Sccheck fails with connection refused
I have a 2 node cluster that was just upgraded from SC3.0 to SC3.1u4 (8/05). sccheck passes on node aemhrsDV1 and fails with the following message on aemhrsDV2:
root@aemhrsDV2 # sccheck -b -v2 -h aemhrsDV2
sccheck: Requesting explorer data and node report from aemhrsDV2.
sccheck: aemhrsDV2 error: Connection refused
sccheck: Unable to run checks on: aemhrsDV2All SC3.1 patches have been applied. All availble agents were updated using 'scinstall -u update -s all' and re-registered. Test ip addresses were supplied during 'scinstall -u update -S interact'.
Both nodes come up fine individually in cluster (through step 10) but together the log /var/cluster/ucmm/ucmm_reconf.log shows:
Thu Aug 9 21:47:04 EST 2007 SUNWscucm.ucmm_reconf udlm started in cmmstep2
Thu Aug 9 21:48:44 EST 2007 SUNWscucm.ucmm_reconf udlm completed successfully in cmmstep2
Thu Aug 9 21:48:44 EST 2007 SUNWscucm.ucmm_reconf cvm started in cmmstep2
Thu Aug 9 21:48:45 EST 2007 SUNWscucm.ucmm_reconf cvm completed successfully in cmmstep2
Thu Aug 9 21:48:45 EST 2007 SUNWscucm.ucmm_reconf ucmm reconfiguration step 2 completed
Thu Aug 9 21:48:45 EST 2007 SUNWscucm.ucmm_reconf Step: cmmreturn CURRNODES=0 1Running scstat -i hangs forever at IPMP Groups with both nodes in cluster but separately displays the adapters and status.
Node 1
root@aemhrsDV1 # ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.100.30 netmask ffffff00 broadcast 192.168.100.255
ether 0:3:ba:39:f5:62
ce0:1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.101.30 netmask ffffff00 broadcast 192.168.101.255
ce1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.251.30 netmask ffffff00 broadcast 192.168.251.255
ether 0:3:ba:39:f5:ef
ge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 10.10.3.30 netmask ffffff00 broadcast 10.10.3.255
groupname nafo0
ether 0:3:ba:b:e:8
ge0:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 4
inet 10.10.3.31 netmask ffffff00 broadcast 10.10.3.255
qfe0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 5
inet 10.10.3.33 netmask ffffff00 broadcast 10.10.3.255
groupname nafo0
ether 0:3:ba:17:97:d5
qfe0:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 5
inet 10.10.3.32 netmask ffffff00 broadcast 10.10.3.255
qfe2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 6
inet 192.168.2.112 netmask ffffff00 broadcast 192.168.2.255
ether 0:3:ba:17:97:d7
qfe7: flags=1008843<UP,BROADCAST,RUNNING,MULTICAST,PRIVATE,IPv4> mtu 1500 index 7
inet 172.16.1.1 netmask ffffff80 broadcast 172.16.1.127
ether 0:3:ba:17:98:68
qfe3: flags=1008843<UP,BROADCAST,RUNNING,MULTICAST,PRIVATE,IPv4> mtu 1500 index 8
inet 172.16.0.129 netmask ffffff80 broadcast 172.16.0.255
ether 0:3:ba:17:97:d8
clprivnet0: flags=1009843<UP,BROADCAST,RUNNING,MULTICAST,MULTI_BCAST,PRIVATE,IPv4> mtu 1486 index 9
inet 172.16.193.1 netmask ffffff00 broadcast 172.16.193.255
ether 0:0:0:0:0:1Node 2
root@aemhrsDV2 # ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.100.40 netmask ffffff00 broadcast 192.168.100.255
ether 0:3:ba:39:f5:50
ce0:1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.101.40 netmask ffffff00 broadcast 192.168.101.255
ce1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.251.40 netmask ffffff00 broadcast 192.168.251.255
ether 0:3:ba:39:f5:20
ge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 10.10.3.40 netmask ffffff00 broadcast 10.10.3.255
groupname nafo0
ether 0:3:ba:b:41:22
ge0:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 4
inet 10.10.3.41 netmask ffffff00 broadcast 10.10.3.255
qfe0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 5
inet 10.10.3.43 netmask ffffff00 broadcast 10.10.3.255
groupname nafo0
ether 0:3:ba:17:96:2d
qfe0:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 5
inet 10.10.3.42 netmask ffffff00 broadcast 10.10.3.255
qfe0:2: flags=1040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4> mtu 1500 index 5
inet 10.10.3.35 netmask ffffff00 broadcast 10.10.3.255
qfe7: flags=1008843<UP,BROADCAST,RUNNING,MULTICAST,PRIVATE,IPv4> mtu 1500 index 6
inet 172.16.1.2 netmask ffffff80 broadcast 172.16.1.127
ether 0:3:ba:17:97:18
qfe3: flags=1008843<UP,BROADCAST,RUNNING,MULTICAST,PRIVATE,IPv4> mtu 1500 index 7
inet 172.16.0.130 netmask ffffff80 broadcast 172.16.0.255
ether 0:3:ba:17:96:30
clprivnet0: flags=1009843<UP,BROADCAST,RUNNING,MULTICAST,MULTI_BCAST,PRIVATE,IPv4> mtu 1486 index 8
inet 172.16.193.2 netmask ffffff00 broadcast 172.16.193.255
ether 0:0:0:0:0:2
root@aemhrsDV1 # scstat
-- Cluster Nodes --
Node name Status
Cluster node: aemhrsDV1 Online
Cluster node: aemhrsDV2 Online
-- Cluster Transport Paths --
Endpoint Endpoint Status
Transport path: aemhrsDV1:qfe7 aemhrsDV2:qfe7 Path online
Transport path: aemhrsDV1:qfe3 aemhrsDV2:qfe3 Path online
-- Quorum Summary --
Quorum votes possible: 3
Quorum votes needed: 2
Quorum votes present: 3
-- Quorum Votes by Node --
Node Name Present Possible Status
Node votes: aemhrsDV1 1 1 Online
Node votes: aemhrsDV2 1 1 Online
-- Quorum Votes by Device --
Device Name Present Possible Status
Device votes: /dev/did/rdsk/d3s2 1 1 Online
-- Device Group Servers --
Device Group Primary Secondary
Device group servers: rmt/1 - -
Device group servers: rmt/2 - -
-- Device Group Status --
Device Group Status
Device group status: rmt/1 Offline
Device group status: rmt/2 Offline
-- Multi-owner Device Groups --
Device Group Online Status
-- Resource Groups and Resources --
Group Name Resources
Resources: nfs-test aemhrsDVlh
Resources: hastp-aemhrsDV1-rg -
Resources: hastp-aemhrsDV2-rg -
Resources: rac-framework-rg rac_framework rac_udlm rac_cvm
-- Resource Groups --
Group Name Node Name State
Group: nfs-test aemhrsDV1 Offline
Group: nfs-test aemhrsDV2 Online
Group: hastp-aemhrsDV1-rg aemhrsDV1 Online
Group: hastp-aemhrsDV2-rg aemhrsDV2 Online
Group: rac-framework-rg aemhrsDV1 Pending online
Group: rac-framework-rg aemhrsDV2 Online
-- Resources --
Resource Name Node Name State Status Message
Resource: aemhrsDVlh aemhrsDV1 Offline Offline
Resource: aemhrsDVlh aemhrsDV2 Online Online - LogicalHostname online.
Resource: rac_framework aemhrsDV1 Starting Degraded - reconfiguration in progress
Resource: rac_framework aemhrsDV2 Online Online
Resource: rac_udlm aemhrsDV1 Offline Offline
Resource: rac_udlm aemhrsDV2 Online Online
Resource: rac_cvm aemhrsDV1 Offline Offline
Resource: rac_cvm aemhrsDV2 Online Online
-- IPMP Groups --
Node Name Group Status Adapter Status
--------- ----- ------ ------- ------I believe the reconfig is coming from aemhrsDV2 since sccheck will not run.
Suggestions?
Also the output from the sccheck commad using 'ksh -x' shows where the error is occurring and exiting with a status of 107.
The line executed is 765 of the script.
# echo "CLASSPATH: ${CLASSPATH}"
${JAVA} -classpath ${CLASSPATH} ${JDEFINES_LIST} ${JAVA_CLIENT} &
JVM_PID=$!
