SCCP FXS on 2911 with CUCM 10.X

Dears
CUCM >>> SCCP >>> ISR 2911 with fxs ports
this is my senario
the FXS is register on CUCM, a FAX is connected to the FXS i can call it but it will not ring
during the call when i press reset button the call will be disconnected means it's fully registered with the CUCM but i don't know what is the problem here
CONFIGURATION USED::
=============================
stcapp ccm-group 1
stcapp
stcapp feature access-code
stcapp feature speed-dial
stcapp call-control mode feature
voice-card 0
dsp services dspfarm
voice service pots
fax rate disable
voice service voip
no ip address trusted authenticate
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol pass-through g711alaw
sip
early-offer forced
midcall-signaling passthru
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice-port 0/0/0
cptone GB
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
ccm-manager config server 172.28.34.11
ccm-manager config
ccm-manager sccp local GigabitEthernet0/0
ccm-manager sccp
sccp local GigabitEthernet0/0
sccp ccm 172.28.34.11 identifier 1 version 7.0
sccp ccm 172.28.34.12 identifier 2 version 7.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate ccm 2 priority 2
switchback method immediate
dial-peer voice 8940 pots
service stcapp
port 0/0/0
ANY HELP ......
Thanks

How are you connected to the PSTN? Sip trunk?
When you check the configuration of you FXS port in call manager, does it look like this?:
Product
Cisco MGCP FXS Port
Gateway
RI-3925-CUBE
Device Protocol
Analog Access
Device is not trusted
Registration
Registered with Cisco Unified Communications Manager 10.0.17.6
IP Address
10.0.12.2
End-Point Name
AALN/S0/SU3/0@RI-3925-CUBE
Thanks,
Frank

Similar Messages

CME B-ACD on Cisco 2911 with IOS 15.2(4)M5 not working

Hi Folks,
I am currently setting up CME version 9.1 with B-ACD (app-b-acd-aa-3.0.0.2.tcl & app-b-acd-3.0.0.2.tcl), running on
Cisco 2911 with IOS ver 15.2(4)M5, this is for lab purposes.
Below is my CME & B-ACD configuration :
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 listen-port 1820
no call service stop
sip
bind control source-interface Vlan400
bind media source-interface Vlan400
registrar server expires max 600 min 60
voice register global
mode cme
source-address 172.25.202.1 port 5060
max-dn 2
max-pool 2
load 9971 sip9971.9-2-2SR1-9
authenticate register
timezone 28
time-format 24
date-format D/M/Y
tftp-path flash:
create profile sync 0004714411607756
voice register dn 1
number 3005
name br2phn2
voice register dn 2
number 3006
name br2phn4
voice register template 1
dialplan 1
voice register dialplan 1
type 7940-7960-others
pattern 1 3...
pattern 2 999
voice register pool 1
id mac 1C1D.86C4.0D6D
type 9971
number 1 dn 1
template 1
dtmf-relay rtp-nte
username 3005 password cisco
description 3214-3005
codec g711ulaw
voice register pool 2
id mac 1C1D.86C4.A574
type 9971
number 1 dn 2
template 1
dtmf-relay rtp-nte
username 3006 password cisco
description 3214-3006
codec g711ulaw
voice hunt-group 1 parallel
list 3002,3006
pilot 3210
application
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param number-of-hunt-grps 2
param handoff-string aa
paramspace english language en
param max-time-vm-retry 2
param aa-pilot 3500
paramspace english location flash://
param second-greeting-time 60
param welcome-prompt _bacd_welcome.au
param call-retry-timer 15
param voice-mail 3001
param max-time-call-retry 90
param service-name queue
service aa-drop flash:/app-b-acd-aa-3.0.0.2.tcl
paramspace english index 1
param service-name queue
param drop-through-option 2
param second-greeting-time 60
paramspace english language en
param max-time-vm-retry 2
param max-time-call-retry 90
param voice-mail 3001
paramspace english location flash://
param aa-pilot 3501
param number-of-hunt-grps 1
param handoff-string aa-drop
param call-retry-timer 15
service queue flash:/app-b-acd-3.0.0.2.tcl
param queue-len 15
param aa-hunt10 3006
param queue-manager-debugs 1
param number-of-hunt-grps 2
param aa-hunt2 3210
interface Loopback0
ip address 172.25.110.3 255.255.255.255
ip ospf network point-to-point
h323-gateway voip interface
h323-gateway voip id Spain ipaddr 172.25.110.1 1719
h323-gateway voip h323-id BR2-RTR
h323-gateway voip tech-prefix 1#
h323-gateway voip bind srcaddr 172.25.110.3
interface Vlan400
ip address 172.25.202.1 255.255.255.0
ip pim dense-mode
dial-peer voice 3500 voip
service aa
destination-pattern 3500
session target ipv4:172.25.110.3
incoming called-number 3500
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 3501 voip
service aa-drop
destination-pattern 3501
session target ipv4:172.25.110.3
incoming called-number 3501
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
telephony-service
no auto-reg-ephone
max-ephones 2
max-dn 2 no-reg both
ip source-address 172.25.110.3 port 2000
cnf-file location flash:
load 7965 term65.default.loads
time-zone 28
time-format 24
date-format dd-mm-yy
max-conferences 8 gain -6
moh "music-on-hold.au"
web admin system name admin password cisco
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 14 2014 05:54:44
ephone-template 1
softkeys connected Endcall Hold Park Trnsfer Acct Flash
ephone-dn 1 octo-line
number 3001 no-reg both
description 3214-3001
name br2phn1
ephone-dn 2 octo-line
number 3002 no-reg both
description 3214-3002
name br2phn3
ephone 1
device-security-mode none
mac-address 189C.5DB6.D303
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7965
button 1:1
ephone 2
device-security-mode none
description 3214-3002
mac-address 984B.E194.FDDD
ephone-template 1
max-calls-per-button 5
busy-trigger-per-button 3
type 7960
button 1:2
Problem :
1. When I test call from CME Phone both SIP and SCCP Phone by dial 3500 or 3501, I get the busy tone.
2. Debug voip dial-peer, match with dial-peer voice 3500 for (aa service) & 3501 for (aa-drop service).
3. Debug voice application script, show nothing.
Is there something wrong with my configuration ?
Rgds
Novri

