SCB-68 Pin#8 (+5V) not working

Hello,
I am using PCIe-6321 DAQ and SCB-68 connector block to connect two stepper motor drivers and drive the stepper motors. I need to provide +5 volts to my driver in order to power the emitter diode in the opto-isolators in the drivers. I am able to get +5 volts from pin 14 of the SCB-68 but I am unable to get the +5 volts from the SCB-68. The Quick Reference Lable states the pin 8 as +5V, Fused. Can anyone suggest me what I am supposed to do in order to obtain the +5 volts from pin 8 of the SCB-68.
Thanks,
Bharath J S

So you can read 5V from pin 14, just not pin 8? You may have a blown fuse on your DAQ board. I'm not sure if there are seperate fuses for each output.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Similar Messages

Lightning to 30-pin adapter not working w/iHome/iPhone 6.

Lightning to 30-pin adapter is not working correctly with iHome/iPhone 6. When I plug phone in the music and time update will work but it won't charge the phone, unless I turn my phone around but then music won't work. I've only had my iHome for a year and used it with no problem with my 4S. Now that I have the iPhone 6 I decided to get the adapter so I wouldn't have to spend money on a new iHome. I thought I just had a bad adapter, at least that's what they told me in the Apple Store. So I exhanged it at Best Buy, where I bought it, and got another one. Very disappointed that I have the same problem. Anyone else have this problem? Did I just wain't $30.

No-one from Apple here
It is either a corrupt update to iOS
or something in Honda that no longer likes iOS 8.3
To eliminate an issue with iOS 8.3 basic troubleshooting
Restart
Reset
Restore ,as new ,check iPhone functions if working correctly then restore your back up to get back to normal
If still an issue you then need to eliminate the potential Honda side,2007 is very old technology compared to 8.3

Lightning to 30-pin Adapter not work properly with iPhone 5s

Lightning to 30-pin Adapter (0.2 m) with iPhone 5s working good with power adapter and 30-pin cable, but how iPhone at 100% power, I see message "This accessories is not working correctly".
But with iPad mini 1 everything is OK.

Bottom line, the iPhone case restricted insertion of the 8 pin adapter into the IPhone. Slide in cases with open bottoms have no problems but wrap around cases can restrict flush insertion due to insufficient access to the recepticle in the iPhone.

Hp photosmart 6525 icon pinned taskbar not working

printer icon pinned to taskbar suddenly stopped opening the window for choices of what you wanted to do with your printer, and now just displays the following window...

Hey there @Bloodstone422
Welcome to the forums
I saw your post about the software no longer opening up on your system and I will surely do my best to help! It appears as though the software isn't completely installed, and am not quite sure what could have happened. However, I would suggest clicking on the option to "Connect a new printer", and try running through the setup again.
Let me know what happens and we will go from there!
Good luck
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Lightening to 30 pin adapter not working, but was working before

I have a 7th generation ipod nano. I have a lightening adapter that was working with an older system and now is no longer recognizing the device. I am getting the infamous not compatible message. Any ideas?

Well I was wrong it's got nothing to do with software or a problem with the iPhone 5S, it's the adapter hardware.
I went to the Cribbs Causeway store and was able to replicate the error message on the demo iPhones plugging in the adapter i purchased. So I was given a replacement, tried that with same result on my 5s and the demo phones. Then tried another taken off the shelf just like the previous one and voila it worked. It turns out based on the comments of the guy who served me, that they had seen a few instances of this issue.
I had already logged a case with Apple and they are sending me another cable FOC they are going to try to establish the batches of these adapters that have this problem as they suspect a manufacturing problem
SO, if you have this issue with a recently purchased adapater just take it back to the Apple Store and ask for a replacement.

Certificate Trust (pinning rules) not work.

Windows 7 SP1 x86, EMET 4.1 U1, IE 11
Stopped working function Certificate Trust (pinning rules).
There are no reports of EMET_Agent you visit the site
that has expired rules. There is only
the message to Event Viewer. How do I fix
this problem to EMET_Agent reported
expired rule at the entrance to the site?

Pin button not working

I watched the video tutorial on how to pin an object to the screen, but when I go to do it the button is greyed out. Why? is there a way you could help me. it’s very frustrating.

Hi GusDoeMatik1
May I know the object that you trying to pin?
Please note that, not all the items can be pinned within muse. For example : If you have placed a slideshow on a page, even though you have option to pin the whole slideshow widget, you might not be able to pin its triggers ( that is thumbnails) Container ( with in which the images are placed ) etc and in such similar cases Pin button remains greyed out.

Yosemite Maps red pin favorites not working

Hello,
I've noticed for a while that some iOS 8 Maps favorites that sync to OS X Yosemite Maps come through as red pins which do nothing when selected in the Maps desktop application.
Any ideas? This makes much of Maps useless.

