SCFILTER\CID_c80d Driver (Smart card Reader)

I can´t install the driver SCFILTER\CID_c80d Driver (Smart card Reader) for my zbook17. Where can I find the driver?
Thanks

Hi
Try Alcor Micro Smart Card or Realtek PCIe Media Card Reader Driver

Similar Messages

What kind of driver do I need to use for HP Elitebook 8440p RICOH Smart Card Reader?

I'm using Arch linux x86_64 and need to install Smart Card Reader, but I can't find any drivers for it.
Best regards,
Taavi

What operating system is it? Are you sure you put the card in the correct way? [not trying to be mean here]

MS Remote Desktop and smart card reader

I have installed MS Remote Desktop Conn. on my iMac and connected a smart card reader via the USB. Although my reader energizes when the computer is on, the computer doesn't seem to recognize the reader. When I insert a CAC card into the reader and try to log in remotely, I continue to get a "username/password" box instead of the CAC PIN number. Do I need to install some kind of smart card driver or does Apple already have it? I'm at a loss as to how to fix this.

I was able to get rdesktop 1.6.0 to install on my Mac and I was able to get CAC log-in to work.
However, the installation is a little tricky. I downloaded rdesktop 1.6.0 from this link:
<<http://www.rdesktop.org>>
My instructions for installation:
1. Make sure Xcode Tools is installed on your computer. It should be on your OS X install disk.
2. Find out where your X11 libraries are located:
-From the Finder menu, selct "Go" >> "Go to Folder..."
-Type (without the quotes) "/usr/X11", and click "Go"
You should see a bunch of folders. Make sure the "include" and "lib" folders are there. Otherwise you need to find out where the X11 "include" and "lib" folders are located on your computer.
3. Download rdesktop and place the (unarchived) rdesktop-1.6.0 folder on your Desktop
4. Open the X11 application (should be in your Utilities folder)
5. In the X11 window type the following (without the quotes):
"cd Desktop/rdesktop-1.6.0 && ./configure --enable-smartcard -x-includes=/usr/X11/include -x-libraries=/usr/X11/lib && make && sudo make install"
4. Hit enter. When prompted, enter your administrator password and hit enter.
rdesktop should now be installed in the following folder:
/usr/local/bin
So, to launch rdesktop with smartcard log in enabled, open the X11 application (or Terminal application) and type the following (without the quotes, and replace your.server.address with the server address):
"cd /usr/local/bin && ./rdesktop -r scard your.server.address"
Hit enter and it should launch a new X11 window that will try to access the remote server where you should be prompted for your PIN.
To explore more options with rdesktop, open X11 and type the following (without quotes):
"cd /usr/local/bin && ./rdesktop"
Hit enter and you should get a list of options available to rdesktop.

ACR122U smart card reader not recognized after reboot...

I am new to POS Windows and have been working with wondows for ever. I was using ACR 122u contactless usb smart card reader with windows XP and communicating with it using java with no problems. Then our I changed the OS to windows Pos ready 2009 and we found out that USB card reader has to be unplugged and plugged back in after rebooting the computer. other than the OS everything else is identicle (driver, reader, java program, ect..). Can any one tell me what could cause this problem and what I can do to solve this.
I have cheked the device manager and under USB controllers it says that it is unrecognized deivice..I tried changing the reader, changing the port and(actually the reader is pluged in to a linksys external usb hub, but changing this to a internal port did not make any difference) tried chagning some settings in control panel.
1. I checked the power option of the root usb hub.
2. Changed the driver.cab to a normal driver.cab obtained from the normal xp version. Uninstall the driver and reinstall it.
So far this hasnt been working.
I hope someone could help me with this.
~Tharanga

After extensive tests with Win 7 Embedded and ACR122U, I can confirm the same problem. It seems that reader firmware hangs and the only way to recover is to unplug and plug again the reader. We shall repeat the tests with readers from other manufacturers.
For the tests, we use a Win7 Embedded Standard PC with an ACR122U connected. We installed and configured the ACS Monitor program to start automatically with windows. We made a small utility to restart the PC every minute and we placed it on the Startup directory.
Within the first 5-10 reboots, the reader fails and the ACS monitor program shows " No reader connected" and no reaction from the reader. If we shall unplug and plug the reader again to the USB port everything works fine again.
Kostas P.

