partiton of the primary IDE master, the partition is bootable, the installation process compleled with final installation of boot blocks and the message was "installaion completed" and prompt me to reboot the system, but after reboot i got the black screen with this message:
Bad PRB sig.
i booted the solaris dvd in the single user mode, the system was mounted under /a, and installed the grub to the MBR with this command:
/sbin/installgrub -m /boot/grub/stage1 /boot/grub/stage2 /dev/rdsk/c0d0s0
The installation asked me for overriting of the MBR, my answer was "yes" and the ouput wass successful without any error message, but when i reboot the system , at this time i got the back screen with the grub word and a blanking cursor, not at least the grub prompt.
i installed the fedora in the other partition and the grub to the MBR and add the solaris to the fedora grub:
title solaris
root (hd0,0)
chainloader +1
makeactivera
but still can't boot the solaris and the error is:
Booting solaris
root (hd0,0)
File system type unknown, partition type 0xbf
Error 13: Invalid or unsupported excutable format
please help me is there any way to start solaris?

Solaris version of grub and Linux version appear and behave much the same but they are not interchangeable. Solaris version has enhanced support for both ufs and ext2 and Solaris slices (sub-partitions) whereas Linux version lacks all these features. Both versions can competently boot Windows by chain loading (pointing Windows boot partition) since all Windows contains its Windows specific boot loader (typically ntldr) pointer within its PBR (partition boot record).
If you use Solaris grub to boot Linux, then Linux grub must be embedded in Linux PBR whereas Solaris one on MBR as follows:
# grub
grub> find /boot/grub/stage1
(hd0,1,a) this answer from grub may be different_
grub> root (hd0,1,a)
filesystem is ufs, partition type 0xbf
grub> setup (hd0)
Checking if boot/grub/stage1 exists...yes
Checking if boot/grub/stage2 exists...yes
Checking if boot/grub/e2fs_stage1_5 exists...yes
Running embed /boot/grub/e2fs_stage1_5(hd0)...16 sectors
are embedded... succeeded
Running install /boot/grub/stage1(hd0) (hd0)1+16p (hd0,1,a)
/boot/grub/stage2/boot/grub/menu.lst... succeeded
Done.
grub> quit
# reboot
Pinecloud,

Canon MP600 scanner not working - help!!

I have a Canon MP600 scanner/copier/printer. It's connected to my MacBook which I purchased in Sept 2007. I have 10.5.2 on my computer. Computer's HD failed after 4 months, then flex cable (BUS cable?) had to be replaced about a week ago. Scanner worked fine before 10.5.2 and the hard driver failing.
Scanner scans the document, but a screen pops up on the computer that says "Unable to save file. The system cannot find the path specified."
I've updated and installed all the drivers from Canon's website. I cannot figure out what is causing the problem, or how to rectify it?
Please offer any help you can. Thanks!

Hi all,
I had the same issue with a Canon MP600. Printing
did work, but it refused to scan with scanner not connected
message.
I updated all the drivers, no luck.
As a last resort, I changed the USB cable to a certified
USB 2.0 high speed one and it started scanning
I would suggest to try the following procedures:
- find a USB high speed cable
- connect just the mac and the printer
- test
If it it works it might be the old cable or some
interference with another USB device.
Reconnecting one at a time the other devices will
be the final step .
If it does not work also after having updated the
drivers and standalone with a Hi-speed USB cable
I have no additional clues, sorry.
Hope it helps

Solaris Help

Hi
I am having much experince oracle in windows enivronment . But In solaris i dont have.My new project full and full based on solaris only. I want the basic commands and related thing to handle oracle in solaris .pls help me
thanks in advance.
null

http://docs.sun.com/app/docs
would be a good place to start off with...
Since you have not mentioned about the Oracle version..
http://www.dbspecialists.com/presentations/oracle817solaris.html

Since upgrading my Macbook pro with Yosemite, I have problem with my Xerox Work Centre 3045 - the printer works normally but it does not recognise the scanner, can you help with this?

Since upgrading my Mac book pro with Yosemite, I have problems with my Xerox Work Centre 3045 printer. The printer works normally but it does not recognise scanner, I can not scan anything. Can you help?

Open Disk Utility and select your hard drive, then Repair Permissions, it will probably return a very large number of errors, primarily printer and library errors, so run it a second time. Then restart the MacBook Pro. If it still will not scan, try using Image Capture from Finder > Applications and see if that will work. If not, contact Xerox about updated drivers.

Help using scanner.class someone help me

ive been working on some code and the thing is i am stuck on how do i count the number of intergers between 1 and 5. for example lets say i inputted using a scanner.class 1,2,2,3,3,3 i want my program to then say how many 2's I have entered and and how many 3's i have entered. So basically if using a scanner.class (keyboard class) in java instead of hardwiring the numbers into an array how do i count out the number of intergers and display them in my output

hardwiring the numbers into an array how do i count
out the number of intergers and display them in my
outputTry this.
        Scanner sc = new Scanner(System.in);
        System.out.println("Enter numbers:");
        int i = 0;
        int count = 0;
        Map <Integer, Integer> intMap = new TreeMap <Integer, Integer>();
        while( true ) {
            i = sc.nextInt();
            if(i < 0 || i > 5) break;
            // Code to count the numbers entered.
            if(intMap.containsKey(new Integer(i))) {
                count = intMap.get(new Integer(i)).intValue();
                count++;
            } else {
                count = 1;
            intMap.put(new Integer(i), new Integer(count));
        System.out.println(intMap);At forum users: Pardon me for all my variable names and poor coding style and lack of comments and...