+ JVM_PID=13881
# now wait for java to exit
wait $JVM_PID
+ wait 13881
+ /usr/java/bin/java -classpath /usr/cluster/lib/sccheck:/usr/cluster/lib/sccheck/sccheck.jar:/usr/cluster/lib/sccheck/k
ae/kae.jar:/usr/cluster/lib/sccheck/kae/kae-libs.jar:/usr/cluster/lib/sccheck/kae/eras-common.jar:/usr/cluster/lib/scche
ck/kae/common-libs.jar:/usr/cluster/lib/sccheck/kae/eras-parsers.jar:/usr/cluster/lib/sccheck/kae/explorer-input-source.
jar:/usr/cluster/lib/sccheck/kae/resources:/var/cluster/sccheck/tmp/client.0 -Dcom.sun.eras.common.logging4.config.file=
/usr/cluster/lib/sccheck/sccheck.logging4.properties -Dke.client.log=/var/cluster/logs/sccheck/ke-client.log.0 -Dke.clie
nt.xsldir=/var/cluster/sccheck/tmp/client.0 -Dsccheck.clustername=aemhrsDV -Dsccheck.clustermode=true -Dsccheck.localnam
e=aemhrsDV2 -Dsccheck.privatelocalname=clusternode2-priv -Dsccheck.publicnodenames=aemhrsDV1,aemhrsDV2 -Dsccheck.private
nodenames=clusternode1-priv,clusternode2-priv -Dsccheck.clientnumber=0 -Dsccheck.explorersgzDir=/var/cluster/sccheck/exp
lorers-gz -Dsccheck.explorersUnpackDir=/var/cluster/sccheck/explorers.0 -Dsccheck.gunzip=/usr/bin/gunzip -Dsccheck.tar=/
usr/bin/tar -Dsccheck.brief=true -Dsccheck.vverbose=true -Dsccheck.hostlist=aemhrsDV2 -Dsccheck.outputDir=/var/cluster/s
ccheck/reports.2007-08-10.09:19:37 com.sun.cluster.sccheck.SccheckClient
sccheck: Requesting explorer data and node report from aemhrsDV2.
sccheck: aemhrsDV2 error: Connection refused
sccheck: Unable to run checks on: aemhrsDV2
typeset -i exitstatus=$?
+ typeset -i exitstatus=107
# constuct closing message if reports were created
if ((${exitstatus} > 0)) && ((${exitstatus} < 100)); then
typeset severity=""
printf ""
case "${exitstatus}" in
1) severity=$(gettext '1 (LOW)');;
2) severity=$(gettext '2 (MODERATE)');;
3) severity=$(gettext '3 (HIGH)');;
4) severity=$(gettext '4 (CRITICAL)');;
esac
printf "$(gettext '%s: One or more checks failed.')\n" ${PROG}
printf "$(gettext '%s: The greatest severity of all check failures was %s.')\n" ${PROG} "${severity}"
printf "$(gettext '%s: Reports are in %s.')\n" ${PROG} ${OUTPUTDIR}
fi
+ (( 107 > 0 ))
+ (( 107 < 100 ))
cleanup
+ cleanup
exit ${exitstatus}
+ exit 107
Similar Messages
-
Decision Service calls failing with connection refused
Hi All,
Breifing of the bpel process - Async bpel process XX_BPEL_ASYNC_002 calls decision services and a sync bpel process XX_BPEL_SYNC_001.
We have moved to cluster 10.1.3.5.0 from 10.1.3.3.0 and the deployement of the bpel process and the decision service done on two nodes i.e., node51 and node55.
But the bpel process is able to call the decision service only when the node 51 is UP and running, but if node 51 is down and node 55 is up and running it is failing with connection refused error. It is also working when 55 is DOWN and 051 is UP.
the exact error is:
exception on JaxRpc invoke: HTTP transport error: javax.xml.soap.SOAPException: java.security.PrivilegedActionException: javax.xml.soap.SOAPException: Message send failed: Connection refused.
We are using file based repository.
It is failing when it tries to call particular url:
http://loadbalancerurl:7777/orabpel/domain001/XX_BPEL_ASYNC_002/1.0/decisionservices.decs
Can anyone please help me or advice me for finding some solution.
Thanks
SreejitHi Fatsah,
It has been a while since we resolved this problem. But these were the basic steps that we had taken.
The receiver was configured a File adatpter with FTP:
Port: 10021
Connection security : FTPS (FTP using SSL/TLS) for Control and Data Connection
Command Order: AUTH TLS,USER,PASS,PBSZ,PROT
Problem: The message was blocked in our firewall.
FTPS in this case used 10021 as the control port and the firewall allowed to pass the control request.
Once the connection was accepted at the control level, it generated a random port number to pass data on the channel.
This random port number was blocked in the firewall.
We monitored the data port numbers generated at firewall. Then we configured the firewall to open any port number between the specific IP addresses of the sender and the receiver. That resolved the problem.
Hope this helps!
Please give points if this is helpful.
Thank you.
Dharmasiri Amith -
Opmn fails with connection refused
Hi all,
I've successfully installed Oracle Application Server 10g AS R2.
After installation I could successfull login and access both Infra and Middle Tier using OEM, which were configured under a single Farm.
But unfortunately, after and when the server is restarted... opmnctl startall hangs with ons.log contents as below
08/06/23 16:25:14 [4] ONS server initiated
08/06/23 16:53:15 [4] Logging disabled
08/06/23 16:57:43 [4] ONS server initiated
08/06/23 16:57:43 [4] Connection 1,192.168.6.183,6201 connect (Connection refused)
08/06/23 16:59:42 [4] Connection 1,192.168.6.183,6201 connect (Connection refused)
08/06/23 17:01:41 [4] Connection 1,192.168.6.183,6201 connect (Connection refused)
08/06/23 17:03:40 [4] Connection 1,192.168.6.183,6201 connect (Connection refused)08/06/23 17:04:00 [4] Logging disabled
As a workaround I verified /etc/hosts file... it is as below
127.0.0.1 localhost.localdomain localhost
192.168.6.183 oravis.dsrc2.com oravis
I'm performing the start-up & shutdown in the following order
START DB Tier
Start Database as
Make sure your are in DB Home
$ sqlplus "/as sysdba"
SQL> startup
Start DB Listener as
Make sure your are in DB Home
$ lsnrctl start RETEK
Startup 10gAS Server
Start Middle Tier iAS Console
Make sure your are in Middle Tier Home
cd $ORACLE_HOME/bin
emctl start iasconsole
Start Infra iAS Console
Make sure your are in Infra Home
cd $ORACLE_HOME/bin
emctl start iasconsole
Start Infra listener as
$ lsnrctl start
Start Infra Database as -
$sqlplus "/as sysdba"
SQL> startup
Start Infra OC4J Services as
Make sure your are in Infra Home
$./opmnctl startall
Start Middle Tier OC4J Services as
Make sure your are in Middle Tier Home
$./opmnctl startall
Shutdown 10gAS Server
Stop Middle Tier Services as
Make sure your are in Middle Tier Home
cd $ORACLE_HOME/opmn/bin
$./opmnctl stopall
Stop Infrastructure Services as
Make sure your are in Infra Home
$ ./opmnctl stopall
Stop Infra Listener as
Make sure your are in Infra Home
$ lsnrctl stop [listener_name]
Stop Infra Database as
Make sure your are in Infra Home
$ sqlplus "/as sysdba"
SQL> shutdown immediate
Stop Infra iAS Console
Make sure your are in Infra Home
cd $ORACLE_HOME/bin
emctl stop iasconsole
Stop Middle Tier iAS Console
Make sure your are in Middle Tier Home
cd $ORACLE_HOME/bin
emctl stop iasconsole
Stop DB Tier
Stop Listener as
Make sure your are in DB Home
$ lsnrctl stop [listener_name]
Stop Database as
Make sure your are in DB Home
$ sqlplus "/as sysdba"
SQL> shutdown immediate
Now... I'm able to access the Infra & Middle tier throgh OEM but the status is Unavailable. Moreover now they not under the Farm (Which they were earlier in).
Also it is giving error connecting to repository database.
Please anybody, who have come across this kind of problem, kindly guide me, where actually I'm missing.
-MaheshHi Adith,
Thanx a lot for the updates and correcting me. I've gone through the documents and corrected the way by which I was starting the services.
