SCCM - Credentials prompt in user PC and then my screen goes black
Hi, when I use SCCM to connect to a pc for a security reason when I do something in the Users PC and it asks for the admin password in my screen ( using remote ) it stays black. I understand why, but, my question is. How can I be able to Put the credentials
remotly too ? Is there a way for the credentials prompt appear in my computer too?
Thanks!
I assume you are using remote assistance via SCCM? If so, enable the following Group Policy Setting
Computer Config\Policies\Windows Settings\Security Settings\Local Policies\Security Options\User Account Control\User Account Control: Allow UIAccess applications to prompt for elevation without using the secure destkop
Similar Messages
-
PlayBook lags and then the screen goes black and does not respond
Hello guys,
As the Subject line summarizes, my tablet was working like charm since the date of purchase, back then in April last year. However, on these days it has been performing weird. It has always been fast and smooth, but since last week it has been lagging and not no responsive to the touch.
To tell you gusy fast and clear, it boots up as normal, fast and smooth, apps open and close as usual. Then it starts to lag, and freezes for one second, responds and freezes again but this time will not respond again and finally the screen goes black and stucks there until I make a hard reset and it reboots normally, until it does it again, and again.
Relevant information:
16GB model, 1.5GB free storage available, sideloaded a few android apps today, recorded a few videos
the device manager software on the pc makes no difference, as the PB will anyway freeze and go all black even if it's backing up or something.
HELP?Make sure any important data is backed up preferably by drag and drop to a pc.
When it is working properly, try gently squeezing the playbook between finger and tbumb around the black bezel border. Especially either side of the lower sockets. If it goes black it's probably a bad battery or screen contact.
1.5 GB is not much spare storage, by the way. I would never fill more than 75%. -
I have a PB G4 that won't start. It shows the gray apple screen, shows the blue screen, and then goes black. The sleep light pulses. From there, I can't turn it off normally. I have tried restarting the PMU. And I have tried unplugging the ac adaptor and removing the battery. From there I have plugged only the ac adaptor in, and it will begin to start but do the same thing once it shows the blue screen.
I tried only using the battery (without plugging in the ac adaptor) and the same thing happens. I tried starting the computer while holding down CTRL, Option, P, and R, waiting to hear the start up chimes 3 times, and then holding Shift as it starts up. But I still get the black screen once I see the blue one, and the computer's sleep light pulses.
I need something very important from this computer. And was able to start it last night. I did not shut down the computer, and was going to take it to a friends to use his printer today. The computer was in sleep mode in the morning.
Thanks for any help!
GinaWhat your describing could be a logic board or memory issue.
You did or did not hear 3 startup chimes? If you hear 3 chimes when you start it, that would indicate a memory problem. Try reseating the memory to see if that makes a difference. If you have 2 RAM cards, try one then the other in each slot. If you have 1 RAM card, move it to the other slot. Powerbooks can develop one bad slot.
You may need to pull the hard drive out of the Powerbook, put it into an external case, then read it from another mac. -
I have a 5th gen nano, and I play it often on a aux. speaker. I would like the album artwork to display at all times while playing it here. Right now it plays for a few seconds on each song, and then goes blank. Can this be changed?
The artwork turns black or the screen's backlight turns off? If the backlight turns off, simply disable the backlight timer, but keep in mind this will significantly reduce your iPod's playback time and battery life.
B-rock -
Boots to black in OS X mode (I believe 10.10.2? tough to check right now). I can boot into Windows 8 using Boot Camp without incident. I have booted to Disk Utility and run Disk and Permissions Repair. I have booted into Diagnostics, and no issues were found (ADP000 was the Reference Code given). I reset the PRAM, which gave a louder chime than I had been getting when failing to start up OS X, but otherwise no change. Feeling that my options were exhausted, I attempted to restore from Time Capsule, and it won't connect to Time Capsule, despite Time Capsule being the active router whose network I am connected to. Please advise.
(This is my girlfriend's computer, she tells me that she selected an option to perform an automatic update later, that night.)Install or Reinstall OS X from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
the Security button and set the Zero Data option to one-pass. Click on
the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.
This should install the version of OS X that you had installed.
