SCOM web console not working

I have a brand new SCOM installation where SCOM has a RMS and a dedicated DB with DW installed. Everything except web console is working just fine. When I try to navigate to the web console address throught inetmgr I am able to get up the popup window for
username and password and am able to login. But if i try the URL locally on the RMS or from a remote system I am still presented with the login window, but after the credentials have been supplied, I am redirected to page not found. I am using Windows integrated
security, and just for the sake of it I have tried form based and basic authentication. I have also added all the local addresses to trusted sites but still no luck so far.
So to sum opp the problem, Web console not available from URL and FQDN but is available through IIS. Dont really know what the problem is, as there is not being registered anything neither in
Opsmgr log, application log or system log. I cant seem to find anything usefull in IIS log files either. All the servers in the solution are running 2008 R2 and the domain functional level is 2008.
Hope that some one can point me into the right direction.
Best regards
Sean.
Rao

Hi,
I would like to verify what exact error message is recevied when trying to open web console. which authentication was used when installing web console?
To troubleshooting this kind of issue, please refer to the following article:
Common Issues with the OpsMgr Web Console:
http://blogs.technet.com/b/kevinholman/archive/2010/04/07/common-issues-with-the-opsmgr-web-console.aspx
Here are more information:
http://blogs.technet.com/b/kevinholman/archive/2008/09/24/installing-the-web-console-on-a-2008-management-server-using-windows-authentication.aspx
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Thanks for the reply Vivian, I have actually seen this blog and none of the errors described here are the same as I am getting. I can try to describe the situation a bit better:
When http://Localhost:51908/default.aspx is used the web console comes up. No login is required. Everything seems to be OK.
When http://hostname:51908/default.aspx is used:I get the error: Internet Explorer cannot display the web page.
When http://hostname.domainname.local:51908/default.aspx is used: I get the error: Internet Explorer cannot display the web page.
During the initial install and following installs Windows authentication was used as the Web console was been installed on the RMS. I have now installed the IIS mgmt pack which is showing IIS as healthy both on the RMS and on the MS. I have also tried to add
the webconsole on the MS and used form based authentication. But it is also showing the same exact behaviour with the web console as that of RMS. (Had also enabled for delegation as Pete has mentioned)
I have checked the SPN and seems like they also are registered correclty. Any suggestions?
Thanks,
Best regards,
Sean
Rao

Similar Messages

EM web console not working

Hi,
I installed OEM 10g successfully on a wintel box and used it for 2 weeks. It worked perfectly for me. During this time I hadnt restarted the box.
2 days back, the IT guy changed the netbios name of the machine and restarted it. Now i cannot load the OEM web console. I tried the url with the new machine name as well but it doesnt work. I guess I need to tell the EM that the netbios name has changed? But I dont know how that can be done.
I tried starting the Oracle service from the services page but that doesnt start as well. I changed the machine name for the listeners and I can connect to the database from a remote machine. Just this web console thing is not working.
any thoughts ?
many thanks

Drop and Recreate the dbconsole. That should resolve it

SCOM 2012 SP1 Web Console not filtering "Items by Text Search"

I have the weirdest issue with not one, but two installations of SCOM 2012 (SP1) specific to the Web-based Console. I have to think that it's something that I've messed up since each installation (separate domains, separate environments) is exhibiting
the exact same behavior and that I cannot find a single mention by anyone else experiencing this problem anywhere on the 'net.
The problem I'm encountering is that when I try to filter the list of objects using the "Look for: Items by text Search" option, the list doesn't filter! It's just the *weirdest* thing!
For example, I go into "Microsoft Windows Server; Performance" and select "Disk Capacity". The view loads just fine with two panes up top, and the object list down below. I select a pane to display the list of objects which
gives me all the servers discovered/managed by SCOM. I changed the "Look for:" drop-down from "All Items" to "Items by Text Search" which makes the text field (to the right) active. I enter my text string and........
nothing happens. When I hit "Enter" the pane simply refreshes. The "Reset" button doesn't become active further reinforcing the fact that something just ain't right.
I have a installation of SCOM 2007 R2 and this feature works flawlessly.
Anyone have any idea as to what I may have missed or what I might do to resolve this issue? Again, I've found absolutely nothing on the Internet specific to this issue (unless my search criteria is woefully flawed) which suggests that I've messed something
up.
Thank you in advance for your time!
-Todd
PS - this feature works just fine in the installed/thick client/console.

