SCOM 2012 UCS Management Pack Configuration/Administrator Guide

Hi,
We are planning to use SCOm 2012 for UCS Monitoring and Reporting purpose. Is there any detail configuration/Administrator Guide available?
Is there any best practice document availble to monitor critical ports( Network uplink/Storagre Uplink) ports and and setting up threshold limit?
Thanks in adavance for your help..

Hi Hetal,
Please take a look at this guide for starters:
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/msft_tools/scom/scom_2.6/scom_2.6_user_guide/scom_2_6_monitoring.html
Thanks,
-Bruce

Similar Messages

SCOM 2012 R2 Management Pack for Fortinet

Is there any management pack to monitor fortinet for scom 2012 R2

Hi Syed,
As well, you can try to monitor your Fortinet with SNMP traps:
http://stefanroth.net/2014/04/07/scom-2012-snmp-traps-how-the-heck-do-i-get-it-working/
http://docs-legacy.fortinet.com/cb/html/index.html#page/FOS_Cookbook/Install_advanced/snmp_setup.html
Natalya
### If my post helped you, please take a moment to Vote as Helpful and\or Mark as an Answer

SCOM 2012 R2 Management Packs for monitoring IBM Tivoli

Are there management packs available to monitor IBM Tivoli through SCOM 2012 R2?
If yes, what all components in IBM Tivoli family can be monitored?
Thanks in advance

Hi,
I think if there is any Management Pack for IBM Tivoli, then this Management Pack should be provided by IBM, and this may be fee-based also, I would like to suggest you contact IBM for this.
And hope the below link be helpful:
http://unofficialsystemcentercatalog.wordpress.com/2012/12/27/operations-manager-is-there-a-management-pack-for/
Regards,
Yan Li
Regards, Yan Li

UCS Management Pack for System Center 2012 OpsMgr add monitor wizard error

We're successfully using the 2.6.0.179 version of the UCS Management Pack for System Center 2012 Operations Manager in our 2012 SP1 OpsMgr environment; however, in the new 2012 R2 OpsMgr environment we've stood-up and in which we installed the 2.6.2.0 version of the UCS MP, we're getting an error when trying to run the Add Monitoring Wizard under the Management Pack Templates node of the Authoring pane. We get the same error from the 2.6.1.0 version of the UCS MP as well. The text of the error is as follows:
"The page [Cisco.UCS.MP.UI.Proxy.Template.Page.ProxyDetailsPage] in the assembly [Cisco.UCS.MP.UI.Culture="",PublicKeyToken="6c96076cdf2c87a",Version="2.6.0.0"] could not be loaded. Please make sure that the account you are running under has sufficient privileges to load the given assembly, or the management pack that defines this page is installed or the assembly containing the page is in the path of the executible or that the page derives from known Operations Manager page type."
I'm an admin user in OpsMgr, so this should not be a user privilege issue, and that leaves the MP itself. The fact that a 2.6.0.0 version is mentioned makes me wonder if the base version of the MP must be installed before the 2.6.2 version. I'd test this, but we no longer have that version, and its no longer available for download from Cisco that I can see.
Has any dealt with this issue successfully, or have any insight into the problem?

Solved...the requirement is that you must do the MP configuration from the SCOM console on the SCOM Management Server where you installed the Cisco UCS MP; you can't do it from a SCOM console on a remote computer like I was trying to do.

UCS management pack for SCOM

I've installed the UCS management pack for Microsoft SCOM 2007 R2. It appears to be working, however I now keep seeing all computers that have the SCOM agent installed trying to run the cisco.ucs.computer.probeaction.vbs script, which fails and generates alerts. Does anyone know why these servers that are unrelated to UCS would be trying to run these scripts, or how to fix this problem?