But... when I try to do opmnctl startall, now I again got struck up with this strange error in ons.log
08/06/24 10:26:02 [4] ONS server initiated
08/06/24 10:47:51 [2] Connection 1,192.168.6.183,1521 SSL handshake failed
08/06/24 10:47:51 [2] Handshake for 1,192.168.6.183,1521: nz error = 28864 interval = 0 (180 max)
08/06/24 10:49:50 [2] Connection 1,192.168.6.183,1521 SSL handshake failed
08/06/24 10:49:50 [2] Handshake for 1,192.168.6.183,1521: nz error = 28864 interval = 0 (180 max)
08/06/24 10:51:49 [2] Connection 1,192.168.6.183,1521 SSL handshake failed
08/06/24 10:51:49 [2] Handshake for 1,192.168.6.183,1521: nz error = 28864 interval = 0 (180 max)
I've gone through metalink and found out that this is a problem with SSL Authentication which been stated as a bug.
Can anybody answer my following queries...
1. Is it mandatory to enable SSL in 10g AS? Can we run server without SSL?
2. If not mandatory, then how to disable SSL?
3. If the handshake error is a bug, how to fix? Do I need to apply any patch for this?
Looking forward for immediate response,
Regards
-Mahesh -
Calling a WebServices From Java Stored Proc fails with Connection refused
I have followed the example in Note:220662.1 on Metalink step by step.
I am using two windows machines (2000 SP4). I have Oracle 9.2.0.5 EE on one of them and OC4J 9.0.4 standalone on the other(running on JVM 1.4.2_05-b04). The 2 servers "see" each other over the network.
I can execute the stub from the database machine:
C:\WebServices\HelloWorld>java HelloWorldImplWSStub
Hello World - The current time is Sat Aug 21 11:56:20 EDT 2004When running it from the database, I get:
SQL> select ws_hello_world from dual;
select ws_hello_world from dual
ERROR at line 1:
ORA-29532: Java call terminated by uncaught Java exception: [SOAPException:
faultCode=SOAP-ENV:IOException; msg=Connection refused;
targetException=java.net.ConnectException: Connection refused]
Elapsed: 00:00:21.02The trace file generated on the database server machine looks like:
[SOAPException: faultCode=SOAP-ENV:IOException; msg=Connection refused; targetException=java.net.ConnectException: Connection refused]
at oracle.soap.transport.http.OracleSOAPHTTPConnection.send(OracleSOAPHTTPConnection.java:765)
at org.apache.soap.rpc.Call.invoke(Call.java:261)
at HelloWorldImplWSStub.sayHelloWorld(HelloWorldImplWSStub.java:52)Here is the stub code generated using JDeveloper 9.0.5.1:
import oracle.soap.transport.http.OracleSOAPHTTPConnection;
import org.apache.soap.encoding.SOAPMappingRegistry;
import java.net.URL;
import org.apache.soap.rpc.Call;
import org.apache.soap.Constants;
import java.util.Vector;
import org.apache.soap.rpc.Response;
import org.apache.soap.rpc.Parameter;
import org.apache.soap.Fault;
import org.apache.soap.SOAPException;
import java.util.Properties;
public class HelloWorldImplWSStub {
public HelloWorldImplWSStub() {
m_httpConnection = new OracleSOAPHTTPConnection();
m_smr = new SOAPMappingRegistry();
public static String endpoint = "http://oc4jsrv:8888/MyWorkarea-OC4J-context-root/HelloWorldImplWS";
public String getEndpoint() {
return _endpoint;
public void setEndpoint(String endpoint) {
_endpoint = endpoint;
private static OracleSOAPHTTPConnection m_httpConnection = null;
private static SOAPMappingRegistry m_smr = null;
public static String sayHelloWorld() throws Exception {
String returnVal = null;
URL endpointURL = new URL(_endpoint);
Call call = new Call();
call.setSOAPTransport(m_httpConnection);
call.setTargetObjectURI("HelloWorldImplWS");
call.setMethodName("sayHelloWorld");
call.setEncodingStyleURI(Constants.NS_URI_SOAP_ENC);
Vector params = new Vector();
call.setParams(params);
call.setSOAPMappingRegistry(m_smr);
Response response = call.invoke(endpointURL, "");
if (!response.generatedFault()) {
Parameter result = response.getReturnValue();
returnVal = (String)result.getValue();
else {
Fault fault = response.getFault();
throw new SOAPException(fault.getFaultCode(), fault.getFaultString());
return returnVal;
public void setMaintainSession(boolean maintainSession) {
m_httpConnection.setMaintainSession(maintainSession);
public boolean getMaintainSession() {
return m_httpConnection.getMaintainSession();
public void setTransportProperties(Properties props) {
m_httpConnection.setProperties(props);
public Properties getTransportProperties() {
return m_httpConnection.getProperties();
public static void main(String[] argv) throws Exception {
HelloWorldImplWSStub hstub = new HelloWorldImplWSStub();
System.out.println(hstub.sayHelloWorld());
}The PL/SQL function code:
CREATE OR REPLACE FUNCTION ws_hello_world RETURN VARCHAR2
AS LANGUAGE JAVA
NAME 'HelloWorldImplWSStub.sayHelloWorld() return java.lang.String';Any help would be greatly appreciated.Hello,I have the same problem. Did you find any solution to it?
Thanks. Diego (Argentina) -
SMD agent not starting correctly FAIL: NIECONN_REFUSED (Connection refused)
I am getting the following message when I start the agent. I don't see any errors except for this, and when I try to connect it in agent_adminstration, it never connects. Just eventually times out after 30 mins.
FAIL: NIECONN_REFUSED (Connection refused), NiRawConnect failed in plugin_fopen()
cat jvm_SMDAgent.out
LoadBalanceRestricted=no
P4ClassLoad=P4Connection
SAPDBHOST=
SAPINFO=SMD_98_server
SAPMYNAME=ssmsap_SMD_98
SAPSTARTUP=1
SAPSYSTEM=98
SAPSYSTEMNAME=SMD
application.home=/usr/sap/SMD/exe
com.ibm.cpu.endian=little
com.ibm.oti.configuration=scar
com.ibm.oti.jcl.build=20080922_1143
com.ibm.oti.vm.bootstrap.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin
com.ibm.oti.vm.library.version=23
com.ibm.util.extralibs.properties=
com.ibm.vm.bitmode=64
file.encoding=UTF-8
file.separator=/
ibm.signalhandling.rs=false
ibm.signalhandling.sigchain=true
ibm.signalhandling.sigint=true
ibm.system.encoding=UTF-8
j2ee.dbhost=
java.assistive=ON
java.awt.fonts=
java.awt.graphicsenv=sun.awt.X11GraphicsEnvironment
java.awt.printerjob=sun.print.PSPrinterJob
java.class.path=/usr/sap/SMD/J98/../exe/jstartup.jar:/usr/sap/SMD/J98/../exe/jvmx.jar:../../exe/jstartupapi.jar:../../exe/jstartupimpl.jar:lib/patch_7.01.3.0.20090224123938/launcher/smdagentlauncher.jar
java.class.version=48.0
java.compiler=j9jit23
java.ext.dirs=/opt/IBMJava2-amd64-142/jre/lib/ext
java.fullversion=J2RE 1.4.2 IBM J9 2.3 Linux amd64-64 j9vmxa64142-20080923 (JIT enabled)
J9VM - 20080922_23329_LHdSMr
JIT - 20080815_1845_r8
GC - 200809_04
java.home=/opt/IBMJava2-amd64-142/jre
java.io.tmpdir=/tmp
java.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin:/opt/IBMJava2-amd64-142/jre/bin:/opt/IBMJava2-amd64-142/jre/bin/classic:/opt/IBMJava2-amd64-142/jre/bin:/usr/sap/SMD/exe:/usr/lib:/usr/sap/SMD/exe:/usr/sap/SMD/exe
java.runtime.name=Java(TM) 2 Runtime Environment, Standard Edition
java.runtime.version=2.3
java.specification.name=Java Platform API Specification
java.specification.vendor=Sun Microsystems Inc.
java.specification.version=1.4
java.util.prefs.PreferencesFactory=java.util.prefs.FileSystemPreferencesFactory
java.vendor=IBM Corporation
java.vendor.url=http://www.ibm.com/
java.version=1.4.2
java.vm.info=J2RE 1.4.2 IBM J9 2.3 Linux amd64-64 j9vmxa64142-20080923 (JIT enabled)
J9VM - 20080922_23329_LHdSMr
JIT - 20080815_1845_r8
GC - 200809_04
java.vm.name=IBM J9 VM
java.vm.specification.name=Java Virtual Machine Specification
java.vm.specification.vendor=Sun Microsystems Inc.