Hi Novriadi,
In your configuration
service aa flash:/app-b-acd-aa-3.0.0.2.tcl
service queue flash:/app-b-acd-3.0.0.2.tcl
paramspace english location flash://
Remove "/" and "//" from the configuration
Then use the call application voice load command in privileged EXEC mode to reload the scripts.
Router# call application voice load aa
Router# call application voice load queue
Router# call application voice load aa-drop
You can refer to following document as well for more info
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/bacd/configuration/guide/cme40tcl/40bacd.html#wp1018270
Please find the sample configuration that is required to configure b-acd in CME for reference.
telephony-service
moh music-on-hold.au
multicast moh 239.1.1.1 port 2000
application
service queue flash:app-b-acd-2.1.0.0.tcl
param number-of-hunt-grps 2
param aa-hunt2 1111
param aa-hunt3 1222
param queue-len 15
param queue-manager-debugs 1
service aa flash:app-b-acd-aa-2.1.0.0.tcl
paramspace english index 1
paramspace english language en
paramspace english location flash:
param service-name queue
param handoff-string aa
param aa-pilot 8005550123
param welcome-prompt _bacd_welcome.au
param number-of-hunt-grps 2
param dial-by-extension-option 1
param second-greeting-time 60
param call-retry-timer 15
param max-time-call-retry 700
param max-time-vm-retry 2
param voice-mail 5003
dial-peer voice 222 voip
service aa
destination-pattern 8005550123
session target ipv4:192.168.1.1
incoming called-number 8005550123
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
Thanks & Regards,
Mudit Mathur

VG202XM SRTP Configuration with CUCM

Hi,
we want to use SRTP on our VG202XM. We use CUCM9.1 and want to use SCCP for the VG202XM. Also we want to use Feature Access Codes, so MGCP for the VG is not possible.
The only configuration i found for SRTP is for VG224.
http://www.cisco.com/en/US/partner/docs/ios/voice/fxs/configuration/guide/fsxsecur.html#wp1076224
There in the restirction you can see.
"This feature is not supported for analog SCCP endpoints in Cisco Unified Communications Manager."
Does someone have a configuration for this.
Best Regards
Daniel

Hi Daniel,
FAC with SRTP is supported with 15.1(3)T or later and with CUCM version 8.6 or later.
To configure the SRTP on GW/CUCM, Please use the following:
http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccptlscm.html
HTH
Manish