Unfortunately, I never did receive an answer to this issue/post, and I never found a solution with this version of SCOM.
I did, however, just test this functionality on the SCOM 2012 R2 installation and discovered that the "Items by text search" filter in the web console *does* work as one would expect. So, if you're able, upgrade to SCOM 2012 R2 and you should
be much happier with the result. (I think I'm running Cumulative Update #2, if that helps.)
Hope this helps!
-Todd

Content Search Web Part not work for Office Web Apps

Hi ,
In Content Search Web Part word documents are not able to open in browser,but in document library its working.
Office Web Apps not work in Content search web part
Please help me
Regards
Sachin

Below is the display template to open the document in OWA.
<html xmlns:mso="urn:schemas-microsoft-com:office:office" xmlns:msdt="uuid:C2F41010-65B3-11d1-A29F-00AA00C14882">
<head>
<title>AdSpace Picture on top, 3 lines on bottom</title>

</head>
<body>

<script>
$includeLanguageScript(this.url, "~sitecollection/_catalogs/masterpage/Display Templates/Language Files/{Locale}/CustomStrings.js");
</script>

<div id="Item_PictureOnTop">

<div class="top-content-box" id="_#= containerId =#_" data-displaytemplate="ItemPictureOnTop">
<div class="top-content-img" id="_#= pictureContainerId =#_">
<a class="cbs-pictureImgLink" href="_#= $urlHtmlEncode(url) =#_" title="_#= $htmlEncode(line1) =#_" target="_blank" id="_#= pictureLinkId =#_">
_#= pictureMarkup =#_
</a>
</div>
<h3 id="_#= line1Id =#_"><a class="cbs-pictureOnTopLine1Link" target="_blank" href="_#= $urlHtmlEncode(url) =#_" title="_#= $htmlEncode(line1) =#_"
id="_#= line1LinkId =#_"> _#= line1 =#_ </a></h3>
<span class="content-date" title="_#= $htmlEncode(line2) =#_" id="_#= line2Id =#_"><img class="cbs-Thumbnail" src="_#= $urlHtmlEncode(iconURL) =#_"
alt="_#= $htmlEncode(line1.defaultValueRenderer(line1)) =#_" id="_#= pictureId =#_" />_#=line2=#_</span>
</div>
</div>
</body>
</html>
Basically,ctx.CurrentItem.ServerRedirectedURL is calculated by a managed property ServerRedirectedURL which needs to be included in the display template.
Problem solved.
Nehal Bhandari,ATL, Nagarro Softwares

Web links not working in iPhone calendar notes. Used to work. Ideas?

Web links not working in iPhone calendar notes. Used to work. Ideas?

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Has any of this been tried?

Some web sites not working in FF but they are OK in Safari.

A couple of times lately I have had web sites not work correctly with Firefox. I need to switch to Safari to complete the tasks I needed to do. My FF is running on Mountain Lion and is up to date.
Thanks,
MJT

Hello michaeljt, the sites you have problem, is it with a lot of flash content ?
Many site issues can be caused by corrupt cookies or cache. In order to try to fix these problems, the first step is to clear both cookies and the cache.
Note: ''This will temporarily log you out of all sites you're logged in to.''
To clear cache and cookies do the following:
#Go to Firefox > History > Clear recent history or (if no Firefox button is shown) go to Tools > Clear recent history.
#Under "Time range to clear", select "Everything".
#Now, click the arrow next to Details to toggle the Details list active.
#From the details list, check ''Cache'' and ''Cookies'' and uncheck everything else.
#Now click the ''Clear now'' button.
Further information can be found in the [[Clear your cache, history and other personal information in Firefox]] article.
Please reload the webpage while bypassing the cache using '''one''' of the following steps:
*Hold down the ''Shift'' key and click the ''Reload'' button with the left mouse key.
OR
*Press ''Ctrl'' + ''F5'' or ''Ctrl'' + ''Shift'' + ''R'' (Windows and Linux)
*Press ''Command'' + ''Shift'' + ''R'' (Mac)
See if this helps solve the issues you had and please report back to us!
thank you

