Screen auto turns to minimum....not shutting down nor sleeping

I have my first generation macbook white, sometimes while i was using my laptop, the screen would automatically goes off to the minimum brightness, actually look like when the bar of the brightness is turn down to the minimum where you actually still can see a very faint screen (with programs opening behind) not sleep. No matter what buttons i have triggered, it's doesn't response at all i have to restart my computer. My batt is faulty so it is removed, i work only on the power plug...why does this happen? could the cause be the battery that is removed?

Hrmm..sorry to mention that it is not to the minimum, It is not a single bar shown...brightness is turn to zero instead.

Similar Messages

  • How in Ipad 3.2 setup time go to sleep mode[turn off but not shut down]

    How in Ipad 3.2 setup time go to sleep mode[turn off but not shut down]?

    Go to Settings>General>Auto Lock - tap the arrow and then choose your time setting to put the iPad to sleep.

  • Macbook Pro screen is black and will not shut down or boot up right.

    Last night my 2007 macbook pro would not go to sleep properly.  When I closed the book the light stayed on and the fan continued running.  Later I shut it down. 
    This morning the computer turned on but the screen is black.  I tried closing the book but again it would not sleep.  I hold down the power button and it seems to shut down but when I push the power button again the light comes back on and the fan starts up but the screen stays black and there is no powerup sound.
    The lights on the battery are lit up.  I tried taking the battery out but same thing.
    Any help is greatly appreciated.

    Try:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    Resetting your Mac's PRAM and NVRAM
    Then see if it will boot into Safe Mode. Do not remove the battery unless it's defective.
    If none of the above work then you may have a hardware failure so take it in for service.

  • I cant start my machine.  The screen only turns grey and then shuts down after 1 minute.  it looks like it working, but nothing happens.

    I cant start my machine.  when i push the starting button, the screen onely turns grey. it looks like its woorking, but nothing happens. 1 year old

    You need to re install OSX. If you have the dmg file downloaded via torrentz this is how you can create a bootable external HD or Flash drive (8 GB+)
    https://discussions.apple.com/message/23957654#23957654
    Peace
    Harry

  • Windows 10 will not shut down or sleep

    Ever since installing Windows 10 my desktop PC will not go into sleep mode and will not even shut down - I have to press and hold the main power switch.I've searched for solutions, but the only ones I've seen so far relate to laptop power management options, which don't apply to desktops.I was running Windows 7 before I upgraded, and never had a problem putting the PC into sleep or shutting down before.I have run the power troubleshooter, but that hasn't helped.Can someone suggest a solution?

    YES!!!!! A Solution that worked.  Spread the news.  It has to do with the Intel Virtualization Tehnology. Didn't know what that was until this issue came up in Windows 10. First, find out if this is your issue.   1. I installed the 'Intel Processor Identification Utility' directly from Intel.2. After installation, open the program and go to the 'CPU Technologies' tab.3. If it says 'YES' for Intel Virtualization Tehnology, proceed. Solution...(at least on my system) 1. The next thing you have to do is go into the BIOS.  If you have not done this before, proceed at your own risk.         You need to restart the computer and enter the BIOS (for me I hit F10 at the HP screen)2. Within the BIOS, there is an 'Advanced Options' section3. In this section there is a line for 'Intel Virtualization Tehnology' and it will say enabled or disabled.  My computer said disabled.4. If this is the case, change the option to 'ENABLED'; then SAVE and EXIT from the BIOS.   The Computer will restart and from that point on Shut Down, Sleep, etc. has worked.  WOW this was a frustrating issue. Almost went back to Windos 8.  I take no credit for this solution, I pieced it together from other posts on this issue.  Hope this helps.