Be sure you only work on the OS X volume, not your Windows volume. I cannot tell you if you will still be able to boot the Windows volume after the above. You will need to find a fix for that. -
just bought a new iphone4 and was loading os6 and now it won't turn on. the apple glows like it is starting up, then the screen goes black and then repeats the same process over and over. i have tried to reboot multiple times now
I am assuming the phone was working prior to you installing IOS 6? Did you use itunes to install IOS 6 or just run from the phone?
When I tried to do the Over The Air update to IOS6 on my iPhone 4, it errored out and I had to connect it to iTunes and select "Restore" from the summary screen after iTunes finds the phone is connected. If this works for you, it will go through a couple of reboots that take a few minutes to complete. It should then give you the option to start with a fresh new phone or to use one of your previous backups to load your contacts and other information, provided you have backed up the phone previously.
I hope this helps you my friend! -
When I click on my Messages app I can see it for a brief moment and then the screen goes blank
When I click on my Messages app I can see it for a brief moment and then the screen goes blank. This happened to me last week and I Reset All Settings, which worked-but it has just happened again so that's not a long-term solution.
Hello linslaf,
It may help to force close the Messages app, then restart the device.
iOS: Understanding multitasking
http://support.apple.com/kb/HT4211
iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
If the issue persists, the next step would be to restore your iiPhone.
iOS: Back up and restore your iOS device with iCloud or iTunes
http://support.apple.com/kb/HT1766
Cheers,
Allen -
When I click on itunes store it displays it for a few seconds and then the screen goes blank?
When I click on the itunes store the info appears for a couple of seconds and then the screen goes blank. I never had this problem before any ideas?
same thing with me have you found an answer? the only thing i cant think of is to download the new itues but when i try they are haveing problems with the site or something and i cant dowload it.
-
My itouch won't turn on. All that shows is the apple icon and then the screen goes blue to white. Is there a way to fix this or is my itouch unfixable? HELP ME!!!
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I tried replacing the screen with no luck. The same thing happened with the new screen. I replaced the backlight coil and the backlight ic and still have the issue. I don't know what else could be the problem. If the battery is completely dead and I plug it in the "charging battery" symbol shows just fine during the entire time it is charging, but as soon as it starts to boot up the apple logo shows for a split second then the screen goes black. The rest of the phone still boots up just fine. I can use SIRI, press the lock button like I'm about to use my phone and slide my thumb across where the "slide to unlock" would normally be and it will make the unlock noise just no picture display. I am pretty tech savvy when it comes to repairs and all of the connections look fine, replaced backlight coil and ic, replaced LCD/digitizer, tried a restore, tried a DFU restore, multiple hard resets, but I am at a loss as to where to go from here. I had dropped the phone and put a minor crack in the screen but the phone worked just fine for a couple months after before this started to happen. The phone is still under apple warranty but apple won't cover it because Apple is stating that it is "caused by the crack in the screen." But being a repair technician I know that is not the case... Good one apple. So I took it upon myself to try to determine the REAL problem. Anyone with a little more knowledge have any ideas? Any suggestions are appreciated!!
Yes, I understand that. But The screen issue is not a result of user damage. The phone was not dropped when the screen got cracked. My daughter was standing in a chair at the table and dropped one of her toys onto the bottom of the phone and cracked it right by the home button. (Nowhere near the LCD/digitizer flex cables, connections, or logic board components) then a few months later my phone had died, I plugged it in, it showed it was charging, then Apple logo disappeared and screen didn't work. AFTER contacting Apple about the issue and them telling me that it "is a result of the very minimal crack to the sheet of glass that has no relation to the LCD or Digitizer and that the warranty does not cover it I had taken it upon myself to change the LCD/digitizer to no avail, as well as backlight ic and backlight coil to no avail. But how do I go about letting Apple know that it is in fact NOT due to the cracked screen nor is it due to the flex cable connections? I can't. So the lady that works the call center phones trying to "convince" me that she knows what she is talking about and "convince" me that it is from the cracked screen I have to take her word because I can't show Apple that its not because of that without paying them $199 to fix the screen in which case they will just send me a new phone rather than fix the faulty hardware under warranty.
-
Hello friends I turned on my Mac book pro there was a flicker of light and then the screen went dark ?please help
Did you buy the Applecare extended warranty? If not then you will need to pay for whatever repairs need to be done.
You will need to take the system to an Apple store Genius Bar for a check up. -
Encore WT8-A starts to turn on but then the screen goes black!?