"no serializer is registered..." error with a web service not working

I'm using JDeveloper 10.1.3
EJB 3.0
I'm having issues with the web service not working after I create a client for it. The web service works fine up until I generate the proxy on the other side.
ERROR An error occurred for port: {http://buslogic/}MyWebService1SoapHttpPort: no serializer is registered for (class buslogic.runtime.....
I saved the file before I added the proxy and the wsdl looks the same between the working one and the non working one. I can not pin point the when the change to the web service is occuring. It seemed to work once all the way up until I had a ADF page trying to retrieve data, another time it failed when the proxy was created.
I can get the version that I saved to work immediately after the version that does not fails.
Any help would be greatly appreciated,
Dan

I'm using JDeveloper 10.1.3
EJB 3.0
I'm having issues with the web service not working after I create a client for it. The web service works fine up until I generate the proxy on the other side.
ERROR An error occurred for port: {http://buslogic/}MyWebService1SoapHttpPort: no serializer is registered for (class buslogic.runtime.....
I saved the file before I added the proxy and the wsdl looks the same between the working one and the non working one. I can not pin point the when the change to the web service is occuring. It seemed to work once all the way up until I had a ADF page trying to retrieve data, another time it failed when the proxy was created.
I can get the version that I saved to work immediately after the version that does not fails.
Any help would be greatly appreciated,
Dan

Flash player download web site not working

After uninstalling flash player, I can't get the web site to reinstall it. I go to the web site click the agree and install now and gos to the next page but nothing pops up like it said it should.
http://get.adobe.com/flashplayer/thankyou/activex/?installer=Flash_Player_10_for_Windows_I nternet_Explorer&i=McAfee_Security_Scan_Plus&d=Google_Toolbar_6.3

Hi eidnolb,
My OS is windows 7 Ultimate. There no Service packs listed Microsoft don't have one for it yet. My brower is Internet explorer 8 version: 8.0.7600.16385. My firewall is not causeing problems and the popup blocker didn't even activate.
Date: Wed, 14 Apr 2010 10:01:33 -0600
Subject: Flash Player flash player download web site not working
Hi newcomer76, Please post back your operating system and if any applicable Service Packs, any and all browsers that you use with the versions.
With that information, I'll be able to give you instructions and the links you need.
Thanks,
eidnolb
>

The web controls not work(windows phone)

Hi
I have a web app.after I make an animation in this page(like a transition page in loading page), the web controls not work more.
the site is shown but any thing not work like scrolling or tap in links

Can you please explain more clearly what you are doing and what you need help with? What is your overall scenario, what exactly is your code doing, what behaviour do you expect and how is that different from what you actually see?

Overdrive Media console not working with iTunes when transferring audio books. Any suggestions?

Overdrive Media console not working with iTunes when transferring audiobooks. Some parts don't transfer.