No ringbacktone for inbound calls with cucm 8.6

Hi,
we have this problem from many days...
we have two branches with cucm cluster(Publisher and Subscriber) at Head office and cisco untiy.The branches are connected to Head office through MPLS vpn and all the ip phones are registred to publisher located at headoffice.
our setup is like below
HO and BR2 having SIP lines and BR1 has PSTN Lines.
we implement greetings for head office and 2 branches at Headoffice Unity.
when any call comes to headoffice gateway the greetings will be played and call will be diverted to the appropriate extension.everything is fine.
But the problem is when the call comes to Branch gateway and the greetings will be played and the call gets diverted to the IP phone to which the caller dialed the extension. but the caller is not hearing the ringback tone while the extension is ringing. and the caller cannot know whether the extension is ringing or the call got disconnected.
i tried to change the " Send h225 User Information Message" in service parameters from "Use ANN for Ring Back" to H225 Info for call Progress Tone"
whenever i am changing to "H225 Info for call Progress Tone" then the branches problem getting solved but Headoffice getting the same problem.
please can anyone help............................

Hi Carlo,
Thankyou for the Response...
here is the Runn config for BR1 Connected to PSTN lines....
voice-card 0
dspfarm
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
h323
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g729br8
voice class h323 1
h225 timeout tcp establish 3
interface Tunnel100
description " Tunnel JED-RYD "
bandwidth 2048
ip address 10.10.0.1 255.255.255.252
tunnel source 172.31.217.202
tunnel destination 172.31.3.18
interface FastEthernet0/0
description DAMMAM Local LAN
no ip address
duplex auto
speed auto
interface FastEthernet0/0.20
description JEDDAH Local LAN
encapsulation dot1Q 20
ip address 192.168.20.5 255.255.255.0
interface FastEthernet0/0.21
description JEDDAH VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.5 255.255.255.0
h323-gateway voip interface
h323-gateway voip bind srcaddr 192.168.21.5
interface FastEthernet0/1
ip address 172.31.217.202 255.255.255.252
duplex auto
speed auto
router eigrp 200
network 10.10.0.0 0.0.0.3
network 192.168.20.0
network 192.168.21.0
no auto-summary
router bgp 65412
no synchronization
bgp log-neighbor-changes
neighbor 172.31.217.201 remote-as 65000
no auto-summary
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.20.1
ip route 192.168.20.50 255.255.255.255 192.168.20.1
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
access-list 23 permit 10.10.10.0 0.0.0.7
control-plane
voice-port 0/0/0
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/0/1
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/0/2
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/0/3
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/2/0
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
connection plar 2022
shutdown
impedance complex2
description STC
voice-port 0/2/1
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
shutdown
impedance complex2
description STC
voice-port 0/3/0
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/3/1
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/3/2
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
voice-port 0/3/3
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx 2050
impedance complex2
description STC
caller-id alerting dsp-pre-allocate
sccp local FastEthernet0/0.21
sccp ccm 192.168.12.190 identifier 1 priority 1 version 5.0.1
sccp ccm 192.168.12.189 identifier 2 priority 2 version 5.0.1
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 1 register CONFJEDRAW
associate profile 2 register TRNJED
associate profile 3 register MTPJED
switchover method immediate
switchback method immediate
switchback interval 15
dspfarm profile 2 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 2
associate application SCCP
dspfarm profile 1 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
shutdown
dspfarm profile 3 mtp
codec g729r8
maximum sessions software 250
associate application SCCP
shutdown
dial-peer voice 1 pots
dial-peer voice 1000 voip
description To CallManager - SBWPMPUB
destination-pattern [1-5]...
progress_ind progress enable 8
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.12.190
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 9001 pots
description ** 02-6140294(outgoing) **
destination-pattern [^2].T
port 0/0/1
dial-peer voice 9002 pots
description ** 02-6140295(outgoing) **
destination-pattern [^2].T
port 0/0/2
dial-peer voice 9003 pots
description ** 02-6140296(outgoing) **
destination-pattern [^2].T
port 0/0/3
dial-peer voice 9004 pots
description ** 02-6140293(outgoing) **
destination-pattern [^2].T
port 0/0/0
dial-peer voice 290 pots
incoming called-number .
direct-inward-dial
dial-peer voice 9006 pots
description ** 02-6529323(local) **
destination-pattern [^0].T
port 0/3/0
dial-peer voice 9010 pots
description ** 02-6578249(local) **
destination-pattern [^0].T
port 0/3/1
dial-peer voice 9011 pots
description "to pstn service"
shutdown
destination-pattern 0.T
port 0/3/3
dial-peer voice 9009 pots
description "to pstn service"
shutdown
destination-pattern [^0].T
port 0/3/2
dial-peer voice 9005 pots
destination-pattern .T
dial-peer voice 1001 voip
description To CallManager - Subscriber
destination-pattern [1-5]...
progress_ind progress enable 8
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.12.189
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 1002 voip
description " TO Unity Greetings"
destination-pattern 2050
progress_ind progress enable 8
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.12.190
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 1003 voip
description " TO Unity Greetings"
destination-pattern 2050
progress_ind progress enable 8
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.12.189
dtmf-relay h245-alphanumeric
no vad