java.vm.specification.version=1.0
java.vm.vendor=IBM Corporation
java.vm.version=2.3
jstartup.debuggable=yes
jstartup.mode=JCONTROL
jstartup.ownHardwareId=F2143454721
jstartup.ownProcessId=17393
jstartup.whoami=server
jxe.current.romimage.version=9
jxe.lowest.romimage.version=9
line.separator=
memory.manager=256M
os.arch=amd64
os.name=Linux
os.version=2.6.9-89.ELsmp
path.separator=:
sun.boot.class.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm/jclSC14/classes.zip:/opt/IBMJava2-amd64-142/jre/lib/core.jar:/opt/IBMJava2-amd64-142/jre/lib/charsets.jar:/opt/IBMJava2-amd64-142/jre/lib/graphics.jar:/opt/IBMJava2-amd64-142/jre/lib/security.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmpkcs.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmorb.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmorbapi.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjcefw.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjssefips.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjgssprovider.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjsseprovider.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjaaslm.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmcertpathprovider.jar:/opt/IBMJava2-amd64-142/jre/lib/server.jar:/opt/IBMJava2-amd64-142/jre/lib/xml.jar
sun.boot.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin
sun.io.unicode.encoding=UnicodeLittle
sun.java2d.fontpath=
sys.global.dir=/usr/sap/SMD/SYS/global
user.country=US
user.dir=/usr/sap/SMD/J98/SMDAgent
user.home=/home/smdadm
user.language=en
user.name=smdadm
user.timezone=
user.variant=
Running SMD Agent ...
[p4://ssmsap:50004] Agent ready.
Initialization done.
cat jvm_SMDAgent.out
LoadBalanceRestricted=no
P4ClassLoad=P4Connection
SAPDBHOST=
SAPINFO=SMD_98_server
SAPMYNAME=ssmsap_SMD_98
SAPSTARTUP=1
SAPSYSTEM=98
SAPSYSTEMNAME=SMD
application.home=/usr/sap/SMD/exe
com.ibm.cpu.endian=little
com.ibm.oti.configuration=scar
com.ibm.oti.jcl.build=20080922_1143
com.ibm.oti.vm.bootstrap.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin
com.ibm.oti.vm.library.version=23
com.ibm.util.extralibs.properties=
com.ibm.vm.bitmode=64
file.encoding=UTF-8
file.separator=/
ibm.signalhandling.rs=false
ibm.signalhandling.sigchain=true
ibm.signalhandling.sigint=true
ibm.system.encoding=UTF-8
j2ee.dbhost=
java.assistive=ON
java.awt.fonts=
java.awt.graphicsenv=sun.awt.X11GraphicsEnvironment
java.awt.printerjob=sun.print.PSPrinterJob
java.class.path=/usr/sap/SMD/J98/../exe/jstartup.jar:/usr/sap/SMD/J98/../exe/jvmx.jar:../../exe/jstartupapi.jar:../../exe/jstartupimpl.jar:lib/patch_7.01.3.0.20090224123938/launcher/smdagentlauncher.jar
java.class.version=48.0
java.compiler=j9jit23
java.ext.dirs=/opt/IBMJava2-amd64-142/jre/lib/ext
java.fullversion=J2RE 1.4.2 IBM J9 2.3 Linux amd64-64 j9vmxa64142-20080923 (JIT enabled)
J9VM - 20080922_23329_LHdSMr
JIT - 20080815_1845_r8
GC - 200809_04
java.home=/opt/IBMJava2-amd64-142/jre
java.io.tmpdir=/tmp
java.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin:/opt/IBMJava2-amd64-142/jre/bin:/opt/IBMJava2-amd64-142/jre/bin/classic:/opt/IBMJava2-amd64-142/jre/bin:/usr/sap/SMD/exe:/usr/lib:/usr/sap/SMD/exe:/usr/sap/SMD/exe
java.runtime.name=Java(TM) 2 Runtime Environment, Standard Edition
java.runtime.version=2.3
java.specification.name=Java Platform API Specification
java.specification.vendor=Sun Microsystems Inc.
java.specification.version=1.4
java.util.prefs.PreferencesFactory=java.util.prefs.FileSystemPreferencesFactory
java.vendor=IBM Corporation
java.vendor.url=http://www.ibm.com/
java.version=1.4.2
java.vm.info=J2RE 1.4.2 IBM J9 2.3 Linux amd64-64 j9vmxa64142-20080923 (JIT enabled)
J9VM - 20080922_23329_LHdSMr
JIT - 20080815_1845_r8
GC - 200809_04
java.vm.name=IBM J9 VM
java.vm.specification.name=Java Virtual Machine Specification
java.vm.specification.vendor=Sun Microsystems Inc.
java.vm.specification.version=1.0
java.vm.vendor=IBM Corporation
java.vm.version=2.3
jstartup.debuggable=yes
jstartup.mode=JCONTROL
jstartup.ownHardwareId=F2143454721
jstartup.ownProcessId=17393
jstartup.whoami=server
jxe.current.romimage.version=9
jxe.lowest.romimage.version=9
line.separator=
memory.manager=256M
os.arch=amd64
os.name=Linux
os.version=2.6.9-89.ELsmp
path.separator=:
sun.boot.class.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm/jclSC14/classes.zip:/opt/IBMJava2-amd64-142/jre/lib/core.jar:/opt/IBMJava2-amd64-142/jre/lib/charsets.jar:/opt/IBMJava2-amd64-142/jre/lib/graphics.jar:/opt/IBMJava2-amd64-142/jre/lib/security.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmpkcs.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmorb.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmorbapi.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjcefw.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjssefips.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjgssprovider.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjsseprovider.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmjaaslm.jar:/opt/IBMJava2-amd64-142/jre/lib/ibmcertpathprovider.jar:/opt/IBMJava2-amd64-142/jre/lib/server.jar:/opt/IBMJava2-amd64-142/jre/lib/xml.jar
sun.boot.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin
sun.io.unicode.encoding=UnicodeLittle
sun.java2d.fontpath=
sys.global.dir=/usr/sap/SMD/SYS/global
user.country=US
user.dir=/usr/sap/SMD/J98/SMDAgent
user.home=/home/smdadm
user.language=en
user.name=smdadm
user.timezone=
user.variant=
Running SMD Agent ...
[p4://ssmsap:50004] Agent ready.
Initialization done.cat dev_SMDAgent
trc file: "/usr/sap/SMD/J98/work/dev_SMDAgent", trc level: 1, release: "701"
node name : smdagent
pid : 17393
system name : SMD
system nr. : 98
started at : Wed Oct 7 08:56:32 2009
arguments :
arg[00] : /usr/sap/SMD/J98/../exe/jlaunch
arg[01] : pf=/usr/sap/SMD/J98/../SYS/profile/SMD_J98_ssmsap
arg[02] : -DSAPINFO=SMD_98_server
arg[03] : pf=/usr/sap/SMD/J98/../SYS/profile/SMD_J98_ssmsap
JStartupReadInstanceProperties: read instance properties [/usr/sap/SMD/J98/profile/smd.properties]
-> ms host :
-> ms port : 36
-> OS libs : /usr/sap/SMD/exe
-> Admin URL :
-> run mode : NORMAL
-> run action : NONE
-> enabled : yes
Used property files
-> files [00] : /usr/sap/SMD/J98/profile/smd.properties
Instance properties
-> ms host :
-> ms port : 36
-> os libs : /usr/sap/SMD/exe
-> admin URL :
-> run mode : NORMAL
-> run action : NONE
-> enabled : yes
Bootstrap nodes
Worker nodes
-> [00] smdagent : /usr/sap/SMD/J98/profile/smd.properties
[Thr 182894174624] Wed Oct 7 08:56:32 2009
[Thr 182894174624] JLaunchRequestQueueInit: create named pipe for ipc
[Thr 182894174624] JLaunchRequestQueueInit: create pipe listener thread
[Thr 1074792800] JLaunchRequestFunc: Thread 1074792800 started as listener thread for np messages.
[Thr 1085282656] WaitSyncSemThread: Thread 1085282656 started as semaphore monitor thread.