Robin, I have the 4S too. Here's wha I've been doing. Well, I am downloading wma books, but it is super time consuming and annoying. First, shut off genius in your preferences in iTunes. Also change to spoken podcast for speed. Then, you start to transfer from Overdrive. It will create a playlist with your book title. Open up books though because you need to keep an eye on it. It may download like three parts and then you may have a grey one. When you get the grey, cancel the transfer, delete the greyed part, exit iTunes, re-enter iTunes, and then try to download the remaining book parts. I usually have to re-enter iTunes three or four different times during a book. When your book is downloaded, all black and none grey, open up the playlist folder and double check that all parts made it in there. If not, carry them from the books folder to the playlist and then move it into numerical order.
Re non bookmarking problem. I now have a new habit of checking what part I am on before i shut off my phone or switch to another book. It does save where you were, it just doesn't show you. For instance, if I start part three and then play music, and then go back to the book playlist, it will appear as if we are back to the beginning, but if I go to part three, it will start up from where I was. So, just start checking and then it is easy. I am flabbergasted that no other proper solution has been offered by Overdrive. This has been a problem since October. I also wish they would acknowledge the problem on their website as well as post what version number of update they have. I have 3.2.1.0 and think that's current. Does anyone have newer than this. Good luck, and happy commuting!
An easy, quick workaround is to plug external speakers into your laptop and take it with you in the car. A bit unwieldy, but I can't commute without books.

Vmware console not working

Restart the host management services, if you want to post screenshots or more info do so on here, no third party links, most people will not look on them (me included)

Vmware console not working.
ESX6
can ping the fqdn and have tried turning off the windows firewall.
https://gyazo.com/2980ae196b12f015d59fcca8f723d4fc
help?
This topic first appeared in the Spiceworks Community

SCOM web console - Performance View Time Range

Hi,
I am trying to change the default time range from 24hrs to 48hrs. I have searched for solution, however, all of them are same as this, and it didn't work for me.
http://social.technet.microsoft.com/Forums/systemcenter/en-US/bae50efb-7de3-4e60-bb07-13019fb3f432/web-console-performance-view?forum=operationsmanagergeneral
Has this solution worked for anyone using SCOM 2012 SP1? I made the change to 48hrs, after a iisreset, it is still showing 24hrs.
Any ideas?
Thanks.

I want to know which web.config file , you are modify.
There are two web.config
1) c:\program files\Microsoft System Center 2012 R2\Operations Manager\WebConsole\webhost: not working by adding <add key="PerformanceHourBefre" value="48" />
2) c:\program files\Microsoft System Center 2012 R2\Operations Manager\WebConsole\MonitoringView: it is working by adding <add key="PerformanceHourBefre" value="48" />
Roger

827H router web setup not working

We were having problems with our 827H router, so I decided to reset it to the factory defaults and re-run the quick setup. I've done that before with no problems.
This time, after it loads the configuration in the web setup, it keeps checking the model, IOS version, etc.--over and over again. It won't stop, nor can we exit out of it to get to the quick setup.
Originally the router was connected to a hub. When we couldn't configure it from the web setup, we put the router directly onto a pc with an ethernet cable. We could ping the router. Using the console cable, we are able to see the router's settings. (See attached)
The pc was set to dhcp. The dns was originally set to "Obtain automatically". We also tried to set the dns and the gateway to the router's ip, and added the domain controller's dns as another dns server. Nothing has worked.
Any help will be greatly appreciated.
Thanks!

Your description of the symptoms is quite puzzling as is the console log that you sent. You say that you connected a PC directly to the router. Was that using a cross over Ethernet cable?
You say that when you connected the PC to the router you could ping the router. What IP address was on the PC at that point.
The console output that you included has a kind of garbled output in the show run. It looks as if two things were outputting at the same time. I am not clear if there were actually two things happening together or if the router is really messed up. (Though most of the config that showed up looked reasonable)
I would suggest that you connect to the console port again and capture all of the console output. I would suggest that whle you are connected and capturing output that you power cycle the router (it may be very helpful to see what messages go to the console while the router is booting).
After the router boots again, you may be able to use the web interface. If the web interface does not work you should be able to use the console interface to get a congif that should work basically.
Try these steps and post the output. Maybe then we can find a solution.
HTH
Rick

