School network uses WEP with 802.1x  Encryption How do I connect?

My University uses WEP with IEEE 802.1x Encryption with Protected EAP. There are two wireless networks I can connect to and they both use the same security settings. In order to connect on my laptop, I have to enter an User name and Password. I have to use the same user name and password to log on with my iPod touch. The problem is that while both school networks show up on my touch, I can not connect to either because I am only prompted for a password when I need to enter both a user name and password. As far as I can tell, this is not possible on my touch.
Is there a correct way to do this? Is this feature even supported by the iPod touch? Any help would be greatly appreciated.
Thank you

Followed your links and did some searching on the website.
found this page: http://www.calumet.purdue.edu/ctis/wireless_drop.html
And I think this might be the problem:
"How Wireless Access Works
Wireless access points emanate radio signals in a similar manner to non-cellular cordless phones. The signals are strong enough to be received up to 50 to 100 feet from each access point (and possibly further, if the access point is equipped with an external antenna). These signals can be received by laptops and PDA's that are equipped with a standard 802.11b/g wireless card. This feature can be requested when ordering a new laptop computer, or an 802.11b/g card can be purchased and added to most older laptops. _Please note that the iPhone, iTouch, and any device with a palm OS is not compatible with the wireless network_."

Similar Messages

  • HP Officejet Pro 8500A Plus Support WEP with 802.1X

    My boss currently bought a HP Officejet Pro 8500A Plus that have wireless function. Unfortunately our corporate wireless is protected with WEP with 802.1X that requires certificate import into laptop to connect to the wireless. I run thru the whole HP Officejet Pro 8500A Plus do not have any instruction on import the cert. I depply appreciate if any experts can assist me on the wireless setup?

    Hello-
    Make sure printer firmware is up to date.
    http://www.youtube.com/watch?v=qZBhl0eMBPs
    Also, plug printer directly into wall outlet.
    Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
    Please select the "Accept as Solution" button on the post that best answers your question.
    I appreciate your input !
    Thank You,
    Donald

  • I have 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II.  How do I connect?  4000 only has 1 Display Port and 1 DVI.  5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute?

    I just bought a 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II.  How do I connect?  4000 only has 1 Display Port and 1 DVI.  5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute any work at all?  I read where on a PC they would work together, but on a MAC they do not.
    I read that Display Port has higher band width than DVI, NEC monitors for best performance they recommend using DIsplay Port.
    When I was setting this up I looked at a Nvidia Quadro 4000, unfortunately it was for PC, it had 2 Display Ports, in the Mac version they reduce it to one.  I did not think there could be a difference.
    Mainly want to use it for CS6 and LR4.
    How to proceed??? 
    I do not want to use the Quadro 4000 for both, that would not optimize both monitors, one DP and 1 DVI.  Using just the 5770 would work but I do not think the 4000 would be doing anything, and the 5770 has been replaced by the 5870.more bandwidth.
    Any ideas, I am a Mac newbie, have not ever tried a Mac Pro, just bought off ebay and now I have these problems.
    As a last resort I could sell both and get a 5870.  That would work, I'm sure of that, it's just that I wanted the better graphics card.
    Thanks,
    Bill

    The Hatter,
    I am a novice at Mac so I read all I can.  From what I understand the NEC monitors I bought require Display Port for their maximum performance.  The GTX 680 only has DVI outputs.  Difference from what I understand is larger bandwidth with the DP.
    You said I have the 4000 for CUDA.  I am not all that familiar with CUDA and when I do read about it I do not understand it. 
    A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000.  Is the 4000 doing anything with nothing connected?  I read where in a PC system the 2 cards would interact but in a Mac system they do not.
    Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
    So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
    I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are.  I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4.  Those NEC monitors are supposed to be top notch.