[Thr 182894174624] SigISetDefaultAction : default handling for signal 17
[Thr 182894174624] NiInit3: NI already initialized; param 'maxHandles' ignored (1;202)
[Thr 182894174624] CPIC (version=701.2009.01.26)
[Thr 182894174624] [Node: SMDAgent] java home is set by profile parameter
Java Home: /opt/IBMJava2-amd64-142
[Thr 182894174624] JStartupICheckFrameworkPackage: can't find framework package /usr/sap/SMD/J98/../exe/jvmx.jar
JStartupIReadSection: read node properties [smdagent]
-> node name : SMDAgent
-> node type : server
-> node id : 1
-> node execute : yes
-> java path : /opt/IBMJava2-amd64-142
-> java parameters : -DP4ClassLoad=P4Connection -Xj9 -Xmn50m -Xgcpolicy:gencon
-> java vm version : J2RE 1.4.2 IBM J9 2.3 Linux amd64-64 j9vmxa64142-20080923 (JIT enabled)
-> java vm vendor : IBM J9 VM (IBM Corporation)
-> java vm type : server
-> java vm cpu : amd64
-> heap size : 256M
-> init heap size : 256M
-> root path : ../SMDAgent
-> class path : ../../exe/jstartupapi.jar:../../exe/jstartupimpl.jar:lib/patch_7.01.3.0.20090224123938/launcher/smdagentlauncher.jar
-> OS libs path : /usr/sap/SMD/exe
-> main class : com.sap.smd.agent.launcher.SMDAgentLauncher
-> framework class : com.sap.bc.proj.jstartup.JStartupFramework
-> registr. class : com.sap.bc.proj.jstartup.JStartupNatives
-> framework path : /usr/sap/SMD/J98/../exe/jstartup.jar:/usr/sap/SMD/J98/../exe/jvmx.jar
-> parameters : run jcontrol
-> debuggable : yes
-> debug mode : no
-> debug port : 58981
-> shutdown timeout : 20000
[Thr 182894174624] JLaunchISetDebugMode: set debug mode [no]
[Thr 1086335328] JLaunchIStartFunc: Thread 1086335328 started as Java VM thread.
JHVM_LoadJavaVM: VM Arguments of node [SMDAgent]
-> stack : 1048576 Bytes
-> arg[ 0]: exit
-> arg[ 1]: abort
-> arg[ 2]: vfprintf
-> arg[ 3]: -DP4ClassLoad=P4Connection
-> arg[ 4]: -Xj9
-> arg[ 5]: -Xmn50m
-> arg[ 6]: -Xgcpolicy:gencon
-> arg[ 7]: -Dsys.global.dir=/usr/sap/SMD/SYS/global
-> arg[ 8]: -Dapplication.home=/usr/sap/SMD/exe
-> arg[ 9]: -Djava.class.path=/usr/sap/SMD/J98/../exe/jstartup.jar:/usr/sap/SMD/J98/../exe/jvmx.jar:../../exe/jstartupapi.jar:../../exe/jstartupimpl.jar:lib/patch_7.01.3.0.20090224123938/launcher/smdagentlauncher.jar
-> arg[ 10]: -Djava.library.path=/opt/IBMJava2-amd64-142/jre/bin/j9vm:/opt/IBMJava2-amd64-142/jre/bin:/opt/IBMJava2-amd64-142/jre/bin:/opt/IBMJava2-amd64-142/jre/bin/classic:/opt/IBMJava2-amd64-142/jre/bin:/usr/sap/SMD/exe:/usr/lib:/usr/sap/SMD/exe:/usr/sap/SMD/exe
-> arg[ 11]: -Dmemory.manager=256M
-> arg[ 12]: -Xmx256M
-> arg[ 13]: -Xms256M
-> arg[ 14]: -DLoadBalanceRestricted=no
-> arg[ 15]: -Djstartup.mode=JCONTROL
-> arg[ 16]: -Djstartup.ownProcessId=17393
-> arg[ 17]: -Djstartup.ownHardwareId=F2143454721
-> arg[ 18]: -Djstartup.whoami=server
-> arg[ 19]: -Djstartup.debuggable=yes
-> arg[ 20]: -DSAPINFO=SMD_98_server
-> arg[ 21]: -DSAPSTARTUP=1
-> arg[ 22]: -DSAPSYSTEM=98
-> arg[ 23]: -DSAPSYSTEMNAME=SMD
-> arg[ 24]: -DSAPMYNAME=ssmsap_SMD_98
-> arg[ 25]: -DSAPDBHOST=
-> arg[ 26]: -Dj2ee.dbhost=
[Thr 1086335328] JHVM_LoadJavaVM: Java VM created OK.
JHVM_BuildArgumentList: main method arguments of node [SMDAgent]
-> arg[ 0]: run
-> arg[ 1]: jcontrol
[Thr 1086335328] JHVM_RegisterNatives: registering methods in com.sap.bc.proj.jstartup.JStartupFramework
[Thr 1086335328] Wed Oct 7 08:56:35 2009
[Thr 1086335328] JLaunchISetState: change state from [Initial (0)] to [Initial (0)]
[Thr 1086335328] JLaunchISetState: change state from [Initial (0)] to [Waiting for start (1)]
[Thr 1086335328] Wed Oct 7 08:56:38 2009
[Thr 1086335328] JLaunchISetState: change state from [Waiting for start (1)] to [Starting (2)]
[Thr 1086335328] JLaunchISetState: change state from [Starting (2)] to [Running (3)]
[Thr 1101334880] Wed Oct 7 08:56:43 2009
[Thr 1101334880] JLaunchISetState: change state from [Running (3)] to [Starting applications (10)]
[Thr 1101334880] Wed Oct 7 08:56:48 2009
[Thr 1101334880] JLaunchISetState: change state from [Starting applications (10)] to [Running (3)] -
BIPCatalogUtil extraction always fails with "Connection timed out"
BIPCatalogUtil extraction always fails with "Connection timed out".
Any suggestions on what could be the issue?One thought was that perhaps it was timing out going out some unused port (e.g., the Airport port), but a list shows only the Ethernet port is enabled:
admin$ sudo networksetup -listallnetworkservices
An asterisk (*) denotes that a network service is disabled.
Built-in Ethernet
*AirPort
*Built-in FireWire
*Bluetooth -
Connect to message server host failed;WSAECONNREFUSED: Connection refused
Hi All,
I am getting the following error when I tried to test the system connectivity from the portal to NSP instance.
Connection failed. Make sure that Single Sign-On is configured correctly
I found the following entry in the logs
Error> occured >Wed Feb 03 22:43:49,875<
RfcException:
message: Connect to message server host failed
Connect_PM TYPE=B MSHOST=abchome.abcsap.local GROUP=SPACE R3NAME=NSP MSSERV=sapmsNSP PCS=1
ERROR partner '192.xxx.xxx.123:sapmsNSP' not reached
TIME Wed Feb 03 22:43:49 2010
RELEASE 700
COMPONENT NI (network interface)
VERSION 38
RC -10
MODULE nixxi.cpp
LINE 2823
DETAIL NiPConnect2
SYSTEM CALL connect
ERRNO 10061
ERRNO TEXT WSAECONNREFUSED: Connection refused
COUNTER 1
Return code: RFC_FAILURE(1)
error group: 102
key: RFC_ERROR_COMMUNICATION
Both NSP and J2E instances are on the same server. OS - win2k3.
I checked the services file and have the sapmsNSP entry.
I am able to launch an SAP transaction from System Administration -> Support
RZ70 from NSP also fails JCo error. SLD_UC RFC itself works fine and the JCo RFC provider SLD_UC program is running
WEB AS & ITS connections work fine.
User authentication is from backend, NSP.
I think I have gone thru all the logs but could not resolve the issue.
I appreciate any help on this,
VictorI tried to go thru the thread. I did not find any clue as why only server connectivity is failing. ABAP trial version is running fine and the NW trial version is working fine too. These run without crashing. I did a lot of customizing on the portal but dont see any issues except the System Connectivity. Like I mentioned I did UME configuration to point to NSP ABAP instance and I can log into the portal with user credentials that I use to login to ABAP. I can launch webgui etc without any issues.
-
Netbean Oracle : Problem with connection refused
Hi, Im currently using Netbean to develop a system in JSP. I already succeed to connect to Oracle 11g. However, I'm facing problem connection refused. It always happen.
For the server, I using GlassFish Server 3.1
Any one have idea to solve this problem? Thanks in advances.