VM Manager's Launch Console not working with OpenJDK and IcedTea

Fedora 15
java-1.6.0-openjdk-1.6.0.0-59.1.10.3.fc15.x86_64
icedtea-web-1.0.4-1.fc15.x86_64
ICEDTEA-WEB NOTES
Invalid XML
An error like
netx: Unexpected net.sourceforge.jnlp.ParseException: Invalid XML document syntax. at net.sourceforge.jnlp.Parser.getRootNode(Parser.java:1203)
indicates that the JNLP file is not valid XML. The error happens because netx uses an XML parser to parse the JNLP file. Other JNLP client implementations may use more lenient parsers and may or may not work with the given JNLP file. Errors caused by malformed JNLP files can often lead to subtle bugs, so it is probably best to fix the JNLP file itself. A tool like xmlproc_parse might be able to pinpoint the error.
XMLPROC_PARSE OUTPUT
$ xmlproc_parse ovm_rasproxy-ws.jnlp
xmlproc version 0.70
Parsing 'ovm_rasproxy-ws.jnlp'
E:ovm_rasproxy-ws.jnlp:3:89: Undeclared entity 'machineName'
E:ovm_rasproxy-ws.jnlp:3:89: ';' expected
Parse complete, 2 error(s) and 0 warning(s)
JAVAWS OUTPUT
$ javaws ovm_rasproxy-ws.jnlp
netx: Unexpected net.sourceforge.jnlp.ParseException: Invalid XML document syntax. at net.sourceforge.jnlp.Parser.getRootNode(Parser.java:1243)
JAVAWS -VERBOSE OUTPUT
$ javaws -verbose ovm_rasproxy-ws.jnlp
No User level deployment.properties found.
Starting security dialog thread
JNLP file location: ovm_rasproxy-ws.jnlp
Status: CONNECTED DOWNLOADED STARTED +(CONNECTED DOWNLOADED STARTED) @ ./ovm_rasproxy-ws.jnlp
<?xml version="1.0" encoding="UTF-8"?>
line: 2 <jnlp spec="1.0+" codebase="http://192.168.4.21:7001/ovm/rasproxy/"
line: 3 href="ovm_rasproxy-ws.jnlp?vmachineId=0004fb0000060000046ffdb8a331ce21&machineName=mytestmachine">
line: 4 <information>
line: 5 <title>Oracle VM Remote Access Service</title>
line: 6 <vendor>Oracle</vendor>
line: 7 <homepage>http://support.oracle.com/</homepage>
line: 8 </information>
line: 9 <resources>
line: 10
line: 11 <j2se version="1.5+"
line: 12 href="http://java.sun.com/products/autodl/j2se" />
line: 13 <jar href="ovm_rasproxy-signed.jar" main="true" />
line: 14 <jar href="OvmCoreApi.jar" />
line: 15 <jar href="MgmtUtil.jar" />
line: 16 <jar href="Odof.jar" />
line: 17 <jar href="commons-logging-1.1.1.jar" />
line: 18 </resources>
line: 19
line: 20
line: 21 <application-desc main-class="com.oracle.ovm.ras.proxy.RasProxyApplet">
line: 22 <argument>-server</argument>
line: 23 <argument>192.168.4.21</argument>
line: 24 <argument>-service</argument>
line: 25 <argument>003600010004fb0000060000046ffdb8a331ce21</argument>
line: 26
line: 27 </application-desc>
line: 28 <security>
line: 29      <all-permissions/>
line: 30 </security>
line: 31 <update check="background"/>
line: 32 </jnlp>               net.sourceforge.jnlp.ParseException: Invalid XML document syntax.
     at net.sourceforge.jnlp.Parser.getRootNode(Parser.java:1243)
     at net.sourceforge.jnlp.JNLPFile.<init>(JNLPFile.java:177)
     at net.sourceforge.jnlp.JNLPFile.<init>(JNLPFile.java:162)
     at net.sourceforge.jnlp.JNLPFile.<init>(JNLPFile.java:148)
     at net.sourceforge.jnlp.runtime.Boot.getFile(Boot.java:267)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:196)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:56)
     at java.security.AccessController.doPrivileged(Native Method)
     at net.sourceforge.jnlp.runtime.Boot.main(Boot.java:173)
Caused by: net.sourceforge.nanoxml.XMLParseException: XML Parse Exception during parsing of a jnlp element at line 32: Unexpected end of data reached
     at net.sourceforge.nanoxml.XMLElement.unexpectedEndOfData(XMLElement.java:1094)
     at net.sourceforge.nanoxml.XMLElement.readChar(XMLElement.java:877)
     at net.sourceforge.nanoxml.XMLElement.resolveEntity(XMLElement.java:1013)
     at net.sourceforge.nanoxml.XMLElement.scanString(XMLElement.java:658)
     at net.sourceforge.nanoxml.XMLElement.scanElement(XMLElement.java:915)
     at net.sourceforge.nanoxml.XMLElement.parseFromReader(XMLElement.java:512)
     at net.sourceforge.nanoxml.XMLElement.parseFromReader(XMLElement.java:464)
     at net.sourceforge.jnlp.Parser.getRootNode(Parser.java:1239)
     ... 8 more
Caused by:
net.sourceforge.nanoxml.XMLParseException: XML Parse Exception during parsing of a jnlp element at line 32: Unexpected end of data reached
     at net.sourceforge.nanoxml.XMLElement.unexpectedEndOfData(XMLElement.java:1094)
     at net.sourceforge.nanoxml.XMLElement.readChar(XMLElement.java:877)
     at net.sourceforge.nanoxml.XMLElement.resolveEntity(XMLElement.java:1013)
     at net.sourceforge.nanoxml.XMLElement.scanString(XMLElement.java:658)
     at net.sourceforge.nanoxml.XMLElement.scanElement(XMLElement.java:915)
     at net.sourceforge.nanoxml.XMLElement.parseFromReader(XMLElement.java:512)
     at net.sourceforge.nanoxml.XMLElement.parseFromReader(XMLElement.java:464)
     at net.sourceforge.jnlp.Parser.getRootNode(Parser.java:1239)
     at net.sourceforge.jnlp.JNLPFile.<init>(JNLPFile.java:177)
     at net.sourceforge.jnlp.JNLPFile.<init>(JNLPFile.java:162)
     at net.sourceforge.jnlp.JNLPFile.<init>(JNLPFile.java:148)
     at net.sourceforge.jnlp.runtime.Boot.getFile(Boot.java:267)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:196)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:56)
     at java.security.AccessController.doPrivileged(Native Method)
     at net.sourceforge.jnlp.runtime.Boot.main(Boot.java:173)
netx: Unexpected net.sourceforge.jnlp.ParseException: Invalid XML document syntax. at net.sourceforge.jnlp.Parser.getRootNode(Parser.java:1243)