Unity Express 8.6.7 intgration with CUCM 10?

I'm working on a 2911, with a ISM-SRE-300-K9 running CUE 8.6.7 (confirmed clean install). The CTI Ports are not registering with CUCM, all the steps have been triple checked, yet they don't register.
The CUE talks to CM fine and pulls the 4 CTI Ports we configured on CUCM, but if you click the 'show available ports in CUCM" it immediately crashes the CUE and it reboots.
I have a case open and it may be a bug, but wanted to see if anyone here has CUE working with CUCM 10.
Thanks-

Yes, confirmed that is all correct.
The ports don't register and when you click "expand to also show available ports on cucm" the CUE crashes:
CRASH appsServices startup startup.sh System has crashed. The trace buffer information is stored in the file "atrace_save.log". You can upload the file using "copy log" command
if I enable jtapi debugs, it just says out of service:
1936: Jun 03 14:38:03.212 EDT %JTAPI-MISC-7-UNK:(P42-x.x.x.x) ReceiveThread starting up...
1937: Jun 03 14:38:03.213 EDT %JTAPI-PROTOCOL-7-UNK:(P42-x.x.x.x) received Response: com.cisco.cti.protocol.FailureResponse {
sequenceNumber = 0
result = -1932787395
description = Provider Init is not done -- Open rejected
1938: Jun 03 14:38:03.214 EDT %JTAPI-PROTOCOL-7-UNK:(P42-x.x.x.x) received Event: com.cisco.cti.protocol.ProviderOutOfServiceEvent {
eventSequence = 41
PROVIDER_OUT_OF_SERVICE_EVENT = 200

ATA-186 can be registered with CUCM v10.5

Hello guys ;
Please confirm me that ATA-186 can work with CUCM v10.5 ? .
Regards;
Shib

Loaded the latest firmware into CM, then manually on ATA firmware using this process as CM didn't change it:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaapc.html#wp1011450
I followed this link from another post regarding ASA not registering for an older issue.
http://www.cisco.com/en/US/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccpaape.html#wpxref59054
Follow the part that mentions setting the SID0 & SID1 to "." no quotes. I did this and my ATA registered to CM. Screen caps attached.
I have a Cisco ATA 186 running on 10.5.1 and it shows to be registered. I can make calls on it. Not sure how it will do for faxes. HTH Please rate.

Jabber 9.6 no voicemail tab for CUC with CUCM 9 and CUC 8.6

Hi guys,
I have Jabber 9.2 and 9.6 clients with CUCM 9.1.2, CUC 8.5.1 and Cisco IM + P 9.1.1.
We've recently updated the CUCM and CUPS to Cisco IM+P. Also we have migrated from CUPC Clients to Jabber clients. The CUC server has remained as is. I was able to get the CUPC clients to get voicemail/visual voicemail but the Jabber client doesn't even display an ico for voicemail.
The service profile for all users is set correctly to point to the CUC server and there's no errors when I go to the jabber client "show connction status".
I haven't been able to find much about this issue. I have noticed that if I set the mail store the voicemail tab appears but we are not using a mail store as the voicemail repositary. Is this now required to check voicemail? If so can someone point me to the configuration guide? We have exchange 2012. Thanks very much!
-Akin

Hi every body,
I have some problems but not with all the users, is only working with 3 users and the rest of them don't work, I attached the errors that I get when I try to log in Telephony Accounts in the Jabber, I used the Jabber of one User, and from here I introduce my credentials (user and password) and I can get the voice mails (only from de 3 users that is woriking fine), but when I introduce the credentials of the other user I get the error and Can't get the voicemails.
The 127.23.0.7 is the IP address of the Cisco Unity Connection.
Please Help Me I'm stuck with this!