Detail of the error:
WARNING: StandardWrapperValve[jsp]: PWC1406: Servlet.service() for servlet jsp threw exception
java.sql.SQLException: Io exception: Connection refused(DESCRIPTION=(TMP=)(VSNNUM=186646784)(ERR=12519)(ERROR_STACK=(ERROR=(CODE=12519)(EMFI=4))))
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:134)
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:179)
at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:333)
at oracle.jdbc.driver.OracleConnection.<init>(OracleConnection.java:404)
at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.java:468)
at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:314)
at java.sql.DriverManager.getConnection(DriverManager.java:579)
at java.sql.DriverManager.getConnection(DriverManager.java:221)
at dbConnection.dbConnection.connectEasy(dbConnection.java:66)
at org.apache.jsp.Boundary.insertStudForm_jsp._jspService(insertStudForm_jsp.java:783)
at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:111)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:847)
at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:403)
at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:492)
at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:378)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:847)
at org.apache.catalina.core.StandardWrapper.service(StandardWrapper.java:1539)
at org.apache.catalina.core.ApplicationDispatcher.doInvoke(ApplicationDispatcher.java:787)
at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDispatcher.java:649)
at org.apache.catalina.core.ApplicationDispatcher.doInclude(ApplicationDispatcher.java:604)
at org.apache.catalina.core.ApplicationDispatcher.include(ApplicationDispatcher.java:534)
at org.apache.jasper.runtime.JspRuntimeLibrary.include(JspRuntimeLibrary.java:1015)
at org.apache.jsp.index_jsp._jspService(index_jsp.java:462)
at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:111)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:847)
at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:403)
at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:492)
at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:378)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:847)
at org.apache.catalina.core.StandardWrapper.service(StandardWrapper.java:1539)
at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:281)
at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:175)
at org.apache.catalina.core.StandardPipeline.doInvoke(StandardPipeline.java:655)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:595)
at com.sun.enterprise.web.WebPipeline.invoke(WebPipeline.java:98)
at com.sun.enterprise.web.PESessionLockingStandardPipeline.invoke(PESessionLockingStandardPipeline.java:91)
at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:162)
at org.apache.catalina.connector.CoyoteAdapter.doService(CoyoteAdapter.java:330)
at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:231)
at com.sun.enterprise.v3.services.impl.ContainerMapper.service(ContainerMapper.java:174)
at com.sun.grizzly.http.ProcessorTask.invokeAdapter(ProcessorTask.java:828)
at com.sun.grizzly.http.ProcessorTask.doProcess(ProcessorTask.java:725)
at com.sun.grizzly.http.ProcessorTask.process(ProcessorTask.java:1019)
at com.sun.grizzly.http.DefaultProtocolFilter.execute(DefaultProtocolFilter.java:225)
at com.sun.grizzly.DefaultProtocolChain.executeProtocolFilter(DefaultProtocolChain.java:137)
at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:104)
at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:90)
at com.sun.grizzly.http.HttpProtocolChain.execute(HttpProtocolChain.java:79)
at com.sun.grizzly.ProtocolChainContextTask.doCall(ProtocolChainContextTask.java:54)
at com.sun.grizzly.SelectionKeyContextTask.call(SelectionKeyContextTask.java:59)
at com.sun.grizzly.ContextTask.run(ContextTask.java:71)
at com.sun.grizzly.util.AbstractThreadPool$Worker.doWork(AbstractThreadPool.java:532)
at com.sun.grizzly.util.AbstractThreadPool$Worker.run(AbstractThreadPool.java:513)
at java.lang.Thread.run(Thread.java:722)user8963384 wrote:
I already run the sql that you ask, this is the result
RESOURCE_NAME CURRENT_UTILIZATION MAX_UTILIZATION INITIAL_ALLOCATION LIMIT_VALUE
processes 26 150 150 150
sessions 30 154 248 248
This my function I use to connect to database
public class dbConnection {
public Connection conn=null;
public String id="Se";
public String password="See";
public dbConnection(){
public dbConnection (String id, String password){
this.id=id;
this.password=password;
public void connect(){
try{
//load driver
String driverName="oracle.jdbc.driver.OracleDriver";
Class.forName(driverName);
//Create connection
String serverName = "localhost";
Is it the same server on which db is running. Better put servername or IP for serverName above.
String portNumber = "1521";
String sid = "DEGREE";
String url = "jdbc:oracle:thin:@" + serverName + ":" + portNumber + ":" + sid;
System.out.println("url: " + url);
conn = DriverManager.getConnection(url,id,password);
}Can you try id/password@(DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))) (CONNECT_DATA = (SERVICE_NAME = DEGREE))) from sql prompt and post the result.
catch(ClassNotFoundException e){
System.out.println("ClassNotFoundException: " + e.getMessage());
catch(SQLException e){
System.out.println("SQLException: " + e.getMessage());
while((e = e.getNextException()) != null)
System.out.println(e.getMessage());
}Everything goes OK, then download latest driver from oracle corporation and try again. A code sample can be found at http://www.orafaq.com/wiki/JDBC.
Regards
Virendra
Edited by: Virendra.k.Yadav on Oct 18, 2011 11:26 PM -
Restore default isolation level fails with connection in pool
Hi,
I am developing an application that needs to set the TransactionIsolation to SERIALIZE for a transaction. Setting the TransactionIsolation is not the problem. After this transaction is committed or rolled back, i set the isolation level back to the default i saved before.
The code gets executed and throws no exception. The connection i used is released into the pool. The next time i get this connection from the pool the isolation level is already SERIALIZE. This is not what i wanted to achieve.
It has to be possible to change the isolation level for transaction, isn´t it?
Here is the code, that i use. The ConnectionManager gets the connection from a connection pool i configured in the jdbc connector service. Excep for this issue any other operation works fine.
ConnectionManager connectionManager = new ConnectionManager();
Connection con = null;
int transactionIsolationLevel = 0;
Queue queue = null;
List list = null;
try {
con = connectionManager.getConnection();
transactionIsolationLevel = con.getTransactionIsolation();
if( logger.isInfoEnabled())
logger.info(LOGLOC + "ISOLATION_LEVEL default: " + transactionIsolationLevel);
// auskommentiert für RE
con.setTransactionIsolation( Connection.TRANSACTION_SERIALIZABLE );
con.setAutoCommit( false );
QueueManager queueManager = new QueueManager();
list = queueManager.GetQueueEntriesBySizeGroups( con, small, medium, large, serverNode );
con.commit();
} catch (ClassNotFoundException cnfe) {
logger.error(LOGLOC + "Exception setting up transaction context for queue service!", cnfe);
handleExceptions(queue, cnfe);
try {
con.rollback();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception rolling back transaction!", e);
} catch (SQLException sqle) {
logger.error(LOGLOC + "Exception setting up transaction context for queue service!", sqle);
handleExceptions(queue, sqle);
try {
con.rollback();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception rolling back transaction!", e);
} catch (QueueManagerException qme) {
logger.error(LOGLOC + "Exception executing queue manager!", qme);
handleExceptions(queue, qme);
try {
con.rollback();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception rolling back transaction!", e);
} finally {
try {
con.setAutoCommit(true);
if( logger.isInfoEnabled())
logger.info(LOGLOC + "ISOLATION_LEVEL before setting default: " + con.getTransactionIsolation() + " now setting: " + transactionIsolationLevel );
// Auskommentiert für RE
con.setTransactionIsolation( transactionIsolationLevel );
con.close();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception setting up transaction context for queue service!", e);
The datasource is a simple jdbc1.x Oracle Datasource with no special settings.
In a remote debugging session i saw, that the wrapped Connection from the datasource sets the txLevel successfully, But the underlying T4Connection does not get this isolation level. Could this be a bug?
Any hints, solutions?Hi,
I am developing an application that needs to set the TransactionIsolation to SERIALIZE for a transaction. Setting the TransactionIsolation is not the problem. After this transaction is committed or rolled back, i set the isolation level back to the default i saved before.
The code gets executed and throws no exception. The connection i used is released into the pool. The next time i get this connection from the pool the isolation level is already SERIALIZE. This is not what i wanted to achieve.
It has to be possible to change the isolation level for transaction, isn´t it?
Here is the code, that i use. The ConnectionManager gets the connection from a connection pool i configured in the jdbc connector service. Excep for this issue any other operation works fine.