Both realvnc 4.1.3 and tigervnc 1.1.0.1 work on the Linux side.
I was able to get the console to work by wiping the contents of the directory I created at the beginning of this exercise and then copying in a fresh OVM 3.0.2 created ovm_rasproxy-ws.jnlp file.
[gordon@ufo Downloads]$ rm /home/gordon/.icedtea/cache/http/192.168.4.16/ovm/rasproxy/*
[gordon@ufo Downloads]$ javaws ovm_rasproxy-ws.jnlp
java.io.EOFException
     at java.io.DataInputStream.readUnsignedShort(DataInputStream.java:340)
     at java.io.DataInputStream.readUTF(DataInputStream.java:589)
     at java.io.DataInputStream.readUTF(DataInputStream.java:564)
     at sun.security.provider.JavaKeyStore.engineLoad(JavaKeyStore.java:744)
     at sun.security.provider.JavaKeyStore$JKS.engineLoad(JavaKeyStore.java:55)
     at java.security.KeyStore.load(KeyStore.java:1201)
     at net.sourceforge.jnlp.security.KeyStores.createKeyStoreFromFile(KeyStores.java:358)
     at net.sourceforge.jnlp.security.KeyStores.getKeyStore(KeyStores.java:124)
     at net.sourceforge.jnlp.security.KeyStores.getKeyStore(KeyStores.java:103)
     at net.sourceforge.jnlp.security.KeyStores.getCertKeyStores(KeyStores.java:157)
     at net.sourceforge.jnlp.security.VariableX509TrustManager.<init>(VariableX509TrustManager.java:91)
     at net.sourceforge.jnlp.security.VariableX509TrustManager.getInstance(VariableX509TrustManager.java:395)
     at net.sourceforge.jnlp.runtime.JNLPRuntime.initialize(JNLPRuntime.java:210)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:182)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:56)
     at java.security.AccessController.doPrivileged(Native Method)
     at net.sourceforge.jnlp.runtime.Boot.main(Boot.java:173)
netx: Unexpected java.io.IOException: /home/gordon/.icedtea/cache/http/192.168.4.16/ovm/rasproxy/ovm_rasproxy-ws.jnlp (No such file or directory) at net.sourceforge.jnlp.JNLPFile.openURL(JNLPFile.java:255)
[gordon@ufo Downloads]$ cp ovm_rasproxy-ws.jnlp /home/gordon/.icedtea/cache/http/192.168.4.16/ovm/rasproxy/
[gordon@ufo Downloads]$ javaws ovm_rasproxy-ws.jnlp
java.io.EOFException
     at java.io.DataInputStream.readUnsignedShort(DataInputStream.java:340)
     at java.io.DataInputStream.readUTF(DataInputStream.java:589)
     at java.io.DataInputStream.readUTF(DataInputStream.java:564)
     at sun.security.provider.JavaKeyStore.engineLoad(JavaKeyStore.java:744)
     at sun.security.provider.JavaKeyStore$JKS.engineLoad(JavaKeyStore.java:55)
     at java.security.KeyStore.load(KeyStore.java:1201)
     at net.sourceforge.jnlp.security.KeyStores.createKeyStoreFromFile(KeyStores.java:358)
     at net.sourceforge.jnlp.security.KeyStores.getKeyStore(KeyStores.java:124)
     at net.sourceforge.jnlp.security.KeyStores.getKeyStore(KeyStores.java:103)
     at net.sourceforge.jnlp.security.KeyStores.getCertKeyStores(KeyStores.java:157)
     at net.sourceforge.jnlp.security.VariableX509TrustManager.<init>(VariableX509TrustManager.java:91)
     at net.sourceforge.jnlp.security.VariableX509TrustManager.getInstance(VariableX509TrustManager.java:395)
     at net.sourceforge.jnlp.runtime.JNLPRuntime.initialize(JNLPRuntime.java:210)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:182)