Use of CAC enabled sites (Smart Card Reader)

Would anyone happen to know if the PlayBook would support the use of the BlackBerry Smart Card Reader 2?
I would love to be able to access my DoD sites that require my CAC login using the BlackBerry Sled and my PlayBook. Thank you for any assistance in this matter.
BB-Soldier

Ditto!!!
I have a SCR331 and I am not able to get 10.5 to recognize my CAC card.
I do believe Leopard is recognizing and using the SCR331 but the problem
lies in the CAC Card Driver. Here are the details :
Hardware : SCR331 USB with firmware 5.22
CAC Card : Oberthur ID One v5.2
System log when CAC card is inserted into 10.5:
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:21:26 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/ifdhandler.c (554): GCCmdCardStatus failed
Nov 9 06:21:26 angel com.apple.SecurityServer[20]: src/CCIDDriver/USB/MacOSX/usbserial_mosx.c (974): ERR: Couldn't close device (e00002c0)
I hope Apple developers manage to fix this in put it in 10.5.1.
Thanks,
Mike Bender
Orlando, FL

Smart Card Reader

Bought my T410 (2516 CTO) running on Win 7 Pro 32 a year ago, with an integrated Smart Card Reader which should read several types (¿?) besides the SD that already recognizes perfectly.
Trouble is I can't find anywhere which are those other Memory types. Read here and there, the whole FAQs, searched for it and it seems there isn't any clue regarding this issue.
Can someone please tell me which other Memory Cards does it read?, besides SD I already checked.
I had the hope it could read a XD Card, because it fits naturally, but it doesn't.
(The driver is updated to the latest just in case anyone might comment on this issue).

hello Tweedle,
the BlackBerry 10.1 OS will be compatible with the BlackBerry Smart Card Reader 2.0.
Check the announcement :
http://supportforums.blackberry.com/t5/Announcements/Announcing-BlackBerry-10-1-OS/m-p/2345427
The search box on top-right of this page is your true friend, and the public Knowledge Base too:

Smart Card Reader on Leopard

Has anyone tried to use a Smart Card reader and CAC with Leopard? It worked flawlessly with Tiger, but Leopard doesn't even recognize the reader is attached. I can run Parallels with XP and it immediately recognizes it works with all sites, so I know the reader is good and the USB bus is ok.
Any help is greatly appreciated.

Ditto!!!
I have a SCR331 and I am not able to get 10.5 to recognize my CAC card.
I do believe Leopard is recognizing and using the SCR331 but the problem
lies in the CAC Card Driver. Here are the details :
Hardware : SCR331 USB with firmware 5.22
CAC Card : Oberthur ID One v5.2
System log when CAC card is inserted into 10.5:
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:09 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (793): Protocol type of card (T=1) not supported by this driver for this type of reader (TPDU)
Nov 9 06:16:10 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/CCID.c (795): An APDU-level reader should be used
Nov 9 06:21:26 angel com.apple.SecurityServer[20]: src/CCIDDriver/common/ifdhandler.c (554): GCCmdCardStatus failed
Nov 9 06:21:26 angel com.apple.SecurityServer[20]: src/CCIDDriver/USB/MacOSX/usbserial_mosx.c (974): ERR: Couldn't close device (e00002c0)
I hope Apple developers manage to fix this in put it in 10.5.1.
Thanks,
Mike Bender
Orlando, FL

Why does a smart card reader kill MacOS?

I need a smart card within a virtual machine on my Mac. The trouble is, every time I connect the reader, my MacOS stops working properly.
When the smart card reader is connected before the Mac is turned on, then I can't login: After entering the password, it hangs with the spinning color icon.
I can boot without the reader, though. If the reader is plugged in after boot, this happens:
Safari doesn't start up, all I see is the color spinner. Finder gets blocked as well while Safari is trying to start up (i.e. forever)
If I have a Terminal open, then I can "kill -9" the Safari process, which unblocks the Finder.
When I then try to shut down, it hangs with a white screen, and never properly finishes until power off.
How can I debug or solve this problem?
Thanks! Martin

It's a very common device (Omnikey 3121), which should be compatible. Nevertheless, I installed drivers from the manufactor's site to see if they make any difference. On reboot after driver installation I got a kernel panic within the HID drivers. Very strange.
Kernel Extensions in backtrace:
com.apple.iokit.IOHIDFamily(2.0)[994495B5-FB34-3DB5-B47A-D2A732E52F33]@0xffffff 7f811c1000->0xffffff7f81232fff
dependency: com.apple.driver.AppleFDEKeyStore(28.30)[2A8A5F6B-0A7C-33A0-8E5B-4C10F646EC4F]@ 0xffffff7f811b6000
After reboot it seems to work fine, but I'll have to check some more.

