[scanner] sane: every second scan fails

Hi everybody,
I got a Canon MP510. I'm already in the group 'scanner' and using sane to scan images:
scanimage --format=tiff >image.tiff
scanimage -L shows:
device `pixma:05B43737_53450F' is a CANON Canon PIXMA MP510 multi-function peripheral
Every second time I get an error:
scanimage: sane_read: Error during device I/O
So i have to scan everything twice.
dmesg says:
usb 1-3: usbfs: interface 1 claimed by usblp while 'scanimage' sets config #1
'rmmod usblp' has no effect. /etc/sane.d/canon.conf seems to be ok.
so what is the problem?

Once I had a issue like yours, so I decided to go merciless against dll.conf. I deleted every single line which wasn't required by my scanner and problem solved.
p.s. check sane's man page about SANE_DEBUG env variable. It will help a lot debugging sane issues.
Luck

Similar Messages

SA 520 error every 10 seconds: sqlite3QueryResGet failed.Query:SELECT * FROM networkInterface WHERE interfaceName=\'bdg1\

Hi all,
On a SA 520 I got this error, every 10 seconds:
sqlite3QueryResGet failed.Query:SELECT * FROM networkInterface WHERE interfaceName=\'bdg1\
Internet access was very spoty and I couldn't reach the firewall administration on the LAN interface. Had to shutdown the appliance to get it working again.
Firmware version is 2.1.7.1
What could have happenend?
With kind regards,
Jeroen

Hi, everything in the "Quick Reference" section should be commented out with ;
You should change those settings further down in the php.ini file.
Example:
error_reporting = E_ALL & ~E_DEPRECATED & ~E_STRICT
display_errors = Off
Last edited by adrianx (2013-07-26 12:32:02)

Canon Pixma MP470 all in one scanner printer "scan fail"

I found earlier posts that described similar problems as mine, they were marked as answered. I continue to have problems even tho I have followed earlier instructions from other members i.e. PAHU.
I am trying to use a Canon MP470 printer connected by USB cable to my iMac. I don't use it much and it has worked unreliably in the past. Today all scans fail except one which to me would mean that I have installed the correct driver for OSX 10.6. I am not sure if I have deleted the old preset and created a new preset for the new driver correctly. I hate to say it but I am a little unsure how to go about this. I don't remember having as much trouble before I upgraded to OS 10.6.3.
If anyone has some suggestions or instructions, I sure would appreciate them.

Okay, the Presets in this post did refer to the Printer preset. The poster had a black and white preset they had created with a previous OS and was trying to use it on Snow Leopard, which did not work because the printer driver was different on the new OS. This does not apply to the scanner portion of your MP470.
As for checking the scanner driver version, this is not an easy task. But the new driver installation typically overwrites the previous version. If you are not sure which driver install you did last, I suggest you run this v13.9 installer again. to ensure it is what you are using.
I would also suggest you have MP Navigator v2.04 or later installed, as earlier versions may not be that compatible with Snow Leopard. Again, running the newest version of MP Navigator installer should overwrite an older version.
If you have the latest MP Navigator and it is still not scanning correctly then please reply. At least you now know about Image Capture so if you did find that MP Nav stopped working, you are not totally stumped
Pahu

Netctl-auto fails every second boot

So, since about two oder three days ago, my netctl-auto fails every second boot and I can't even enable a profile manually.
I already found this thread: https://bbs.archlinux.org/viewtopic.php?pid=1275755
But I checked and don't have any failed units and dhcpcd is not running.
I will do some further investigation and post it here. Any ideas for solutions are welcome
Wolle

I've been having the same problem as well, it boots up just fine then after a reboot netctl-auto fails which had been going on for me for the past 30 minutes without "fixing" itself.
After I added the line:
TimeoutDHCP=30
to my profile then rebooted, it worked. It could be a fluke "fix" but worth a try. I *think* the reason it worked is that the default timeout is 10 seconds which might not be enough to establish a connection for some routers/network cards.
EDIT: I did another boot to see if it was a fluke, and it was. I'm getting a little tired of netctl-auto... I'm going to just disable it and manually do a "netctl start <profile>" after I boot up.
Last edited by DukeH (2013-07-16 19:07:58)

I have 10.9.1 OS and I have a HP deskjet 5440 scanner. I can scan anything to my computer but cannet send it anywhere. Every time I tgry to send , a box comes up saying the file may be read only. I usually try to save to desktop as pdf. Won't alln scanner

I have 10.9.1 OS and a HP deskjet 5440 scanner. I can scan anything to the computer, but cannot save it or send it anywhere. I tried to save to my desktop as PDF and wouldn't and I also tried to send as attachment to email and it wouldn't. Any suggestions/

I have a similar problem. Did you ever find a solution?