  • Macbook Pro will not shut down/restart/sleep/log out after Mountain Lion update

    Dear all,
    I upgraded from Lion to Mountain Lion yesterday and since then I have encountered a few issues:
    - The only way I can shut down my computer is to hold down the power button or entering commands in terminals. The commands under the Apple menu do not work at all. No window opens when I click on it.
    - The about this mac, force to quit, sleep, shut down and restart button, log out do not work.
    - When I restart my computer, it takes 3-4 minutes to log into the account (it used to be less than 1 minute, I have an SSD).
    I have tried all of these solutions to solve the problem:
    - I created another user account and I do not encounter the same problems. It logs in quickly, can shut down etc.
    - I have repaired the disk and the disk authorisations using disk utility
    - I have cleaned up all caches and did maintenance using OnyX
    - I have cleaned up all ACL using terminal
    - I have never installed Kapersky (this was the cause of the problem for some people in the past)
    I am starting to be a bit short on ideas. All I know is that there is a problem with my user account. I do not want to do a clean install as I have quite a lot of work stored on this user account and preferences that took me ages to set up. If I have to start fresh I will but I would rather avoid this extreme solution.
    Has anyone else experienced such an issue? If yes, how did you solve it?
    Thank you very much

    Had the same problem and this worked for me:
    Try deleting following two items:
    ~/Library/Preferences/com.apple.dock.plist
    ~/Library/Preferences/com.apple.dock.db
    Make sure you take a screenshot of your current dock since deleting these files will reset your dock to default.
    Now open terminal and do a sudo reboot w/ your password.
    This solved the problem for me.

  • Ipod touch screen is frozen and will not shut down or re-set

    I loaded a new game and when I opened the game, my Ipod Touch froze as soon as the game started to boot. The touchscreen is unresponsive and the Ipod will not restart or re-set. It will not register when hooked to Itunes on my computer. Has anyone had this happen, and how can I get it to re-boot.

    Try here:
    iOS: Not responding or does not turn on
    If still "on", let the battery fully drain. After charging for an hour try again.

  • Improperly disconnected ipod nano now screen is blank, and will not shut off.

    I accidently unplugged iPod Nano (second generation) improperly; now the screen is blank and will not shut down.

    Have you tried a hard reset yet? To do this, first make sure the hold switch has not been activated, then press and hold both the Select (Center) and Menu buttons together long enough for the Apple logo to appear.  This may take a couple of tries.
    Otherwise, wait for the iPod's battery to fully drain. Then connect it to a power source charge up as normal. It might be necessary to restore the Nano via iTunes after that as there may be corrupt files still leftover from improperly ejecting the iPod.
    B-rock

  • My ipad is freez...it only show a home screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

    my ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

    Have you tried to reset it? Hold down the sleep and home keys for about 20 seconds and see if you can get it to reboot.

  • My ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

    my ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.plz help me.................thx u

    Option 1
    Try force iPad into Recovery Mode. Follow step 1 to 6 very closely.
    http://support.apple.com/kb/HT1808
    Note: You need to be patient and repeat the above many times to recover your iPad

  • Macbook pro does not shut down, blue screen and turning wheel appears

    My mac book pro 2011 does not shut down especially after using illustrator or photoshop. It shows a blue screen with an never ending turning wheel. What do i do?

    My mac book pro 2011 does not shut down especially after using illustrator or photoshop. It shows a blue screen with an never ending turning wheel. What do i do?

  • Can not shut down late 2011 MacBook Pro and turn it back on again without the hard drive disappearing?

    Ok, I have searched for months for an answer to this question to no avail, probably because no one has experienced it before. I am hoping however that you guys can help me figure this one out cause it is driving me nuts! Also, I am not entirely sure what section of the support I should put this under so if I stick it in the wrong place, I apologize.
    Right now my problem is very simple. When I turn off my laptop, and then try to turn it back on, my internal hard drive disappears... and I get the blinking folder with a question mark on it. I have figured out something interesting however. I have an install disk with Ubuntu Linux on it. If I boot into that first, then RESTART the laptop, not shut down and turn back on, it reads the internal hard drive just fine and I can boot as if there is nothing wrong.
    Second part to the problem... If I allow the laptop in either OSX or Windows to go to sleep (aka shut off the hard drive but the computer remains on), when I attempt to wake it up, I am greeted with the usual log in screen of whichever OS I am in, but is frozen and after a few seconds goes black and restarts the computer to find that... Surprise! The hard drive is gone
    I have tried every trick in the book that I can think of, but can not seem to come up with a solution to the problem... I know when the problem happened and if anyone thinks that that will help them figure this out I will type everything I did up till, including the crash that caused this, and my attempted fixes, but I have class right now so only if you guys want it I will type all that out.
    What I am currently running is:
    2011 MacBook Pro 13in screen
    4Gb of Ram
    1TB internal Hard Drive
    OSX 10.11.whatever the newest update is... just updated the other day again.
    Windows 8.1 on BootCamp 5 (yea I know its not supposed to work but it does) again, fully updated
    Ubuntu 13.10 (I think? Doesn't really matter, its just an install disk I use to boot the computer)
    If there is anything else that you guys need me to provide, I can, just simply ask. I can provide as much info as is necessary.