Cisco Jabber for Mac 9.2.1: slow to register with CUCM

Hi,
We have this specific problem on our Jabber for Mac 9.2.1 client only: the client takes 60 to 70 seconds to connect to CUCM (running 8.6.2) when it starts.
After Jabber registers with CUCM, there is no issue, it's just very slow to register.
Anybody getting the same behaviour? We have no such issue on previous versions of Jabber for Mac version 8 or Jabber for Windows version 9.
Thanks,
Fabrice

For those interested, I have the answer to my own question: if one of your configured DNS servers is not responding, Jabber 9.2.1 will delay registration to the phone services. This behaviour is seen only in this specifc version of Jabber, hopefully it will be fixed in the next release. Watch out if one of your DNS server goes offilne.
Fabrice

Error message when syncing CUACEE 9.0.1.2 with CUCM 9.1.1

Hi all,
When I set up the CTI template, I chose owner userid as "none" but then when syncing the AC, I get the message on the sync report for every device of "Error -206 The specified table (owneruserid) is not in the database."
If I set the template to use a specific owner userid and resync, then it works correctly, but I don't want these CTI ports associated with a userid.
Is there any reason why this would be happening, as I have been able to do it in the past with "none" on 8.6

Sean,
Yes, this is a known defect: CSCue69477 - CTI Route Port Synch Issue with CUCM. As per the bug:
"This issue will occur if the "SUBSCRIBE Calling Search Space" under Protocol Specific Information in the Template for the CTI Route Ports is configured. To work around this, the "Owner User ID" under Device Information for the Template needs to be configured."
Regards,
Jason

Is Unity 7.0(2) compatible with CUCM 8.6 ?

Is Unity 7.0(2) compatible with CUCM 8.6 ?
The documentation reports the compatibility with CUCM 8.5(x), but is not updated for 8.6.
Thank you

The documentation related to 8.6 may lag behind for a bit. However, if you are running or update to the latest TSP (8.4.3) on your Unity server then you're likely covered. The version of TSP is really the only compatibility factor as far as Unity/CUCM is concerned.
Hailey
Please rate helpful posts!

CUCI-Lync 9.2 with CUCM 8.6 - Cisco Unity Connection Visual Voicemail Not Working

Hi
I have CUCM and CUC 8.6.2 running and MOC with CUCI-Lync 8.5 (with visual Voicemail) running OK with full registry configuration (see below). We are moving to Lync 2013 and want to use CUCI-Lync 9.2.
A basic install of CUCI-Lync 9.2 works fine with CUCM (with manual setup of TFTP, CCMIP and CTI) but not with CUC. I can only call the VM Pilot but I don't get my visual voicemail. In the CUCI-Lync parameters I type in my CUC server IP adress and credentials but get a message saying that it can't connect.
As the config guide describes a config with CUCM 9 (with UC services) which I don't have in V8.6. I've tried using the old registry configuration or no registry configuration at all, I can't get CUCI-Lync to connect to CUC...
Has anyone done this ? Any suggestions ?
OLD REG Configuration:
Windows Registry Editor Version 5.00
[HKEY_CURRENT_USER\Software\Cisco Systems, Inc.\Unified Communications\CUCIMOC]
"RememberMe"=dword:00000001
"AutoLogin"=dword:00000001
[HKEY_CURRENT_USER\Software\Cisco Systems, Inc.\Client Services Framework\AdminData]
"TftpServer1"="1.1.1.1"
"TftpServer2"="2.2.2.2"
"TftpServer3"=""
"UseCUCMGroupForCti"="1"
"CcmcipServer1"="1.1.1.1"
"CcmcipServer2"="2.2.2.2"
"CcmcipServerValidation"="0"
"CsfStatsServer"=""
"CsfStatsCollectionEnabled"=""
"EnableNativeDirectoryProvider"="1"
"VoicemailPilotNumber"="12345"
"VoiceMailService_UseCredentialsFrom"="PHONE"
"VVM_SystemServer_0"="3.3.3.3"
"VVM_SystemServer_1"="4.4.4.4"
"VVM_SystemServer_VmwsProtocol_0"="HTTP"
"VVM_SystemServer_VmwsProtocol_1"="HTTP"
"VVM_SystemServer_VmwsPort_0"="80"
"VVM_SystemServer_VmwsPort_1"="80"
"VVM_Mailstore_Server_0"="3.3.3.3"
"VVM_Mailstore_Server_1"="4.4.4.4"
"VVM_Mailstore_ImapProtocol_0"=""
"VVM_Mailstore_ImapProtocol_1"=""
"VVM_Mailstore_ImapPort_0"="143"
"VVM_Mailstore_ImapPort_1"="143"
"VVM_Mailstore_InboxFolderName"=""
"VVM_Mailstore_EncryptedConnection"=""
"VVM_Mailstore_PollingInterval"=""
"AutomaticDeviceSelectionMode"="0"
"SSO_Enabled_CUCM"="false"
"DeviceProviderServer1"="1.1.1.1"
"DeviceProviderServer2"="2.2.2.2"
"DeviceProviderServerValidation"="0"
"DeviceProviderType"="CCMIP"