Image Capture shuts down scanner after every scan

Image capture could speed up the process of scanning old photos, but it insists on shutting down the Epson V100 scanner immediately after scanning. Have searched for a solution here and elsewhere; am I missing something to adjust the settings? This should be very easy, but I can not get it to work.
There are no control panel settings.
There is no preference panel for Image Capture.
There is no update for the scanner driver.
Epson scan will only scan one photo at a time, so it does not help.
Any suggestions?

Apple's official documentation only provides an information about printing by using this device - scanner is not listed. I would suggest to look for specific drivers on Canon's official webpage.
OS X: Printer and scanner software available for download - Apple Support

Scanning failed

i am using a kodak i40 scanner. when i scan a document in (150dpi, grayscale, simplex) thru kodak's scan validation tool, it works great.
when i switch to acrobate 8.1.2 pro, it get one of two messages: scanning failed or file cannot be found. the page feeds thru ok, pauses 3 - 4 seconds, then the error messages. I've tried this with both hiding and using the scanners native interface. \
I've tested scanning directly into adobe photoshop also. no problems.
this seems isolated to acrobate 8 professional. i purchased full pro edition. i was using acrobat 5.0 without any problems, with this scanner.
I am using the same setup with a panasonic KV-S1025C and no problems. I prefer the i40 for a number of reasons, depending on the job, so reverting everything to the panasonic is not desired.
any suggestions?
roxylee

I had found your step 1 in a thread online before my post on this forum. It did allow the install to continue, but at the end of the process I could not connect to the printer.
After using the MS Fix-it in step 2, the install was successful.
Thank you!
moreamused

Overview Scan failed to complete

Suddenly I can no longer scan and get a prompt that says 'The overview scan failed to complete'. I rarely use my scanner and have had a couple of updates that may have blocked my ability to scan as I was having no problem a few weeks ago. No problem printing. Suggestions?

Hello , Welcome to the HP Support Forums!
I understand that you are no longer able to scan from your HP Officejet 6600 e-All-in-One Printer to your Mac OS X 10.9 computer. I would like to assist you today with resolving this issue. Can I please have you follow the steps below to correct any software or driver conflicts that a computer update may have caused. Step 1: Reset the Print System: To start, I am going to have you Reset the Print System on your Mac as it is important that we have a nice clean slate to work with for troubleshooting. Please click here for instructions on how to perform the Reset. When the website opens follow the steps under 'Resetting the printing system in OS X Lion' as the steps are the same for your Mac OS X 10.9 Operating System. This Reset will remove every printer from your Mac. However, it does not uninstall the printers. Therefore, should you use other printers on this Mac, once the Reset is complete simply ensure that the printers are connected via a USB Cable or Network connected and (+) Add them back in. Do not add your HP Officejet back in at this time. Once the reset is complete, please proceed to the next step. Step 2: Uninstall Drivers and Software: Next, please click here for steps on how to properly uninstall your printer. Once the site opens select the dropdown for 'Mac OS X v10.6, OS X v10.7, OS X v10.8, and OS X v10.9' and follow the steps to complete the uninstall process. Once the uninstall is complete, please continue on. Step 3: Verify and Repair your Disk Permissions on the Mac:
Open Macintosh HD and go to ApplicationsGo to the Utilities FolderOpen the Disk UtilitySelect the Hard Drive volume you are using (usually on the left)Select Verify Disk PermissionsOnce that process is done, select Repair Disk Permissions Step 4: Check for Apple Updates: Go to AppleSelect System PreferencesSelect Software UpdateClick Update NowInstall your available updatesRestart your computer Step 5: Install Device: Please click here to download the latest drivers for your OfficejetOnce the website opens please select the Download button on the top leftOnce the download is complete please follow the onscreen instructions to reinstall your printer Once your printer has been successfully reinstalled, please test the scanning function again. Please respond to this post with the result of your troubleshooting. Best of luck!

Why arch always access ext4 every second?

I've read one related topic https://bbs.archlinux.org/viewtopic.php?id=113516.
$ pacman -Q linux
linux 3.10.10-1
$ mount -o defaults,noatime,commit=60 /dev/sdb2 /mnt/home
# it access my disk every second
$ mount | grep sdb2
/dev/sdb2 on /mnt/home type ext4 (rw,noatime,commit=60,data=ordered)
Any tip to debug it?