  • I can't upload iTunes 11.1 to my iMac I also can't upgrade OS X when I try both it say can not download to this computer with no explanation so how do I connect my iPhones to iTunes

    I can't upload iTunes 11.1 to my iMac I also can't upgrade OS X when I try both it say can not download to this computer with no explanation so how do I connect my iPhones to iTunes

    Oneflesh6511 wrote:
    If I buy more iCloud space and back up my phones to that will I still be able to get everything from my iTunes on my phones that way?
    Backing up your phone isn't really relevant. You can download items you've already purchased (from the iTunes Store on your Mac) to your phone. If you have items you didn't purchase, e.g. ripped CDs, you would have to subscribe to 'iTunes Match' ($24.99 p.a.) to be able to do the same thing with them.

  • Not able to connect to wireless network using WEP 128 bit hex password

    I'm using a 128 bit hex WEP password on a Belkin wireless router.
    My ascii passphrase is 13 characters.
    I tried using the hex password generated by the Belkin router, as well as the hex equivalent of my ascii passphrase. Every time, I am told that either "there was an error connecting to the network" or the "password is incorrect" message.
    I'm using channel 7, but have also tried with channel 11.
    I tried using a $ sign in front of the WEP hex password. The $ does not work with Open Internet Connect or the Airport menubar.
    I can connect if I don't use any encryption on the wireless network, and also through the Ethernet cable.
    I have an iBook which connects fine to the wireless network.
    So why doesn't the iMac work the same way ?

    The security difference between NO encryption and any form of WEP is about 2 minutes or less for somebody looking to get in... besides having WEP enabled makes you look like an easy target since you think it'll stop anything!
    Either leave it off, making Hackers think at least 3 minutes about WHY, or use/setup WPA of one form or another!

  • AAA using Radius with 802.1x

    Hello there,
    We're going to be implementing 802.1x on our network of some reaallly old switches (6509 Cat OS with MSFC 2).  We use radius for AAA authentication and I've been reading that .1x uses radius.  How is that going to work?  Do I just add another radius server in my radius server command and, more importantly, will .1x work on Cat OS running 8.2.1?  I've been trowling the forums and I can't seem to find anyone who's actually running .1x on the old Cat OS switches to see what kind of gotchas I can expect to run into.
    Any advise, assistance would be greatly appreciated!
    Thanks
    Kiley

    Salodh,
    Thanks but that document is for a 2950 and we have a 6509 but, the good thing is I just found out our Tier 3 engineers will not be adding dot1x to the 6509 since it has only trunks - no access ports.  Thanks very much for your reply!

  • Is it best to extend a Wifi network using Airport Extreme 802.11ac or Express ?

    I previously asked this question with a different emphasis here:
       https://discussions.apple.com/message/24347878#24347878
    so have re-worded to be more relevant to the subject.
    I have a brand new Airport Extreme 802.11ac which I am now using as my network hub and I would like to extend the network wirelessly.
    Is there a benefit to extending the network via another Airport Extreme 802.11ac versus a (cheaper) Airport Express ?
    I do not have any 802.11ac clients yet, but likely will do within the expected lifespan of the routers and thus would rather buy another Extreme now if it meant extending the best signal strength.
    Per my previous post i would ideally extend using my old Edimax BR-6675nD 450Mbps 2.4GHz/5GHz, however this has been problematic and some previous posts imply that mixing Apple and non-Apple routers is not recommended, if this is not correct please do let me know.
    Thanks in advance.