The Problem is that you use an “&” string in a name of one of the protection Groups.
Change the name of the protection Group where you have used an “&” symbol
. Restart the “System Center Management” and you should see that the discovery success.
If still have same issue, started to register the differtent dll’s again on the machine and apparently registering the MOMScriptAPI.dll
http://scug.be/dieter/2012/11/08/scom-event-id-21406-file-name-or-class-not-found/
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

SCOM 2012 UCS pack and C-series monitoring

Hello,
Does anyone know if the SCOM 2012 UCS pack can be used to monitor Cisco C-series server at the hardware level?
If so, can it do this directly without going through UCSM (FICs)?
If not, is there any sort of pack setup for monitoring of C-series servers?
If this requires the 2248TP units connected up to our FICs, I'm open to that, but need to justify the costs.

Hi Justin,
Currently we do not have a MP to support the C series in standalone mode. This is on the roadmap and we should have it in some future releases.
However C series integrated with UCSM can be monitored using the SCOM MP.
Please note: For the integration, you need the 2232 FEX. UCSM version 2.0.2 onwards, we only support 2232 for the C series integration.
Thanks!
./abhinav

Cisco UCS Management Pack Error

Hello,
I'm trying to configure the UCS Management pack for SCOM but when I try to configure in the Authoring pane, the IP + Username password, I have this error:
Data at the root level is invalid. Line 1, position 1.
I'm using the last version of the management pack, 3.0.2.
Any idea?
Thank you.
Regards,
Florent

Hello,
Check this below links
Release Notes for Cisco UCS Manager Management Pack for Microsoft SCOM MP 2.6.1:
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/msft_tools/scom/scom_2.6/scom_2.6_release_notes/scom_releasenotes_2_6.html
User Guide for Cisco UCS Manager Management Pack for Microsoft SCOM MP 2.6.1:
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/msft_tools/scom/scom_2.6/scom_2.6_user_guide/scom_2_6_userguide.html
https://communities.cisco.com/community/technology/datacenter/ucs_management/cisco_ucs_developed_integrations/blog/2013/10/18/cisco-ucs-manager-management-pack-for-microsoft-scom-version-261
Regards
keshav

Event ID 26319 on SCOM 2012 R2 Management server with RMS emulator role

Hi all,
Two weeks ago we've setup a new SCOM 2012 R2 environment.
We now have the problem that event 26319 is logged every 5 minutes.
An exception was thrown while processing GetUserRolesForOperationAndUser for session ID uuid:dca9765e-37a4-40fc-bb9e-575f278447f9;id=63.
Exception message: Value does not fall within the expected range.
Full Exception: System.ArgumentException: Value does not fall within the expected range.
at Microsoft.Interop.Security.AzRoles.IAzApplication2.InitializeClientContextFromStringSid(String SidString, Int32 lOptions, Object varReserved)
at Microsoft.EnterpriseManagement.Mom.Sdk.Authorization.AzManHelper.GetScopedRoleAssignmentsForUser(Int32 operationNumericId, String userName)
at Microsoft.EnterpriseManagement.Mom.Sdk.Authorization.AuthorizationService.GetUserRolesForOperationAndUser(Guid operationId, String userName)
at Microsoft.EnterpriseManagement.ServiceDataLayer.SecurityConfigurationService.GetUserRolesForOperationAndUser(Guid operationId, String userName)
at Microsoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccessBackCompatProxy.GetUserRolesForOperationAndUser(Guid operationId, String userName)
In the previous weeks I've imported some management packs and did some changes in the user roles.
I've now deleted all custom created user roles but the event is still being logged.
Where does the 'Value does not fall within the expected range.'
message points to ?
Is this related to a imported MP ? I've deleted the built-in administrator user and replaced it by an admin group.
Where do I start to troubleshoot this issue ?
Kind Regards,
J. Monnens

Yes, it's related to import MP.
For this issue, KB980862 - Event ID 26319 is logged when you import a management pack in Operations Manager 2007 R2
Also you can check below link
http://thoughtsonopsmgr.blogspot.com/2011/08/eventid-26319-exception-was-thrown.html
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

Cisco UCS Management Pack for System Center Operations Manager 2007 R2 Login Error