T430s Smart Card reader cannot read some cards

Hi all,
I have a T430s with a smart card reader.
Turns out that some cards (including, as it happens, one of my personal cards) the reader can't read. It either does not respond at all, or gives an "unknown card" identification. The very same card, on the very same laptop, using an Athena USB reader, works flawlessly.
I'd say it's a reader malfunction BUT some other cards are read perfectly by my built-in reader... Why would the reader refuse to read certain cards?
Any ideas? Anyone seen something like this?
Thanks for any insight!

Hey 127kmph,
If the driver for the media card reader doesn't work,
I found your computer in the personal system reference and saw you actually have no Smartcard reader. But you do have the 4-1 media card reader. Which is specific to all machine types of the T430s.
With a little more investigating I found out that
You have a Ricoh Multi Card Reader on the computer. This reader is able to read SDHC cards, but to get it to work fully you have to update the driver.
Here is the link to the driver. Which this driver supports XP, Vista, and Windows 7.
http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014960
Thank you NINE.
Hope this works out for you
Please let us know,
Alex
Was this or another post on the forum helpful? Click the star on the left side of the screen to give kudos! Did someone solve the problem you encountered? Click Solution Provided to let us know!
What we Do in Life will Echo through Eternity. -Maximus Aurelius

Does Java Card require a USB CCID-compliant smart card reader?

Hi experts,
Does Java Card require a USB CCID-compliant smart card reader? I'm currently working with PC/SC usb token and it requires usb CCID-compliant smart card reader, which seems very inconvenient for my clients and I'm wondering if Java Card has the same issue? (I'm thinking about switching the project to Java Card)
Any help will be much appreciated!
Z.Zen

Hi,
You will still need to install drivers for some card readers to function correctly. I know some work out of the box on Windows and OS X (10.5+ at least) ships with the pcsclite CCID driver from the Muscle card project. When I view my reader in Windows device manager the Manufacturer is "USB CCID Compliant".
The only real difference between what you are doing with the USB CCID token and Java Card is that the card and reader are separate in the Java Card option where as the USB token has the reader and chip in one package.
Cheers,
Shane

Broadcom USB Smart Card reader not working

After upgrading my Vista Business SP2 (32-bit) to Windows 7 Ultimate RC (32-bit) my Broadcom USB smart card reader does not work any longer (Dell Latitude E6400 with built in smart card reader).
The newest available driver from dell support was already tested (Broadcom, driver date 09/23/2008, version 1.0.0.1, digitally signed WHQL, released by dell in March 09), but the device can not start (Error code 10) with Windows 7.
With the Microsoft WUDF Driver (Usbccid, driver date 06/21/2006, version 6.1.7100.0) the device starts but whenever I insert my smart card an additional device is detected (other device - smart card) but no driver found - Error message is: The drivers for this device are not installed. (Code 28).
What else can I try to get this reader working again (with vista sp2 the smart card reader was working fine with the broadcom driver)?

I have also an USB card reader that works fine on XP PCs but Win7 does not recognise it, can msft make a sd reader driver that works pls.
Hi
Sorry, but the way the industry works is that Microsoft develops Windows and Hardware manufacturers develop drivers for their products. Microsoft does maintain a complete division (MSDN) that is dedicated to assisting hardware and software manufacturers in developing their products for compatibility with Windows.
All of the drivers that are contained on the Windows installation disk and on Windows Update are placed there by the manufacturers of the devices. This is a service that Microsoft provides to help these manufacturers to distribute their drivers.
What you can do.
1. Check with the computer manufacturer for updated drivers for that device. This is your best source, since the computer manufacturer builds, tests, and sometimes develops their own, custom drivers to work with the hardware on their PCs.
2. Try to determine the name and manufacturer of the device using Device Manager and MSInfo32. Once this information is found, try to find that manufacturers website and look for the latest compatible drivers.
3. Check to see if there are any users forums on the PC manufacturers or device manufacturers websites. Ask there about any known issues with this particular hardware device or if the device is no longer supported.
4. If the drivers are found but are only available for previous versions of Windows, install the drivers using the Windows Compatibility Mode. HOW TO: Install a Hardware Device Driver using Compatibility Mode
Right now, we are in a unique situation since we are using an operating system that is still in the pre-release phase. Many hardware/software manufacturers will be ofrficially supporting their products for Windows 7 until after the General Availability date of October 22, 2009.
Hope this helps.
Thank You for using Windows 7
Ronnie Vernon MVP