ConnectionManager connectionManager = new ConnectionManager();
Connection con = null;
int transactionIsolationLevel = 0;
Queue queue = null;
List list = null;
try {
con = connectionManager.getConnection();
transactionIsolationLevel = con.getTransactionIsolation();
if( logger.isInfoEnabled())
logger.info(LOGLOC + "ISOLATION_LEVEL default: " + transactionIsolationLevel);
// auskommentiert für RE
con.setTransactionIsolation( Connection.TRANSACTION_SERIALIZABLE );
con.setAutoCommit( false );
QueueManager queueManager = new QueueManager();
list = queueManager.GetQueueEntriesBySizeGroups( con, small, medium, large, serverNode );
con.commit();
} catch (ClassNotFoundException cnfe) {
logger.error(LOGLOC + "Exception setting up transaction context for queue service!", cnfe);
handleExceptions(queue, cnfe);
try {
con.rollback();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception rolling back transaction!", e);
} catch (SQLException sqle) {
logger.error(LOGLOC + "Exception setting up transaction context for queue service!", sqle);
handleExceptions(queue, sqle);
try {
con.rollback();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception rolling back transaction!", e);
} catch (QueueManagerException qme) {
logger.error(LOGLOC + "Exception executing queue manager!", qme);
handleExceptions(queue, qme);
try {
con.rollback();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception rolling back transaction!", e);
} finally {
try {
con.setAutoCommit(true);
if( logger.isInfoEnabled())
logger.info(LOGLOC + "ISOLATION_LEVEL before setting default: " + con.getTransactionIsolation() + " now setting: " + transactionIsolationLevel );
// Auskommentiert für RE
con.setTransactionIsolation( transactionIsolationLevel );
con.close();
} catch (SQLException e) {
logger.error(LOGLOC + "Exception setting up transaction context for queue service!", e);
The datasource is a simple jdbc1.x Oracle Datasource with no special settings.
In a remote debugging session i saw, that the wrapped Connection from the datasource sets the txLevel successfully, But the underlying T4Connection does not get this isolation level. Could this be a bug?
Any hints, solutions? -
For almost a week now I have suffered this error.
The package is rather large (12MB) yet, I successfully uploaded larger files to youtube yesterday so, it can't be my internet connection.
Any solutions ?
Can we upload packages another way ? through dropbox for example and then import it ?Hey Mostafa,
Thank you for the question. The only was to submit an app for certification is through your developer dashboard, so the dropbox idea is not feasible. I believe this could stem from your internet provider, or your system itself, but I could not guess beyond
that as it is all system/case specific.
If possible, try the steps below and let us know what your results are.
Attempt the upload from a different internet connection
Attempt the upload from a different system.
Make sure your are using Internet Explorer 9 or higher.(It is not required, but our tools are designed for that browser)
Clear your system cache, and restart
I am sorry you are having problems with the upload. No system concerns on our end, so I hope these steps prove fruitful for you. Thanks again for the post!
- Robert -
Hello,
I'm using Jdeveloper 10.1.3.0.3.3412 on a Mac with a MySQL database. In Jdeveloper i can make a connection to the database and create adf business components
I've made a JSP page with ADF on a single table. No errors when compiling. When I try to run the JSP Page using Embedded OC4J (on Mac OSX Tiger) I get the error:
5/12/09 00:45:50 java.net.ConnectException: Connection refused
05/12/09 00:45:50 at java.net.PlainSocketImpl.socketConnect(Native Method)
05/12/09 00:45:50 at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333)
05/12/09 00:45:50 at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195)
05/12/09 00:45:50 at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182)
05/12/09 00:45:50 at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:428)
05/12/09 00:45:50 at java.net.Socket.connect(Socket.java:507)
05/12/09 00:45:50 at java.net.Socket.connect(Socket.java:457)
05/12/09 00:45:50 at java.net.Socket.<init>(Socket.java:365)
05/12/09 00:45:50 at java.net.Socket.<init>(Socket.java:207)
05/12/09 00:45:50 at oracle.jdevimpl.runner.oc4j.Oc4jNotifier.sendMessage(Oc4jNotifier.java:98)
05/12/09 00:45:50 at oracle.jdevimpl.runner.oc4j.Oc4jNotifier.postInitApplicationServer(Oc4jNotifier.java:55)
05/12/09 00:45:50 at com.evermind.server.ApplicationServer.serverExtensionPostInit(ApplicationServer.java:1041)
05/12/09 00:45:50 at com.evermind.server.ApplicationServer.setConfig(ApplicationServer.java:927)
05/12/09 00:45:50 at com.evermind.server.ApplicationServerLauncher.run(ApplicationServerLauncher.java:98)
05/12/09 00:45:50 at java.lang.Thread.run(Thread.java:613)
What am I doing wrong? The embedded OC4J library is added to the project. I've tried to use the javac compiler. It looks like the OC4J instance cannot make a connection to the db.
Thanks,
MartinHello
I've added the connection to the web.xml, but still get the same error.
When I go to embedded OC4J preferences and change the JNDI-names of the datasources (global and current-workspace) to the same name (this was default), i get this error message:
9-dec-2005 9:30:09 com.evermind.server.ApplicationStateRunning initNativeDataSource
SEVERE: Error creating native data source. The location 'jdbc/MySQLConnectionCoreDS' is already in use.
05/12/09 09:30:09 Application: current-workspace-app is in state FAILED
05/12/09 09:30:09 Error instantiating application 'current-workspace-app' at file:/Users/martinsuijs/jdevhome/mywork/myWorldApp/myWorldApp-oc4j-app.xml: Error creating native data source. The location 'jdbc/MySQLConnectionCoreDS' is already in use.
05/12/09 09:30:14 java.net.ConnectException: Connection refused
grtz
Martin -
RFC logon failed with message: Failed: Connect to SAP gateway failed
I installed CI instance fine and i am stopped here with this error at the end of DB instance install. Could someone let me know what could be the reason for this. Is there any fix or workaround to continue the install.
INFO 2006-09-16 01:13:02 [iaxxrfcimp.cpp:398]
CAbRfcImpl::setRfcConnectParam
RFC parameter ASHOST set to value hostSAP.
INFO 2006-09-16 01:13:02 [iaxxrfcimp.cpp:398]
CAbRfcImpl::setRfcConnectParam
RFC parameter SYSNR set to value 09.
INFO 2006-09-16 01:13:02 [iaxxrfcimp.cpp:543]
CAbRfcImpl::checkConnectInfo
RFC connection information checked successfully.
ERROR 2006-09-16 01:13:02 [iaxxrfcimp.cpp:450]
CAbRfcImpl::openRfcConn
FRF-00007 Unable to open RFC connection.
ERROR 2006-09-16 01:13:02
CJSlibModule::writeError_impl()
FRF-00063 RFC logon failed with message: Failed: Connect to SAP gateway failed
Connect_PM GWHOST=hostSAP, GWSERV=sapgw09, ASHOST=hostSAP, SYSNR=09
LOCATION CPIC (TCP/IP) on local host
ERROR partner not reached (host hostSAP, service 3309)
TIME Sat Sep 16 01:13:02 2006
RELEASE 640
COMPONENT NI (network interface)
VERSION 37
RC -10
MODULE nixxi_r_mt.cpp
LINE 8528
DETAIL NiPConnect
SYSTEM CALL connect
ERRNO 146
ERRNO TEXT Connection refused
COUNTER 4
Thanks,
Ramat the end of the database instance installation SAPInst is doing some RFCs to the CI.
The logfile states that the gateway on host hostSAP with the systemnumber 09 is not reachable.
Please check if you have started the central instance on this machine.
peter -
Grid installtion failing with error Cannot connect to Node Manager. : Conf
I am trying to install Grid, however its failing with following error
I installed Weblogic server 10.3.4 and 11g R2 database
==============================================================
Code of Exception: Error occured while performing nmConnect : Cannot connect to Node Manager. : Configuration error while reading domain directory
Use dumpStack() to view the full stacktrace
Thu Mar 03 21:49:03 IST 2011
<traceback object at 1>
Connecting to Node Manager ...
This Exception occurred at Thu Mar 03 21:49:03 IST 2011.
Thu Mar 03 21:49:03 IST 2011
SEVERE: Exception: during stop of admin server
Thu Mar 03 21:49:03 IST 2011
Name of Exception: main.WLSTException
Thu Mar 03 21:49:03 IST 2011
Code of Exception: Error occured while performing nmConnect : Cannot connect to Node Manager. : Configuration error while reading domain directory
Use dumpStack() to view the full stacktrace
Thu Mar 03 21:49:03 IST 2011
<traceback object at 2>
Connecting to Node Manager ...
This Exception occurred at Thu Mar 03 21:49:03 IST 2011.