The UC Services are a CUCM 9.0 feature. In 8.x these existed within CUPS under Applications > CUPC/Jabber > CTI Gateway and Profile. Other things that frequently cause this to break: 1) deskphone not associated to your end user object; 2) primary extension not set; 3) standard cti enabled and standard ccm end users group membership missing; 4) the IP/FQDN of the CTI Gateway is not a CUCM node running CTI Manager.
Please remember to rate helpful responses and identify helpful or correct answers.

CU MeetingPlace Express 2.1.1.2 Compatibility with CUCM 7.1+

Afternoon all,
According to Cisco's compatibilty matrix, Cisco Unified Meeting Place Express version 2.1.1.2 is only compatbile up to CUCM 7.0.
I understand that CUMPE 2.1.1.2 is coming to end of sale life. However, if it currently works with CUCM 7.0, then surely it will work with later releases of CUCM up to 7.1(3)?
I appreciate Cisco might not support it if there is a problem, but was hoping someone else was running MPE 2.1.1.2 with CUCM 7.1(3b)
Thanks
Jamie

Hi Jamie,
The Compatibility Tool does show support for MPE 2.1.1 with CUCM 7.1 (x)
Cisco Unified Communications Compatibility Tool
http://tools.cisco.com/ITDIT/vtgsca/VTGServlet
Here are 3 groups running this similar combo;
https://supportforums.cisco.com/message/3145002#3145002
https://supportforums.cisco.com/message/1330041#1330041
https://supportforums.cisco.com/message/3150066#3150066
Cheers!
Rob

LDAP Synchronisation with CUCM with multiple forest

Hello,
We have CUCM 10.5.
We want to add in CUCM multiple forest (we have multiple company with different domain name) using LDAP authentification so all the user/password sync with CUCM.
We have as distinguished name CN=xxxx,CN=Users,DC=xxx,DC=local and for search base CN=xxxx,CN=Users,DC=xxx,DC=local.
Can we add in the distinguished name and search base the information for multiple forest using the same username/password?
If it not possible is there an easy way to achieve that?
Any help would be appreciate.
Thank you

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/collab10/collab10/directry.html#pgfId-1133454

Unity 7 with cucm 8

Hi all experts.
Is unity 7 with domino supported with cucm 8 ?
I checked the following link and it seemed confusing
http://tools.cisco.com/ITDIT/vtgsca/VTGServlet
Kindly confirm

Hello -
I think this is a more clear document - http://www.cisco.com/en/US/docs/voice_ip_comm/unity/compatibility/matrix/cutspmtx.html
At minimum, you may just need to update the Unity TSP (AVSkinnyTSP) to match it with CUCM - this is most often recommended to help with MWI issues.
Sincerely,
Ginger

Is Presence 7.0 compatible with CUCM 8.0

Is Presence Server 7.0 compatible with CUCM 8.0 or do I have to upgrade my presence server to 8 also ?

CUPS 7.x is not supported with Call Manager 8.0.
Pierre.

SCCP FXS on 2911 with CUCM 10.X

Similar Messages

Maybe you are looking for