> f it has just been created, the link you posted may contain the answer i.e. it might still be creating the inodes.
Thanks, I just notice it
man mkfs.ext4
# default enabled lazy_itable_init and lazy_journal_init.
# and related mount option: uninit_bg
But how to know all the inode have already created?
Here I list my another PC's ext4 partition information.
$ smartctl --all /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.10.10-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HITACHI HDS7225SCSUN250G 0710B99GZK
Serial Number: VFA140R1D99GZK
LU WWN Device Id: 5 000cca 210d25271
Firmware Version: V5DOA7BA
User Capacity: 250,056,000,000 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 1
Local Time is: Tue Sep 17 10:03:25 2013 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4949) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 83) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 161 161 050 Pre-fail Offline - 195
3 Spin_Up_Time 0x0007 135 135 024 Pre-fail Always - 260 (Average 292)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 73
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 134 134 020 Pre-fail Offline - 32
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 32356
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 73
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 208
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 208
194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 17/54)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
$ tune2fs -l /dev/sda2
tune2fs 1.42.8 (20-Jun-2013)
Filesystem volume name: arch64
Last mounted on: /
Filesystem UUID: xxx(omit)
Filesystem magic number: 0xEF53
Filesystem revision #: 1 (dynamic)
Filesystem features: has_journal ext_attr resize_inode dir_index filetype needs_recovery extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize
Filesystem flags: signed_directory_hash
Default mount options: (none)
Filesystem state: clean
Errors behavior: Continue
Filesystem OS type: Linux
Inode count: 15138816
Block count: 60548805
Reserved block count: 3027440
Free blocks: 8208333
Free inodes: 12058767
First block: 0
Block size: 4096
Fragment size: 4096
Reserved GDT blocks: 1009
Blocks per group: 32768
Fragments per group: 32768
Inodes per group: 8192
Inode blocks per group: 512
Flex block group size: 16
Filesystem created: Thu Jan 5 17:01:16 2012
Last mount time: Mon Sep 2 08:58:15 2013
Last write time: Mon Sep 2 08:58:15 2013
Mount count: 12
Maximum mount count: 34
Last checked: Fri Jul 12 11:00:12 2013
Check interval: 15552000 (6 months)
Next check after: Wed Jan 8 11:00:12 2014
Lifetime writes: 1724 GB
Reserved blocks uid: 0 (user root)
Reserved blocks gid: 0 (group root)
First inode: 11
Inode size: 256
Required extra isize: 28
Desired extra isize: 28
Journal inode: 8
First orphan inode: 13159924
Default directory hash: half_md4
Directory Hash Seed: 5deea733-f866-4478-add5-a98235057da4
Journal backup: inode blocks

SQL Server 2014 Always on HA takes 8-14 seconds to fail over. Application side timeouts occur