Thu Mar 03 21:49:03 IST 2011
Node Manager is not running
Mar 3, 2011 9:49:03 PM oracle.sysman.omsca.util.CoreOMSConfigAssistantUtil execCommand
INFO: error messages of the command :
weblogic.nodemanager.NMException: Configuration error while reading domain directory
at weblogic.nodemanager.client.NMServerClient.checkResponse(NMServerClient.java:301)
at weblogic.nodemanager.client.NMServerClient.checkResponse(NMServerClient.java:314)
at weblogic.nodemanager.client.NMServerClient.connect(NMServerClient.java:249)
at weblogic.nodemanager.client.NMServerClient.checkConnected(NMServerClient.java:200)
at weblogic.nodemanager.client.NMServerClient.checkConnected(NMServerClient.java:206)
at weblogic.nodemanager.client.NMServerClient.getVersion(NMServerClient.java:53)
at weblogic.management.scripting.NodeManagerService.verifyConnection(NodeManagerService.java:179)
at weblogic.management.scripting.NodeManagerService.nmConnect(NodeManagerService.java:173)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.python.core.PyReflectedFunction.__call__(Unknown Source)
at org.python.core.PyMethod.__call__(Unknown Source)
at org.python.core.PyObject.__call__(Unknown Source)
at org.python.core.PyObject.invoke(Unknown Source)
at org.python.pycode._pyx2.nmConnect$3(<iostream>:118)
at org.python.pycode._pyx2.call_function(<iostream>)
at org.python.core.PyTableCode.call(Unknown Source)
at org.python.core.PyTableCode.call(Unknown Source)
at org.python.core.PyFunction.__call__(Unknown Source)
at org.python.core.PyObject.__call__(Unknown Source)
at org.python.pycode._pyx41.stopManagedServer$6(/u02/oracle/Oracle/Middleware/oms11g/sysman/omsca/scripts/wls/start_server.py:142)
at org.python.pycode._pyx41.call_function(/u02/oracle/Oracle/Middleware/oms11g/sysman/omsca/scripts/wls/start_server.py)
at org.python.core.PyTableCode.call(Unknown Source)I am still getting error, even after installing Weblogic server 10.3.2
ar 4, 2011 10:44:42 AM oracle.sysman.omsca.util.CoreOMSConfigAssistantUtil execCommand
INFO: error messages of the command :
weblogic.nodemanager.NMConnectException: Connection refused. Could not connect to NodeManager. Check that it is running at node1.slksoft.com:7,403.
at java.net.PlainSocketImpl.socketConnect(Native Method)
at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333)
at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195)
at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182)
at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366)
at java.net.Socket.connect(Socket.java:525)
at weblogic.nodemanager.client.SSLClient.createSocket(SSLClient.java:38)
at weblogic.nodemanager.client.NMServerClient.connect(NMServerClient.java:227)
at weblogic.nodemanager.client.NMServerClient.checkConnected(NMServerClient.java:199)
at weblogic.nodemanager.client.NMServerClient.checkConnected(NMServerClient.java:205)
at weblogic.nodemanager.client.NMServerClient.getVersion(NMServerClient.java:52)
at weblogic.management.scripting.NodeManagerService.verifyConnection(NodeManagerService.java:175)
at weblogic.management.scripting.NodeManagerService.nmConnect(NodeManagerService.java:168)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.python.core.PyReflectedFunction.__call__(Unknown Source)
at org.python.core.PyMethod.__call__(Unknown Source)
at org.python.core.PyObject.__call__(Unknown Source)
at org.python.core.PyObject.invoke(Unknown Source)
and also i am getting below error.
oracle@node1 grid]$ export ORACLE_SID=prod
[oracle@node1 grid]$ emctl status agent
EM Configuration issue. /u01/oracle/product/11.2.0/db_1/node1.soft.com_prod not found.
[oracle@node1 grid]$ -
Hi all,
I'm investigating cause of a wedged wiki this morning. The MacMini (10.7.5) was working well for the last year but we're not sure when it gave up the ghost.
I've already applied the fixes detailed at Mac OS X v10.5, Mac OS X Server v10.5: Web, Mail, Wiki, Personal Web Sharing, Parental Controls services may not start after restoring a Time Machine backup but it has't helped.
The error we see when we visit the top level of the server is:
Service Temporarily Unavailable
The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.
Apache/2.2.22 (Unix) PHP/5.3.15 with Suhosin-Patch mod_ssl/2.2.22 OpenSSL/0.9.8r DAV/2 Server at sacmini.local Port 80
The message in the httpd error logs is:
Connection refused: proxy: HTTP: attempt to connect to failed [error] ap_proxy_connect_backend disabling worker
Let me know if you have any ideas. Thank you.
--AthoniaThanks for the reply.
So, there were some Ruby related log file entries. Do these have any meaning to you? I'm checking to see what collabcored2 does exactly.
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib/ruby/1.8/rubygem s/custom_require.rb:31:in `require'
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /usr/share/collabd/coreclient/config/environment.rb:11
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib/ruby/1.8/rubygem s/custom_require.rb:31:in `gem_original_require'
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib/ruby/1.8/rubygem s/custom_require.rb:31:in `require'
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /usr/share/collabd/coreclient/config.ru:13
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /Library/Ruby/Gems/1.8/gems/rack-1.2.1/lib/rack/builder.rb:46:in `instance_eval'
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /Library/Ruby/Gems/1.8/gems/rack-1.2.1/lib/rack/builder.rb:46:in `initialize'
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /usr/share/collabd/coreclient/config.ru:1:in `new'
May 7 14:22:33 sacmini com.apple.collabcored2[22106]:
from /usr/share/collabd/coreclient/config.ru:1
May 7 14:22:33 sacmini com.apple.launchd[1] (com.apple.collabcored2[22106]): Exited with code: 1
May 7 14:22:33 sacmini com.apple.launchd[1] (com.apple.collabcored2): Throttling respawn: Will start in 9 seconds -
RFC connection (SM59) fails with load balancing enabled.
Hello All,
We have an RFC connection setup between two SAP systems. The RFC connection works fine if it points to the destination system. But if we enable load balancing, the connection fails with this error:
ERROR partner not reached (host <hostname>, service sapms<SID>)
LOCATION SAP-Server <source system> on host <host name of source> (wp 1)
DETAIL NiPConnect2
CALL SO_ERROR
COMPONENT NI (network interface)
COUNTER 3027
ERROR TEXT Connection refused
ERROR NUMBER 79
MODULE niuxi.c
LINE 1069
RETURN CODE -10
SUBRC 0
RELEASE 46D
TIME Mon Aug 18 18:33:30 2008
VERSION 34
I've checked the /etc/services file, the following entries exist
sapms<SID> 3606/tcp
sapms<SID>s 3600/tcp
lstst at the source system works fine
lgtst -H <target host name> -S sapms<SID>
niping at the target system has a problem
> niping -c -S 3606
Mon Aug 18 10:23:14 2008
connect to server o.k.
ERROR => NiTClientLoop: NiTReadLoop (rc=-6) [nixxtst.cpp 2629]
ERROR connection to partner broken
TIME Mon Aug 18 10:23:14 2008
RELEASE 640
COMPONENT NI (network interface)
VERSION 37
RC -6
MODULE niuxi.c
LINE 905
DETAIL NiPRead (0.0.0.0/0, hdl 1)
SYSTEM CALL recv
COUNTER 1
Please help me figure out the problem.
regards,
RoshniHi,
I think you have added wrong port entry in services file.
The entry of sap servers in services file for load balancing are
sapms<SID> 36<instance number>/tcp
so please check once again and add the entry using above formula in services file.
Also add the entry of all SAP servers in your hosts file.
<IP> <HOSTNAME>
Maybe you are looking for
-
Tracking Mouse X,Y w/o mouseListener
I am writing a program where you draw with a paintbrush, you begin a stroke by clicking, you end a stroke by releasing. This was easily taken care of by a simple mouseListener. However I want to track everywhere the mouse goes while the mouse is clic
-
Changes that are needed for RVADIN01
hi, i am using Standard SapScript Driver Program RVADIN01 for my smartform, smart form i am developing from scratch. which will creates invoice, Credit Request, Debit Request. to make use of this driver program for my smart form what are the relevent
-
Reference using the name assigned with setName
I am automatically generating a data update screen that displays labels and associated data fields. The labels and fields are generated based on the field names and types contained in a SQL table. As the fields are generated the field name is set to
-
I have new wmail notification ballon but no new mails.
Dear All, I have IPHONE 5 latest IOS 6.1.3 I am using company exchange acount for my job mails and recenetly i have new mail ballon on the email icon but no new mail available. i also marked all as read in outlook but still have the 1 new mail ballon
-
my iphone 4s shuts itself off all the time. starts normal and then shut it off and start all over again, what is wrong?