This began nearly a week ago, I had just installed a few apps and my battery died. When I tried to turn the tablet back on it showed a dark blue or even greyish screen. I waited over night and tried turning it out again...this time it began to start, showing the Toshiba start up screen, but then the screen went black.
I have tried to hold the power button, does not work. It will only partially work while on the charger, nothing happens unless it is plugged in.
I did do a Google search and found out that this could be a Bitlocker problem so I tried once again after waiting a few days, I was able to get to a screen allowing me o input a recovery key. The recovery key worked and then I was sent to a page saying that my PC started wrong, restart. When I allow it to do so the process starts all over again...
This tablet is only about 6 months old and I just started using it regularly a few months ago. It hasn't been damaged and I am certain there is no virus because I have software that I run weekly. I am clueless as to what to do to make this work. Has anyone else experienced this problem, if so how was it resolved?It seems that a few months ago Toshiba started shipping devices with Bitlocker enabled (one I bought a year ago did not have, one I bought in November did. I turned it off and decrypted the drive immediately.This seems to be an industry problem and not just Toshiba. "Someone" made a firmware revision that turned it back on since other Tablets have reported the same problem.
I have seen reports of three stages of Bitlocker:
1) Not encrypted - no key
2) Encrypted using a personal key (may be stored in your Microsoft account and recovered from there - is about 25 digits)
3) Encrypted but Bitlocker turned off. Key stored on hard drive and "decrypted on the fly". I suspect this is the problem and happens if Bitlocker is turned off but the drive is not decrypted (takes several minutes). If something happens to "lose" the key then there is a problem. I suspect the key is stored in the firmware (BIOS) and an update may wipe it..
What I would do for any tab is two things:
1) Open diskmgmt.msc and see if any drive mentions Bitlocker
2) Go to "Search" and enter "drive encryption". See what it says
If either mentions Bitlocker or "drive is encrypted" then I would go to Control Panel>Security>Bitlocker and decrypt the drive (not just turn off). If you need disk encryption then make sure you keep a copy of the key offline.
If that does not work or it is locked already then a full recovery with reformat may be needed. -
my iphone was charging and then turned off and vant get it back on and tried resetting it with the home button...what can i do??
iPhone User Guide
Try this...
Turn the Phone Off... ( if it isn’t already )
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear and then Disappear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
Turn the Phone On... -
It was about 30MB, it was loading and then I turned off the screen. A few minutes later I tried turning it back on and it stayed black. I tried connecting it to my Macbook Pro and it says that its receiving a wrong response. What could be wrong?
Have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider if it appears), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
-
power light goes on the immediately goes off, screen show apple then goes black without turning onn
You can try disabling emoticons and image previews in your IM appearance settings in your Skype options to see if that changes anything. Some people running Windows XP have had odd graphical and resource issues with versions of Skype above 7.5. The alternative solution would be to downgrade to Skype 7.5 for the time being. You can find links to 7.5 in the thread below. http://community.skype.com/t5/Windows-desktop-client/Skype-7-6-crashes-on-startup/m-p/4031560/highlight/true#M353247
Maybe you are looking for
-
Hi All, I am deploying my application from JDeveloper remotely in Oracle 10g AS.in my application I have generated a couple of reports using Oracle Report Writer.basically i generated report JSPs.when I run my application report is not getting genera
-
Group 8 channel (binary) to octal/hexadecimal
Hi, Let say I have 8 channel of binary data in array and plotted to the graph. If button "Grouping" pressed, then the 9th channel will be plotted, which is in octal value (Sum of binary value at the same sample). <Please refer to the picture attach>.
-
When I sync my photo's from my computer to my i-phone they appear in a random order and some of them are duplicated. How can I get them to appear as they are saved in my folders on my computer?
-
Enabling Usage Rights on Livecycle PDF Causes Problems with Table
I have a form that uses a script to dynamically add rows to a table. Everything works great, except that once I enable usage rights on the PDF, the header row repeats 3 times on the document. LINK TO DOCUMENT WITHOUT USAGE RIGHTS (link removed) Eve
-
Field restrictions set in SWEC for BUS2012.
Hi Gurus, The field restrictions have been set for fields (ekpo-menge, ekpo-netpr etc..). But this doesnot seem to work. The workflow triggers if there is any change in the PO. This should not happen. Please help in this regards. Thanks, Sathish.