    Is there a benefit to extending the network via another Airport Extreme 802.11ac versus a (cheaper) Airport Express ?
    Four possible benefits, which may or may not be benefits to you:
    1) A second Extreme will extend the faster "ac" speeds of the main AirPort Extreme, while the Express will not.
    2) A second Extreme uses Gigabit Ethernet ports....ten times faster than the Express....if you plan to connect devices using an Ethernet connection
    3) The USB port on the AirPort Extreme will accept a hard drive while the Express will not
    4) The AirPort Extreme has a much better antenna arrangement than the Express, which will provide greater coverage even if "ac" wireless is not used
    On the other hand, if you do not need "ac" wireless to be extended, you only plan to use the Express to extend the wireless, and the Express will be located where it can receive a strong wireless signal, then you might save a bit of money going with an AirPort Express.
    So, in questions about what would be "best", there are rarely simple answers that apply to all users. The question really is which is "best" for you. Adding another AirPort Extreme would be a no brainer for me, but perhaps not for you.
    i would ideally extend using my old Edimax BR-6675nD 450Mbps 2.4GHz/5GHz, however this has been problematic and some previous posts imply that mixing Apple and non-Apple routers is not recommended
    It is always the best idea to use products from the same manufactuer for the same purpose throughout the network. Obviously, an Apple AirPort Extreme will be compatible with another AirPort, while a third party device may or may not be.

  • Furthur Understanding of using WEP with TKIP, MIC, PPK, and BKR

    While implementing The Cisco Wireless Security Suite across an 802.11b (2 350 Bridges)link, I have to ask a question.
    I used to use 4 X 128 bit keys for just the WEP part (WEP screen has 4 places to set the keys).
    On the Radio>advanced Screen, you have the place to set your MIC and your Per Packet Keying...understanding that Per-Packet Keying assigns a new WEP key to each frame, is it necessary to Set 4 WEP keys on the WEP key screen?? Or should I set just one? Do I have to set any with PPK enabled on the Radio>advanced screen? Or is this done dynamically by the bridges??
    It does not seem like I should have 4 WEP keys set on the WEP key screen if I have selected Per Packet Keying on the Radio>Advanced Screen? Is this accurate??

    Yes you are accurate, you can select which key you want to use by clicking Transmit Key.

  • I have a new MBRP. On wired ethernet it can be used as a wireless hotspot. Since 802.11ac gets better range I'd like to use it with 802.11ac as a hotspot for my older 802.11g/ndevices. Can I do that ?

    I know that if I use wired ethernet then the  MBRP can be a wirelss hotspot for other devices. Since the MBRP supports 802.11ac and I have a new 802.11ac wireless router it gets much better range than my older 802.11/n devices.  There are places in teh house where the MBRP connects to the wireless but where older 802.11g/n devices lare out of range. In those rooms I'd like to use my MBRP connected to the network wirelessly using 802.11ac as a hotspot for the nearby 802.11 g/n devices. Anyone know if that can be done and how to do it ?

    Turn on Internet Sharing in Sharing preferences. Share the Ethernet connection to wireless.

  • I would like to replace my old AE 802.11g with new version 802./11n - How do I connect

    I have just bought a new Airport Express (802.11n wi-fi)  and would like to use it as the base station in place of the older version (802.11g).
    The old one to be used in another room connecting to my sound sytem as an extention to the new one.
    Both of these AEs  utilise different Aiport Utility (5.6 against 6.1).
    Can anyone please give me some detailed explanations of  how I can set-up these devices, if indeed they are possible.
    Alan

    Sorry, just to make sure: Do you want the older 802.11g Express just for iTunes streaming or (in addition) to extend the wireless range of the newer 802.11n Express? If it is the latter, you may want to reconsider doing so as the only way to extend with "mixed" base stations is with a Wireless Distribution System (WDS).
    A WDS has two major disadvantages: 1) It can only operate in the 802.11g radio mode, basically negating the advantage of your 802.11n Express, and 2) For every base station added to the WDS, the overall bandwidth is cut in half. So starting with 54 Mbps (for 802.11g), your extended wireless network will be running around 25-27 Mbps.

  • How do I use an used iphone with an exsisting AT, How do I use an used iphone with an exsisting AT

    How do I set up an used iphone to an exsisting AT&T account

    Set it up as new by going to Settings>General>Reset>Erase All Content and Settings (which returns it to it's new out of the box condition), put your SIM in it and go through the activation screens.  Be sure this is an AT&T phone though as AT&T phones are locked to only work on the AT&T network.

  • I can't seem to see sync my mac and iphone using iCloud with numbers and pages how can i correct this?