     at net.sourceforge.jnlp.runtime.Boot.run(Boot.java:56)
     at java.security.AccessController.doPrivileged(Native Method)
     at net.sourceforge.jnlp.runtime.Boot.main(Boot.java:173)
java.io.EOFException
     at java.io.DataInputStream.readUnsignedShort(DataInputStream.java:340)
     at java.io.DataInputStream.readUTF(DataInputStream.java:589)
     at java.io.DataInputStream.readUTF(DataInputStream.java:564)
     at sun.security.provider.JavaKeyStore.engineLoad(JavaKeyStore.java:744)
     at sun.security.provider.JavaKeyStore$JKS.engineLoad(JavaKeyStore.java:55)
     at java.security.KeyStore.load(KeyStore.java:1201)
     at net.sourceforge.jnlp.security.KeyStores.createKeyStoreFromFile(KeyStores.java:358)
     at net.sourceforge.jnlp.security.KeyStores.getKeyStore(KeyStores.java:124)
     at net.sourceforge.jnlp.security.KeyStores.getKeyStore(KeyStores.java:103)
     at net.sourceforge.jnlp.security.KeyStores.getCertKeyStores(KeyStores.java:157)
     at net.sourceforge.jnlp.tools.JarSigner.checkTrustedCerts(JarSigner.java:414)
     at net.sourceforge.jnlp.tools.JarSigner.verifyJars(JarSigner.java:269)
     at net.sourceforge.jnlp.runtime.JNLPClassLoader.verifyJars(JNLPClassLoader.java:946)
     at net.sourceforge.jnlp.runtime.JNLPClassLoader.initializeResources(JNLPClassLoader.java:422)
     at net.sourceforge.jnlp.runtime.JNLPClassLoader.<init>(JNLPClassLoader.java:169)
     at net.sourceforge.jnlp.runtime.JNLPClassLoader.getInstance(JNLPClassLoader.java:283)
     at net.sourceforge.jnlp.Launcher.createApplication(Launcher.java:650)
     at net.sourceforge.jnlp.Launcher.launchApplication(Launcher.java:436)
     at net.sourceforge.jnlp.Launcher$TgThread.run(Launcher.java:830)
Oct 4, 2011 4:13:41 PM com.oracle.ovm.ras.proxy.RasProxyApplet main
INFO: Server : 192.168.4.16
Oct 4, 2011 4:13:41 PM com.oracle.ovm.ras.proxy.RasProxyApplet main
INFO: service id : 003600010004fb0000060000281734f86e6aab47
Oct 4, 2011 4:13:42 PM com.oracle.ovm.ras.proxy.external.VncViewerLauncherFactory getVncViewerLauncher
INFO: Os is : linux
Oct 4, 2011 4:13:53 PM com.oracle.ovm.ras.proxy.ProxyThread setupSSL
INFO: DONE SSL Handshaking
The console starts and all is well with the world.
This is obviously not how one would want to start a console by downloading the .jnlp file and running it on the command line so I am now going to remove the /home/gordon/.icedtea/cache/http/* and see what happens.
First, let me say that nothing happened. It did not work. I did confirm that it creates the directory structure again /home/gordon/.icedtea/cache/http/192.168.4.16/ovm/rasproxy/ but there is only one file in the directory.
[gordon@ufo rasproxy]$ cat ovm_rasproxy-ws.jnlp.info
#automatically generated - do not edit
#Tue Oct 04 16:43:29 EDT 2011
last-modified=0
last-updated=1317761009801
content-length=883
If I save that ovm_rasproxy-ws.jnlp file instead of opening it and copy it to the /home/gordon/.icedtea/cache/http/192.168.4.16/ovm/rasproxy/ directory the console will now start successfully with one minor drawback - it will only launch that one VM based on the .jnlp file that I downloaded.
Help?