I have Cisco UCS 1.4 (3q) and just installed the MP v2.1 for Cisco UCS, however when I click on the "Management Pack Events" alert view in the SCOM console, there are error for event number 19900. The description of the error is as follows:
Description:
CISCO UCS R2 MP (https://10.x.x.x/nuova) [CISCO.UCS.R2.Proxy.LoadCache.ProbeAction.vbs] : CISCO UCS Login Error: Authentication failed (Code: 551)
I noticed that it's looking for the /nuova directory, but in order to login to our UCS environment, we usually just go to the IP address - so I'm wondering if that has something to do with it? I've verified that when going directly to the IP from Internet Explorer I can login using the opsmgr credentials we specifically created for this account. I've also gone through the process of creating a run-as account on the SCOM side and associated it with the correct profiles.
Any help is greatly appreciated.

Troubleshooting has found out its user error, wrong password configured.

SCOM 2012 - Additional Management Server - Database not Found (no errors)

Hello,
I am installing a second management server (SCOM 2012) and am running into an issue connecting to the existing database.
I selected Add a Management server to an existing management group.
On the installer page Configuration/Configure the Operational Database, I enter the sql server name (fqdn) just as I did on the first management server (i took screenshots of the entire install so I could verify what I am
doing). Then the installer takes over for a second to verify the server information. There are no errors but the Database Name is blank, no choices in the drop down, nothing auto-populated.
If I put an incorrect server name in there is an error (as is expected). The port I am connecting on is the same one as the first management server: 1433.
The servers are both running Windows Server 2008 R2 (64bit). They were both created from the same template at the same time.
I used the ODBC Data Source Administrator to test a connection to the SQL server from the Additional Management Server and the test completed successfully.
I checked in the Operations Console to see if there was an entry in the Management Servers list for this second server and there is only the First management server listed there.
Please let me know if you have any suggestions as to how I can see the database names when the server conneciton is not failing. Thanks in advance.
Zach

Hi,
Are the accounts permissions correct? Are you using the same account you used installing the first management server and is it a local admin on the 2nd management server?
If all the above can be answered with yes please check if the 2nd management server is already known inside OpsMgr. If it is delete it from here and try again.
You can also check the OpsMgrSetup.log for more detailed information.
Your problem might be a known one:
http://social.technet.microsoft.com/Forums/en-US/operationsmanagerdeployment/thread/25b05b2f-dd90-44e5-a5cb-c51c9e4944d2
Hope this helps,

SCOM - Monitors for Management Packs

Hi All,
Can any one share the information how we can get the list of monitors in a management pack in SCOM 2012 R2.
The SCOM 2007 R2 cmdlet doesn't work in SCOM 2012 R2.
Rgs,

Hi
there is no option to pull threshold for monitors/rules, as each rule/monitor has different schema of workflow.
you can use mp viewer to see threshold for monitor/rule and make a note of threshold as it is one time activity( you no need to apply mp viewer on library and discovery mp in general for Microsoft MP) and you can apply override explorer to get override values
for monitor/rules this gives current effective threshold.
refer below link for scom 2012 tools.
http://blogs.msdn.com/b/dmuscett/archive/2012/02/19/boris-s-tools-updated.aspx
regards
sridhar v

2012 R2 Management Packs

Hi
Is there a Place where I can find Management Packs för SCOM 2012 & 2012 R2 ?
//P

Hi,
Please refer to:
Microsoft Management Packs
http://social.technet.microsoft.com/wiki/contents/articles/16174.microsoft-management-packs.aspx
Operations Manager: “Is there a management pack for … ?”
http://unofficialsystemcentercatalog.wordpress.com/2012/12/27/operations-manager-is-there-a-management-pack-for/
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