Again - compilation under solaris - help!

Hi all
I'm trying to compile the following test code:
#include <occi.h>
#include <iostream>
using namespace std;
using namespace oracle::occi;
int main(int argc, char ** argv)
Environment *env;
Connection * conn;
try{
env = Environment::createEnvironment();
conn = env->createConnection(user, pass, sid);
env->terminateConnection(conn);
Environment::terminateEnvironment(env);
} catch (SQLException &e) {
cout<<"Exception: %s\n", e.getNLSMessage(env).c_str();
return 0;
My system is Solaris 9 sparc 64-bit
Oracle Database 10.1.0.2
I run this command:
CC -I/u00/oracle/product/10.1.0/db_1/rdbms/public -L/u00/oracle/product/10.1.0/db_1/lib -locci10 test.cpp
and get the famous error
Undefined first referenced
symbol in file
void oracle::occi::Environment::terminateEnvironment(oracle::occi::Environment*) test.o
oracle::occi::Environment*oracle::occi::Environment::createEnvironment(oracle::occi::Environment::Mode,void*,void*(*)(void*,unsigned),void*(*)(void*,void*,unsigned),void(*)(void*,void*)) test.o
oracle::occi::__RTTI__1nGoracleEocciMSQdDLException_ test.o
[Hint: static member oracle::occi::__RTTI__1nGoracleEocciMSQdDLException_ must be defined in the program]
ld: fatal: Symbol referencing errors. No output written to a.out
I've tried to use:
gcc 3.4.2
Sun Forte 6.0
Sun Forte 6.2
Sun Forte 7
Sun Studio 10
all the same
if I set LD_LIBRARY_PATH and try to link with *.so library - it gives me "wrong ELF class: ELFCLASS64"
I've tried to install and use Client 10.2 - no effect
Under Windows it works perfectly.
What should I do to make this thing compile under Solaris?
Message was edited by:
[email protected]
Message was edited by:
[email protected]

If you want your application to be 32 bit
- use Sun Forte 6.2 and link with OCCI library under $ORACLE_HOME/lib32
If you want your application to be 64 bit
- use Sun Forte 8 and link with libraries under $ORACLE_HOME/lib
( You should be passing the 64 bit compile flag "-xarch=v9" )

Xerox Phaser 6121MFP: Can not set up scanner..Please help

Hi
I am trying to set up scan function from Xerox Phaser 6121MFP to iMac runing Lion 10.7.2. I have managed to set up the printing but just cant set up the scan funtions. I have downloaded and installed drivers for 10.7 from xerox website.
I have downloaded vuescan and that says no scanner connected when I open it and Image capture says no device connected.
I am new to iMac so please be gentle with the instructions!
Thanks in advance.

Hi
I am trying to set up scan function from Xerox Phaser 6121MFP to iMac runing Lion 10.7.2. I have managed to set up the printing but just cant set up the scan funtions. I have downloaded and installed drivers for 10.7 from xerox website.
I have downloaded vuescan and that says no scanner connected when I open it and Image capture says no device connected.
I am new to iMac so please be gentle with the instructions!
Thanks in advance.

Scanner not foud - help

Scanner not dound windows 8 Acobat XI

Obtain and install your scanner's updated TWAIN driver. That is what Acrobat "looks for" and needs.
Be well...

I bought a scanner hp m1005 but cant use that on my macbook pro any help

hi folks hope doing good i need a help of you people. i bough a hp printer and scanner model m1005 fe weeks ago i can use printer on my mac but can use scanner so can any one helps me that i can use scanner aswell pls help if you know anything thanks folks

For that model, Epson has this information:
ICA Scanner Driver
07/17/12
Description: The latest Mac OS X ICA scanner driver for your Epson product is available only via Apple's Software Update. Here's how to get it:
1. Connect the all-in-one or scanner to your Mac and power it on.
2. Select the  menu, then Software Update.
3. Follow the on-screen instructions to install the available updates.
Note: Software Updates may find multiple updates for your system. You may choose to install all or some of the updates by clicking on Show Details.
Compatible Systems: Mac OS X (v10.8.x)

Dont work driver on Scanner ScanJet 300 on winows 7

Please, create new drivers for Scanner ScanJet 300 on Windows 7 platform. I have this divace. Dont work it on Windows 7. Windows 7 and drivers of ScanJet 300 scanner are not complianted.

Hi @Per-Morten
I suspect your question would be better answered in the HP Enterprise Business Community, as your HP Printer is a commercial model.
My technical expertise is with consumer products and software, I am sure the commercial folks would be happy to help if you re-post your question for them to answer. The HP Enterprise Business Community is an HP Forum designed for the Commercial and Enterprise customers to help one another. I am sure you will find some HP folks there to help too.
Click here to view the Printing and Digital Imaging. When the page opens you will see the option to 'Log in' or 'Register Now' on the right. The commercial forums are separate from the consumer boards, thus you will need to register if you don't already have a commercial account.
You may find the HP Scanjet 5400c Scanner Drivers page helpful while you wait for somebody in the commercial Forum to respond to your inquiry.
Best of luck.
- In support of Movember
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Scanner on solaris HELP!!!!

Similar Messages

Maybe you are looking for