    Hi
    I've used Numbers and Pages for IOS for sometime now and when i use safari to look at my icloud account i can see all my files. Recently i bought Numbers for Mac and now whenever i create a spreadsheet on my mac i can't see it on my iphone but i can if i login to icloud. In fact i can only see about 16 files on my iphone when there is over 40 files.
    Although i don't yet have pages for mac i now have a similar problem with Pages, whenever i edit a file or even create a file on IOS it doesn't appear in icloud.
    I did think it was something to do with me not selecting backup to icloud so i then spent £14 to upgrade my storage to 15GB and that hasn't helped.
    I've checked all the settings and can't see anythng that will cause the problem.
    My iphone is running IOS 6 and my Mac is running Mountain Lion 10.8.2
    Does anyone know how to correct this mess?
    Many thanks in advance.
    Mick.

    Problems with buttons and links at the top of the page not working can be caused by an extension like the Yahoo! Toolbar or a Babylon extension that extents too much downwards and covers the top part of the browser window and thus makes links and buttons in that part of the screen not clickable.
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
    *Do not click the Reset button on the Safe mode start window or otherwise make changes.
    *https://support.mozilla.org/kb/Safe+Mode

  • My Eye Dropper STILL does not work in CS5 while using Lion with one monitor. How can i fix this?!?

    Hello everyone!
    This is my first post because i have grown very disgruntled at the fact that my eye dropper does not work my Premiere CS5. I would use the Ultra Key a lot but now I obviously can not really use it too well because of no eye dropper. I saw that this problem existed after the Lion update but this really should have been fixed by now. I am using only one monitor also. Is there a way to fix this or is this still known to be broken? I paid good money for CS5 and would be very upset if the only way around this is to pay MORE money to upgrade to CS5.5. Thanks.

    Thanks for the response Stephen! I find this very bad on Adobe's part though if they do not feel obligated to fix CS5 for Lion. Eye dropper is a major part of Premiere and i am going to be very dissapointed if they do not fix that. With the amount of money the Suite costs, they definitly should make sure it runs well for quite a few years. I would expect a copy of CS4 to be able to work too. If they do not fix CS5 all because the OS has changed basically tells me that every 2 years or so, they stop caring about their product.
    Sorry i sound so bitter about this but it has really hurt my workflow. Ultra key is great and something that FCP does not have so it has the edge in that respect, but now i can not even properly use it. I have to go into After Effects with the same clip, use that eyedropper to get the correct color # and then copy and paste the # into Ultra Key in Premiere which is very very annoying and slows down my system quite a bit.
    So basically, they are probably not going to ever fix this? Thanks again

  • I just bought an ipad 3.  The hotel I am staying at only has basic internet using a cable not wifi.  How can I connect with my ipad?

    I am staying at a hotel that using traditional internet with a cable.  Not Wifi.  Can I connect my ipad to their cable?

    No.
    For future consideration if this is something you will be doing on a regular basis, you need to bring your own wireless router along.
    http://store.apple.com/us/product/MB321LL/A/AirPort-Express-AirTunes?fnode=MTY1N DA0Mg
    http://itunes.apple.com/us/app/airport-utility/id427276530?mt=8

  • Want to use dotNet with teststand, but unsure how to send commands through serial port

    I have a loCom communication dll used to send and recieve commands through serial comunication for a particular product.  I the past they have used a LabVIEW wrapper to send and recieve commands, using this particular dll.  I would like to just use testStand for the DOTNET Dll.  I can get the commands, know the inputs and outputs required, however I can not figure out how to send the commands to the serial port.  Anyone have any exprience doing this in TesSTand?

    hallawt,
    With your .NET code module, you should be able to call it directly, most likely as a parameter in the .NET method.
    What are the inputs for the method you're trying to use?
    Also, could you clarify where you're starting to have problems in your project?
    Regards,
    Renée M
    Applications Engineer
    National Instruments

Maybe you are looking for