    Sorry it took me so long to write back, But unfortunately this didn't help my issue.
    My uncle and I did a lot of tests on this computer and have narrowed down the location of the problem a little bit.
    We tried to first reset the SMC and the NVRAM as suggested, but the only thing that did was make the fans run on full tilt for the first session after restarting it for some reason. After that we tried re installing OSX over the OSX that was already on the system (not removing any of the files). This also didn't do anything but make refit stop working. Then we moved onto the next task at hand by removing the hard drive entirely and booting it as an external drive from one of the USB ports... as long as you booted it with the options key held down, it worked perfectly fine. Then we put an alternative hard drive into the computer and installed OSX on that. This time there was no trouble booting anything up. Everything seemed to work flawlessly. So we made a backup of my original drive (OSX, Windows, and all) onto an external hard drive and tested booting to it via USB. That again worked perfectly fine and booted right up with no problems. So after that we formatted the original hard drive and reinstated OSX. We then proceeded to transfer all the old files from the backup onto this new installation and LOW AND BEHOLD..... we were back to square one with it refusing to recognize the hard drive again.
    So this basically told us that there appears to be something either wrong with the hard drive, or something got really screwed up in the software along the lines and by me copying all my old files back over, I just ended up bringing the screwed up file back over with it! (despite not copying over any settings of any kind) So I am still extremely confused as to what is going wrong... did some boot sector possibly get screwed up may be?

  • IMac intel 10.6.8 will not shut down. Blue screen comes on and spinning wheel goes round.

    My iMac intel will not shut down. The version is 10.6.8. To turn it off I have to use the the power off button. Is there any one who can help me to solve the problem.
    The blue screen comes on and the spinning wheel goes round and round until I have to turn it off by the power button.

    I am having the same problem on my Mini.  I found an earlier thread (now archived) that suggested that this spinning wheel on shutdown of SL has something to do with power management settings.  Another idea was that it is related to EyeTV (which I do have running on this Mac).
    Any ideas from the community on how to fix this would be greatly appreciated!  (I have done the typical steps of repairing permissions and (from the Install CD) running Disk Utility, which reported no problems.)

  • HT1414 My Ipod Touch have a black screen when an app shut down and I can not shut down the Ipod. The screen is still black and I did the press two buttons solution and it doesn't work. What I have to do now?

    My Ipod Touch have a black screen when an app shut down and I can not shut down the Ipod. The screen is still black and I did the press two buttons solution and it doesn't work. What I have to do now?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • My iPod touch will not shut down to the black screen which causes my battery to drain with in an hour?

    My iPod touch will not shut down automatically which causes my battery to drain within hours? HELP

    Have you went to Settings>General>Auto-Lock and specified a shot time?

Maybe you are looking for

  • Unable to add facet Spring 3.0

    Trying to select Spring version 3.0 results in "Further configuration required". The Spring configuration wizzard does not enable Next-button when choosing "Spring Framework Bundle from Spring IDE" as Library type. Pressing OK and Apply removes the S

  • Can't view trailers

    I can view the TV show previews OK, but when I try to view a movie trailer nothing happens.

  • How to i get back microsoft Windows xp after trashing it on my mac

    Help! How do I get back Microsoft Windows XP after trashing it on my Mac?

  • PROBLEM AT THE TIME OF CREATION OF VALUATION TYPE(SPLIT VALUATION)

    Dear cons   I want to create a valuation type ( t-code- OMWC) in configuration client. Then I will transport to quality as well as production. but it is a matter of great regret that at the time creation of valuation type no transport request no. is

  • Best way to create an appliance

    I need to create an appliance.  I can: 1.  Export an existing Vm as an appliance from vsphere client 2.  Use a program like VMware studio to create it for me What is the best way to create it?  The goal is to make it as easy to administer within vCen