Hi All,
I have a very similar post in the SQL Server 2014 forums too (https://social.technet.microsoft.com/Forums/sqlserver/en-US/adb5e338-907e-4405-aa62-d3ea93c7a98a/sql-server-2014-always-on-ha-takes-814-seconds-to-fail-over-application-side-timeouts-occur?forum=sqldisasterrecovery) -
advice in the end was to post a question here.
SQL Server Nodes, 2014 (12.0.2480.0)
1 Share witness (on separate subnet)
1 Cluster
1 Listener
I have been testing the response time to failovers – both manual (right-click, fail over in SSMS) and Automatic (shut down the primary host). The way I am testing response is to have a SSMS query running on my desktop, connected to the listener querying
a small table and hit execute.
The Query response time, from execute to receiving the result, has been between 8 and 14 seconds based on my testing. My previous experience (in a separate environment) showed around 2 second fail over times in a very similar configuration.
Availability DB is 200Mb and is not actively used. The nodes are synchronised.
SQL Server Hosts: Windows 2012, 2 cpu, 8gb RAM.
Questions:
1: It’s a big question but what should I expect for a ‘normal’ fail over time. Keep in mind this scenario is about as simple as it gets.
2: As it stands an 8 to 14 second ‘outage’ could cause some applications to time out. Or am I being un-reasonable? I am seeing the very simple query in SSMS to time out with this:
Msg 983, Level 14, State 1, Line 2
Unable to access availability database 'DATABASE' because the database replica is not in the PRIMARY or SECONDARY role. Connections to
an availability database is permitted only when the database replica is in the PRIMARY or SECONDARY role. Try the operation again later.
Cluster logs are long - this section accounts for 8 seconds of the 11 second outage I experienced. I can supply the full log if required. Also this log is just the 2 cluster nodes, I removed the witness share to make sure it was as simple as possible.
00001090.00002128::2015/02/25-03:05:08.255 INFO [GEM] Node 2: Deleting [1:65 , 1:71] (both included) as it has been ack'd by every node
00001ee4.00002130::2015/02/25-03:05:10.107 INFO [RES] Network Name: Agent: Sending request Netname/RecheckConfig to NN:5b81e7bd-58fe-4be9-a68a-c48ba2aa552b:Netbios
00001090.00002128::2015/02/25-03:05:11.888 INFO [GEM] Node 2: Deleting [1:72 , 1:73] (both included) as it has been ack'd by every node
00001090.00002698::2015/02/25-03:05:11.889 INFO [GUM] Node 2: Processing RequestLock 2:49
00001090.00002128::2015/02/25-03:05:11.890 INFO [GUM] Node 2: Processing GrantLock to 2 (sent by 1 gumid: 67)
00001090.00002698::2015/02/25-03:05:11.890 INFO [GUM] Node 2: executing request locally, gumId:68, my action: /dm/update, # of updates: 1
00001090.00002128::2015/02/25-03:05:12.890 INFO [GEM] Node 2: Deleting [1:74 , 1:74] (both included) as it has been ack'd by every node
00001ee4.00002130::2015/02/25-03:05:15.107 INFO [RES] Network Name: Agent: Sending request Netname/RecheckConfig to NN:5b81e7bd-58fe-4be9-a68a-c48ba2aa552b:Netbios
00001090.00002128::2015/02/25-03:05:16.988 INFO [GUM] Node 2: Processing RequestLock 1:28
Thanks in advance.
Keegan

Hi Keegan,
From these event log , what I can see is "Sending request Netname" wasted the time .
Could you please tell us the network configuration of that cluster nodes ?
If I recall correctly , it is recommended to only remain Tcp/IP protocol and disable NetBIOS over TCP/IP for "Private Network" , also do not configure DNS/Wins default gateway for "Private Network" :
https://support.microsoft.com/kb/258750?wa=wsignin1.0
After that please test again .
Best Regards,
Elton JI
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

Scan failed message kodak i40 acrobat 8.0

Ive just purchased Acrobat 8.0. I was using acrobat 5.0 with a Kodak i40 scanner. Scanning directly into acrobat with 5.0 was no problem.
Since uninstalling 5.0 and installeing 8.0 (and rebooting in between), acrobat gives me a scan failed error message, without any details or links.
Kodak supplies a test scan validation program and that works fine, the scans are successful within that program.
Ive downloaded the latest drivers for the scanner, both software and firmware and successfully installed. Ive done a repair reinstall of Acrobat 8.0. None of the steps has had an affect. Kodak tells me its an acrobat problem because the scanner is working fine with the validation tool that they supply.
Any suggestions?
Thanks for the help.
roxylee

The Kodak i40 was QA'd for Acrobat 8 -- do you have all the latest updates? Have you tried the suggestions in the Troubleshooting scanner issues (Acrobat 8 on Windows) at:http://kb.adobe.com/selfservice/viewContent.do?externalId=325262&sliceId=2
One suggestion you might try first is to create a new user account since you've successfully scanned into Acrobat before. Your user account may have since been corrupted, causing problems when you scan. Create a new user account with administrative privileges, and then log into Windows using the new account.

4630 Scan Failed to complete error - OS X Yosemite

I bought the 4630 about a month ago and have tried scanning on 3 different Macs running OSX 10.10.1. The first scan after initial set up works. After that, I get either "The overview scan failed to complete" if the Details window is open or "The scanner failed to complete the scan" if the Details window is hidden. I've tried re-installing the 4630 dozens of times. I just downloaded the last HP software for it. Please help.

Hello @JohnGillen , and thanks for posting on the HP Forums!
I can see you're experiencing scan issues. I'd love to help with that!
I have a few steps I'd recommend:
I would suggest deleting the printer from your print system, using this document: Uninstalling the Printer Software.
Once you have deleted it, I would suggest verifying and repairing the disk permissions: About Disk Utility's Repair Disk Permissions feature.
I would also suggest running your Apple updates: OS X: Updating OS X and Mac App Store apps
After the updates, I would recommend reinstalling the printer: HP Officejet 4630 e-All-in-One Printer series Full Feature Software and Drivers.
Good luck and please let me know how it goes!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

I am getting a pop up on my iPhone 4S asking password of my iCloud even though I feed the password but still keep on asking the same thing every second so I am not able to use my iPhone.