Install mSATA drive in card reader slot of M92P small form factor

I thought it would be a wonderful idea to install a SSD in my M92P SFF. Seems I can't do that unless I ditch my installed hard drive as there is no second drive slot. So now I'm left with the option of installing an mSATA drive. The manual says I need a "storage converter" with a mini PCI Express slot.. Where, oh where, do I get one of these 'cause it certainly did not come installed on my machine? Anybody have experience installing one of these puppies? Thanks in advance.

After doing some research on the message, I came across this post.
Apparently, your PC has a smart card optional system (maybe it was government surplus).
http://h30499.www3.hp.com/t5/Business-PCs-Compaq-Elite-Pro/DC7800-smart-card-athentication/m-p/10691...
Now, if you can get into the BIOS menus, if you look at the top of page 8, you will see what you need to do in order to enable/disable the smart card reader message.
http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01162201/c01162201.pdf
Whatever the problem is, it is a security setting issue, and clearing the CMOS or updating the BIOS will not have any effect on that setting.
Unfortunately, I have no experience with the security settings or protect tools software on HP business PC's.
I have a dc7800 (and only use HP business desktops and notebooks), so I am very familiar with all the other aspects of the PC, but that one.
You may want to post your issue on the HP business support forum, business PC section. Hopefully someone there has experience with turning this feature on or off.
http://h30499.www3.hp.com/t5/Business-PCs-Compaq-Elite-Pro/bd-p/bsc-271#.Uk2rcJAo69I
You may also want to log in and reply to that post, but don't get your hopes up that it will be answered.
RichS hasn't replied to a post in 3 years. Although someone else may.
Good luck, and please post back if you find the solution to the problem.

W520 Smart Card reader does not show up in Device Manager

W520 Smart Card reader does not show up in Device Manager.
It was working before and now nothing. Nothing happens when SD card plugges in.
Could my smart card reader stop working or is this a configuration issue?
Any thoughts?
thanks
Ian

Hi Ian,
Welcome to the community, and thanks for the post.
The issue is related with software, to resolve this you need to re-install the card reader driver from the below mentioned web link.
http://support.lenovo.com/en_SG/downloads/default.page?
After that check if the issue get resolved.
Regards,
Sameer
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Acrobat 9 does not recognize the smart card reader that work with other app. Can someone help me?

Hi to All,
Acrobat 9 (included in CS4 design premium) does not recognize the smart card reader. I have a smart card reader ACR38 smart card that works with all applications except Acrobat 9 pro. I tried to uninstall and reinstall it again, but when I try to insert the digital signature message is always the same, that does not find the Acrobat reader. Can someone help me?

Hi MartinR
Thank you for your reply, i have tried what you suggest, and it did not work, the i DVD opening title changed but not the embedded movie.
Perhaps it is a setting in Final Cut Express?
After capturing my footage, i open a new project then i convert all clips to anamorphic, to give me the letterbox effect, i have tried now with and without anamorphic.
In my canvas screen, the footage does not fill the square, even if i have not selected anamorphic, and fall well within the TV safe areas, but the only way to ill the canvas up is to crop it bigger, but still when i export it does not give me the full screen view.
Any ideas?

How to install a smart card reader.

I am trying to install a smart card reader for work. There are no prompts when connecting via USB or anything else.

There shouldn't be a prompt when you connect an empty card reader. Insert a memory card into it and it should appear on the Desktop.

SCFILTER\CID_c80d Driver (Smart card Reader)

Similar Messages

Maybe you are looking for