Triple-click anywhere in the line below on this page to select it:
~/Library/Containers/com.apple.Maps
Right-click or control-click the line and select
Services ▹ Reveal in Finder
from the contextual menu.* A Finder window should open with a folder named "com.apple.Maps" selected. Quit the application if it's running. Move the folder to the Desktop, leaving the window open. Relaunch the application and test. If there's no change, quit again and put the item you moved back where it was, overwriting the one that may have been created in its place. Otherwise, delete the folder you moved. The list of recent places displayed in Maps will be lost.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

Pin it button not working on all pages!

I have created a personal website using muse, its been published but not pushed live yet, but only three of the buttons works when you hit the pin button on three pages and the others don't work. I have tried this on safari, chrome and firefox. This applies to smartphone and tablets: It popped up with this:
This page at "http://rachelwynn.businesscatalyst.com" says: Sorry, couldn't find any pinnable things on this page.
Also I want to use pinterest analytics to gain data from my website I can do it two ways:
Add this meta tag to the <head> of your index.html file or equivalent
<meta name="p:domain_verify" content="6b81c0acb133f1f02a9df81ce5bc25af"/>
or
Upload this file (pinterest-6b81c.html) to www.rachelwynn.co.uk
How do I do that? And when do i do that, before i push the site live or through the manage system on business catalyst. I will be putting it through business catalyst rather than a hosting company and linking it to my domain name url: www.rachelwynn.co.uk.
Currently my behance prosite is linked to the above url.
Appreciate any help here!
Wynnit

Hi Wynnit,
Pinning will not work in most devices - desktop only. To do the same in your device layouts you need to use the scroll motion tools.
To add code to the <head> tags in Muse you go to your page properties and under the meta tab you will see a section you can paste your code.
When you do push live with Business Catalyst you will be given prompts as to how to go about it.

30 pin lightning converter suddenly not working properly in my car

I have a Hyundai Veracruz that has the Hyundai cord that you plug into your phone and can play music/podcasts through the speakers while charging the phone. Of course, when I traded in my iphone 4s for the 5s a few weeks back, I had the problem that the Hyundai cord was compatible with the 30 pin plug. I ended up getting the lighning to 30 pin adapter (not the one with the cord, the regular little one. I tried the corded lighting to 30 pin adapter first because of the issue with the regular lightning to 30 pin adapter not working if an iphone is in its case, but that product didn't work at all). Anyway, it had been working totally fine-- recognizing the iphone as soon as I plugged it in, playing my music through the speakers, charging it, allowing me to use the controls on my steering wheel to skip songs if I wanted-- until this morning. When I plugged it in this morning, my radio didn't turn on automatically like it always has before. Instead, when I turned it on manually and went to the auxilary mode it just says connected instead of ipod detected or whatever it used to say. The good news is that it still plays through the speakers and charges, but I can't use the controls on the steering wheel and clearly something is wrong. Any ideas?

Hello there, jenniferps.
The following Knowledge Base article reviews some great information about troubleshooting car stereo connections:
iOS: Troubleshooting car stereo connections
http://support.apple.com/kb/TS3581
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

PIN not working

my pin is not working what i have to do? plzz reply

shahzii wrote:
my pin is not working what i have to do?
Please advise your SkypeToGo #.
TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
I recommend that you always run the latest Skype version: Windows & Mac
If my advice helped to fix your issue please mark it as a solution to help others.
Please note that I generally don't respond to unsolicited Private Messages. Thank you.

Edit button not working on a publishing site on sub-level pages only (SP 2010)

When I create a top level page, the Edit button/edit page works fine with checkout and checkin. However, once I create a sub-level page - that is I create a second page within the first page then the edit button does not work and there is a message
displayed on the ribbon in yellow background:
Status:
Published and visible to all readers
I have read all responses to similar posts and tried them but problem is not resolved.
I don't have workflow turned on, I don't have content approval, yet, issue is still there.
Please help.

Hi Wynnit,
Pinning will not work in most devices - desktop only. To do the same in your device layouts you need to use the scroll motion tools.
To add code to the <head> tags in Muse you go to your page properties and under the meta tab you will see a section you can paste your code.
When you do push live with Business Catalyst you will be given prompts as to how to go about it.

Image and Text rollover together not working

Hi,
I am trying to make a simple image thumbnail rollover with a text rollover at the same time. I would like to have the text able to be linked to different areas of my site to the image which is underneath. However I need to have the text cover the whole image area so that it recognises the rollover.
I have done my best to make it work in various ways with different effects but not the way I want it.
Here is the page that has the attempts at what I want.
http://studiotrulytruly02.businesscatalyst.com/design.html
The first one on the left works but I cannot keep the text in the same place on rollover.
The second I have pinned the text box to hold it there but it will not allow the image to have rollover as well. Also pinning does not work as it means when you scroll down the buttons stay there.
The third one works but there is an invisible button above text buttons that is aligned with them and taking you to the wrong place.
What is the correct way to do this?

can you check if ur facetime and imessage has complete the activation?
your current SIM card provides you with international sms function?
if not maybe u can try with a diff SIM?