I am getting a pop up on my iPhone 4S asking password of my iCloud even though I feed the password but still keep on asking the same thing every second so I am not able to use my iPhone.at various times it asks different passwords.

Curretly, there is an iCloud blackout. It started this morning around 2AM California time (Pacific), 5AM New York (Eastern). A lot of people have been having issues all day, including me. No iCloud services are online. Even Find My iPhone is down.

ORA-3113 while running export (first run ok, second run fails)

Hi,
I'm running 10g (10.1.0.2.0) on gentoo Linux.
After a restart of the database I can do an EXP for any user without errors. But when I repeat the same command after the export I get the following error:
. . exporting table WEB_SESSION_DATA 0 rows exported
. exporting synonyms
EXP-00008: ORACLE error 3113 encountered
ORA-03113: end-of-file on communication channel
EXP-00000: Export terminated unsuccessfully
It's always the same error on the same task (exporting synonyms) but always just for the second and any later export, while the first one is ok.
I read through some forums and found, that ORA-3113 is a standard error which just hides the real error. So I look into the trace files and found:
ksedmp: internal or fatal error
ORA-07445: exception encountered: core dump [jox_lookup_known_object()+413] [SIGSEGV] [Address not mapped to object] [0x1AD14034] [] []
Current SQL statement for this session:
SELECT SYNNAM, DBMS_JAVA.LONGNAME(SYNNAM), DBMS_JAVA.LONGNAME(SYNTAB), TABOWN, TABNODE, PUBLIC$, SYNOWN, SYNOWNID, TABOWNID, SYNOBJNO FROM SYS.EXU9SYN WHERE SYNOWNID = :1 ORDER BY SYNTIME
If I call this SQL from sqlplus I get the same ORA-3113, so this seems to be the cause for the export failure.
When I remove the DBMS_JAVA.LONGNAME calls from the statement, it runs fine. It also runs fine, when I add a "and 1=0" to the EXU9SYN view. But this will not really solve the problem, because then all synonyms don't get exported.
I also checked all the synonyms and they are valid, the referenced tables exist and can be queried.
Because we use JavaStoredProcedures I cannot remove the Java Features in Oracle. But I reinstalled it (rmjvm.sql and initjvm.sql) but this did not help.
Does anyone have an idea what's happening here?
Especially the "first run ok, second run fails" seems to be very strange, because DB objects including DBMS_JAVA should be ok, if the first export can be done. So what changes in the database during or after the first run?

Maybe description for bug 3953108 (ORA-7445 AND ORA-3113 DURING DIRECT FULL DATABASE EXPORT OF PUBLIC SYNONYMS) is helpful.
Werner

Virus scan failed Error on deploying a web application having a jar file for calling the applet on the jsp page

Hi,
I have an applet application that i want to deploy on the Oracle cloud.
So i have created a jar file for the applet application and i am using this jar to call the applet on a jsp page.
But when i am delpoying my application on the java cloud, its giving me the below error:
2014-10-28 03:16:41 CDT: Starting action "Virus Scan"
2014-10-28 03:16:41 CDT: Virus Scan started
2014-10-28 03:16:49 CDT: ----------------------------------------------------------------------
2014-10-28 03:16:49 CDT: File Scanned: "Application7.ear".
2014-10-28 03:16:49 CDT: File Size: "106698122".
2014-10-28 03:16:49 CDT: File Status: "INFECTED".
2014-10-28 03:16:49 CDT: ----------------------------------------------------------------------
2014-10-28 03:16:49 CDT: Virus scan failed.
2014-10-28 03:16:49 CDT: "Virus Scan" complete: status FAILED
Can't we deploy any application having applet or swing component's onto the cloud?
Or do we need to request for any extra permissions for the same?
Thanks,
Manoj

I don't see applets mentioned in the supported features nor in the unsupported features so not sure if they are supported you would likely need to contact the operations team to confirm.
Jani Rautiainen
Fusion Applications Developer Relations
https://blogs.oracle.com/fadevrel/

[scanner] sane: every second scan fails

Similar Messages

Maybe you are looking for