SCOM 2012 Operations Manager Failed to start a process

We have recently upgraded from SCOM 2007 to SCOM 2012. We are not getting a great deal of “Operations Manager Failed to start a process”. The process varies including:
DiscoverSQL2008ASDiscovery.vbs
DiscoverSQL2008DBEngineDiscovery.vbs
DiscoverSQL2008ASDiscovery.vbs
Microsoft.Windows.Server.NetwokAdapter.BandwidthUsed.ModuleType.vbs
I have researched and researched. I know that you can try to run the scripts locally on the machine but it seems the scripts never make it to the machine. I go to the path in the error, no luck. I look in the other folders as I know that SCOM moves the scripts,
and I even search the entire C drive but the scripts are not getting to the server. The folder is not even making it. For example:
Command executed: "C:\Windows\system32\cscript.exe" /nologo "Microsoft.Windows.Server.NetwokAdapter.BandwidthUsed.ModuleType.vbs" SERVER true Working Directory: C:\Program Files\System Center Operations Manager\Agent\Health Service State\Monitoring
Host Temporary Files 11606\1759\
The script is not there and the folder \1759 is not there either.
I have removed and reinstalled the client.
Antivirus is fine, up to date and not blocking on any of the machines.
I have stopped the “System Center Management service” and renamed the “Health Service State” folder and it recreates fine but not long after I get the warning in SCOM about “Operations Manager Failed to start a process”.
I look in event viewer for Operations Manager on this particular one and I see a lot of:
Performance data from the Health Service could not be collected since required registry keys could not be read, the error was 2L (The system cannot find the file specified.). Event ID 6001.
I tried the fix of
"lodctr MOMConnectorCounters.ini" and "lodctr HealthServiceCounters.ini" but I get “error
encountered while updating text in registry. Status: 0”. Again I am using SCOM 2012.
Do I need to look at each failed script or is there a overall issue because the scripts are not making it to the machines. Any ideas?

I guess you might need to run "mofcomp sqlmgmproviderxpsp2up.mof".
Thanks, S K Agrawal

SCOM 2012 Single Management Group Supporting ?

Dear all,
Can any one tell me , for single SCOM management group howmany management server and Gateway server can support?
Thanks,
Sengo

Hi,
Take a look in the System Center 2012 Operations Manager sizing tool which you can find
here.
Agents
3 000
agents reporting to a management server
2 000
agents reporting to a gateway server
15 000
agents (Windows, UNIX or Linux) in a single management group
Regards,
Daniel
IT Consultant at Viridis IT

Operations Manager 2012 R2 Management Pack importing issue

Hi
I seem to be having an issue importing certain management packs, when i do i get the below error:
Windows Server 2008 Operating System (Monitoring) could not be imported.
If any management packs in the Import list are dependent on this management pack, the installation of the dependent management packs will fail.
Verification failed with 2 errors:
Error 1:
Found error in 2|Microsoft.Windows.Server.2008.Monitoring|6.0.7296.0|Microsoft.Windows.Server.2008.Monitoring|| with message:
Could not load management pack [ID=Microsoft.Windows.Server.2008.Discovery, KeyToken=31bf3856ad364e35, Version=6.0.7296.0]. The management pack was not found in the store.
: An error occurred while loading management pack b4bda654-49bd-6e04-ca24-e152fc227001 from the database
Error 2:
Found error in 2|Microsoft.Windows.Server.2008.Monitoring|6.0.7296.0|Microsoft.Windows.Server.2008.Monitoring|| with message:
Could not load management pack [ID=Microsoft.Windows.Server.Library, KeyToken=31bf3856ad364e35, Version=6.0.7218.0]. The management pack was not found in the store.
: Version mismatch. The management pack ([Microsoft.Windows.Server.Library, 31bf3856ad364e35, 6.0.6957.0]) requested from the database was version 6.0.7218.0 but the actual version available is 6.0.6957.0.
Please can someone advise.
Regards
Adrian

Hi,
Solution: An exception is thrown while importing the Red Hat Linux Management Pack for Operations Manager 2007
http://blogs.technet.com/b/operationsmgr/archive/2010/12/15/solution-an-exception-is-thrown-while-importing-the-red-hat-linux-management-pack-for-operations-manager-2007.aspx
Based on this case, the issue might be resolved by re-importing the Microsoft.Windows.Server.Library Management Pack.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

SCOM 2012 UCS Management Pack Configuration/Administrator Guide

Similar Messages

Maybe you are looking for