IPhone 6 pin or fingerprint not working please help me asap

i phone 6 pin and finger print not working please help

Howdy Karan sood,
Welcome to Apple Support Communities.
It sounds like you’re running into an issue unlocking your iPhone because Touch ID and passcode aren’t being accepted.
Take a look at the article linked below, it provides troubleshooting suggestions that’ll resolve most Touch ID issues.
Use Touch ID on iPhone and iPad - Apple Support
Get help with Touch ID
Make sure that you're using the latest version of iOS.
Make sure that your fingers and the Home button are clean and dry.*
Cover the Home button completely. Don't tap too quickly, don't press down hard, and don't move your finger while Touch ID is scanning. Make sure that your finger touches the metal ring around the Home button.
If you're using a case or screen protector, make sure it doesn't cover the Home button or the surrounding ring. If it does, remove the case or screen protector and try again.
Tap Settings > Touch ID & Passcode and make sure that iPhone Unlock or iTunes & App Store is on. Also make sure that you've enrolled one or more fingerprints.
Try enrolling a different finger.
If you can't enroll any of your fingers, take your device to an Apple Retail Store, Apple Authorized Service Provider, or contact AppleCare for help.
* Moisture, lotions, sweat, oils, cuts, or dry skin might affect fingerprint recognition. Certain activities can also temporarily affect fingerprint recognition, including exercising, showering, swimming, cooking, or other conditions or changes that affect your fingerprint.
And, this article provides tips that’ll help resolve passcode issues.
iOS passcodes - Apple Support
Forget your passcode?
If you or someone else enters the wrong passcode too many times, your device will disable itself temporarily. Get help if you forgot your passcode or your device is disabled.
Learn what to do if you forgot your Restrictions passcode.
I hope this helps,
-Jason

How Do I Pin A Tile To My New Tab Page, Instructions On Here Do Not Work.

These new FF updates are going to drive me to drink. It's a simple question, one would think, yet I cannot find the answer. FF29 has "tiles", I suppose they are called, when you click on "new tab page". At one point, I had them all on there...how, I don't remember.
Now, my "tiles" are disappearing. I have changed NOTHING. How do I re-add the websites I want to those tiles?
Before someone gives me the generic answer with the link, I will tell you that I already went to this link: https://support.mozilla.org/en-US/kb/new-tab-page-show-hide-and-customize-top-sites
Those instructions do not work. I do not have any little pin in those squares. When I go to a website that I usually go to, the only option I get is "Pin Tab" but that only adds a tab at the top of the browser window, it does NOT add it to the tiles, like I want.
I've tried the "Show All Bookmarks" route, and tried to drag the bookmark to a tile, it does NOT work.
There are 9 tiles. If I want to change them around, or re-add the 4 that have mysteriously disappeared today, HOW do I do that? Again, those blank tiles do NOT show a "pin" anywhere. They were set up, then they started to disappear. Again, I've changed NOTHING. It should not be this difficult to add a website to my tiles on my new tab page.

What troubleshooting information would you like. I posed a question, you tell me what you would like to see.
I know how to open my about:config, this isn't my first time on the internet.
You said: "You can check the browser.newtab.url pref on the about:config page to see if it still has the default about:newtab value."
Yes, it does. What else would you like to know so that this can be fixed?
I also stated in my very first post that the link you just linked to, (that I also linked to so everyone was aware of what link I'm talking about), I already tried and it doesn't work. Do you guys even read what we put up or do you just hand out random, generic answers?

Safari 8 hover does not work over google map location pins

OS X 10.10.1, Safari 8, Java 8-25
I have always had little odd things not work when using safari on a large % of websites I visit, the latest issues are
no response when hovering over google map location pins, travel site calendars not opening or responding to mouse, drag and drop
show the item being dragged several inches away from the actual pointer, some links don't respond, missing items
or odd layout with print or pop ups going off the screen on some website pages, zooming in and out does not help. I have none
of these issues when using Firefox or Chrome. Been using Safari for 4 years now.

Have you tried a PRAM and an SMC reset? They're longshots, but don't take long to try.
PRAM: http://support.apple.com/kb/HT1379
SMC: http://support.apple.com/kb/HT3964
Have you run Apple Diagnostics from the disc(s) that shipped with the computer?
Since the problem occurs in all browsers, it still sounds like a video hardware or video RAM or maybe a software issue having to do with layers and rendering.
The map layers aren't getting rendered, or if rendered, aren't getting displayed.
Do you have any browser add-ins? Pop-up blockers?
Since you have two video chipsets, it's possible that might be related to the issue.
This non-Apple website talks about switching between chipsets on the various MacBook models so equipped, and points to a free 'donationware' program for the menubar that lets you easily switch between chipsets:
http://www.everymac.com/systems/apple/macbook_pro/macbook-pro-unibody-faq/macboo k-pro-unibody-switching-between-graphics-processors.html
Trying to think of other software that might help pinpoint the problem, does the iPhoto Slideshow 'Shatter' template work? Working properly, it 'shatters' images into several color layers and rotates them in and out to build and deconstruct photos.

SCB-68 Pin#8 (+5V) not working

Similar Messages

Maybe you are looking for