SCOM ACS Reporting - Not Working

I am encountering following error while running audit reports in SCOM console-
Cannot create connection to data source 'datasource1',(rsErrorOpeningConnection).
Can anyone help me out on this?

Hi,
I would like to verify what exact error message is recevied when trying to open web console. which authentication was used when installing web console?
To troubleshooting this kind of issue, please refer to the following article:
Common Issues with the OpsMgr Web Console:
http://blogs.technet.com/b/kevinholman/archive/2010/04/07/common-issues-with-the-opsmgr-web-console.aspx
Here are more information:
http://blogs.technet.com/b/kevinholman/archive/2008/09/24/installing-the-web-console-on-a-2008-management-server-using-windows-authentication.aspx
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Thanks for the reply Vivian, I have actually seen this blog and none of the errors described here are the same as I am getting. I can try to describe the situation a bit better:
When http://Localhost:51908/default.aspx is used the web console comes up. No login is required. Everything seems to be OK.
When http://hostname:51908/default.aspx is used:I get the error: Internet Explorer cannot display the web page.
When http://hostname.domainname.local:51908/default.aspx is used: I get the error: Internet Explorer cannot display the web page.
During the initial install and following installs Windows authentication was used as the Web console was been installed on the RMS. I have now installed the IIS mgmt pack which is showing IIS as healthy both on the RMS and on the MS. I have also tried to add
the webconsole on the MS and used form based authentication. But it is also showing the same exact behaviour with the web console as that of RMS. (Had also enabled for delegation as Pete has mentioned)
I have checked the SPN and seems like they also are registered correclty. Any suggestions?
Thanks,
Best regards,
Sean
Rao

SCOM web console not working

Similar Messages

Maybe you are looking for